Intel BLKDG41TY, BOXDG41TY Product Manual

Intel® Desktop Board DG41TY
Product Guide

Order Number: E52797-001

Revision History

Revision Revision History Date

-001 First release of the Intel® Desktop Board DG41TY Product Guide October 2008

If an FCC declaration of conformity marking is present on the board, the following statement applies:

FCC Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

For questions related to the EMC performance of this product, contact:
Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124

1-800-628-8686
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications to the equipment not expressly approved by Intel Corporation could void the
user’s authority to operate the equipment.

Tested to comply with FCC standards for home or office use.

Canadian Department of Communications Compliance Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set
out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numerique német pas de bruits radioélectriques dépassant les limites applicables aux
appareils numériques de la classe B prescrites dans le Réglement sur le broullage radioélectrique édicté par
le ministére des Communications du Canada.

Disclaimer

INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL® PRODUCTS. NO LICENSE,
EXPRESS OR IMPLIED, BY ESTOPPEL OR
GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL’S TERMS AND CONDITIONS OF SALE FOR
SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR
IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR
WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT
OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Intel products are not intended
for use in medical, life saving, or life sustaining applications. Intel may make changes to specifications and
product descriptions at any time, without notice.

®

Desktop Board DG41TY may contain design defects or errors known as errata which may cause the

Intel
product to deviate from published specifications. Current characterized errata are available on request.

Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing
your product order.

Copies of documents which have an ordering number and are referenced in this document, or other Intel
literature, may be obtained from Intel Corporation by going to the World Wide Web site at:
http://www.intel.com/ or by calling 1-800-548-4725.

Intel, the Intel logo, Pentium, and Celeron are registered trademarks of Intel Corporation or its subsidiaries
in the United States and other countries.

* Other names and brands may be claimed as the property of others.
Copyright © 2008, Intel Corporation. All rights reserved.

OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS

Preface

This Product Guide gives information about board layout, component installation, BIOS
update, and regulatory requirements for Intel

®

Desktop Board DG41TY.

Intended Audience

The Product Guide is intended for technically qualified personnel. It is not intended for
general audiences.

Use Only for Intended Applications

All Intel Desktop Boards are evaluated as Information Technology Equipment (I.T.E.)
for use in personal computers (PC) for installation in homes, offices, schools, computer
rooms, and similar locations. The suitability of this product for other PC or embedded
non-PC applications or other environments, such as medical, industrial, alarm systems,
test equipment, etc. may not be supported without further evaluation by Intel.

Document Organization

The chapters in this Product Guide are arranged as follows:
1 Desktop Board Features: a summary of product features
2 Installing and Replacing Desktop Board Components: instructions on how to install

the Desktop Board and other hardware components
3 Updating the BIOS: instructions on how to update the BIOS
A Error Messages and Indicators: information about BIOS error messages and beep

codes
B Regulatory Compliance: information about safety standards, EMC regulations, and

product certifications

iii

Intel Desktop Board DG41TY Product Guide

Conventions

The following conventions are used in this manual:

CAUTION

Cautions warn the user about how to prevent damage to hardware or loss of data.

NOTE

Notes call attention to important information.

Terminology

The table below gives descriptions of some common terms used in the product guide.

Term Description

GB Gigabyte (1,073,741,824 bytes)
GHz Gigahertz (one billion hertz)
KB Kilobyte (1024 bytes)
MB Megabyte (1,048,576 bytes)
Mbit Megabit (1,048,576 bits)
MHz Megahertz (one million hertz)

iv

Contents

1 Desktop Board Features

Supported Operating Systems..............................................................................10

Desktop Board Components.................................................................................11

Processor..........................................................................................................13

Main Memory.....................................................................................................13

®

Intel

G41 Express Chipset .................................................................................14

®

Intel

G41 Graphics Subsystem....................................................................15

Intel® GMA X4500 Graphics Controller (Intel

Audio Subsystem ...............................................................................................16

Legacy Input/Output (I/O) Controller....................................................................17

LAN Subsystem .................................................................................................17

RJ-45 LAN Connector LEDs...........................................................................17

Hi-Speed USB 2.0 Support ..................................................................................18

Enhanced IDE Interface ......................................................................................18

Serial ATA.........................................................................................................18

Expandability.....................................................................................................19

BIOS................................................................................................................19

Serial ATA and IDE Auto Configuration...........................................................19

PCI* and PCI Express* Auto Configuration .....................................................19

Security Passwords.....................................................................................20

Hardware Management Features ..........................................................................20

Hardware Monitoring and Fan Speed Control ..................................................21

Chassis Intrusion........................................................................................21

Power Management Features ...............................................................................21

ACPI.........................................................................................................21

Hardware Support ......................................................................................22

Power Connectors ...............................................................................22

Fan Headers .......................................................................................22

LAN Wake Capabilities..........................................................................22

Instantly Available PC Technology..........................................................23

+5 V Standby Power Indicator LED ........................................................23

Wake from USB ..................................................................................24

PME# Signal Wake-up Support..............................................................24

WAKE# Signal Wake-up Support ...........................................................24

ENERGY STAR* Capable ..............................................................................24

Speaker............................................................................................................24

Battery.............................................................................................................24

Real-Time Clock.................................................................................................25

®

GMA X4500) .......................15

2 Installing and Replacing Desktop Board Components

Before You Begin ...............................................................................................27

Installation Precautions.......................................................................................28

Prevent Power Supply Overload ....................................................................28

Observe Safety and Regulatory Requirements.................................................28

Installing the I/O Shield ......................................................................................29

Installing and Removing the Desktop Board ...........................................................30

Installing and Removing a Processor.....................................................................31

v

Intel Desktop Board DG41TY Product Guide

Installing a Processor ..................................................................................31

Installing the Processor Fan Heat Sink ...........................................................34

Connecting the Processor Fan Heat Sink Cable................................................35

Removing the Processor ..............................................................................36

Installing and Removing Memory..........................................................................36

Installing DIMMs ........................................................................................37

Removing DIMMs........................................................................................39

Installing and Removing a PCI Express x16 Card ....................................................39

Installing a PCI Express x16 Card .................................................................40

Removing the PCI Express x16 Card..............................................................41

Connecting the Diskette Drive Cable .....................................................................42

Connecting the IDE Cable....................................................................................43

Connecting the Serial ATA (SATA) Cables ..............................................................44

Connecting to the Internal Headers and Connectors ................................................45

S/PDIF Connector.......................................................................................46

Front Panel Audio Header ............................................................................46

Serial Port Header ......................................................................................47

HD Audio Link Header .................................................................................47

Chassis Intrusion Header.............................................................................48

Front Panel Header .....................................................................................48

Alternate Front Panel Power LED Header........................................................49

USB 2.0 Headers ........................................................................................49

Connecting to the Back Panel Audio Connectors......................................................50

Connecting Chassis Fan and Power Supply Cables...................................................51

Connecting Chassis Fan Cables.....................................................................51

Connecting Supply Power Cables ..................................................................52

Setting the BIOS Configuration Jumper .................................................................53

Clearing Passwords ............................................................................................54

Replacing the Battery .........................................................................................55

3 Updating the BIOS

Updating the BIOS with the Intel
Updating the BIOS with the ISO Image BIOS Update File or the Iflash Memory Update

Utility .........................................................................................................62

Obtaining the BIOS Update File ....................................................................62

Updating the BIOS with the ISO Image BIOS Update File .................................62

Updating the BIOS with the Iflash Memory Update Utility .................................63

Recovering the BIOS...................................................................................64

®

Express BIOS Update Utility.................................61

A Error Messages and Indicators

BIOS Beep Codes...............................................................................................65

BIOS Error Messages..........................................................................................65

B Regulatory Compliance

Safety Standards ...............................................................................................67

Place Battery Marking .................................................................................67

European Union Declaration of Conformity Statement..............................................68

Product Ecology Statements ................................................................................69

Recycling Considerations .............................................................................69

Lead-Free Desktop Board.............................................................................71

EMC Regulations ................................................................................................73

Ensure Electromagnetic Compatibility (EMC) Compliance..................................74

vi

Contents

Product Certifications..........................................................................................75

Board-Level Certification Markings ................................................................75

Chassis and Component Certifications............................................................76

Figures

1. Intel Desktop Board DG41TY Components........................................................11

2. LAN Connector LEDs .....................................................................................17

3. Location of the Standby Power Indicator ..........................................................23

4. Installing the I/O Shield ................................................................................29

5. Intel Desktop Board DG41TY Mounting Screw Hole Locations ..............................30

6. Lift the Socket Lever.....................................................................................31

7. Lift the Load Plate.........................................................................................32

8. Remove the Protective Socket Cover ...............................................................32

9. Remove the Processor from the Protective Processor Cover ................................33

10. Install the Processor .....................................................................................33

11. Close the Load Plate .....................................................................................34

12. Connecting the Processor Fan Heat Sink Cable to the Processor Fan Header..........35

13. Dual Channel Memory Configuration Example ...................................................36

14. Use DDR2 DIMMs .........................................................................................37

15. Installing a DIMM .........................................................................................38

16. Installing a PCI Express x16 Card ...................................................................40

17. Removing a PCI Express x16 Card ..................................................................41

18. Connecting the Diskette Drive Cable................................................................42

19. Connecting the IDE Cable ..............................................................................43

20. Connecting a Serial ATA Cable........................................................................44

21. Internal Headers and Connectors....................................................................45

22. Back Panel Audio Connectors .........................................................................50

23. Location of the Chassis Fan Headers................................................................51

24. Connecting Power Supply Cables ....................................................................52

25. Location of the BIOS Configuration Jumper Block ..............................................53

26. Removing the Battery ...................................................................................59

Tables

1. Feature Summary.......................................................................................... 9

2. Intel Desktop Board DG41TY Components........................................................12

3. Audio Jack Retasking Support.........................................................................16

4. LAN Connector LEDs .....................................................................................18

5. S/PDIF Connector .........................................................................................46

6. Jumper Settings for the Front Panel Audio Select Jumper Block ...........................46

7. Front Panel Audio Signal Names for Intel HD Audio............................................46

8. Front Panel Audio Header Signal Names for AC’97 Audio ....................................47

9. Serial Port Header Signal Names.....................................................................47

10. HD Audio Link Header Signal Names ...............................................................47

11. Chassis Intrusion Header...............................................................................48

12. Front Panel Header .......................................................................................48

13. Alternate Front Panel Power LED Header..........................................................49

14. USB 2.0 Header Signal Names........................................................................49

15. Jumper Settings for the BIOS Setup Program Modes..........................................53

16. Beep Codes .................................................................................................65

17. BIOS Error Messages ....................................................................................65

18. Safety Standards..........................................................................................67

vii

Intel Desktop Board DG41TY Product Guide

19. Lead-Free Board Markings .............................................................................72

20. EMC Regulations...........................................................................................73

21. Product Certification Markings ........................................................................75

viii

1 Desktop Board Features

This chapter briefly describes the features of Intel® Desktop Board DG41TY. Table 1
summarizes the major features of the Desktop Board.

