-001 First release of the Intel® Desktop Board DH57JG Product Guide January 2010
-002 Second release of the Intel® Desktop Board DH57JG Product Guide March 2010
-003 Third release of the Intel® Desktop Board DH57JG Product Guide July 2010
If an FCC declaration of conformity marking is present on the board, the following statement applies:
FCC Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
For questions related to the EMC performance of this product, contact:
Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124
1-800-628-8686
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications to the equipment not expressly approved by Intel Corporation could void the
user’s authority to operate the equipment.
Tested to comply with FCC standards for home or office use.
Canadian Department of Communications Compliance Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set
out in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numerique német pas de bruits radioélectriques dépassant les limites applicables aux
appareils numériques de la classe B prescrites dans le Réglement sur le broullage radioélectrique édicté par
le ministére des Communications du Canada.
Disclaimer
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL® PRODUCTS. NO LICENSE,
EXPRESS OR IMPLIED, BY ESTOPPEL OR
GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL’S TERMS AND CONDITIONS OF SALE FOR
SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR
IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR
WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT
OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Intel products are not intended
for use in medical, life saving, or life sustaining applications. Intel may make changes to specifications and
product descriptions at any time, without notice.
Intel Desktop Board DH57JG may contain design defects or errors known as errata which may cause the
product to deviate from published specifications. Current characterized errata are available on request.
Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing
your product order.
Copies of documents which have an ordering number and are referenced in this document, or other Intel
literature, may be obtained from Intel Corporation by going to the World Wide Web site at:
http://www.intel.com/ or by calling 1-800-548-4725.
This Product Guide gives information about board layout, component installation, BIOS
update, and regulatory requirements for Intel
®
Desktop Board DH57JG.
Intended Audience
The Product Guide is intended for technically qualified personnel. It is not intended for
general audiences.
Use Only for Intended Applications
All Intel Desktop Boards are evaluated as Information Technology Equipment (I.T.E.)
for use in personal computers (PC) for installation in homes, offices, schools, computer
rooms, and similar locations. The suitability of this product for other PC or embedded
non-PC applications or other environments, such as medical, industrial, alarm systems,
test equipment, etc. may not be supported without further evaluation by Intel.
Document Organization
The chapters in this Product Guide are arranged as follows:
1 Desktop Board Features: a summary of product features
2 Installing and Replacing Desktop Board Components: instructions on how to install
the Desktop Board and other hardware components
3 Updating the BIOS: instructions on how to update the BIOS
A Error Messages and Indicators: information about BIOS error messages and beep
codes
B Regulatory Compliance: describes the board’s adherence to safety standards and
EMC regulations and its product certifications
Conventions
The following conventions are used in this manual:
CAUTION
Cautions warn the user about how to prevent damage to hardware or loss of data.
NOTE
Notes call attention to important information.
iii
Intel Desktop Board DH57JG Product Guide
Terminology
The table below gives descriptions of some common terms used in the product guide.
