M/B for LGA 775 Quad Core Ready
USER'S MANUAL
Of
Intel G41 Express Chipset
&
Intel ICH7 Chipset
Based
Intel Core Processor Family
PMG41-D2
MB: Rev: 1.0
Manual: Rev: EG100
Release date: Nov., 2009
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
TABLE OF CONTENT
CHAPTER 1 INTRODUCTION OF INTEL G41 MOTHERBOARD SERIES
1-1 FEATURES OF MOTHERBOARD .................................................................................... 1
1-1.1 SPECIAL FEATURES OF MOTHERBOARD.................................................... 2
1-2 SPECIFICATION...................................................................................................................3
1-3 ITEM CHECKLIST ..............................................................................................................4
1-4 LAYOUT DIAGRAM & JUMPER SETTING ................................................................... 4
CHAPTER 2 HARDWARE INSTALLATION
2-1 INSTALL LGA 775 SUPPORTED INTEL PROCESSOR................................................ 5
2-2 INSTALL MEMORY............................................................................................................ 5
2-3 EXPANSION CARDS ........................................................................................................... 6
CHAPTER 3 CONNCTORS, HEADERS & JUMPERS SETTING
3-1 CONNECTORS ..................................................................................................................... 7
3-2 HEADERS.............................................................................................................................. 11
CHAPTER 4 DRIVER & FREE PROGRAM INSTALLATION
4-1 INF: Install Intel INF Chipset System Driver ......................................................................... 16
4-2 VGA: VGA Driver..................................................................................................................... 17
4-3 LAN: LAN Driver...................................................................................................................... 18
4-4 SOUND: Install Audio Driver................................................................................................... 19
4-5 HOW TO UPDATE BIOS......................................................................................................... 20
4-6 Trouble Shooting........................................................................................................................ 20
Environmental Protection Announcement
Do not dispose this electronic device into the trash while discarding. To minimize pollution
and ensure environment protection of mother earth, please recycle.
ii
Chapter 1
Introduction of Intel G41 Motherboard Series
1-1 Features of motherboard
The Intel G41 chipset motherboard series are based on the latest Intel G41 Express Chipset
and Intel ICH7 Chipset technology which supports the innovative 65nm and 90nm Intel®
Pentium® 4 Processor，Celeron 4xx Processor, Dual-Core Intel® Pentium® D Processor 8 and
9 Series, Intel® Core 2 Quad, Intel® Core 2 Duo® (Code Name: Conroe) Processor with
Intel® Hyper-Threading Technology and fully supports the future 45nm processors. The
motherboard is optimized to deliver innovative features and professional desktop platform
solution with the advantages of the new generation dual core Intel® Core 2 Duo® Processor for
those who demand the best experience of personal computing. Through the high bandwidth of
dual channel DDR2 533MHz/DDR2 667MHz /DDR2 800 system memories which are
expandable to 8GB.
The motherboards implement Intel G41 Express Chipset which supports Front Side Bus
1333MHz of data transferring and offers with 266/333MHz/400MHz memory clock frequency
for Dual channel DDRII533/DDRII667/DDRII800 memory DIMM to double the performance
of memory access. The motherboard is embedded with ICH7 chipset of providing one parallel
Ultra ATA 100 interface for one IDE drives and four serial ATA2 interface of 3Gb / s data
transfer rate for four serial ATA devices.
The G41 motherboard series offer one PCI-Express x16 graphics slot of 8Gbyte/sec data
transfer rate at each relative direction which gets 7 times of bandwidth more than AGP 8X
and up to 16Gbyte/sec peak concurrent bandwidth at full speed to guarantee the ultimate GPU
computing performance. One PCI Express x1 I/O slots and two 32-bit PCI slots guarantee the
rich connectivity for the I/O of peripherals. The motherboards are designed of tackling the
profuse multimedia requirements nowadays.
The motherboards provide 10/100 Ethernet LAN function by using the PCI-E megabit LAN.