Table 1. Feature Summary

Form Factor

Processor Support for an Intel® processor in the LGA775 package
Main Memory

Chipset Intel® G41 Express Chipset consisting of:

Graphics

Audio

LAN Support
Expansion

Capabilities

Peripheral
Interfaces

microATX (218.44 millimeters [8.60 inches] x 243.84 millimeters
[9.60 inches])

• Two 240-pin, DDR2 1.8 V SDRAM Dual Inline Memory Module

(DIMM) sockets

• 800/667 MHz single or dual channel DDR2 SDRAM interface

• Support for up to 4 GB of system memory

• Intel G41 Express Chipset Graphics and Memory Controller Hub

(GMCH) with Intel® Graphics Media Accelerator X4500 (Intel® GMA
X4500)

• Intel

• Intel G41 Express Chipset Graphics and Memory Controller Hub

• Integrated graphics output for VGA and DVI-D

• One PCI Express* x16 connector supporting PCI Express graphics

• 5.1 + 2-channel onboard audio subsystem, featuring:

• Onboard S/PDIF connector

• One PCI Express x16 connector

• One PCI Express x1 connector

• Two PCI* bus connectors

• Up to eight USB 2.0 ports

• Four Serial ATA (SATA) channels (3.0 Gb/s) via the ICH7

• One IDE interface with ATA-66/100 support (two devices)

• One diskette drive interface

• One VGA connector

• One DVI-D connector

• One serial port header

• PS/2* keyboard and mouse ports

®

82801G I/O Controller Hub (ICH7)

(GMCH)

cards

― Realtek* ALC888VC audio codec
― Support for Intel

Realtek 8111D Gigabit Ethernet Controller

― Four ports routed to the back panel
― Four ports routed to two USB headers

®

High Definition Audio and AC ’97 Audio

continued

9

Intel Desktop Board DG41TY Product Guide

Table 1. Feature Summary (continued)

BIOS

Power Management

Hardware Monitor

• Intel

• 8 Mbit symmetrical flash memory device

• Support for SMBIOS

• Intel

• Intel

• Support for Advanced Configuration and Power Interface (ACPI)

• Suspend to RAM (STR)

• Wake on USB, PCI Express, LAN, and front panel

• ENERGY STAR* capable

• Voltage sense to detect out of range power supply voltages

• Thermal sense to detect out of range temperatures

• Three fan headers

• Three fan sense inputs to monitor fan speed

®

Platform Innovation Framework for extensible firmware

interface

®

Rapid BIOS Boot

®

Express BIOS Update

Related Links:

For more information about Intel Desktop Board DG41TY, including the Technical
Product Specification (TPS), BIOS updates, and device drivers, go to:

http://support.intel.com/support/motherboards/desktop/

Supported Operating Systems

The Desktop Board supports the following operating systems:

• Microsoft Windows Vista* Ultimate

• Microsoft Windows Vista Enterprise

• Microsoft Windows Vista Business

• Microsoft Windows Vista Home Premium

• Microsoft Windows Vista Home Basic

• Microsoft Windows Vista Ultimate 64-bit edition

• Microsoft Windows Vista Enterprise 64-bit edition

• Microsoft Windows Vista Business 64-bit edition

• Microsoft Windows Vista Home Premium 64-bit edition

• Microsoft Windows Vista Home Basic 64-bit edition

• Microsoft Windows* XP Media Center Edition 2005

• Microsoft Windows XP Professional

• Microsoft Windows XP Professional x64 Edition

• Microsoft Windows XP Home

10

Desktop Board Features

Desktop Board Components

Figure 1 shows the approximate location of the major components on Intel Desktop
Board DG41TY.

Figure 1. Intel Desktop Board DG41TY Components

11

Intel Desktop Board DG41TY Product Guide

Table 2. Intel Desktop Board DG41TY Component s

Label Description

A PCI bus connector 2
B PCI bus connector 1
C PCI Express x1 connector
D PCI Express x16 connector
E Rear chassis fan header (3-pin)
F Back panel connectors
G 12 V processor core voltage connector (2 x 2 pin)
H Processor socket
I Processor fan header (4-pin)
J DDR2 Channel A DIMM 0 socket
K DDR2 Channel B DIMM 0 socket
L Main power connector (2 x 12 pin)
M IDE connector
N Battery
O Front chassis fan header (3-pin)
P Serial ATA connectors (4)
Q Chassis intrusion header
R Front panel header
S HD Audio Link header
T Alternate front panel power LED header
U BIOS configuration jumper block
V High-speed USB 2.0 headers (2)
WW Speaker
X Diskette drive connector
Y Serial port header
Z S/PDIF connector
AA Front panel audio header
BB Front panel audio select jumper block

12

Desktop Board Features

Related Links:

Go to the following links for more information about:

• Intel Desktop Board DG41TY

• Supported processors

• Audio software and utilities

• LAN software and drivers

http://www.intel.com/design/motherbd
http://support.intel.com/support/motherboards/desktop

http://processormatch.intel.com
http://www.intel.com/design/motherbd
http://www.intel.com/design/motherbd

Processor

CAUTION

Failure to use an appropriate power supply and/or not connecting the 12 V (2 x 2 pin)
power connector to the Desktop Board may result in damage to the board, or the
system may not function properly.

Intel Desktop Board DG41TY supports an Intel processor in the LGA775 package.
Processors are not included with the Desktop Board and must be purchased
separately. The processor connects to the Desktop Board through the LGA775 socket.

Related Links:

Go to the following page or link for more information about:

• Instructions on installing or upgrading the processor, page 31 in Chapter 2

• Supported

http://www.intel.com/go/findCPU

processors for Intel Desktop Board DG41TY,

Main Memory

NOTE

To be fully compliant with all applicable Intel ® SDRAM memory specifications, the
board should be populated with DIMMs that support the Serial Presence Detect (SPD)
data structure. If your memory modules do not support SPD, you will see a
notification to this effect on the screen at power up. The BIOS will attempt to
configure the memory controller for normal operation.

13

Intel Desktop Board DG41TY Product Guide

The Desktop Board supports the memory configurations listed below:

• Four 240-pin Double Data Rate 2 (DDR2) SDRAM Dual Inline Memory Module

(DIMM) connectors with gold-plated contacts

• Support for:

⎯ Non-ECC, 1.8 V, DDR2 800/667 MHz memory
⎯ Serial Presence Detect (SPD) memory only
⎯ Unbuffered, non-registered single- or double-sided DIMMs
⎯ Memory configurations listed below:

• Up to 2.0 GB utilizing 256 Mb technology

• Up to 4.0 GB utilizing 512 Mb or 1 Gb technology

• A minimum of 512 MB of total memory is required

NOTE

System resources and hardware (such as PCI Express) require physical memory
address locations that can reduce available addressable system memory. This could
result in a reduction of as much as 1 GB or more of physical addressable memory
being available to the operating system and applications, depending on the system
configuration and operating system.

Go to the following locations for more information about:

• SDRAM specifications, http://intel.com/technology/memory/

• Installing memory, page 36 in Chapter 2

• Tested memory, http://cmtlabs.com/mbsearch.asp

Intel® G41 Express Chipset

The Intel G41 Express Chipset consists of the following devices:

• Intel G41 Express Chipset Graphics and Memory Controller Hub (GMCH) with Direct

Media Interface (DMI)

• Intel 82801G I/O Controller Hub (ICH7) with DMI
The GMCH component provides interfaces to the processor, memory, PCI Express, and

the DMI interconnect. The component also provides integrated graphics capabilities
supporting 3D, 2D, and display capabilities. The ICH7 is a centralized controller for
the board’s I/O paths.

Related Links:

Go to the following link for more information about the Intel G31 Express Chipset:

http://developer.intel.com/products/chipsets/index.htm

14

Intel® G41 Graphics Subsystem

Desktop Board Features

The Intel G41 Express Chipset supports two separate, mutually exclusive graphics
options. Either the integrated Intel
GMA X4500) graphics controller is used or a PCI Express x16 add-in card can be used.
When a PCI Express x16 add-in card is installed, the Intel GMA X4500 graphics
controller is disabled.

®

Graphics Media Accelerator X4500 (Intel®

Intel® GMA X4500 Graphics Controller (Intel® GMA X4500)

The Intel GMA X4500 graphics controller has the following features:

• Advanced graphics performance, including:

⎯ DirectX10.0* and OpenGL* 2.0 compliant

⎯ Shader Model 4.0 support

• Enhanced video playback support, including:

⎯ Support for playback of Blu-ray Disc* technology DVDs

o Microsoft Windows Vista* only
o Hardware acceleration supported for MPEG-2 only

⎯ Software DVD at 30 fps full screen

⎯ Dynamic Video Memory Technology (DVMT) 5.0

• Advanced display support, including:

⎯ DVI specification 1.0 compliant

⎯ Dual independent display support via the VGA and DVI-D back panel connectors

⎯ High Definition Content Protection (HDCP) version 1.1 support

⎯ DDC2B compliant interface with Advanced Digital Display 2 card or Media

Expansion Card (ADD2/MEC); support for TV-out/TV-in and DVI digital display
connections

⎯ Support for all HD display resolutions including 720p, 1080i, and 1080p

⎯ Support for digital and analog displays up to 2048 x 1536 at 75 Hz refresh rate

(QXGA); also supports 1920 x 1080 resolution for full High Definition video
playback quality

15

Intel Desktop Board DG41TY Product Guide

Audio Subsystem

The onboard audio subsystem consists of the following:

®

• Intel

• Realtek ALC888VC audio codec

• Back panel audio connectors

• Onboard audio headers/connectors:

The audio subsystem supports the following features:

• A signal-to-noise (S/N) ratio of 95 dB

• Independent multi-streaming 5.1 audio (using the back panel audio connectors)

ICH7

⎯ Front panel audio header supporting both Intel High Definition Audio and AC ’97

Audio

⎯ HD Audio Link header

⎯ S/PDIF connector

and 2-channel stereo (using the front panel audio header)
Table 3 lists the supported functions for the front pa

nel and back panel audio jacks.

