Intel GA-8I945P PRO, GA-8I945P-G User Manual

GA-8I945P Pro/ GA-8I945P-G

Intel® Pentium® D / Pentium® 4 LGA775 Processor Motherboard

User's Manual

Rev. 1005

12ME-8I945PP-1005

* The WEEE marking on the product indicates this product must not be disposed of with user's other household waste

and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!

* The WEEE marking applies only in European Union's member states.

Apr. 18, 2005

GA-8I945P Pro/GA-8I945P-G

Motherboard

Apr. 18, 2005

GA-8I945P Pro/GA-8I945P-G

Motherboard

The trademarks mentioned in the manual are legally registered to their respective companies.

Notice

The written content provided with this product is the property of Gigabyte.

No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any

means without Gigabyte's prior written permission. Specifications and features are subject to

change without prior notice.

Product Manual Classification

In order to assist in the use of this product, Gigabyte has categorized the user manual in the

following:

 For quick installation, please refer to the "Hardware Installation Guide" included with the

product.

 For detailed product information and specifications, please carefully read the

"Product User Manual".

 For detailed information related to Gigabyte's unique features, please go to "Technology

Guide" section on Gigabyte's website to read or download the information you need.

For more product details, please click onto Gigabyte's website at www.gigabyte.com.tw

Table of Contents

GA-8I945P Pro/GA-8I945P-G Motherboard Layout ....................................................... 6

Block Diagram ................................................................................................................ 7

Chapter 1 Hardware Installation ..................................................................................... 9

1-1 Considerations Prior to Installation .................................................................... 9

1-2 Feature Summary .......................................................................................... 10

1-3 Installation of the CPU and Heatsink .............................................................. 12

1-3-1 Installation of the CPU ......................................................................................... 12

1-3-2 Installation of the Heatsink .................................................................................. 13

1-4 Installing/Removing Cool-Plus (Northbridge Cooling Fan) ......................... 14

1-5 Installation of Memory .................................................................................... 14

1-6 Installation of Expansion Cards ...................................................................... 16

1-7 I/O Back Panel Introduction ........................................................................... 17

1-8 Connectors Introduction .................................................................................. 18

Chapter 2 BIOS Setup ................................................................................................ 29

The Main Menu (For example: BIOS Ver. : GA-8I945P Pro F2a) ............................ 30

2-1 Standard CMOS Features ............................................................................. 32

2-2 Advanced BIOS Features .............................................................................. 34

2-3 Integrated Peripherals ..................................................................................... 36

2-4 Power Management Setup ............................................................................. 39

2-5 PnP/PCI Configurations ................................................................................. 41

2-6 PC Health Status ........................................................................................... 42

2-7 MB Intelligent Tweaker(M.I.T.) ....................................................................... 44

2-8 Select Language ........................................................................................ 47

2-9 Load Fail-Safe Defaults ................................................................................... 47

2-10 Load Optimized Defaults ................................................................................. 48

2-11 Set Supervisor/User Password ..................................................................... 48

2-12 Save & Exit Setup ......................................................................................... 49

2-13 Exit Without Saving ....................................................................................... 49

- 4 -

Chapter 3 Install Drivers ............................................................................................. 51

3-1 Install Chipset Drivers .................................................................................... 51

3-2 Software Applications ..................................................................................... 52

3-3 Driver CD Information .................................................................................... 52

3-4 Hardware Information ..................................................................................... 53

3-5 Contact Us ..................................................................................................... 53

Chapter 4 Appendix ................................................................................................... 55

4-1 Unique Software Utilities ................................................................................ 55

4-1-1 EasyTune 5 Introduction ..................................................................................... 56

4-1-2 Xpress Recovery2 Introduction ......................................................................... 57

4-1-3 Flash BIOS Method Introduction ........................................................................ 59

4-1-4 Serial ATA BIOS Setting Utility Introduction ................................................. 70

4-1-5 2- / 4- / 6- / 8- Channel Audio Function Introduction ...................................... 77

4-2 Troubleshooting ............................................................................................... 81

Only for GA-8I945P Pro.