The embedded Realtek ALC662 chipset is fully compatible with Sound Blaster Pro standards
providing HD audio 6-CH CODEC offers you with the home cinema quality and satisfying
software compatibility.
Embedded USB controller as well as capability of expanding to 8 of USB2.0 functional ports
delivering 480Mb/s of rich connectivity, these motherboards meet the demands of future USB
peripherals which are also equipped with hardware monitor function on system to monitor
and protect your system and maintain your non-stop business computing.
Some special features---CPU Thermal Throttling/ CPU Vcore 7-shift /OC-CON in this
motherboard are designed for power user to use the over-clocking function in more flexible
ways. But please be caution that the over-clocking maybe causes the fails in system
reliabilities. This motherboard provides the guaranteed performance and meets the demands
of the next generation computing. But if you insist to gain more system performance with
variety possibilities of the components you choose, please be careful and make sure to read
the detailed descriptions of these value added product features, please get them in the coming
section.
1
1-1.1 Special Features of Motherboard
CPU Thermal Throttling Technology---(The CPU Overheat Protection Technology)
To prevent the increasing heat from damage of CPU or accidental shutdown while at high
workload, the CPU Thermal Throttling Technology will force CPU to enter partially idle
mode from 87.5% to 12.5% according to preset CPU operating temperature in BIOS (from 40
℃ to 90℃). When the system senses the CPU operating temperature reaching the preset
value, the CPU operating bandwidth will be decreased to the preset idle percentage to cool
down the processor. When at throttling mode the beeper sound can be optionally selected to
indicate it is in working.
CPU Vcore 7-Shift--- (Shift to Higher Performance)
The CPU voltage can be adjusted up by 7 steps for the precisely over-clocking of extra
demanding computing performance.
OC-CON ---（High-polymer Solid Electrolysis Aluminum Capacitors）
The working temperature is from 55 degrees Centigrade below zero to 125 degrees
Centigrade, OC-CON capacitors possess superior physical characteristics that can be while
reducing the working temperature between 20 degrees Centigrade each time, intact extension
10 times of effective product operation lives, at not rising degrees Centigrade of working
temperatures each time a relative one, life of product decline 10% only too.
2
1-2 Specification
Spec Description
Micro ATX form factor 4 layers PCB size: 24.5*18cm
Design
Chipset
CPU Socket
(LGA775 )
Memory Socket
Expansion Slots
Integrate IDE and
Serial ATA2
Integrated VGA
LAN
HD Audio
z
Intel G41 Memory Controller Hub (MCH) Chipset
z
Intel 82801GB I/O Controller Hub (ICH7) Chipset
z
z Support 45nm and 65nm Quad-Core, Dual-Core Intel® Core 2 Quad, Core
2 Duo processors, Intel® Pentium Dual Core, Intel® Celeron Dual Core
Conroe processors and Intel® Celeron 400 Conroe-L processors 775-Land
LGA Package utilizes Flip-Chip Land Grid Array (FCLGA) package
processor
Suggest the power of the CPU should below 65w
z
Support FSB Frequency1333 MHz
z
240-pin DDR2 RAM module socket x 2
z
Support Dual channel DDR2 533/DDR2 667 /DDR2 800/MHz RAM
z
Module and which is expandable to 8GB.
PCI-Express x16 slot 1pcs.
z
PCI-Express x1 slot 1pcs
z
32-bit PCI slot 2pcs
z
One PCI IDE controller that supports PCI Bus Mastering, ATA PIO/DMA
z
and the ULTRA DMA 33/66/100 functions that deliver the data transfer
rate up to 100 MB/s; four Serial ATA2 ports each provides 3.0 Gb /sec data
transfer rate.