Table 3. Audio Jack Ret asking Support

Jack Mic Line out Headphones Line in

Front Panel

Green No Yes Yes No No No
Pink Yes No No No No No

Back Panel

Blue No No No Yes Yes No
Green No Yes Yes No No No
Pink Yes No No No No Yes

Rear
Surround

Center/
Subwoofer

Related Links:

Go to the following link or pages for more information about:

• Audio drivers and utilities http://support.intel.com/support/motherboards/desktop/

• The location of the back panel audio connectors, Figure 22 on page 50

16

Desktop Board Features

Legacy Input/Output (I/O) Controller

The Winbond 83627DHG-P legacy I/O controller features the following:

• Low pin count (LPC) interface

• One serial port interface via an onboard header

• Serial IRQ interface compatible with serialized IRQ support for PCI systems

• Intelligent power management, including a programmable wake up event interface

• PCI power management support

LAN Subsystem

The LAN subsystem includes:

• Intel ICH7

• Realtek 8111D Gigabit Ethernet Controller for operation at 10/100/1000 Mb/s

• RJ-45 LAN connector with integrated status LEDs

The subsystem features:

• CSMA/CD protocol engine

• LAN connect interface between ICH7 and the LAN controller

• PCI bus power management

Related Links:

Go to the following link for information about LAN software and drivers:

http://support.intel.com/support/motherboards/desktop

RJ-45 LAN Connector LEDs

Two LEDs are built into the RJ-45 LAN connector located on the back panel (see
Figure 2). These LEDs indicate th

Figure 2. LAN Connector LEDs

e status of the LAN.

17

Intel Desktop Board DG41TY Product Guide

Table 4 describes the LED states when the board is powered up and the LAN
subsystem is operating.

Table 4. LAN Connector LEDs

LED LED Color LED State Indicates

A Off LAN link is not established

Blinking LAN activity is occurring
B

Green

On LAN link is established

N/A Off 10 Mb/s data rate
Green On 100 Mb/s data rate
Yellow On 1000 Mb/s data rate

Hi-Speed USB 2.0 Support

The Desktop Board supports up to eight USB 2.0 ports (four ports routed to the back
panel and four ports routed to two internal headers) via the ICH7. USB 2.0 ports are
backward compatible with USB 1.1 devices. USB 1.1 devices will function normally at
USB 1.1 speeds.

USB 2.0 support requires both an operating system and drivers that fully support
USB 2.0 transfer rates. Disabling Hi-Speed USB in the BIOS reverts all USB 2.0 ports
to USB 1.1 operation. This may be required to accommodate operating systems that
do not support USB 2.0.

Enhanced IDE Interface

The board’s IDE interface handles the exchange of information between the processor
and peripheral devices such as hard disk drives and CD-ROM drives. The interface
supports:

• Up to two IDE devices (such as hard drives)

• ATAPI-style devices (such as CD-ROM drives)

• Older PIO Mode devices

• Ultra DMA-33 and ATA-66/100 protocols

Serial ATA

The Desktop Board supports four Serial ATA channels (3.0 Gb/s) via ICH7, connecting
one device per channel.

18

Desktop Board Features

Expandability

For system expansion, the Desktop Board provides the following expansion slots:

• One PCI Express x1 connector

• One PCI Express x16 connector

• Two PCI bus connectors

BIOS

The BIOS provides the Power-On Self-Test (POST), the BIOS Setup program, the
PCI/PCI Express and IDE auto-configuration utilities, and the video BIOS. The BIOS is
stored in the Serial Peripheral Interface (SPI) Flash component.

The BIOS can be updated by following the instructions on page 61 in Chapter 3.

Serial ATA and IDE Auto Configuration

If you install a Serial ATA or IDE device (such as a hard drive) in your computer, the
auto-configuration utility in the BIOS automatically detects and configures the device
for your computer. You do not need to run the BIOS Setup program after installing a
Serial ATA or IDE device. You can override the auto-configuration options by
specifying manual configuration in the BIOS Setup program.

PCI* and PCI Express* Auto Configuration

If you install a PCI/PCI Express add-in card in your computer, the PCI/PCI Express
auto-configuration utility in the BIOS automatically detects and configures the
resources (IRQs, DMA channels, and I/O space) for that add-in card. You do not need
to run the BIOS Setup program after you install a PCI/PCI Express add-in card.

19

Intel Desktop Board DG41TY Product Guide

Security Passwords

The BIOS includes security features that restrict whether the BIOS Setup program can
be accessed and who can boot the computer. A supervisor password and a user
password can be set for the BIOS Setup and for booting the computer, with the
following restrictions:

• The supervisor password gives unrestricted access to view and change all Setup

options. If only the supervisor password is set, pressing <Enter> at the password

prompt of Setup gives the user restricted access to Setup.

• If both the supervisor and user passwords are set, you must enter either the

supervisor password or the user password to access Setup. Setup options are then

available for viewing and changing depending on whether the supervisor or user

password was entered.

• Setting a user password restricts who can boot the computer. The password

prompt is displayed before the computer is booted. If only the supervisor

password is set, the computer boots without asking for a password. If both

passwords are set, you can enter either password to boot the computer.

Related Links:

For instructions on resetting the password, see Clearing Passwords on page 54.

Hardware Management Features

The hardware management features of Intel Desktop Board DG41TY enable the board
to be compatible with the Wired for Management (WfM) specification. The board has
several hardware management features including the following:

• Fan speed monitoring and control

• Thermal and voltage monitoring

• Chassis intrusion detection

20

Desktop Board Features

Hardware Monitoring and Fan Speed Control

The features of the hardware monitoring and fan speed control include:

• Monitoring of power supply voltages to detect levels above and below acceptable

values

• Fan speed controllers and sensors integrated into the legacy I/O controller

• Thermal sensors in the processor, GMCH, and ICH7, plus an onboard remote

sensor

• Thermally monitored closed-loop fan control, for all onboard fans, that can adjust

fan speed or switch the fans off as needed

Chassis Intrusion

The board supports a chassis security feature that detects if the chassis cover has
been removed. The security feature uses a mechanical switch on the chassis that can
be connected to the chassis intrusion header on the Desktop Board. See Figure 21 for
the location of the c

hassis intrusion header.

Power Management Features

Power management is implemented at several levels, including:

• Software support through the Advanced Configuration and Power Interface (ACPI)

• Hardware support:

⎯ Power connectors

⎯ Fan headers

⎯ LAN wake capabilities

⎯ Instantly Available PC technology (Suspend to RAM)

⎯ +5 V standby power indicator LED

⎯ Wake from USB

⎯ Power Management Event signal (PME#) wakeup support

⎯ WAKE# signal wake-up support

• ENERGY STAR capable

ACPI

ACPI gives the operating system direct control over the power management and Plug
and Play functions of a computer. The use of ACPI with the Desktop Board requires an
operating system that provides full ACPI support.

21

Intel Desktop Board DG41TY Product Guide

Hardware Support

Power Connectors

ATX12V-compliant power supplies can turn off the computer power through system
control. When an ACPI-enabled computer receives the correct command, the power
supply removes all non-standby voltages.

When resuming from an AC power failure, the computer returns to the power state it
was in before power was interrupted (either on or off). The computer’s response can
be set by using the Last Power State feature in the BIOS Setup program’s Boot menu.

The Desktop Board has two power connectors. See Figure 24 on page 52 for the
location of the power co

Fan Headers

The function/operation of the fans is as follows:

• The fans are on when the computer is in the ACPI S0 state.

• The fans are off when the computer is in the ACPI S3, S4, or S5 state.

• Each fan header is wired to a tachometer input of the hardware monitoring and

control device.

• All fan headers support closed-loop fan control that can adjust the fan speed or

switch the fan on or off as needed.

• All fan headers have a +12 V DC connection.

nnectors.

The Desktop Board has a 4-pin processor fan header and two 3-pin chassis fan
headers.

LAN Wake Capabilities

CAUTION

For LAN wake capabilities, the 5 V standby line for the power supply must be capable
of delivering adequate +5 V standby current. Failure to provide adequate standby
current when using this feature can damage the power supply.

LAN wakeup capabilities enable remote wake-up of the computer through a network.
The LAN subsystem monitors network traffic and upon detecting a Magic Packet*
frame, it asserts a wake-up signal that powers up the computer.

22

Desktop Board Features

Instantly Available PC Technology

CAUTIONS

For Instantly Available PC technology, the 5 V standby line for the power supply must
be capable of delivering adequate +5 V standby current. Failure to provide adequate
standby current when using this feature can damage the power supply and/or effect
ACPI S3 sleep state functionality.

Power supplies used with this Desktop Board must be able to provide enough standby
current to support the standard Instantly Available (ACPI S3 sleep state) configuration.
If the standby current necessary to support multiple wake events from the PCI and/or
USB buses exceeds power supply capacity, the Desktop Board may lose register
settings stored in memory.

Instantly Available PC technology enables the board to enter the ACPI S3 (Suspend-to­RAM) sleep state. While in the S3 sleep state, the computer will appear to be off. If
the computer has a dual-colored power LED on the front panel, the sleep state is
indicated by the LED turning amber. When signaled by a wake-up device or event, the
computer quickly returns to its last known awake state.

The Desktop Board supports the PCI Bus Power Management Interface Specification.
Add-in cards that support this specification can participate in power management and
can be used to wake the computer.

+5 V Standby Power Indicator LED

CAUTION

If the AC power has been switched off and the standby power indicator is still lit,
disconnect the power cord before installing or removing any devices connected to the
board. Failure to do so could damage the board and any attached devices.

The Desktop Board’s standby power indicator, shown in Figure 3, is lit when there is
standby power still present on the board even when the computer appears to be off.
For example, when this LED is lit, standby power is still present at the memory module
sockets and the PCI bus connectors.

Figure 3. Location of the Standby Power Indicator

23

Intel Desktop Board DG41TY Product Guide

Related Links:

For more information on standby current requirements for the Desktop Board, refer to
the Technical Product Specification by going to the following link, finding the product,
and selecting Product Documentation from the left-hand menu:

http://support.intel.com/support/motherboards/desktop/

Wake from USB

NOTE

Wake from USB requires the use of a USB peripheral that supports Wake from USB.

USB bus activity wakes the computer from an ACPI S1 or S3 state.