- 5 -

Item Checklist

IDE Cable x 2 & FDD Cable x 1

Serial ATAII Cable x 2

Serial ATA Power Cable x 2

2 Ports USB 2.0 + 2 Ports 1394 Cable x 1

I/O Shield

* The items listed above are for reference only, and are subject to change without notice.

Optional Accessories

 8-Channel Audio Combo kit (Part Number: 12CR1-1SPAUD-21/R)

- 6 -

GA-8I945P Pro/GA-8I945P-G Motherboard Layout

COAXIAL

OPTICAL

KB_MS

COMA

R_USB

USB

AUDIO1

AUDIO2

LPT

LAN

Broadcom

5789

CD_IN

CODEC

IT8712

F_AUDIO

ATX_12V

LGA775

NB_FAN

PCIE_1

PCIE_2

Intel 945P

Main BIOS

Back

BIOS

CPU_FAN

PCIE_16

PCI1

PCI2

GA-8I945P (Pro)(-G)

DDRII1

DDRII2

ICH7R /

ICH7

TSB82AA2

SATAII0

SATAII2

DDRII3

SATAII3

IT8212

DDRII4

SATAII1

IDE3

ATX

PWR_FAN

FDD

IDE1

IDE2

SYS_FAN

RF_ID

Only for GA-8I945P Pro.

Only for GA-8I945P-G.

SPDIF_I

F_USB

GREEN_USB

- 7 -

PCI3

F1_1394

TSB81BA3

F2_1394

PWR_LED

(Optional)

BAT

F_PANEL

CLR_CMOS

Block Diagram

PCI-ECLK

(100MHz)

3 PCI

PCICLK

(33MHz)

PCI-ECLK

(100MHz)

2 PCI Express x1

x 1

PCI Express Bus

PCI Bus

TSB82AA2

TSB81BA3

3 IEEE1394b

PCI Express x16

RJ45

Broadcom

5789

x 1

IT8212

IDE RAID

IDE2/IDE3

LGA775

Processor

Interface

Intel

945P

Intel

ICH7R /

ICH7

CODEC

MIC

Line-Out

Side Speaker Out

Surround Speaker Out

Center/Subwoofer Speaker Out

CPUCLK+/-(133/200/266MHz)

Host

MCHCLK (133/200/266MHz)

Dual BIOS

8 USB

Ports

Line-In

SPDIF In

SPDIF Out

DDRII 667

Dual Channel Memory

66MHz 33MHz

14.318MHz 48MHz

4 SATA 3Gb/s

ATA33/66/100

IDE1 Channels

IT 8712

24MHz

33MHz

(Note)

/533/400MHz DIMM

LPT Port

COM Port

PS/2 KB/Mouse

Floppy

(Note) To use a DDRII 667 memory module on the motherboard, you must install an 800/1066MHz FSB

processor .

Only for GA-8I945P Pro.

Only for GA-8I945P-G.

- 8 -

Chapter 1 Hardware Installation

1-1 Considerations Prior to Installation

Preparing Your Computer

The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please follow the instructions below:

1. Please turn off the computer and unplug its power cord.

2. When handling the motherboard, avoid touching any metal leads or connectors.

3. It is best to wear an electrostatic discharge (ESD) cuff when handling electronic components (CPU, RAM).

4. Prior to installing the electronic components, please have these items on top of an antistatic pad or within a electrostatic shielding container.

5. Please verify that the power supply is switched off before unplugging the power supply connector from the motherboard.

Installation Notices

1. Prior to installation, please do not remove the stickers on the motherboard. These stickers are required for warranty validation.

2. Prior to the installation of the motherboard or any hardware, please first carefully read the information in the provided manual.

3. Before using the product, please verify that all cables and power connectors are connected.

4. To prevent damage to the motherboard, please do not allow screws to come in contact with the motherboard circuit or its components.