Integrated Graphic Media Accelerator 4500
z
Integrated PCI-E 10/100 LAN chip
z
Support Fast Ethernet LAN function of providing 10Mb / 100Mb data
z
transfer rate
Realtek ALC662 6-CH HD Audio Codec integrated
z
Support 6-CH 3D surround & Positioning Audio
z
Audio driver and utility included
z
BIOS
Multi I/O
AMI 8MB DIP Flash ROM
z
PS/2 keyboard and PS/2 mouse connectors
z
Floppy disk drive connector x1
z
Parallel header x1 / Serial port x1
z
D-Sub 15-pin VGA Conn.
z
USB 2.0 connector x 4, headers x2
z
HDMI-SPDIF header x1
z
SATA Connector x4
z
RJ45 LAN connector x1
z
Audio connector x1 (Line-in, Line-out, MIC)
z
3
K
1-3 Item Checklist
5
Intel G41
5
Cable for IDE
5
CD for motherboard utilities
5
Cable for Serial ATA Port
5
Intel G41
5
Back panel
Platform Processor Chipset based motherboard
Platform Processor Chipset motherboard User’s Manual
1-4 Layout Diagram & Jumper Setting
PS2 KB/Mouse
Port
COM
ATX 12V Power
Connector
B／MS Power ON
Jumper (JP1)
CPU Socket mPGA775
DDR2
DIMMx2
ATX Power
Connector
VGA
USB Port
USB Port
RJ45 Over
6-CH Audio Connector
PCI –E Megabit LAN
Controller
CPU FAN
SYSFAN1
USB Power ON Jumper
(JP2)
Intel G41Express
Chipset
IDE Connector
PCI Express x16
PCI Express x1
CD Audio In
6-CH ALC662 HD
Audio Codec
32-bit PCI Slot
Front Panel Audio
SYS FAN2
Intel 82801GB
ICH Chipset
Front Panel
Connector
Power Led &
Speaker Header
Serial-ATA2
Connector
(SATA1, 2, 3, 4)
Parallel Connector
HDMI-SPDIF Connector
Floppy Connector
USB Connector
4
Chapter 2
Hardware Installation
2-1 Install LGA 775 Supported Intel Processor
This motherboard provides a 775-pin surface mount, LGA775 Land Grid Array socket,
referred to as the LGA775 socket supports Intel Pentium 4 processor in the 775 Pin package
utilizes Flip-Chip Land Grid Array (FC-LGA) package technology.
The CPU that comes with the motherboard should have a cooling FAN attached to prevent
overheating. If this is not the case, then purchase a correct cooling FAN before you turn on
your system.
WARNING! 1.
Be sure that there is sufficient air circulation across the processor’s
heatsink and CPU cooling FAN is working correctly, otherwise it may
cause the processor and motherboard overheat and damage, you may install
an auxiliary cooling FAN, if necessary.
2
. Suggest the power of CPU should below 65w.
To install a CPU, first turn off your system and remove its cover. Locate the LGA775 socket
and open it by first pulling the level sideways away from the socket then upward to a
90-degree angle. Insert the CPU with the correct orientation as shown below. The notched
corner should point toward the end of the level. Because the CPU has a corner pin for two of
the four corners, the CPU will only fit in the orientation as shown.
LGA775
Colden Arrow
CPU LGA775 Socket
2-2 Install Memory
This motherboard provides two 240-pin DDR2 DUAL INLINE MEMORY MODULES
(DIMM) socket for DDR2 memory expansion available from minimum memory volume of
128MB to maximum memory volume of 8GB DDR2 SDRAM.
Valid Memory Configurations
Bank 240-Pin DIMM PCS Total Memory
Bank 0, 1 (DIMM1) DDR2 533/DDR2 667/DDR2 800 X1 4GB
Bank 2, 3 (DIMM2) DDR2 533/DDR2 667/DDR2 800 X1 4GB
Total Memory (Max.8GB)
Recommend DIMM Module Combination
5
2 8GB
1. One DIMM Module ----Plug in DIMM1
2. Two DIMM Modules---Plug in DIMM1 and DIMM2 for Dual channel function
For Dual channel Limited!