PME# Signal Wake-up Support

When the PME# signal on the PCI bus is asserted, the computer wakes from an ACPI
S1, S3, S4, or S5 (LAN only) state.

WAKE# Signal Wake-up Support

When the WAKE# signal on the PCI Express bus is asserted, the computer wakes from
an ACPI S1, S3, S4, or S5 (LAN only) state.

ENERGY STAR* Capable

In 2007, the US Department of Energy and the US Environmental Protection Agency
revised the ENERGY STAR requirements. Intel worked directly with these two
governmental agencies to define the new requirements. This Desktop Board meets
the ENERGY STAR Category B requirements.

For more information concerning ENERGY STAR, go to

http://www.intel.com/go/EnergyStar

Speaker

A speaker is mounted on the Desktop Board. The speaker provides audible error code
(beep code) information during the Power-On Self-Test (POST).

Battery

A battery on the Desktop Board keeps the values in CMOS RAM and the clock current
when the computer is turned off. Go to page 55 for instructions on how to replace the
battery.

24

Desktop Board Features

Real-Time Clock

The Desktop Board has a time-of-day clock and 100-year calendar. The battery on the
Desktop Board keeps the clock current when the computer is turned off.

25

Intel Desktop Board DG41TY Product Guide

26

2 Installing and Replacing Desktop

Board Components

This chapter tells you how to:

• Install the I/O shield

• Install and remove the Desktop Board

• Install and remove a processor

• Install and remove memory

• Install and remove a PCI Express x16 card

• Connect the diskette drive cable

• Connect the IDE and Serial ATA cables

• Connect to the internal headers and connectors

• Connect to the audio system

• Connect chassis fan and power supply cables

• Set the BIOS configuration jumper

• Clear passwords

• Replace the battery

Before You Begin

CAUTION

The procedures in this chapter assume familiarity with the general terminology
associated with personal computers and with the safety practices and regulatory
compliance required for using and modifying electronic equipment.

Disconnect the computer from its power source and from any telecommunications
links, networks, or modems before performing any of the procedures described in this
chapter. Failure to disconnect power, telecommunications links, networks, or modems
before you open the computer or perform any procedures can result in personal injury
or equipment damage. Some circuitry on the board can continue to operate even
though the front panel power button is off.

Follow these guidelines before you begin:

• Always follow the steps in each procedure in the correct order.

• Set up a log to record information about your computer, such as model, serial

numbers, installed options, and configuration information.

• Electrostatic discharge (ESD) can damage components. Perform the procedures

described in this chapter only at an ESD workstation using an antistatic wrist strap

and a conductive foam pad. If such a station is not available, you can provide

some ESD protection by wearing an antistatic wrist strap and attaching it to a

metal part of the computer chassis.

27

Intel Desktop Board DG41TY Product Guide

Installation Precautions

When you install and test the Intel Desktop Board, observe all warnings and cautions
in the installation instructions.

To avoid injury, be careful of:

• Sharp pins on connectors

• Sharp pins on printed circuit assemblies

• Rough edges and sharp corners on the chassis

• Hot components (such as processors, voltage regulators, and heat sinks)

• Damage to wires that could cause a short circuit

Observe all warnings and cautions that instruct you to refer computer servicing to
qualified technical personnel.

Prevent Power Supply Overload

Do not overload the power supply output. To avoid overloading the power supply,
make sure that the calculated total current loads of all the modules within the
computer is less than the output current rating of each of the power supply output
circuits.

Observe Safety and Regulatory Requirements

Read and adhere to the instructions in this section and the instructions supplied with
the chassis and associated modules. If you do not follow these instructions and the
instructions provided by the chassis and module suppliers, you increase safety risk and
the possibility of noncompliance with regional laws and regulations. If the instructions
for the chassis are inconsistent with these instructions or the instructions for
associated modules, contact the supplier’s technical support to find out how you can
ensure that your computer meets safety and regulatory requirements.

Related Links

For information about regulatory compliance, go to Appendix B on page 67.

28

Installing and Replacing Desktop Board Components

Installing the I/O Shield

The Desktop Board comes with an I/O shield. When installed in the chassis, the shield
blocks radio frequency transmissions, protects internal components from dust and
foreign objects, and promotes correct airflow within the chassis.

Install the I/O shield before installing the Desktop Board in the chassis. Place the
shield inside the chassis as shown in Figure 4. Press the shield into place so that it fits
t

ightly and securely. If the shield does not fit, obtain a properly sized shield from the

chassis supplier.

Figure 4. Installing the I/O Shield

29

Intel Desktop Board DG41TY Product Guide

Installing and Removing the Desktop Board

CAUTION

Only qualified technical personnel should do this procedure. Disconnect the computer
from its power source before performing the procedures described here. Failure to
disconnect the power before you open the computer can result in personal injury or
equipment damage.

Refer to your chassis manual for instructions on installing and removing the Desktop
Board.

Figure 5 shows the location of the mounti
DG41TY.

Figure 5. Intel Desktop Board DG41TY Mounting Screw Hole Locations

ng screw holes for Intel Desktop Board

30

Installing and Replacing Desktop Board Components

Installing and Removing a Processor

Instructions on how to install the processor to the Desktop Board are given below.

Installing a Processor

CAUTION

Before installing or removing the processor, make sure the AC power has been
removed by unplugging the power cord from the computer; the standby power LED
should not be lit (see Figure 3 on page 23). Failure to do so could damage the
processor and the boar

To install a processor, follow these instructions:

1. Observe the precautions in "Before You Begin" on page 27.

2. Open the so

(Figure 6, A and B).

cket lever by pushing the lever down and away from the socket

d.

Figure 6. Lift the Socket Lever

31

Intel Desktop Board DG41TY Product Guide

3. Lift the load plate (Figure 7, A). Do not touch the socket contacts (Figure 7, B).

Figure 7. Lift the Load Plate

4. Remove the plastic protective socket cover from the load plate (Figure 8). Do not

discard the protective socket cover. Always replace the socket cover if the

processor is removed from the socket.

Figure 8. Remove the Protective Socket Cover

32

Installing and Replacing Desktop Board Components

5. Remove the processor from the protective processor cover. Hold the processor

only at the edges, being careful not to touch the bottom of the processor (see

Figure 9). Do not discard the

protective processor cover. Always replace the

processor cover if the processor is removed from the socket.

Figure 9. Remove the Processor from the Protective Processor Co ver

6. Hold the processor with your thumb and index fingers oriented as shown in

Figure 10. Make sure your fingers align to the socket cutouts (Figure 10, A). Align

notches

dow

(Figure 10, B) with the socket (Figure 10, C). Lower the processor straight

n without tilting or sliding it in the socket.

Figure 10. Install the Processor

33

Intel Desktop Board DG41TY Product Guide

7. Pressing down on the load plate (Figure 11, A), close and engage the socket lever

(Figure 11, B).

Figure 11. Close the Load Plate

Installing the Processor Fan Heat Sink

Intel Desktop Board DG41TY has mounting holes for a processor fan heat sink. For
instructions on how to attach the processor fan heat sink to the Desktop Board, refer
to the boxed processor manual.

34

Installing and Replacing Desktop Board Components

Connecting the Processor Fan Heat Sink Cable

Connect the processor fan heat sink cable to the 4-pin processor fan header (see
Figure 12). A fan with a 4-pi
however, a fan with a 3-pin connector (Figure 12, B) can be used. However, since the
fan

with a 3-pin connector cannot use the onboard fan control, the fan will always

operate at full speed.

n connector as shown in Figure 12, A is recommended;

Figure 12. Connecting the Processor Fan Heat Sink Cable to the

Processor Fan Header

35

Intel Desktop Board DG41TY Product Guide

Removing the Processor

For instructions on how to remove the processor fan heat sink and processor, refer to
the processor installation manual.

Installing and Removing Memory

NOTE

To be fully compliant with all applicable Intel SDRAM memory specifications, the board
requires DIMMs that support the Serial Presence Detect (SPD) data structure.

The desktop board has two 240-pin DDR2 DIMM sockets providing Channel A and
Channel B. For optimum dual-channel performance, install a matched pair of DIMMs
equal in speed and size (see Figure 13).

Figure 13. Dual Channel Memory Configuration Example

NOTE

All other memory configurations will result in single channel memory operation.

36

Installing and Replacing Desktop Board Components

Installing DIMMs

To make sure you have the correct DIMM, place it on the illustration of the DDR2
DIMM in Figure 14. All the notches should match with the DDR2 DIMM.

Figure 14. Use DDR2 DIMMs

37

Intel Desktop Board DG41TY Product Guide

To install a DIMM, follow these steps:

1. Observe the precautions in "Before You Begin" on page 27.

2. Turn off all peripheral devices connected to the

computer. Turn off the computer

and disconnect the AC power cord.

3. Remove the computer’s cover and locate the DIMM sockets (see Figure 15).

Figure 15. Installing a DIMM

4. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the

open position.

5. Holding the DIMM by the edges, remove it from its anti-static package.

6. Position the DIMM above the socket. Align the small notch at the bottom edge of

the DIMM with the keys in the socket (see inset in Figure 15).

38

Installing and Replacing Desktop Board Components

7. Insert the bottom edge of the DIMM into the socket.

8. When the DIMM is inserted, push down on the top edge of the DIMM until the

retaining clips snap into place. Make sure the clips are firmly in place.

9. Replace the computer’s cover and reconnect the AC power cord.

Removing DIMMs

To remove a DIMM, follow these steps:

1. Observe the precautions in "Before You Begin" on page 27.

2. Turn off all peripheral devices connected to the

3. Remove the AC power cord from the computer.

4. Remove the computer’s cover.

5. Gently spread the retaining clips at each end of the DIMM socket. The DIMM pops

out of the socket.

6. Hold the DIMM by the edges, lift it away from the socket, and store it in an

anti-static package.

7. Reinstall and reconnect any parts you removed or disconnected to reach the DIMM

sockets.

8. Replace the computer’s cover and reconnect the AC power cord.

computer. Turn off the computer.

Installing and Removing a PCI Express x16
Card

CAUTION

When installing a PCI Express x16 card on the Desktop Board, ensure that the card is
fully seated in the PCI Express x16 connector before you power on the system. If the
card is not fully seated in the PCI Express connector, an electrical short may result
across the PCI Express connector pins. Depending on the over-current protection of
the power supply, certain Desktop Board components and/or traces may be damaged.

