Intel H2000WP, H2000JF Quick Installation User's Manual
Thank you for buying an Intel® Server System. The following information will help you
assemble your Intel® Server System and install components.
If you are not familiar with ESD [Electrostatic Discharge] procedures used during
system integration, see the complete ESD procedures described in your Service Guide.
This guide and other supporting documents are located on the web at:
http://www.intel.com/support.
G54451-002
Intel® Server System H2000JF & H2000WP
Quick Installation User's Guide
Intel® Server System H2000JF & H2000WP
Quick Installation User's Guide
*
12 x 3.5" hard drive bay system as shown
( This page is intentionally left blank. )
i
Table of Contents
Reference .......................................................................................................................................... 12
Intel® Server Board S2600JF Component Layout............................................ 12
Intel® Server Board S2600WP Component Layout ........................................ 12
Front Panel Controls and Indicators........................................................................ 13
Cable Routing inside Server System H2000JF Node Tray
...................................... 13
Optional Accessories
............................................................................................................ 13
Cable Routing inside Server System H2000WP Node Tray
.................................. 14
Optional Accessories
............................................................................................................ 14
Intel® Server System RAID Options ........................................................................ 14
Intel® Server System RAID Options ........................................................................ 15
System Overview (Intel® Server System H2000JF Family)..........................................1
System Overview (Intel® Server System H2000WP Family) ......................................2
General Installation Process ..........................................................................................................3
Preparing the System ...................................................................................................... 3
Install/Remove the Power Supply Unit .................................................................. 3
Install/Remove Computer Node Tray ...................................................................... 3
Install/Remove Node Tray Air Duct .......................................................................... 4
Remove Processor Heat Sink(s) .................................................................................. 4
Install the Processor(s) .................................................................................................... 5
Install Processor Heat Sink(s) ...................................................................................... 6
Install Memory Modules .................................................................................................. 6
Install/Remove the Front Bezel .................................................................................. 7
Install Hard Drives .............................................................................................................. 7
Installing PCI Riser Assembly and Add-in Card on Riser Slot 1.................. 8
Install I/O Module Riser and Carrier Assembly on Riser Slot 2 .................. 9
Install Intel® RAID C600 Upgrade Key (optional)................................................ 9
Install Intel® Remote Management Module 4 (optional) ................................ 9
Remove the Top Cover ..................................................................................................10
Install Top Cover ................................................................................................................ 10
Software ................................................................................................................................10
Assembling the Server System with Server Chassis H2000 .................. 11
Removing a Node Tray from a Chassis.................................................................. 11
ii
Warning
Read all caution and safety
statements in this document
before performing any of the
instructions. Also see the Intel®
Server Board and Server Chassis
Safety Information document at:
http://www.intel.com/support/
motherboards/server/sb/cs-010770
.htm for complete safety information.
Warning
Installation and service
of this product to be
performed only by
qualified service personnel
to avoid risk of injury from
electrical shock or energy
hazard.
Caution
Observe normal ESD
[Electrostatic Discharge]
procedures during system
integration to avoid possible
damage to server board and/or
other components.
Tools Required
Anti-static
wrist strap
Phillips*
screwdriver
Flat Blade
screwdriver
Intel is a registered trademark of Intel Corporation or its subsidiaries in the United States and other countries. *Other names and brands may be claimed as the
property of others. Copyright © 2012, Intel Corporation. All rights reserved.
Thermal Operation and Configuration Requirements for Server System H2000WP
To keep the system operating within supported maximum thermal limits, the system must meet the following operating and
configuration guidelines:
• Ambient in-let temperature cannot exceed 35º C and should not remain at this maximum level for long periods of time.
Doing so may affect long term reliability of the system.
• The CPU-1 processor + CPU heatsink must be installed first. The CPU-2 heatsink must be installed at all times, with or
without a processor installed.
• Memory Slot population requirements:
NOTE: Specified memory slots either can be populated with a DIMM or supplied DIMM Blank. Memory population rules
apply when installing DIMMs.
▪ DIMM Population Rules on CPU-1
Install DIMMs in order: channels A1, B1, C1, D1, A2, B2, C2, and D2. Remove only DIMM blanks when populating
▪ DIMM Population on CPU-2
Install DIMMs in order: Channels E1, F1, G1, H1, E2, F2, G2, and H2. Only remove DIMM blanks when populating
• All hard drive bays must be populated. Hard drive carriers either can be populated with a hard drive or supplied
drive blank.
• The air duct must be installed at all times.
• The empty power supply bay must have the supplied filler blank installed at all times.