• Discrete graphics support for PCI Express* 2.0 x16 add-in graphics
card
• 10-channel (7.1+2) Intel
using a Realtek* ALC889 audio codec
• 8-channel (7.1) Intel HD Audio via the HDMI port
One PCI Express 2.0 x16 add-in card connector
®
High Definition Audio (Intel® HD Audio)
continued
9
Intel Desktop Board DH57JG Product Guide
Table 1. Feature Summary (continued)
Peripheral
Interfaces
LAN Support Intel® 82578DC Gigabit (10/100/1000 Mb/s) Ethernet LAN controller
BIOS
Instantly Available
PC Technology
Hardware
Management
• Twelve USB 2.0 ports:
― Six ports are implemented with stacked back panel connectors
― Six front panel ports are implemented with three dual-port
internal headers
• Four internal Serial ATA (SATA) 3.0 Gb/s ports
• One external SATA (eSATA) 3.0 Gb/s port
• One serial port header
including an RJ-45 back panel connector with integrated status LEDs
• Intel
®
BIOS resident in an SPI Flash device
• Support for Advanced Configuration and Power Interface (ACPI),
Plug and Play, and SMBIOS
• Support for PCI Local Bus Specification Revision 2.3
• Support for PCI Express Base Specification Revision 2.0
• Suspend to RAM support
• Wake on PCI Express, LAN, front panel, serial, and USB ports
®
• Intel
Quiet System Technology (Intel® QST) implemented through
the Intel
®
Management Engine (Intel® ME) in the Intel H57 PCH
• Voltage sense to detect out of range power supply voltages
• Thermal sense to detect out of range thermal values
• Two fan headers using PWM control
• 4-pin headers for processor and chassis fans
• 4-wire and 3-wire (linear) fan speed control support for the
chassis fan
• Support for Platform Environmental Control Interface (PECI)
10
Supported Operating Systems
The Desktop Board supports the following operating systems:
• Microsoft Windows* 7 Ultimate 64-bit edition
• Microsoft Windows 7 Ultimate 32-bit edition
• Microsoft Windows 7 Professional 64-bit edition
• Microsoft Windows 7 Professional 32-bit edition
• Microsoft Windows 7 Home Premium 64-bit edition
• Microsoft Windows 7 Home Premium 32-bit edition
• Microsoft Windows 7 Starter 64-bit edition
• Microsoft Windows 7 Starter 32-bit edition
• Microsoft Windows 7 Home Basic 32-bit edition
• Microsoft Windows Vista* Ultimate 32-bit edition
• Microsoft Windows Vista Business 32-bit edition
• Microsoft Windows Vista Home Premium 32-bit edition
• Microsoft Windows Vista Home Basic 32-bit edition
• Microsoft Windows Vista Ultimate 64-bit edition
• Microsoft Windows Vista Business 64-bit edition
• Microsoft Windows Vista Home Premium 64-bit edition
• Microsoft Windows Vista Home Basic 64-bit edition
• Microsoft Windows* XP Media Center Edition 2005
• Microsoft Windows XP Professional
• Microsoft Windows XP Professional x64 Edition
• Microsoft Windows XP Home
Desktop Board Features
11
Intel Desktop Board DH57JG Product Guide
Desktop Board Components
Figure 1 shows the approximate location of the major components on Intel Desktop
Board DH57JG.
Figure 1. Intel Desktop Board DH57JG Components
12
Table 2. Intel Desktop Board DH57JG Components
Label Description
A Back panel connectors
B Front panel USB 2.0 header
C Front panel header
D Chassis intrusion header
E Alternate front panel power LED header
F BIOS configuration jumper block
G Serial ATA connectors (4)
H Front panel USB 2.0 header
I Front panel USB 2.0 header
J Chassis fan header
K Main power connector (2 x 12 pin)
L Processor fan header
M Standby power indicator LED
N Channel A DIMM 0 socket
O Channel B DIMM 0 socket
P Speaker
Q Processor socket
R Serial port header
S PCI Express 2.0 x16 add-in card connector
T S/PDIF header
U Battery
V Front panel audio header
W 12 V processor core voltage connector (2 x 2 pin)
Desktop Board Features
13
Intel Desktop Board DH57JG Product Guide
Online Support
For more information on Intel Desktop Board DH57JG consult the following online
resources:
Failure to use an appropriate power supply and/or not connecting the 12 V (2 x 2 pin)
power connector to the Desktop Board may result in damage to the board, or the
system may not function properly.
Intel Desktop Board DH57JG supports the Intel Core i5-600 series, Intel Core i3, and
Intel Pentium processors in an LGA1156 socket. Processors are not included with the
Desktop Board and must be purchased separately. The processor connects to the
Desktop Board through the LGA1156 socket.
For information on supported processors for Intel Desktop Board DH57JG, go to
http://processormatch.intel.com
.