39

Intel Desktop Board DG41TY Product Guide

Installing a PCI Express x16 Card

CAUTION

When installing a PCI Express x16 card on the desktop board, ensure that the card is
fully seated in the PCI Express x16 connector before you power on the system. If the
card is not fully seated in the PCI Express connector, an electrical short may result
across the PCI Express connector pins. Depending on the over-current protection of
the power supply, certain desktop board components and/or traces may be damaged.

1. Observe the precautions in "Before You Begin" on page 27.

2. Place the card in the PCI E

t

he card until it is completely seated in the connector and the card retention notch

snaps into place around the retention mechanism pin.

3. Secure the card’s metal bracket to the chassis back panel with a screw

(Figure 16, B).

xpress x16 connector (Figure 16, A) and press down on

Figure 16. Installing a PCI Express x16 Card

40

Installing and Replacing Desktop Board Components

Removing the PCI Express x16 Card

Follow these instructions to remove the PCI Express x16 card from the connector:

1. Observe the precautions in "Before You Begin" on page 27.

2. Remove the

chassis bac

3. Push the card ejector lever down using the tip of a pencil or similar tool in the

notch (Figure 17, B). This will release the card from the connector (Figure 17, C).

4. P

ull the card straight up.

screw (Figure 17, A) that secures the card’s metal bracket to the

k panel.

Figure 17. Removing a PCI Express x16 Card

41

Intel Desktop Board DG41TY Product Guide

Connecting the Diskette Drive Cable

The diskette drive cable can be used to connect a single diskette drive to the Desktop
Board.

For correct function of the cable:

1. Observe the precautions in "Before You Begin" on page 27.

2. Attach

Desktop Board (Figure 18, A).

3. Attach the c

the cable end labeled P1 to the diskette drive connector on the Intel

able end labeled P2 to the diskette drive (Figure 18, B).

Figure 18. Connecting the Diskette Drive Cable

42

Installing and Replacing Desktop Board Components

Connecting the IDE Cable

The IDE cable can be used to connect two IDE drives to the Desktop Board. The cable
supports the ATA-66/100 transfer protocol. Figure 19 shows the correct installation of
the cable.

NOTES

ATA-66/100 compatible cables are backward compatible with drives using slower IDE
transfer protocols. If an ATA-66/100 disk drive and a disk drive using any other IDE
transfer protocol are attached to the same cable, the maximum transfer rate between
the drives may be reduced to that of the slowest drive.

Do not connect an ATA device as a slave on the same IDE cable as an ATAPI master
device. For example, do not connect an ATA hard drive as a slave to an ATAPI
CD-ROM drive.

For correct function of the cable:

1. Observe the precautions in "Before You Begin" on page 27.

2. Attach the cable end with the single connect

(Figure 19, A).

3. Attach the cable end with the two cl

the drives (Figure 19, B).

osely spaced connectors (gray and black) to

or (blue) to the Intel Desktop Board

Figure 19. Connecting the IDE Cable

43

Intel Desktop Board DG41TY Product Guide

Connecting the Serial ATA (SATA) Cables

SATA cables support the Serial ATA protocol. Each cable can be used to connect a
single internal SATA drive to the Desktop Board. For correct cable function:

1. Observe the precautions in “Before You Begin” on page 27.

2. Attach

(Figure 20, A) and attach the other end of the

(Figure 20, B).

one end of the SATA cable to one of the SATA connectors on the board

cable to the SATA drive

Figure 20. Connecting a Serial ATA Cable

44

Installing and Replacing Desktop Board Components

Connecting to the Internal Headers and
Connectors

Before connecting cables to the internal headers and connectors, observe the
precautions in “Before You Begin” on page 27. Figure 21 shows the location of the
internal headers and

connectors for Intel Desktop Board DG41TY.

Figure 21. Internal Headers and Connectors

45

Intel Desktop Board DG41TY Product Guide

S/PDIF Connector

Figure 21, A on page 45 shows the location of the S/PDIF connector. Figure 5 shows
the pin assignments for the S/PDIF connector.

Table 5. S/PDIF Connector

Pin Description

1 VCC
2 SPDIF OUT
3 Ground

Front Panel Audio Header

The front panel audio header shown in Figure 21, B on page 45 supports both High
Definition (HD) Audio and AC’97 Audio.

Table 7 shows the pin assignments and signal names for HD Audio and Table 8 shows
the pin as

signments and signal names for AC’97 Audio.

HD Audio is the default setting for the front panel audio header. A Front Panel Audio
Select jumper block is provided on the Desktop Board (see Figure 1, BB). Use the
jumper to switch

the header from the HD Audio pinout to the AC ’97 pinout. The

jumper settings are shown in Table 6.

Table 6.

Jumper Setting Audio Mode

1-2 AC ‘97
2-3 HD Audio

Jumper Settings for the Front Panel Audio Select Jumper Block

Table 7. Front Panel Audio Signal Names for Intel HD Audio

Pin Signal Name Pin Signal Name

1 PORT 1L (Microphone) 2 GND
3 PORT 1R (Microphone) 4 PRESENCE#
5 PORT 2R (Headphone) 6 SENSE1_RETURN
7 SENSE_SEND 8 KEY (no pin)
9 PORT 2L (Headphone) 10 SENSE2_RETURN

46

Installing and Replacing Desktop Board Components

Table 8. Front Panel Audio Header Signal Names for AC’97 Audio

Pin Signal Name Pin Signal Name

1 MIC 2 AUD_GND
3 MIC_BIAS 4 AUD_GND
5 FP_OUT_R 6 FP_RETURN_R
7 AUD_5V 8 KEY (no pin)
9 FP_OUT_L 10 FP_RETURN_L

Serial Port Header

See Figure 21, C on page 45 for the location of the serial port header. Table 9 shows
the pin assignments for the serial port header.

Table 9. Serial Port Header Signal Names

Pin Signal Name Pin Signal Name

1 DCD 2 RXD#
3 TXD# 4 DTR
5 Ground 6 DSR
7 RTS 8 CTS
9 RI 10 No Connection

HD Audio Link Header

See Figure 21, D for the location of the HD Audio Link header. Table 10 shows the pin
assignments for the header.

Table 10. HD Audio Link Header Signal Names

Pin Signal Name Pin Signal Name

1 BCLK 2 Ground
3 RST# 4 DVDD_IO
5 SYNC 6 Ground
7 SDO 8 3.3V_DVDD_CORE
9 SDI0 10 +12 V
11 SDI1 12 Key
13 No Connection 14 3.3V_DUAL
15 No Connection 16 Ground

47

Intel Desktop Board DG41TY Product Guide

Chassis Intrusion Header

Figure 21, E on page 45 shows the location of the chassis intrusion header. This
header can be connected to a mechanical switch on the chassis to detect if the chassis
cover is removed.

Table 11 shows the pin assignments for t

he chassis intrusion header.

Table 11. Chassis Intrusion Header

Pin Description

1 Intruder
2 Ground

Front Panel Header

Before connecting to the front panel header, observe the precautions in "Before You
Begin" on page 27. See Figure 21, F on page 45 for the location of the multi-colored
front panel

Table 12 shows the pin assignments for t

Table 12. Front Panel Header

Pin Description In/Out Pin Description In/Out

1 Hard disk LED pull-up to +5 V Out 2 Front panel green LED Out
3 Hard disk active LED Out 4 Front panel yellow LED Out

5 Ground 6 Power switch In
7 Reset switch In 8 Ground

9 Power Out 10 No pin

header.

he front panel header.

Hard Drive Activity LED Power LED

Reset Switch On/Off Switch

Power Not Connected

48

Installing and Replacing Desktop Board Components

Alternate Front Panel Power LED Header

Figure 21, G on page 45 shows the location of the alternate front panel power LED
header. Pins 1 and 3 of this header duplicate the signals on pins 2 and 4 of the front
panel header. If your chassis has a three-pin power LED cable, connect it to this
header.

Table 13 shows the pin assignments for the al

Table 13. Alternate Front Panel Power LED Header

Pin Description In/Out

1 Front panel green LED Out
2 No pin
3 Front panel yellow LED Out

ternate front panel power LED header.

USB 2.0 Headers

Before connecting to the USB 2.0 headers, observe the precautions in "Before You
Begin" on page 27. See Figure 21, H on page 45 for the location of the three USB 2.0
headers. Table 14 shows the pin assignments for each USB 2.0
header can be used to connect two USB devices.

Table 14. USB 2.0 Header Signal Names

USB Port A USB Port B

Pin Signal Name Pin Signal Name

1 Power (+5 V) 2 Power (+5 V)
3 D- 4 D­5 D+ 6 D+
7 Ground 8 Ground
9 Key 10 No Connection

Note: USB ports may be assigned as needed.

header. Each USB

NOTE

Computer systems that have an unshielded cable attached to a USB port might not
meet FCC Class B requirements, even if no device or a low-speed USB device is
attached to the cable. Use a shielded cable that meets the requirements for a
full-speed USB device.

49

Intel Desktop Board DG41TY Product Guide

Connecting to the Back Panel Audio
Connectors

After installing the audio driver from the Intel Express Installer CD-ROM, the multi­channel audio feature can be enabled. Figure 22 shows the back panel audio
connectors
Table 3 on page 16 for audio connector retasking information.

. The default connector assignments are shown in the figure. Refer to

Item Description

A Line In

B Line Out

C Mic In

Figure 22. Back Panel Audio Connectors

NOTE

The back panel line out connector is designed to power either headphones or amplified
speakers only. Poor audio quality may occur if passive (non-amplified) speakers are
connected to this output.

50

Installing and Replacing Desktop Board Components

Connecting Chassis Fan and Power Supply
Cables

Connecting Chassis Fan Cables

Connect chassis fan cables to the 3-pin chassis fan headers on the Desktop Board.
Figure 23 shows the location of the chassis fa

n headers.

Figure 23. Location of the Chassis Fan Headers

51

Intel Desktop Board DG41TY Product Guide

Connecting Supply Power Cables

CAUTION

Failure to use an appropriate power supply and/or not connecting the 12 V (2 x 2 pin)
power connector to the Desktop Board may result in damage to the board or the
system may not function properly.

The 2 x 12 pin main power connector on the Desktop Board is backwards compatible
with ATX12V power supplies with 2 x 10 connectors. Figure 24 shows the location of
the

Desktop Board power connectors.

Figure 24. Connecting Power Supply Cables

1. Observe the precautions in "Before You Begin" on page 27.

2. Connect the main power supply cable to the 2 x 12 pin connector.

3. Connect the 12 V processor core voltage power supply cable to the 2 x 2 pin

connector.