3. Dual channel function only supports when 2 DIMM Modules plug in either both DIMM1 &
DIMM2
4. DIMM1 & DIMM2 must be the same type, same size, and same frequency for dual channel
function.
Install DDR2 SDRAM modules to your motherboard is not difficult, you can refer to figure
below to see how to install a 240-Pin DDR2 533/DDR2 667/DDR2 800 SDRAM module.
NOTE!
When you install DIMM module fully into the DIMM socket the eject tab
should be locked into the DIMM module very firmly and fit into its
indention on both sides.
6
2-3 Expansion Cards
The G41 motherboard series offer one PCI-Express x16 graphics slot of 8Gbyte/sec data
transfer rate at each relative direction which gets 7 times of bandwidth more than AGP 8X
and it’s up to a peak concurrent bandwidth of 16Gbyte/sec at full speed to guarantee the
ultimate GPU computing performance. One PCI Express x1 I/O slot and two 32-bit PCI slots
guarantee the rich connectivity for the I/O of peripherals. The motherboards are designed of
tackling the profuse multimedia requirements nowadays.
.
32-bit PCI Slots
PE1 / PCI-E x16 Slot
PCI-E x1 Slot
7
Chapter 3
Connectors, Headers & Jumpers Setting
3-1 Connectors
(1) Power Connector (24-pin block): ATXPWR
ATX Power Supply connector:
This is a new defined 24-pins
connector that usually comes with
ROW1 ROW2
ATX case. The ATX Power Supply
allows using soft power on
momentary switch that connect from
the front panel switch to 2-pins
Power On jumper pole on the
motherboard. When the power
switch on the back of the ATX
power supply turned on, the full
power will not come into the system
board until the front panel switch is
momentarily pressed. Press this
Pin 1
20-Pin
switch again will turn off the power to the system board.
** We recommend that you use an ATX 12V Specification 2.0-compliant power supply
unit (PSU) with a minimum of 350W power rating. This type has 24-pin and 4-pin
power plugs.
** If you intend to use a PSU with 20-pin and 4-pin power plugs, make sure that the 20-pin
power plug can provide at least 15A on +12V and the power supply unit has a minimum
power rating of 350W. The system may become unstable or may not boot up if the
power is inadequate.
(2) ATX 12V Power Connector (4-pin block) : ATX12V
This is a new defined 4-pins connector that usually comes with ATX Power Supply.
The ATX Power Supply which fully supports AM2 processor must including this
connector for support extra 12V voltage to maintain system power consumption.
Without this connector might cause system unstable because the power supply can not
provide sufficient current for system.
(3) PS/2 Mouse & PS/2 Keyboard Connector: KB
The connectors are for PS/2 keyboard and PS/2 Mouse.
(4) USB Port connector: USB1, UL1
The connectors are 4-pin connectors that connect USB devices to the system board.
(5) LAN Port connector: UL1
This connector is standard RJ45 connector for Network.
The USBLAN1 support 10M/100M data transfer rate.
ROW1 ROW2
Pin 1
24-Pin
PIN ROW 1 ROW2
1 3.3V 3.3V
2 3.3V -12V
3 GND GND
4 5V Soft Power On
5 GND GND
6 5V GND
7 GND GND
8 Power OK -5V
9 +5V (for Soft Logic) +5V
10 +12V +5V
11 +12V +5V
12 +3V GND
8
(6) Audio Line-In, Lin-Out, MIC Connector:
This Connector is 3 phones Jack for LINE-OUT, LINE-IN, and MIC
Line-out: (GREEN)
Line-in: (BLUE)
MIC: (PINK)
Audio input to sound chip
Microphone Connector
Audio output to speaker
SURROUND1
PS/2
Mouse
COM
VGA
LAN
Line-IN
Line-OUT
PS/2
Keyboard
USB1
MIC-IN
(7) Floppy drive Connector (34-pin block): FLOPPY
This connector supports the provided floppy drive ribbon cable. After connecting the
single plug end to motherboard, connect the two plugs at other end to the floppy drives.