14
Desktop Board Features
Intel® H57 Express Chipset
The Intel H57 Express Chipset, consisting of the Intel H57 Platform Controller Hub
(PCH), provides interfaces to the processor and the USB, SATA, LPC, audio, network,
display, and PCI Express x1 interfaces. The Intel H57 PCH is a centralized controller
for the board’s I/O paths.
Main Memory
NOTE
To be fully compliant with all applicable Intel® SDRAM memory specifications, the
board should be populated with DIMMs that support the Serial Presence Detect (SPD)
data structure. If your memory modules do not support SPD, you will see a
notification to this effect on the screen at power up. The BIOS will attempt to
configure the memory controller for normal operation.
The board has two DIMM sockets and supports the following memory features:
• Two independent memory channels with interleaved mode support
• Support for non-ECC, unbuffered, single-sided or double-sided DIMMs with x8
organization and single-sided DIMMs with x16 organization
• 8 GB maximum total system memory (with 2 Gb memory technology)
• Minimum total system memory: 512 MB using a 1 Gb x16 module
• Serial Presence Detect
• DDR3 1333 MHz and DDR3 1066 MHz SDRAM DIMMs
NOTE
32-bit operating systems are limited to a maximum of 4 GB of memory. These
operating systems will report less than 4 GB because of the memory used by
add-in graphics cards and other system resources.
15
Intel Desktop Board DH57JG Product Guide
Graphics Subsystem
The board supports system graphics through either Intel HD Graphics or a PCI Express
2.0 x16 add-in graphics card.
Integrated Graphics
The board supports integrated graphics through the Intel® Flexible Display Interface
(FDI) for processors with Intel HD Graphics.
Intel® HD Graphics
The Intel HD Graphics controller features the following:
• 3D Features
⎯ DirectX10* and OpenGL* 2.1 compliant
⎯ Shader Model 4.0
• Video
⎯ Hi-Definition content at up to 1080p resolution
⎯ Hardware accelerated MPEG-2, VC-1/WMV, and H.264/AVC High-Definition
video formats
®
⎯ Intel
• Dynamic Video Memory Technology (DVMT) 5.0 support including support of up to
1.7 GB Video Memory with a 4 GB and above system memory configuration
Clear Video HD Technology with advanced video processing
High-Definition Multimedia Interface* (HDMI*)
The HDMI port supports standard, enhanced, or high-definition video, plus multichannel digital audio on a single cable. It is compatible with all ATSC and DVB HDTV
standards and supports eight full range channels at 24-bit/96-kHz audio of lossless
audio formats such Dolby* TrueHD or DTS* HD Master Audio. The maximum
supported resolution is 1920 x 1200 at 60 Hz refresh (WUXGA). The HDMI port is
compliant with the HDMI 1.3 specification.
The HDMI port is enabled for the POST whenever a monitor is attached, regardless of
the DVI-I connector status.
Depending on the type of add-in card installed in the PCI Express x16 connector, the
HDMI port will behave as described in Table 3.
Table 3.
PCI Express x16 Connector Status HDMI Port Status
No add-in card installed Enabled
Non-video PCI Express x1, x4, or x8 add-in card installed Enabled
PCI Express x4, x8, or x16 graphics add-in card installed Disabled
HDMI Port Status Conditions
16
Desktop Board Features
Digital Visual Interface (DVI-I)
The DVI-I port supports both digital and analog DVI displays. The maximum
supported resolution is 1900 x 1200 (WUXGA). The DVI port is compliant with the
DVI 1.0 specification. The DVI analog output can be converted to VGA using a DVIVGA converter.
Depending on the type of add-in card installed in the PCI Express x16 connector, the
DVI port will behave as described in Table 4.
Table 4.
PCI Express x16 Connector Status
No add-in card installed Enabled Enabled
Non-video PCI Express x1, x4, or x8
add-in card installed
PCI Express x4, x8, or x16 graphics
add-in card installed
Note: DVI analog output can be converted to VGA with a DVI-VGA converter.