52

Installing and Replacing Desktop Board Components

Setting the BIOS Configuration Jumper

NOTE

Always turn off the power and unplug the power cord from the computer before
moving the jumper. Moving the jumper with the power on may result in unreliable
computer operation.

Figure 25 shows the location of the Desktop Board’s BIOS confi

guration jumper block.

Figure 25. Location of the BIOS Configuration Jumper Block

The three-pin BIOS jumper block enables all board configurations to be done in the
BIOS Setup program. Table 15 shows the jumper setti

ngs for the BIOS Setup

program modes.

Table 15. Jumper Settings for the BIOS Setup Program Modes

Jumper Setting Mode Description

Normal (default) (1-2) The BIOS uses the current configuration and

passwords for booting.

Configure (2-3) After the Power-On Self-Test (POST) runs, the

Recovery (None) The BIOS recovers data in the event of a failed

BIOS displays the Maintenance Menu. Use this
menu to clear passwords.

BIOS update.

53

Intel Desktop Board DG41TY Product Guide

Clearing Passwords

This procedure assumes that the board is installed in the computer and the
configuration jumper block is set to normal mode.

1. Observe the precautions in "Before You Begin" on page 27.

2. Turn off all peripheral devices connected to the

Disconnect the computer’s power cord from the AC power source (wall outlet or

power adapter).

3. Remove the computer cover.

4. Find the configuration jumper block (see Figure 25).

5. Place the jumper on pins 2-3 as shown

6. Replace the cover, plug in the computer, turn on the computer, and allow it to

boot.

7. The computer starts the Setup program. Setup displays the Maintenance menu.

8. Use the arrow keys to select Clear Passwords. Press <Enter> and Setup displays a

pop-up screen requesting that you confirm clearing the password. Select Yes and

press <Enter>.

Setup displays the maintenance menu again.

9. Press <F10> to save the current values and exit Setup.

10. Turn off the computer. Disconnect the computer’s power cord from the AC power

source.

11. Remove the computer cover.

12. To restore normal operation, place the jumper on pins 1-2 as shown below.

below.

computer. Turn off the computer.

13. Replace the cover, plug in the computer, and turn on the computer.

54

Installing and Replacing Desktop Board Components

Replacing the Battery

A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When
the computer is not plugged into a wall socket, the battery has an estimated life of
three years. When the computer is plugged in, the standby current from the power
supply extends the life of the battery. The clock is accurate to ± 13 minutes/year at
25 ºC with 3.3 VSB applied.

When the voltage drops below a certain level, the BIOS Setup program settings stored
in CMOS RAM (for example, the date and time) might not be accurate. Replace the
battery with an equivalent one. Figure 26 on page 59 shows the location of the
battery.

CAUTION

Risk of explosion if the battery is replaced with an incorrect type. Batteries should be
recycled where possible. Disposal of used batteries must be in accordance with local
environmental regulations.

PRÉCAUTION

Risque d'explosion si la pile usagée est remplacée par une pile de type incorrect. Les
piles usagées doivent être recyclées dans la mesure du possible. La mise au rebut des
piles usagées doit respecter les réglementations locales en vigueur en matière de
protection de l'environnement.

FORHOLDSREGEL

Eksplosionsfare, hvis batteriet erstattes med et batteri af en forkert type. Batterier
bør om muligt genbruges. Bortskaffelse af brugte batterier bør foregå i
overensstemmelse med gældende miljølovgivning.

OBS!

Det kan oppstå eksplosjonsfare hvis batteriet skiftes ut med feil type. Brukte batterier
bør kastes i henhold til gjeldende miljølovgivning.

VIKTIGT!

Risk för explosion om batteriet ersätts med felaktig batterityp. Batterier ska kasseras
enligt de lokala miljövårdsbestämmelserna.

VARO

Räjähdysvaara, jos pariston tyyppi on väärä. Paristot on kierrätettävä, jos se on
mahdollista. Käytetyt paristot on hävitettävä paikallisten ympäristömääräysten
mukaisesti.

55

Intel Desktop Board DG41TY Product Guide

VORSICHT

Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr. Die Batterie
darf nur durch denselben oder einen entsprechenden, vom Hersteller empfohlenen
Batterietyp ersetzt werden. Entsorgen Sie verbrauchte Batterien den Anweisungen
des Herstellers entsprechend.

AVVERTIMENTO

Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto.
Utilizzare solo pile uguali o di tipo equivalente a quelle consigliate dal produttore. Per
disfarsi delle pile usate, seguire le istruzioni del produttore.

PRECAUCIÓN

Existe peligro de explosión si la pila no se cambia de forma adecuada. Utilice
solamente pilas iguales o del mismo tipo que las recomendadas por el fabricante del
equipo. Para deshacerse de las pilas usadas, siga igualmente las instrucciones del
fabricante.

WAARSCHUWING

Er bestaat ontploffingsgevaar als de batterij wordt vervangen door een onjuist type
batterij. Batterijen moeten zoveel mogelijk worden gerecycled. Houd u bij het
weggooien van gebruikte batterijen aan de plaatselijke milieuwetgeving.

ATENÇÃO

Haverá risco de explosão se a bateria for substituída por um tipo de bateria incorreto.
As baterias devem ser recicladas nos locais apropriados. A eliminação de baterias
usadas deve ser feita de acordo com as regulamentações ambientais da região.

AŚCIAROŽZNAŚĆ

Існуе рызыка выбуху, калі заменены акумулятар неправільнага тыпу.
Акумулятары павінны, па магчымасці, перепрацоўвацца. Пазбаўляцца ад старых
акумулятараў патрэбна згодна з мясцовым заканадаўствам па экалогіі.

UPOZORNÌNÍ

V případě výměny baterie za nesprávný druh může dojít k výbuchu. Je-li to možné,
baterie by měly být recyklovány. Baterie je třeba zlikvidovat v souladu s místními
předpisy o životním prostředí.

Προσοχή

Υπάρχει κίνδυνος για έκρηξη σε περίπτωση που η μπαταρία αντικατασταθεί από μία
λανθασμένου τύπου. Οι μπαταρίες θα πρέπει να ανακυκλώνονται όταν κάτι τέτοιο είναι
δυνατό. Η απόρριψη των χρησιμοποιημένων μπαταριών πρέπει να γίνεται σύμφωνα με
τους κατά τόπο περιβαλλοντικούς κανονισμούς.

56

Installing and Replacing Desktop Board Components

VIGYÁZAT

Ha a telepet nem a megfelelő típusú telepre cseréli, az felrobbanhat. A telepeket
lehetőség szerint újra kell hasznosítani. A használt telepeket a helyi környezetvédelmi
előírásoknak megfelelően kell kiselejtezni.

AWAS

Risiko letupan wujud jika bateri digantikan dengan jenis yang tidak betul. Bateri
sepatutnya dikitar semula jika boleh. Pelupusan bateri terpakai mestilah mematuhi
peraturan alam sekitar tempatan.

OSTRZEŻENIE

Istnieje niebezpieczeństwo wybuchu w przypadku zastosowania niewłaściwego typu
baterii. Zużyte baterie należy w miarę możliwości utylizować zgodnie z odpowiednimi
przepisami ochrony środowiska.

PRECAUŢIE

Risc de explozie, dacă bateria este înlocuită cu un tip de baterie necorespunzător.
Bateriile trebuie reciclate, dacă este posibil. Depozitarea bateriilor uzate trebuie să
respecte reglementările locale privind protecţia mediului.

ВНИМАНИЕ

При использовании батареи несоответствующего типа существует риск ее взрыва.
Батареи должны быть утилизированы по возможности. Утилизация батарей должна
проводится по правилам, соответствующим местным требованиям.

UPOZORNENIE

Ak batériu vymeníte za nesprávny typ, hrozí nebezpečenstvo jej výbuchu. Batérie by
sa mali podľa možnosti vždy recyklovať. Likvidácia použitých batérií sa musí vykonávať
v súlade s miestnymi predpismi na ochranu životného prostredia.

POZOR

Zamenjava baterije z baterijo drugačnega tipa lahko povzroči eksplozijo.
Če je mogoče, baterije reciklirajte. Rabljene baterije zavrzite v skladu z lokalnimi

okoljevarstvenimi predpisi.

.

57

Intel Desktop Board DG41TY Product Guide

UYARI

Yanlış türde pil takıldığında patlama riski vardır. Piller mümkün olduğunda geri
dönüştürülmelidir. Kullanılmış piller, yerel çevre yasalarına uygun olarak atılmalıdır.

OСТОРОГА

Використовуйте батареї правильного типу, інакше існуватиме ризик вибуху.
Якщо можливо, використані батареї слід утилізувати. Утилізація використаних
батарей має бути виконана згідно місцевих норм, що регулюють охорону довкілля.

58

Installing and Replacing Desktop Board Components

To replace the battery, follow these steps:

1. Observe the precautions in "Before You Begin" (see page 27).

2. Turn off all peripheral devices connected to t

he computer. Disconnect the

computer’s power cord from the AC power source (wall outlet or power adapter).

3. Remove the computer cover.

4. Locate the battery on the board (see Figure 26).

5. P

ush the battery retention clip aside and remove the battery from the connector as

shown in Figure 26. Note the orientation of the “+” and “-” on the battery.

6. Instal

l the new battery in the connector, making sure to orient the “+” and “-”

correctly.

7. Replace the computer cover.

Figure 26. Removing the Battery

59

Intel Desktop Board DG41TY Product Guide

60

3 Updating the BIOS

The BIOS Setup program can be used to view and change the BIOS settings for the
computer. You can access the BIOS Setup program by pressing the <F2> key after
the Power-On Self-Test (POST) memory test begins and before the operating system
boot begins.

This chapter tells you how to update the BIOS by either using the Intel Express BIOS
Update utility or the Iflash Memory Update utility, and how to recover the BIOS if an
update fails.

Updating the BIOS with the Intel® Express
BIOS Update Utility

With the Intel Express BIOS Update utility you can update the system BIOS while in
the Windows environment. The BIOS file is included in an automated update utility
that combines the functionality of the Intel
of use of Windows-based installation wizards.

®

Flash Memory Update Utility and the ease

To update the BIOS with the Intel Express BIOS Update utility:

1. Go to the Intel World Wide Web site:

http://support.intel.com/support/motherboards/desktop/

2. Navigate to the Intel Desktop Board DG41TY page, click “[view] Latest BIOS

updates,” and select the Express BIOS Update utility file.