FDD
Floppy Drive Connector
Pin 1
(8) Primary IDE Connector (40-pin block): IDE
This connector connects to the next set of Master and Slave hard disks. Follow the
same procedure described for the primary IDE connector. You may also configure two
hard disks to be both Masters using one ribbon cable on the primary IDE connector and
another ribbon cable on the secondary IDE connector.
Two hard disks can be connected to each connector. The first HDD is referred to
z
as the “Master” and the second HDD is referred to as the “Slave”.
For performance issues, we strongly suggest you don’t install a CD-ROM or
z
DVD-ROM drive on the same IDE channel as a hard disk. Otherwise, the system
performance on this channel may drop.
9
IDE1
IDE1
Primary IDE Connector
Pin 1
(9) Serial-ATA Port connector:
SATA1 / SATA2 / SATA3/ SATA4
• These connectors support the provided Serial ATA and Serial ATA2 IDE hard disk cable
to connecting the motherboard and serial ATA hard disk.
SATA4
SATA3
SATA2
SATA1
Serial-ATA1 & 2 Compatible Connectors
(10)
Serial COM Port: COM1
COM1 is the 9-pin connector. The On-board serial port can be disabled through BIOS
SETUP.
(11) VGA Connector (15-pin D-Sub) Connector: VGA
VGA is the 15-pin D-Subminiature female connector for display monitor.
10
3-2 Headers
(1) Line-Out/MIC Header for Front Panel (9-pin): AUDIO
This header is connected to Front Panel Line-out, MIC connector with cable.
GND
PRESENCE
SENSE1-RETURN
AUDIO
Line-Out, MIC Headers
Pin 1
2
AUD-MIC-L
AUD-MIC-R
AUD-Lineout2-R
KEY
SENSE2-RETUR
10
9
SENSE-SEND
AUD-Lineout2-L
(2) USB Port Headers (9-pin) : USB2 / USB3
These headers are used for connecting the additional USB port plug. By attaching an
option USB cable, your can be provided with two additional USB plugs affixed to the
back panel.
USB2
VCC
GND
-DATA
+DATA
USB3
OC
VCC
-DATA
+DATA
Pin 1
Pin 1
VCC
GND
-DATA
+DATA
USB Port Headers
VCC
-DATA
+DATA
(3) Speaker connector: SPEAK
This 4-pin connector connects to the case-mounted speaker. See the figure below.
(4) Power LED: PWR LED
The Power LED is light on while the system power is on. Connect the Power LED
from the system case to this pin.
(5) IDE Activity LED: HD LED
This connector connects to the hard disk activity indicator light on the case.
(6) Reset switch lead: RESET
This 2-pin connector connects to the case-mounted reset switch for rebooting your
computer without having to turn off your power switch. This is a preferred method of
rebooting in order to prolong the lift of the system’s power supply. See the figure
below.
OC
GND
GND
11
(7) Power switch: PWR BTN
This 2-pin connector connects to the case-mounted power switch to power ON/OFF the
system.
PWRBTN
PWR LED
PWRLED
Pin 1
Pin 1
JW FP
SPEAK
Pin 1
GND
VCC5
PWRLED
PWRBTN
SPKR
NC
GND
VCC5
VCC5
GND
HDDLE
NC
RSTSW
System Case Connections
RESET
HDLED
(8) FAN Power Headers: SYSFAN1, SYSFAN2 (3-pin), CPUFAN (4-pin)
These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the fan
manufacturer, the wire and plug may be different. The red wire should be positive, while the
black should be ground. Connect the fan’s plug to the board taking into consideration the
polarity of connector.
CPUFAN IN
GND
+12V
CPUFAN
1
SYSFAN1
FAN Power Headers
CPUFAN OUT
4
1
SYSFAN2
3
1
3
(9) CD Audio-In Headers (4-pin): CDIN
CDIN are the connectors for CD-Audio Input signal. Please connect it to CD-ROM
CD-Audio output connector.