5. Please make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing.

6. Please do not place the computer system on an uneven surface.

7. Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user.

8. If you are uncertain about any installation steps or have a problem related to the use of the product, please consult a certified computer technician.

English

Instances of Non-Warranty

1. Damage due to natural disaster, accident or human cause.

2. Damage as a result of violating the conditions recommended in the user manual.

3. Damage due to improper installation.

4. Damage due to use of uncertified components.

5. Damage due to use exceeding the permitted parameters.

6. Product determined to be an unofficial Gigabyte product.

Hardware Installation- 9 -

English

1-2 Feature Summary

CPU  Supports Intel® Pentium® D / Pentium® 4 LGA775 CPU

 Supports 1066/800/533MHz FSB  L2 cache varies with CPU

Chipset  Northbridge: Intel® 945P Express Chipset

 Southbridge: Intel® ICH7R / ICH7  Supported on the Win 2000/XP operating systems

Memory  4 DDR II DIMM memory slots (supports up to 4GB memory)

 Supports 1.8V DDR II DIMM  Supports dual channel DDR II 667

(Note 3)

/533/400 DIMM

Slots  1 PCI Express x 16 slot

 2 PCI Express x 1 slot  3 PCI slots

IDE Connections  1 IDE connection (UDMA 33/ATA 66/ATA 100), allows connection of 2

IDE devices(IDE1)

- Supported on the Win 2000/XP operating systems

 2 IDE connection (UDMA 33/ATA 66/ATA 100/ATA 133), compatible with

RAID, allows connection of 4 IDE devices(IDE2,IDE3) FDD Connections  1 FDD connection, allows connection of 2 FDD devices Onboard SATA 3Gb/s  4 SATA 3Gb/s connections

 Supported on the Win 2000/XP operating systems

Peripherals  1 parallel port supporting Normal/EPP/ECP mode

 1 Serial port (COMA)  8 USB 2.0/1.1 ports (rear x 4, front x 4 via cable)  3 IEEE1394b ports (requires cable)  1 front audio connector  1 PS/2 keyboard port  1 PS/2 mouse port

Onboard LAN  Onboard Broadcom 5789 chip (10/100/1000 Mbit)

 1 RJ 45 port  Supported on the Win 2000/XP operating systems

(Note 1)

(Note 2)

(Note 1) For further CPU support information, please go to GIGABYTE's website. (Note 2) Due to standard PC architecture, a certain amount of memory is reserved for system usage and

therefore the actual memory size is less than the stated amount. For example, 4 GB of memory size will instead be shown as 3.xxGB memory during system startup.

(Note 3) To use a DDRII 667 memory module on the motherboard, you must install an 800/1066MHz FSB

processor .

Only for GA-8I945P Pro.

Only for GA-8I945P-G.

GA-8I945P (Pro)(-G) Motherboard - 10 -

Onboard Audio  ALC882 CODEC

 High Definition Audio  Supports 2 / 4 / 6 / 8 channel audio  Supports Line In ; Line Out (Front Speaker Out) ; MIC ; Surround Speaker Out

(Rear Speaker Out) ; Center/Subwoofer Speaker Out ;

Side Speaker Out connection

 SPDIF In connection  SPDIF Out connection (coaxial+optical)  CD In  Supported on the Win 2000/XP operating systems

On-Board SATA 3Gb/s  Onboard ICH7R chipset RAID  supports data striping (RAID 0) or mirroring (RAID 1) function or

striping + mirroring (RAID 0+1) or RAID 5 function

 supports data transfer rate of up 300 MB/s  supports a maximum of 4 SATA 3Gb/s connections  supported on the Win 2000/XP operating systems

On-Board IDE RAID  Onboard GigaRAID IT8212 chipset (IDE2, IDE3)  Supports disk striping (RAID 0) or disk mirroring (RAID 1) or

striping + mirroring (RAID 0 + RAID 1)