3. Download the file to your hard drive. (You can also save this file to a removable

USB device. This is useful if you are updating the BIOS for multiple identical

systems.)

4. Close all other applications. This step is required. Your system will be rebooted at

the last Express BIOS Update window.

5. Double-click the executable file from the location on your hard drive where it was

saved. This runs the update program.

6. Follow the instructions provided in the dialog boxes to complete the BIOS update.

61

Intel Desktop Board DG41TY Product Guide

Updating the BIOS with the ISO Image BIOS
Update File or the Iflash Memory Update
Utility

You can use the information in this section to update the BIOS using either the Iflash
Memory Update Utility or the ISO Image BIOS update file.

Obtaining the BIOS Update File

You can update to a new version of the BIOS by using the ISO Image BIOS update file
(recommended), or Iflash BIOS update file.

The ISO Image BIOS update file is a standardized image of a bootable CD-ROM that
can be used to create a bootable CD that will update the BIOS.

The Iflash BIOS update file is a compressed file that contains the files you need to
update the BIOS. The Iflash BIOS update file contains:

• New BIOS file

• Intel

• Intel Flash Memory Update Utility

®

Integrator Toolkit Configuration File (optional)

You can obtain either of these files through your computer supplier or by navigating to
the Intel Desktop Board DG41TY page on the Intel World Wide Web site at:

http://support.intel.com/support/motherboards/desktop

Navigate to the Intel Desktop Board DG41TY page, click “[view] Latest BIOS updates,” and
select the ISO Image BIOS Update or Iflash BIOS Update utility file.

Updating the BIOS with the ISO Image BIOS Update
File

The ISO Image BIOS update allows for the update of an Intel® Desktop Board BIOS to
the latest production release regardless of the operating system installed on the
computer's hard drive and without the need to remove the BIOS configuration jumper.
It requires a blank CD-R, a read/writeable CD drive, and software capable of
uncompressing and writing the ISO image file to CD.

The image uses ISOLINUX* bootloader and automatically launches a script to upgrade
the BIOS via the Iflash utility.

62

Updating the BIOS

CAUTION

Do not interrupt the process or the system may not function properly.

Follow these instructions to upgrade the BIOS using the ISO Image BIOS file:

1. Download the ISO Image BIOS file.

2. Using software capable of uncompressing and writing an ISO image file to CD, burn

the data to a blank CD.

NOTE

Copying the ISO Image BIOS file to CD will not work. The completed CD should
contain multiple files and a directory.

3. Insert the CD that was created in the CD-ROM drive of the computer to be

upgraded and boot the system.

4. When the "Press ENTER to continue booting from CD-ROM" prompt appears, press

the Enter key. The system will boot from the hard drive if no key is pressed within

15 seconds.

5. At the "Welcome to the Intel Desktop Board BIOS Upgrade CD-ROM" page, press

any key to confirm the BIOS upgrade operation.

6. Wait for the BIOS upgrade process to complete.

CAUTION

DO NOT POWER DOWN YOUR COMPUTER before the update is complete. The update
may take up to 5 minutes.

Updating the BIOS with the Iflash Memory Update
Utility

With the Iflash Memory update utility you can update the system BIOS from a
bootable CD-ROM, bootable USB flash drive, or other bootable USB media. The utility
available on the Intel World Wide Web site provides a simple method for creating a
bootable CD-ROM that will automatically update your BIOS. The Iflash BIOS update
files can also be extracted locally to your hard drive and copied to a bootable USB
flash drive or other bootable USB media.

The Iflash Memory update utility allows you to:

• Update the BIOS in flash memory

• Update the language section of the BIOS

NOTE

Review the instructions distributed with the update utility before attempting a BIOS
update.

63

Intel Desktop Board DG41TY Product Guide

CAUTION

Do not interrupt the process or the system may not function properly.

1. Uncompress the BIOS update file and copy the .BIO file, IFLASH.EXE, and .ITK file

(optional) to a bootable USB flash drive or other bootable USB media.

2. Configure the BIOS or use the F10 option during POST to boot to the USB device.

3. Manually run the IFLASH.EXE file from the USB device and manually update the

BIOS.

Recovering the BIOS

It is unlikely that anything will interrupt the BIOS update; however, if an interruption
occurs, the BIOS could be damaged. Due to BIOS size and recovery requirements, a
CD-R with the .BIO file in the root directory will be required.

Related Links:

For more information about updating the Intel Desktop Board BIOS or recovering from
a BIOS update failure, go to:

http://support.intel.com/support/motherboards/desktop

/sb/CS-022312.htm

64

A Error Messages and Indicators

Intel Desktop Board DG41TY reports POST errors in two ways:

• By sounding a beep code

• By displaying an error message on the monitor

BIOS Beep Codes

The BIOS also issues a beep code (one long tone followed by two short tones) during
POST if the video configuration fails (a faulty video card or no card installed) or if an
external ROM module does not properly checksum to zero. Table 16 lists the BIOS
codes.

Table 16.

Beep Description

3 No memory
Siren Processor overheat (on reboot)

Beep Codes

BIOS Error Messages

When a recoverable error occurs during the POST, the BIOS displays an error message
describing the problem. Table 17 gives an explanation of

Table 17. BIOS Error Messages

Error Message Explanation

PROCESSOR_THERMAL_TRIP_ERROR

MULTI_BIT_ECC_ERROR The firmware has detected that a Multi-Bit ECC Error occurred.
SINGLE_BIT_ECC_ERROR The firmware has detected that a Single-Bit ECC Error occurred.
CMOS_BATTERY_ERROR The firmware has detected that a CMOS battery failure occurred.
CMOS_CHECKSUM_ERROR The firmware has detected that a CMOS Checksum Error occurred.
CMOS_TIMER_ERROR

MEMORY_SIZE_DECREASE_ERROR

INTRUDER_DETECTION_ERROR The system chassis was opened.
SPD_TOLER_ERROR

MEM_OPTIMAL_ERROR

Processor was previously shutdown due to a thermal event
(overheating).

The firmware has detected that the system date/time has not
been set.

The firmware has detected that the system memory has
decreased.

SERIAL PRESENCE DETECT (SPD) device data missing or
inconclusive. Properly programmed SPD device data is required
for reliable operation.

The installed amount of memory in Channel A is not equal to the
amount of memory in Channel B. Maximum memory performance
is achieved with equal amounts of memory installed in each
channel.

the BIOS error messages.

65

Intel Desktop Board DG41TY Product Guide

66

B Regulatory Compliance

This appendix contains the following regulatory compliance information for Intel
Desktop Board DG41TY:

• Safety standards

• European Union Declaration of Conformity statement

• Product Ecology statements

• Electromagnetic Compatibility (EMC) regulations

• Product certifications

Safety Standards

Intel Desktop Board DG41TY complies with the safety standards stated in Table 18
when correctly installed in a compatible host system.

Table 18. Safety Standards

Regulation Title

UL 60950-1, First Edition Information Technology Equipment – Safety - Part 1: General

Requirements (USA and Canada)

EN 60950-1:2006, Second
Edition

IEC 60950-1:2005, Second
Edition

Information Technology Equipment – Safety - Part 1: General
Requirements (European Union)

Information Technology Equipment – Safety - Part 1: General
Requirements (International)

Place Battery Marking

There is insufficient space on this Desktop Board to provide instructions for replacing
and disposing of the Lithium ion coin cell battery. For system safety certification, the
statement below or an equivalent statement is required to be permanently and legibly
marked on the chassis near the battery.

CAUTION

Risk of explosion if the battery is replaced with an incorrect type. Batteries should be
recycled where possible. Disposal of used batteries must be in accordance with local
environmental regulations.

Related Links

For information about replacing the battery, go to page 55.

67

Intel Desktop Board DG41TY Product Guide

European Union Declaration of Conformity
Statement

We, Intel Corporation, declare under our sole responsibility that the product Intel®
Desktop Board DG41TY is in conformity with all applicable essential requirements
necessary for CE marking, following the provisions of the European Council Directives
2004/108/EC (EMC Directive) and 2006/95/EC (Low Voltage Directive).

The product is properly CE marked demonstrating this conformity and is for
distribution within all member states of the EU with no restrictions.

This product follows the provisions of the European Directives 2004/108/EC and
2006/95/EC.

Čeština Tento výrobek odpovídá požadavkům evropských směrnic 2004/108/EC a
2006/95/EC.

Dansk Dette produkt er i overensstemmelse med det europæiske direktiv
2004/108/EC & 2006/95/EC.

Dutch Dit product is in navolging van de bepalingen van Europees Directief
2004/108/EC & 2006/95/EC.

Eesti Antud toode vastab Euroopa direktiivides 2004/108/EC ja 2006/95/EC
kehtestatud nõuetele.

Suomi Tämä tuote noudattaa EU-direktiivin 2004/108/EC & 2006/95/EC määräyksiä.
Français Ce produit est conforme aux exigences de la Directive Européenne

2004/108/EC & 2006/95/EC.
Deutsch Dieses Produkt entspricht den Bestimmungen der Europäischen Richtlinie

2004/108/EC & 2006/95/EC.
Ελληνικά Το παρόν προϊόν ακολουθεί τις διατάξεις των Ευρωπαϊκών Οδηγιών

2004/108/EC και 2006/95/EC.
Magyar E termék megfelel a 2004/108/EC és 2006/95/EC Európai Irányelv

előírásainak.
Icelandic Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer

2004/108/EC & 2006/95/EC.
Italiano Questo prodotto è conforme alla Direttiva Europea 2004/108/EC &

2006/95/EC.
Latviešu Šis produkts atbilst Eiropas Direktīvu 2004/108/EC un 2006/95/EC

noteikumiem.

68

Regulatory Compliance

Lietuvių Šis produktas atitinka Europos direktyvų 2004/108/EC ir 2006/95/EC
nuostatas.

Malti Dan il-prodott hu konformi mal-provvedimenti tad-Direttivi Ewropej
2004/108/EC u 2006/95/EC.

Norsk Dette produktet er i henhold til bestemmelsene i det europeiske direktivet
2004/108/EC & 2006/95/EC.

Polski Niniejszy produkt jest zgodny z postanowieniami Dyrektyw Unii Europejskiej
2004/108/EC i 2006/95/EC.

Portuguese Este produto cumpre com as normas da Diretiva Européia 2004/108/EC
& 2006/95/EC.