DVI Port Status Conditions
DVI Digital (DVI-D)
Port Status
Enabled Enabled
Disabled Disabled
DVI Analog (DVI-A)
Port Status
(Note)
VGA Displays
The DVI-I port supports VGA displays when a DVI-I to VGA converter is used. The
maximum supported resolution is 2048 x 1536 (QXGA).
The DVI-A port is enabled for the POST whenever a monitor is attached, regardless of
the HDMI connector status.
PCI Express* x16 Graphics
The Intel Core i5-600 series, Intel Core i3, and Intel Pentium processors in an
LGA1156 socket support discrete add-in graphics cards via the PCI Express 2.0 x16
add-in card connector. The board supports the following PCI Express speeds:
•PCI Express 2 frequency of 2.5 GHz which results in 5.0 Gb/s in each direction
(500 MB/s) per lane. The maximum theoretical bandwidth on the interface is
8 GB/s in each direction, simultaneously, when operating in x16 mode.
•PCI Express 1.1 frequency of 1.25 GHz resulting in 2.5 Gb/s each direction
(250 MB/s) per lane. The maximum theoretical bandwidth on the interface is
4 GB/s in each direction, simultaneously, when operating in x16 mode.
17
Intel Desktop Board DH57JG Product Guide
Audio Subsystem
The board supports Intel High Definition Audio through a Realtek ALC889 audio codec
as well as through the HDMI interface.
The Realtek ALC889-based audio subsystem provides the following features:
•Advanced jack sense for the back panel audio connectors that enables the audio
codec to recognize the device that is connected to an audio port
• Stereo input and output via back panel connectors
• Headphone and Mic in functions for front panel audio connectors
• 108 dB Signal-to-Noise ratio (SNR) playback (DAC) quality and 104 dB SNR
recording (ADC) quality
•Content protection for full-rate loss-less DVD Audio and Blu-ray Disc* audio
content playback (with selected versions of media player software)
The audio subsystem supports the following audio interfaces:
• 7.1 analog back panel audio connectors
• Optical S/PDIF-out back panel audio connector
• S/PDIF-out header with support for optical or coaxial S/PDIF output
• Front panel audio header with support for Intel HD Audio and AC ’97 Audio
Table 5 lists the supported functions of the front pa
nel and back pane
l audio jacks.
Table 5. Audio Jack Retasking Support
Audio
Jack
FP Green Default
FP Pink Default
BP Blue Default
BP Green Control
BP Pink Default
BP Black Default
BP Orange Default
Microphone
Head-
phones
panel
Front
Speakers Line In
Default
Side
Surround
Rear
Surround
Center/
Sub
18
LAN Subsystem
The LAN subsystem includes:
• Intel 82578DC Gigabit (10/100/1000 Mb/s) Ethernet LAN controller
• RJ-45 LAN connector with integrated status LEDs
Desktop Board Features
LAN software and drivers are available at http://downloadcenter.intel.com/
Two LEDs are built into the RJ-45 LAN connector located on the back panel (see
Figure 2). These LEDs indicate the status of the LAN as shown in Table 6.
Figure 2. LAN Connector LEDs
Table 6. LAN Connector LEDs
LED LED Color LED State Indicates
A (Link/Activity) Off LAN link is not established
Blinking LAN activity is occurring
B (Link Speed)
Green
On LAN link is established
N/A Off 10 Mb/s data rate
Green On 100 Mb/s data rate
Yellow On 1000 Mb/s data rate
.
USB 2.0 Support
The board supports up to twelve USB 2.0 ports provided by two EHCI host controllers
in the Intel H57 PCH that allow the use of EHCI-compatible drivers.