 Supports JBOD function  Supports concurrent dual ATA133 IDE controller operation  Supports ATAPI mode for HDD  Supports IDE bus master operation  Supports ATA133/RAID mode switch by BIOS  Displays status and error checking messages during boot-up  Mirroring supports automatic background rebuilds  Features LBA and Extended Interrupt 13 drive translation in

controller onboard BIOS I/O Control  IT8712 Hardware Monitor  System voltage detection

 CPU temperature detection  CPU / System / Power fan speed detection  CPU warning temperature  CPU / System / Power fan failure warning  CPU smart fan control

BIOS  Use of licensed AWARD BIOS

 Supports Q-Flash/Multilanguage /Dual BIOS

Additional Features  Supports @BIOS

 Supports EasyTune 5

Overclocking  Over Voltage via BIOS (CPU/DDR/PCIE/FSB)

 Over Clock via BIOS (CPU/DDR/PCIE)

Form Factor  ATX form factor; 30.5cm x 22.0cm

English

Only for GA-8I945P Pro.

Hardware Installation- 11 -

English

1-3 Installation of the CPU and Heatsink

Before installing the CPU, please comply with the following conditions:

1. Please make sure that the motherboard supports the CPU.

2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong direction, the CPU will not insert properly. If this occurs, please change the insert direction of the CPU.

3. Please add an even layer of heat sink paste between the CPU and heatsink.

4. Please make sure the heatsink is installed on the CPU prior to system use, otherwise overheating and permanent damage of the CPU may occur.

5. Please set the CPU host frequency in accordance with the processor specifications. It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the required standards for the peripherals. If you wish to set the frequency beyond the proper specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc.

HT functionality requirement content :

Enabling the functionality of Hyper-Threading Technology for your computer system requires all of the following platform components:

- CPU: An Intel® Pentium 4 Processor with HT Technology

- Chipset: An Intel® Chipset that supports HT Technology

- BIOS: A BIOS that supports HT Technology and has it enabled

- OS: An operation system that has optimizations for HT Technology

1-3-1 Installation of the CPU

Metal Lever

Fig. 1 Gently lift the metal lever located on the CPU socket to the upright position.

Fig. 2 Remove the plastic covering on the CPU socket.

Fig. 3 Notice the small gold colored triangle located on the edge of the CPU socket. Align the indented corner of the

CPU with the triangle and gently insert the CPU into position. (Grasping the CPU firmly between your thumb and forefinger, carefully place it into the socket in a straight and downwards motion. Avoid twisting or bending motions that might cause damage to the CPU during installation.)

GA-8I945P (Pro)(-G) Motherboard - 12 -

Fig. 4 Once the CPU is properly inserted, please replace the load plate and push the metal lever back into its original position.

1-3-2 Installation of the Heatsink

English

Male Push Pin

The top of Female Push Pin

Female Push Pin

Fig.1 Please apply an even layer of heatsink paste on the surface of the installed CPU.

Fig. 3 Place the heatsink atop the CPU and make sure the push pins aim to the pin hole on the motherboard.Pressing down the push pins diagonally.

Fig. 5 Please check the back of motherboard after installing. If the push pin is inserted as the picture, the installation is complete.

Fig. 2 (Turning the push pin along the direction of arrow is to remove the heatsink, on the contrary, is to install.) Please note the direction of arrow sign on the male push pin doesn't face inwards before installation. (This instruction is only for Intel boxed fan)

Fig. 4 Please make sure the Male and Female push pin are joined closely. (for detailed installation instructions, please refer to the heatsink installation section of the user manual)

Fig. 6 Finally, please attach the power connector of the heatsink to the CPU fan header located on the motherboard.

The heatsink may adhere to the CPU as a result of hardening of the heatsink paste.To prevent such an occurrence, it is suggested that either thermal tape rather than heat sink paste be used for heat dissipation or using extreme care when removing the heatsink.