• The system top-cover must be installed at all times. Remove the top cover only when the system is in power-off state.
the slot with a DIMM.
the slot with a DIMM.
iii
Warning
Read all caution and safety
statements in this document
before performing any of the
instructions. Also see the Intel®
Server Board and Server Chassis
Safety Information document at:
http://www.intel.com/support/
motherboards/server/sb/cs-010770
.htm for complete safety information.
Warning
Installation and service
of this product to be
performed only by
qualified service personnel
to avoid risk of injury from
electrical shock or energy
hazard.
Caution
Observe normal ESD
[Electrostatic Discharge]
procedures during system
integration to avoid possible
damage to server board and/or
other components.
Tools Required
Anti-static
wrist strap
Phillips*
screwdriver
Flat Blade
screwdriver
Intel is a registered trademark of Intel Corporation or its subsidiaries in the United States and other countries. *Other names and brands may be claimed as the
property of others. Copyright © 2012, Intel Corporation. All rights reserved.
Thermal Operation and Configuration Requirements for Server System H2000JF
To keep the system operating within supported maximum thermal limits, the system must meet the following operating and
configuration guidelines:
• Ambient in-let temperature cannot exceed 35º C and should not remain at this maximum level for long periods of time.
Doing so may affect long term reliability of the system.
• The CPU-1 processor + CPU heatsink must be installed first. The CPU-2 heatsink must be installed at all times, with or
without a processor installed.
• Memory Slot population requirements:
NOTE: Specified memory slots either can be populated with a DIMM or supplied DIMM Blank. Memory population rules
apply when installing DIMMs.
▪ DIMM Population Rules on CPU-1
Install DIMMs in order; Channels A, B, C, and D. Only remove DIMM blanks when populating the slot with a DIMM.
▪ DIMM Population on CPU-2
Install DIMMs in order; Channels E, F, G, and H. Only remove DIMM blanks when populating the slot with a DIMM.
• All hard drive bays must be populated. Hard drive carriers either can be populated with a hard drive or supplied
drive blank.
• The air duct must be installed at all times.
• The empty power supply bay must have the supplied filler blank installed at all times.
• The system top-cover must be installed at all times. Remove the top cover only when the system is in power-off state.
1
System Overview
Intel® Server System H2000JF Family
System Features and Components
* 3.5" Hard Drive Bay system as shown
OPEN 1st
CLOSE 1st
OPEN 1st
CLOSE 1st
OPEN 1st
CLOSE 1st
OPEN 1st
CLOSE 1st
OPEN 1st
CLOSE 1st
OPEN 1st
CLOSE 1st
OPEN 1st
CLOSE 1st
OPEN 1st
CLOSE 1st
Compute
Node 3 Tray
Upper/Lower
Power Distribution
Boards
Common
Redundant
Power Supply
Compute
Node 1 Tray
Front Control Panel
HDD bays with
Hot Swap
Backplane
Compute
Node 4 Tray
Compute
Node 2 Tray
2
System Overview
Intel® Server System H2000WP Family
* 3.5" Hard Drive Bay system as shown
System Features and Components
Compute
Node 3 Tray
Upper/Lower
Power Distribution
Boards
Common
Redundant
Power Supply
Compute
Node 1 Tray
Front Control Panel
HDD bays with
Hot Swap
Backplane
Compute
Node 4 Tray
Compute
Node 2 Tray
Intel® Server System H2000JF and H2000WP Hard Drive Numbering Diagram
Intel® Server System H2000JF and H2000WP Compute Node Numbering Diagram - Rear View
Node 4
Node 2
Node 3
Node 1
PSU 2
PSU 1
12X3.5” Hard Drive Bay Option - Front View
NODE 4
NODE 2
NODE 3
NODE 1
Node3/HDD0
Node3/HDD2
Node1/HDD0
Node3/HDD1
Node1/HDD2
Node1/HDD1
Node4/HDD0
Node4/HDD2
Node2/HDD0
Node4/HDD1
Node2/HDD2
Node2/HDD1
Node3/HDD1
Node1/HDD2
Node1/HDD1
16X2.5” Hard Drive Bay Option - Front View
NODE 4
NODE 2
NODE 3
NODE 1
Node1/HDD2
Node1/HDD0
Node3/HDD2
Node3/HDD0
Node1/HDD3
Node1/HDD1
Node3/HDD3
Node3/HDD1
Node2/HDD2
Node2/HDD0
Node4/HDD2
Node4/HDD0
Node2/HDD3
Node2/HDD1
Node4/HDD3
Node4/HDD1
Loading...