CDIN
4 1
CD Audio-In Headers
12
(10) Parallel Port header (25-pin): PARALLEL
The On-board Parallel Port can be disabled through the BIOS SETUP. .
(11) SPDIF Out header: SPDIF Out
The SPDIF output is capable of providing digital audio to external speakers or compressed
AC3 data to an external Dolby digital decoder. Use this feature only when your stereo system
has digital input function.
Pin 1
PARALLEL Connector
SPDIF
HDMI_SPDIF_OUT GND
2
1
13
Chapter 4
DRIVER & FREE PROGRAM INSTALLATION
Check your package and there is A CD included. This CD consists of all DRIVERS you need
and some free application programs and utility programs. In addition, this CD also include an
auto detect software which can tell you which hardware is installed, and which DRIVERS
needed so that your system can function properly.
Supports WINDOWS 2000/ XP/ VISTA/ 7
Insert CD into your CD-ROM drive and the Menu should appear as below. If the menu does
not appear, double-click MY COMPUTER / double-click CD-ROM drive or click START /
click RUN / type X:\INTEL.EXE (assuming X is your CD-ROM drive).
The Intel P45 chipset driver only of Windows 2000/ Windows XP/ VISTA/ 7
Windows VISTA/ 7
14
Windows XP
Windows 2000
From MENU you may make as selections:
1. INF install Intel INF chipset system driver
2. VGA install VGA chipset driver
3. LAN install LAN Driver
4. SOUND install Audio driver
5. BROWSE CD to browse the contents of the CD
15
4-1 INF: Install Intel INF Chipset System Driver
Windows VISTA/ 7
Windows XP
Windows 2000
16
4-2 VGA: VGA Driver
Windows VISTA/ 7
Windows XP
Windows 2000
17
4-3 LAN: LAN Driver
Windows VISTA/ 7
Windows XP
Windows 2000
18
4-4 SOUND: Install Audio Driver
Windows VISTA/ 7
Windows XP
Windows 2000
19
4-5 HOW TO UPDATE BIOS
STEP 1. Prepare a boot floppy disc. (You may make one by click START click RUN type
SYS A: click OK)
STEP 2. Download upgrade tools and the latest BIOS files of the motherboard from official
website and then make a copy of it to your bootable floppy disk after
decompressing these files
STEP 3. Insert the disk into A: start your computer and then type in
“A:\xxxxxx.BAT”(xxxxxxx being the file name of the latest BIOS )
STEP 4. Type Enter to update and flash the BIOS. The system will restart automatically
when BIOS is upgraded.
4-6 Trouble Shooting
Problem Solution
No power to the system to the all power light
don’t illuminate, fan inside power supply doesn’t
turn on.
System inoperative. Keyboard lights are on ,
power indicator lights are lit, and hard drive is
spinning.
System doesn’t boot from hard disk drive, can be
booted from optical drive.
1. Make sure power cable is security plugged in.
2. Replace cable. 3. Contact technical support.
Using ever pressure on both ends of the DIMM ,
press down firmly until the module snaps into
places.
1. Check cable running from disk to disk
controller board. .Make sure both ends are
securely plugged in, check the drive type in the
standard CMOS setup. 2. Backing up the hard
drive is extremely important .All hard disks are
capable of breaking down at any time.
System only boots from optical drive .Hard disk
can be read and applications can be used but
booting from hard disk is impossible.
Screen message says “Invalid Configuration” or
“CMOS Failure”
Can not boot system after installing second hard
drive.
1. Back up date and applications files. 2.
Reformat the hard drive. Reinstall applications
and date using backup disks.
Review system ‘s equipment .Make sure correct
information on is in setup.
1. Set master /slave jumpers correctly. 2. Run
SETUP program and select correct drive types.
Call the drive manufacture for compatibility with
other drives.
20
Loading...