Hardware Installation- 13 -

1-4 Installing/Removing Cool-Plus (Northbridge Cooling Fan)

English

Fig.1 To attach Cool-Plus to a heatsink, align the extensions on both sides with the grooves in the heatsink as shown. Firmly press down until it snaps into position.

Fig.3 Before proceeding, first check to make sure that the fan's power cable is disconnected. Then, while applying pressure to the top of the fan, carefully use a screwdriver to dislodge the extension on one side.

Exerting too much pressure on the fan during removal might cause the side extensions to break-off.

Fig.2 Once the fan is properly affixed onto the heatsink, plug the power cable into the NB_FAN connector.

1-5 Installation of Memory

Before installing the memory modules, please comply with the following conditions:

1. Please make sure that the memory used is supported by the motherboard. It is recommended that memory of similar capacity, specifications and brand be used.

2. Before installing or removing memory modules, please make sure that the computer power is switched off to prevent hardware damage.

3. Memory modules have a foolproof insertion design. A memory module can be installed in only one direction. If you are unable to insert the module, please switch the direction.

The motherboard supports DDR II memory modules, whereby BIOS will automatically detect memory capacity and specifications. Memory modules are designed so that they can be inserted only in one direction. The memory capacity used can differ with each slot.

Only for GA-8I945P Pro.

GA-8I945P (Pro)(-G) Motherboard - 14 -

Notch

DDR II

Fig.1 The DIMM socket has a notch, so the DIMM memory module can only fit in one direction. Insert the DIMM memory module vertically into the DIMM socket. Then push it down.

Fig.2 Close the plastic clip at both edges of the DIMM sockets to lock the DIMM module. Reverse the installation steps when you wish to remove the DIMM module.

Dual Channel Memory Configuration

GA-8I945P (Pro)(-G) supports the Dual Channel Technology. After operating the Dual Channel Technology, the bandwidth of Memory Bus will add double. GA-8I945P (Pro)(-G) includes 4 DIMM sockets, and each Channel has two DIMM

sockets as following:

Channel A : DDR II 1, DDR II 2 Channel B : DDR II 3, DDR II 4

If you want to operate the Dual Channel Technology, please note the following explanations due to the limitation of Intel chipset specifications.

1. Dual Channel mode will not be enabled if only one DDR II memory module is installed.

2. To enable Dual Channel mode with two or four memory modules (it is recommended to use memory modules of identical brand, size, chips, and speed), you must install them into DIMM sockets of the same color.

English

The following is a Dual Channel Memory configuration table: (DS: Double Side, SS: Single Side)

DDR II 1 DDR II 2 DDR II 3 DDR II 4

2 memory modules

4 memory modules

DS/SS X DS/SS X

X DS/SS X DS/SS

DS/SS DS/SS DS/SS DS/SS

Hardware Installation- 15 -

English

1-6 Installation of Expansion Cards

You can install your expansion card by following the steps outlined below:

1. Read the related expansion card's instruction document before install the expansion card into the computer.

2. Remove your computer's chassis cover, screws and slot bracket from the computer.

3. Press the expansion card firmly into expansion slot in motherboard.

4. Be sure the metal contacts on the card are indeed seated in the slot.

5. Replace the screw to secure the slot bracket of the expansion card.

6. Replace your computer's chassis cover.

7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.

8. Install related driver from the operating system.

Installing a PCI Express x 16 expansion card:

Please align the VGA card to the onboard PCI Express x 16 slot and press firmly down on the slot. Make sure your VGA card is locked by the latch at the end of the PCI Express x 16 slot. When you try uninstall the VGA card, please press the latch as the picture to the left shows to release the card.

GA-8I945P (Pro)(-G) Motherboard - 16 -

1-7 I/O Back Panel Introduction

PS/2 Keyboard and PS/2 Mouse Connector

To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the lower port (purple).

LPT (Parallel Port)

The parallel port allows connection of a printer, scanner and other peripheral devices.