The port arrangement is as follows:
• Six ports via stacked back panel connectors
• Six front panel ports via three dual-port internal headers
USB 2.0 support requires both an operating system and drivers that fully support
USB 2.0 transfer rates.
19
Intel Desktop Board DH57JG Product Guide
Serial ATA Support
The board provides four internal SATA connectors and one back panel eSATA
connector which support one storage device per connector.
Expandability
Intel Desktop Board DH57JG provides one PCI Express 2.0 x16 connector for system
expansion.
Legacy I/O
The board’s Legacy I/O Controller provides the following legacy features:
• One serial port header
• Serial IRQ interface compatible with serialized IRQ support for PCI Conventional
bus systems
•Intelligent power management, including a programmable wake-up event interface
The BIOS Setup program provides configuration options for the Legacy I/O controller.
BIOS
The BIOS provides the Power-On Self-Test (POST), the BIOS Setup program, and the
PCI Express and SATA auto-configuration utilities. The BIOS is stored in the Serial
Peripheral Interface (SPI) Flash device.
The BIOS can be updated by following the instructions in Chapter 3 starting on
page 59.
Serial ATA Auto Configuration
If you install a SATA device (such as a hard drive) in your computer, the autoconfiguration utility in the BIOS automatically detects and configures the device for
your computer. You do not need to run the BIOS Setup program after installing a
SATA device. You can override the auto-configuration options by specifying manual
configuration in the BIOS Setup program.
PCI*/PCI Express Auto Configuration
If you install a PCI Express add-in card in your computer, the PCI Express autoconfiguration utility in the BIOS automatically detects and configures the resources
(IRQs, DMA channels, and I/O space) for that add-in card. You do not need to run the
BIOS Setup program after you install a PCI Express add-in card.
20
Desktop Board Features
Security Passwords
The BIOS includes security features that restrict whether the BIOS Setup program can
be accessed and who can boot the computer. A supervisor password and a user
password can be set for the BIOS Setup and for booting the computer, with the
following restrictions:
•The supervisor password gives unrestricted access to view and change all Setup
options. If only the supervisor password is set, pressing <Enter> at the password
prompt of Setup gives the user restricted access to Setup.
•If both the supervisor and user passwords are set, you must enter either the
supervisor password or the user password to access Setup. Setup options are then
available for viewing and changing depending on whether the supervisor or user
password was entered.
•Setting a user password restricts who can boot the computer. The password
prompt is displayed before the computer is booted. If only the supervisor
password is set, the computer boots without asking for a password. If both
passwords are set, you can enter either password to boot the computer.
For instructions on resetting the password, go to Clearing Passwords on page 52.
Hardware Management
The hardware management features of Intel Desktop Board DH57JG enable the board
to be compatible with the Wired for Management (WfM) specification. The board has
several hardware management features including the following:
• Fan speed monitoring and control
• Thermal and voltage monitoring
• Chassis intrusion detection
Hardware Monitoring and Fan Speed Control
The features of the hardware monitoring and fan speed control include:
•Intel Quiet System Technology, delivering acoustically-optimized thermal
management
•Thermal sensors in the processor and Intel H57 PCH, as well as near the processor
voltage regulators and system memory
NOTE
The minimum thermal reporting threshold for the Intel H57 PCH is 59 °C. The
PCH’s thermal sensor will display 59 °C until the temperature rises above this
point.
• Monitoring of system voltages to detect levels above or below acceptable values
• Thermally monitored closed-loop fan control for all fans that can adjust fan speed
as needed
21
Intel Desktop Board DH57JG Product Guide
Fan Monitoring
Fan monitoring can be observed via the BIOS Setup program, Intel® Desktop Utilities,
or third-party software.