COAXIAL (SPDIF Out)

The SPDIF coaxial output port is capable of providing digital audio to external speakers or

• compressed AC3 data to an external Dolby Digital Decoder via a coaxial cable.

OPTICAL (SPDIF Out)

The SPDIF optical output port is capable of providing digital audio to external speakers or com pressed AC3 data to an external Dolby Digital Decoder via an optical cable.

COM A (Serial Port)

Connects to serial-based mouse or data processing devices.

USB Port

Before you connect your device(s) into USB connector(s), please make sure your device(s) such as USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface. Also make sure your OS supports USB controller. If your OS does not support USB controller, please contact OS vendor for possible patch or driver upgrade. For more information please contact your OS or device(s) vendors.

LAN Port

The provided Internet connection is Gigabit Ethernet, providing data transfer speeds of 10/100/1000Mbps.

Line In

The default Line In jack. Devices like CD-ROM, walkman etc. can be connected to Line In jack.

Line Out (Front Speaker Out)

The default Line Out (Front Speaker Out) jack. Stereo speakers, earphone or front surround speakers can be connected to Line Out (Front Speaker Out) jack.

MIC In

The default MIC In jack. Microphone must be connected to MIC In jack.

Surround Speaker Out (Rear Speaker Out)

The default Surround Speaker Out (Rear Speaker Out) jack. Rear surround speakers can be connected to Surround Speaker Out (Rear Speaker Out) jack.

English

Hardware Installation- 17 -

English

Center/Subwoofer Speaker Out

The default Center/Subwoofer Speaker Out jack. Center/Subwoofer speakers can be connected to Center/Subwoofer Speaker Out jack.

Side Speaker Out

The default Side Speaker Out jack. Surround side speakers can be connected to Side Speaker Out jack.

In addition to the default speakers settings, the ~ audio jacks can be reconfigured to perform different functions via the audio software. Only microphones still MUST be connected to the de-

fault Mic In jack ( ) . Please refer to the 2-/4-/6-/8- channel audio setup steps for detailed software

configuration information.

1-8 Connectors Introduction

14615

1) ATX_12V

2) ATX (Power Connector)

3) CPU_FAN

4) SYS_FAN

5) PWR_FAN

6) NB_FAN

7) FDD

8) IDE1/IDE2/IDE3

9) SATAII0 / SATAII1 / SATAII2 / SATAII3

10) F_AUDIO

Only for GA-8I945P Pro.

GA-8I945P (Pro)(-G) Motherboard - 18 -

11) PWR_LED (Optional)

12) F_PANEL

13) CD_IN

14) SPDIF_I

15) F_USB/GREEN_USB

16) F1_1394/F2_1394

17) RF_ID

18) CI

19) CLR_CMOS

20) BAT

1/2) ATX_12V/ATX (Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, please make sure that all components and devices are properly installed. Align the power connector with its proper location on the motherboard and connect tightly. The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V power connector is not connected, the system will not start. Caution! Please use a power supply that is able to handle the system voltage requirements. It is recommended that a power supply that can withstand high power consumption be used (300W or greater). If a power supply is used that does not provide the required power, the result can lead to an unstable system or a system that is unable to start. If you use a 24-pin ATX power supply, please remove the small cover on the power connector

on the motherboard before plugging in the power cord ; Otherwise, please do not remove it.

Pin No. Definition

1 GND

2 GND

3 +12V

4 +12V

English

Pin No. Definition

1 3.3V

2 3.3V

3 GND

4 +5V

5 GND

6 +5V

7 GND

8 Power Good

9 5V SB(stand by +5V)

10 +12V

11 +12V

12 3.3V(Only for 24pins ATX)

13 3.3V

14 -12V

15 GND

16 PS_ON(soft On/Off)

17 GND

18 GND

19 GND

20 -5V

21 +5V

22 +5V

23 +5V

24 GND

Hardware Installation- 19 -

English

3/4/5) CPU_FAN / SYS_FAN / PWR_FAN (Cooler Fan Power Connector)

The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin (only for CPU_FAN) power connector and possesses a foolproof connection design. Most coolers are designed with color-coded power connector wires. A red power connector wire indicates a positive connection and requires a +12V power voltage. The black connector wire is the ground wire (GND). Please remember to connect the power to the cooler to prevent system overheating and failure. Caution! Please remember to connect the power to the CPU fan to prevent CPU overheating and failure.

Pin No. Definition

CPU_FAN

SYS_FAN/

1 GND

2 +12V

3 Sense

4 Speed Control

(Only for CPU_FAN)

PWR_FAN

6) NB_FAN (Chip Fan Connector)

If you installed wrong direction, the chip fan will not work. Sometimes will damage the chip fan. (Usually black cable is GND)

Only for GA-8I945P Pro.

GA-8I945P (Pro)(-G) Motherboard - 20 -

Pin No. Definition

1 +12V

2 GND

7) FDD (Floppy Connector)

The FDD connector is used to connect the FDD cable while the other end of the cable connects to the FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB. Please connect the red power connector wire to the pin1 position.

English

8) IDE1/IDE2/IDE3 (IDE Connector)

An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If you wish to connect two IDE devices, please set the jumper on one IDE device as Master and the other as Slave (for information on settings, please refer to the instructions located on the IDE device).

3940

Hardware Installation- 21 -

English

9) SATAII0/SATAII1/SATAII2/SATAII3 (SATA 3Gb/s Connector)

SATA 3Gb/s can provide up to 300MB/s transfer rate. Please refer to the BIOS setting for the Serial ATA II and install the proper driver in order to work properly.

Pin No. Definition

1 GND

2 TXP

3 TXN

4 GND

5RXN

6 RXP

7 GND

10) F_AUDIO (Front Audio Connector)

This connector supports either HD (High Definition) or AC97 front panel audio module. If you wish to use the front audio function, connect the front panel audio module to this connector. Check the pin assignments carefully while you connect the front panel audio module. Incorrect connection between the module and connector will make the audio device unable to work or even damage it. For optional front panel audio module, please contact your chassis manufacturer.

HD Audio: AC'97 Audio:

Pin No. Definition

1 MIC2_L

2 GND

3 MIC2_R

4 -ACZ_DET

5 Line2_R

6 FSENSE1

7 FAUDIO_JD

8 No Pin

9 LINE2_L

10 FSENSE2

Pin No. Definition

1 MIC

2 GND

3 MIC Power

4NC

5 Line Out (R)

6NC

7NC

8 No Pin

9 Line Out (L)

10 NC

By default, the audio driver is configured to support HD Audio. To connect an AC97 front panel audio module to this connector, please refer to the instructions on Page 78 about the software settings.

GA-8I945P (Pro)(-G) Motherboard - 22 -

11) PWR_LED (Optional)

PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode.

Pin No. Definition

1 MPD+

2 MPD-

3 MPD-

12) F_PANEL (Front Panel Jumper)

Please connect the power LED, PC speaker, reset switch and power switch etc of your chassis front panel to the F_PANEL connector according to the pin assignment below.

MSG-

HD-

Power Switch

PW+

RES-

PW-

RES+

Speaker Connector

SPEAK+

SPEAK-

20 19

Message LED/

Power/

Sleep LED

2 1

MSG+

HD+

English

Reset Switch

IDE Hard Disk Active LED

HD (IDE Hard Disk Active LED) (Blue) Pin 1: LED anode(+)

Pin 2: LED cathode(-)

SPEAK (Speaker Connector) (Amber) Pin 1: Power

Pin 2- Pin 3: NC

Pin 4: Data(-)

RES (Reset Switch) (Green) Open: Normal

Close: Reset Hardware System

PW (Power Switch) (Red) Open: Normal

Close: Power On/Off

MSG(Message LED/Power/Sleep LED) Pin 1: LED anode(+)

(Yellow) Pin 2: LED cathode(-)

NC ( Purple) NC

Hardware Installation- 23 -

English

13) CD_IN (CD IN)

Connect CD-ROM or DVD-ROM audio out to the connector.