Chassis Intrusion
The board supports a chassis security feature that detects if the chassis cover has
been removed. The security feature uses a mechanical switch on the chassis that can
be connected to the chassis intrusion header on the Desktop Board. See Figure 1 for
the location of the c
assis intrusion header.
h
Power Management
Power management is implemented at several levels, including software support
through the Advanced Configuration and Power Interface (ACPI) and the following
hardware support:
• Power connectors
• Fan headers
• LAN wake capabilities
• Instantly Available PC technology (Suspend to RAM)
• +5 V standby power indicator LED
• Wake from USB
• PCI Express WAKE# signal support
• Wake from serial port
Software Support
ACPI
ACPI gives the operating system direct control over the power management and Plug
and Play functions of a computer. The use of ACPI with the Desktop Board requires an
operating system that provides full ACPI support.
Hardware Support
Power Connectors
ATX12V-compliant power supplies can turn off the computer power through system
control. When an ACPI-enabled computer receives the correct command, the power
supply removes all non-standby voltages.
When resuming from an AC power failure, the computer returns to the power state it
was in before power was interrupted (either on or off). The computer’s response can
be set by using the Last Power State feature in the BIOS Setup program’s Boot menu.
The Desktop Board has two power connectors. See Figure 23 on page 50 for the
location of the power co
nnectors
.
22
Desktop Board Features
Fan Headers
The function/operation of the fans is as follows:
• The fans are on when the board is in the ACPI S0 or S1 state.
• The fans are off when the computer is in the ACPI S3, S4, or S5 state.
• Each fan header is wired to a tachometer input.
• All fan headers support closed-loop fan control that can adjust the fan speed or
switch the fan on or off as needed.
•All fan headers have a +12 V DC connection (up to 12 V DC when using 3-wire
chassis fans).
• All fan headers are controlled by Pulse Width Modulation.
• The chassis fan header supports linear fan control on 3-wire fans.
The Desktop Board has a 4-pin processor fan header and a 4-pin chassis fan header
compatible with 4-wire and 3-wire chassis fans.
LAN Wake Capabilities
CAUTION
For LAN wake capabilities, the 5 V standby line for the power supply must be capable
of delivering adequate +5 V standby current. Failure to provide adequate standby
current when using this feature can damage the power supply.
LAN wakeup capabilities enable remote wake-up of the computer through a network.
The LAN subsystem monitors network traffic and upon detecting a Magic Packet*
frame, it asserts a wake-up signal that powers up the computer.
Instantly Available PC Technology
CAUTION
For Instantly Available PC technology, the 5 V standby line for the power supply must
be capable of delivering adequate +5 V standby current. Failure to provide adequate
standby current when using this feature can damage the power supply and/or effect
ACPI S3 sleep state functionality.
Instantly Available PC technology enables the board to enter the ACPI S3 (Suspend-toRAM) sleep state. Instantly Available PC technology enables the board to enter the
ACPI S3 (Suspend-to-RAM) sleep-state. While in the S3 sleep-state, the computer will
appear to be off (the power supply is off and the front panel power LED will behave as
configured by the BIOS “S3 State Indicator” option). When signaled by a wake-up
device or event, the system quickly returns to its last known wake state. When
signaled by a wake-up device or event, the computer quickly returns to its last known
awake state.
23
Intel Desktop Board DH57JG Product Guide
The Desktop Board supports the PCI Bus Power Management Interface Specification.
Add-in cards that support this specification can participate in power management and
can be used to wake the computer.
The use of Instantly Available PC technology requires operating system support and
PCI 2.2 compliant add-in cards, PCI Express add-in cards, and drivers.
+5 V Standby Power Indicator LED
CAUTION
If the AC power has been switched off and the standby power indicator is still lit,
disconnect the power cord before installing or removing any devices connected to the
board. Failure to do so could damage the board and any attached devices.
The Desktop Board’s standby power indicator, shown in Figure 3, is lit when there is
standby power still present on the board even when the computer appears to be off.
For example, when this green LED is lit, standby power is still present at the memory
module sockets and the PCI Express connector.
Figure 3. Location of the Standby Power Indicator
24
Loading...
+ 54 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.