Pin No. Definition

1 CD-L

2 GND

3 GND

4 CD-R

14) SPDIF_I (SPDIF In)

Use SPDIF IN feature only when your device has digital output function. Be careful with the polarity of the SPDIF_IN connector. Check the pin assignment carefully while you connect the SPDIF cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional SPDIF cable, please contact your local dealer.

GA-8I945P (Pro)(-G) Motherboard - 24 -

Pin No. Definition

1 Power

2 SPDIFI

3 GND

15) F_ USB/GREEN_USB (Front USB Connector)

Be careful with the polarity of the front USB connector. Check the pin assignments carefully while you connect the front USB cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional front USB cable, please contact your local dealer. The GREEN_USB connector provides no standby power when system is off and it does not support USB device to wake up from S3 mode. Users who wish to shut down the standby power

(note)

for their USB devices during system power-off can connect the devices to this connector via the optional front USB cable.

Pin No. Definition

2910

1 Power

2 Power

3 USB DX-

4 USB Dy-

5 USB DX+

6 USB Dy+

7 GND

8 GND

9 No Pin

10 NC

16) F1_1394/F2_1394 (IEEE 1394 Connector)

Serial interface standard set by Institute of Electrical and Electronics Engineers, which has features like high speed, highbandwidth and hot plug. Be careful with the polarity of the IEEE1394 connector. Check the pin assignment carefully while you connect the IEEE1394 cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional IEEE1394 cable, please contact your local dealer.IEEE1394b can approach the maximum speed to 800Mb/S, but the speed can be achieved only when you use particular IEEE1394b cable.

F2_1394

F1_1394

Only for GA-8I945P Pro.

2 1

Pin No. Definition

1 TPA2+

2 TPA2-

3 GND

4 GND

5 TPB2+

6 TPB2-

7 No Pin

8 Power

9 Power

10 GND

(Note) When the standby power is shut down, USB devices (example: optical mouses) will not light

on during system power-off.

Pin No. Definition

1 Power

2 Power

3 TPA0+

4 TPA0-

5 GND

6 GND

7 TPB0+

8 TPB0-

9 Power

10 Power

11 TPA1+

12 TPA1-

13 GND

14 No Pin

15 TPB1+

16 TPB1-

Hardware Installation- 25 -

English

17) RF_ID

This connector allows you to connect external devices to use extra function. Check the pin assignments before you connect the external device cable. Please contact your nearest dealer for the optional GIGABYTE external device.

Pin No. Definition

1 Power

2 RFID_RI-

3 RF_TXD

4 RF_RXD

5NC

6 GND

18) CI (Chassis Intrusion, Case Open)

This 2-pin connector allows your system to detect if the chassis cover is removed. You can check the "Case Opened" status in BIOS Setup.

GA-8I945P (Pro)(-G) Motherboard - 26 -

Pin No. Definition

1 Signal

2 GND

19) CLR_CMOS (Clear CMOS)

You may clear the CMOS data to its default values by this jumper. To clear CMOS, temporarily short 1-2 pin. Default doesn't include the "Shunter" to prevent from improper use this jumper.

Open: Normal

Short: Clear CMOS

20) BAT(Battery)

English

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type

recommended by the manufacturer.

Dispose of used batteries according to the manufacturer's

instructions.

If you want to erase CMOS...

1. Turn OFF the computer and unplug the power cord.

2. Take out the battery gently and put it aside for about 10

minutes (Or you can use a metal object to connect the

positive and negative pins in the battery holder to make

them short for one minute).

3. Re-install the battery.

4. Plug the power cord and turn ON the computer.

Hardware Installation- 27 -

+ 61 hidden pages