Español Este producto cumple con las normas del Directivo Europeo 2004/108/EC &
2006/95/EC.

Slovensky Tento produkt je v súlade s ustanoveniami európskych direktív
2004/108/EC a 2006/95/EC.

Slovenščina Izdelek je skladen z določbami evropskih direktiv 2004/108/EC in
2006/95/EC.

Svenska Denna produkt har tillverkats i enlighet med EG-direktiv 2004/108/EC &
2006/95/EC.

Türkçe Bu ürün, Avrupa Birliği’nin 2004/108/EC ve 2006/95/EC yönergelerine uyar.

Product Ecology Statements

The following information is provided to address worldwide product ecology concerns
and regulations.

Recycling Considerations

As part of its commitment to environmental responsibility, Intel has implemented the

®

Intel

Product Recycling Program to allow retail consumers of Intel’s branded products

to return used products to selected locations for proper recycling.
Please consult http://www.intel.com/intel/other/ehs/product_ecology

for the details of this program, including the scope of covered products, available
locations, shipping instructions, terms and conditions, etc.

中文

作为其对环境责任之承诺的部分，英特尔已实施 Intel Product Recycling Program
（英特尔产品回收计划），以允许英特尔品牌产品的零售消费者将使用过的产品退还至指定地点作恰
当的重复使用处理。

请参考http://www.intel.com/intel/other/ehs/
了解此计划的详情，包括涉及产品之范围、回收地点、运送指导、条款和条件等。

product_ecology

69

Intel Desktop Board DG41TY Product Guide

Deutsch

Als Teil von Intels Engagement für den Umweltschutz hat das Unternehmen das Intel
Produkt-Recyclingprogramm implementiert, das Einzelhandelskunden von Intel
Markenprodukten ermöglicht, gebrauchte Produkte an ausgewählte Standorte für
ordnungsgemäßes Recycling zurückzugeben.

Details zu diesem Programm, einschließlich der darin eingeschlossenen Produkte,
verfügbaren Standorte, Versandanweisungen, Bedingungen usw., finden Sie auf der

http://www.intel.com/intel/other/ehs/product_ecology

Español

Como parte de su compromiso de responsabilidad medioambiental, Intel ha
implantado el programa de reciclaje de productos Intel, que permite que los
consumidores al detalle de los productos Intel devuelvan los productos usados en los
lugares seleccionados para su correspondiente reciclado.

Consulte la http://www.intel.com/intel/other/ehs/product_ecology
para ver los detalles del programa, que incluye los productos que abarca, los lugares
disponibles, instrucciones de envío, términos y condiciones, etc.

Français

Dans le cadre de son engagement pour la protection de l'environnement, Intel a mis
en œuvre le programme Intel Product Recycling Program (Programme de recyclage
des produits Intel) pour permettre aux consommateurs de produits Intel de recycler
les produits usés en les retournant à des adresses spécifiées.

Visitez la page Web http://www.intel.com/intel/other/ehs/product_ecology

pour en
savoir plus sur ce programme, à savoir les produits concernés, les adresses
disponibles, les instructions d'expédition, les conditions générales, etc.

日本語

インテルでは、環境保護活動の一環として、使い終えたインテル
ブランド製品を指定の場所へ返送していただき、リサイクルを適切に行えるよう、インテル製品リサイクル
プログラムを発足させました。

対象製品、返送先、返送方法、ご利用規約など、このプログラムの詳細情報は、http://www.intel.com/in

tel/other/ehs/product_ecology （英語）をご覧ください。

Malay

Sebagai sebahagian daripada komitmennya terhadap tanggungjawab persekitaran,
Intel telah melaksanakan Program Kitar Semula Produk untuk membenarkan
pengguna-pengguna runcit produk jenama Intel memulangkan produk terguna ke
lokasi-lokasi terpilih untuk dikitarkan semula dengan betul.

Sila rujuk http://www.intel.com/intel/other/ehs/product_ecology
butir-butir program ini, termasuklah skop produk yang dirangkumi, lokasi-lokasi
tersedia, arahan penghantaran, terma & syarat, dsb.

70

untuk mendapatkan

Regulatory Compliance

Portuguese

Como parte deste compromisso com o respeito ao ambiente, a Intel implementou o
Programa de Reciclagem de Produtos para que os consumidores finais possam enviar
produtos Intel usados para locais selecionados, onde esses produtos são reciclados de
maneira adequada.

Consulte o site http://www.intel.com/intel/other/ehs/product_ecology
obter os detalhes sobre este programa, inclusive o escopo dos produtos cobertos, os
locais disponíveis, as instruções de envio, os termos e condições, etc.

Russian

В качестве части своих обязательств к окружающей среде, в Intel создана
программа утилизации продукции Intel (Product Recycling Program) для
предоставления конечным пользователям марок продукции Intel возможности
возврата используемой продукции в специализированные пункты для должной
утилизации.

Пожалуйста, обратитесь на веб-сайт

http://www.intel.com/intel/other/ehs/product_ecology

программе, принимаемых продуктах, местах приема, инструкциях об отправке,
положениях и условиях и т.д.

Türkçe

Intel, çevre sorumluluğuna bağımlılığının bir parçası olarak, perakende tüketicilerin
Intel markalı kullanılmış ürünlerini belirlenmiş merkezlere iade edip uygun şekilde geri
dönüştürmesini amaçlayan Intel Ürünleri Geri Dönüşüm Programı’nı uygulamaya
koymuştur.

Bu programın ürün kapsamı, ürün iade merkezleri, nakliye talimatları, kayıtlar ve
şartlar v.s dahil bütün ayrıntılarını ögrenmek için lütfen

http://www.intel.com/intel/other/ehs/product_ecology

за информацией об этой

web sayfasına gidin.

(em Inglês) para

Lead-Free Desktop Board

This Desktop Board is a European Union Restriction of Hazardous Substances (EU
RoHS Directive 2002/95/EC) compliant product. EU RoHS restricts the use of six
materials. One of the six restricted materials is lead.

Intel Desktop Board DG41TY is lead-free although certain discrete components used
on the board contain a small amount of lead which is necessary for component
performance and/or reliability. This Desktop Board is referred to as “Lead-free second
level interconnect.” The board substrate and the solder connections from the board to
the components (second-level connections) are all lead-free.

China bans the same substances and has the same limits as EU RoHS; however it
requires different product marking and controlled substance information. The required
mark shows the Environmental Friendly Usage Period (EFUP). The EFUP is defined as
the number of years for which controlled listed substances will not leak or chemically
deteriorate while in the product.

71

Intel Desktop Board DG41TY Product Guide

Table 19 shows the lead-free board markings as they appear on the board and
accompanying collateral.

Table 19. Lead-Free Board Markings

Description Mark
Lead-Free 2

Interconnect: This symbol

is used to identify electrical
and electronic assemblies and
components in which the lead
(Pb) concentration level in the
Intel Desktop Board substrate
and the solder connections
from the board to the
components (second-level
interconnect) is not greater
than 0.1% by weight (1000
ppm).

nd

Level

or

China
RoHS/Environmentally
Friendly Use Period Logo:

This is an example of the
symbol used on Intel Desktop
Boards and associated
collateral. The color of the
mark may vary depending
upon the application. The
Environmental Friendly Usage
Period (EFUP) for Intel
Desktop Boards has been
determined to be 10 years.

or

72

Regulatory Compliance

EMC Regulations

Intel Desktop Board DG41TY complies with the EMC regulations stated in Table 20
when correctly installed in a compatible host system.

Table 20. EMC Regulations

Regulation Title

FCC 47 CFR Part 15,
Subpart B

ICES-003 Issue 4
(Class B)

EN55022:2006
(Class B)

EN55024:1998 Information Technology Equipment – Immunity Characteristics

EN55022:2006
(Class B)

CISPR 22:2005
+A1:2005 +A2:2006
(Class B)

CISPR 24:1997
+A1:2001 +A2:2002

VCCI V-3/2007.04,
V-4/2007.04, Class B

Japanese Kanji statement translation: This is a Class B product based on the standard
of the Voluntary Control Council for Interference from Information Technology
Equipment (VCCI). If this is used near a radio or television receiver in a domestic
environment, it may cause radio interference. Install and use the equipment
according to the instruction manual.

Title 47 of the Code of Federal Regulations, Part 15, Subpart B,
Radio Frequency Devices. (USA)

Interference-Causing Equipment Standard, Digital Apparatus.
(Canada)

Limits and methods of measurement of Radio Interference
Characteristics of Information Technology Equipment. (European
Union)

Limits and methods of measurement. (European Union)
Australian Communications Authority, Standard for

Electromagnetic Compatibility. (Australia and New Zealand)
Limits and methods of measurement of Radio Disturbance

Characteristics of Information Technology Equipment.
(International)

Information Technology Equipment – Immunity Characteristics –
Limits and Methods of Measurement. (International)

Voluntary Control for Interference by Information Technology
Equipment (Japan)

73

Intel Desktop Board DG41TY Product Guide

Korean Class B statement translation: This is household equipment that is certified to
comply with EMC requirements. You may use this equipment in residential
environments and other non-residential environments.

Ensure Electromagnetic Compatibility (EMC)
Compliance

Before computer integration, make sure that the power supply and other modules or
peripherals, as applicable, have passed Class B EMC testing and are marked
accordingly.

Pay close attention to the following when reading the installation instructions for the
host chassis, power supply, and other modules:

• Product certifications or lack of certifications

• External I/O cable shielding and filtering

• Mounting, grounding, and bonding requirements

• Keying connectors when mating the wrong connectors could be hazardous

If the power supply and other modules or peripherals, as applicable, are not Class B
EMC compliant before integration, then EMC testing may be required on a
representative sample of the newly completed computer.

74

Regulatory Compliance

Product Certifications

Board-Level Certification Markings

Intel Desktop Board DG41TY has the product certification markings shown in Table 21.

Table 21. Product Certification Markings

Description Mark

UL joint US/Canada Recognized Component mark. Includes adjacent
UL file number for Intel Desktop Boards: E210882.

FCC Declaration of Conformity logo mark for Class B equipment.
Includes Intel name and DG41TY model designation.

CE mark. Declaring compliance to European Union (EU) EMC
directive and Low Voltage directive.

Australian Communications Authority (ACA) C-tick mark. Includes
adjacent Intel supplier code number, N-232.

Japan VCCI (Voluntary Control Council for Interference) mark.

KCC (Korean Communications Commission) EMC certification mark.
Includes adjacent KCC certification number: CPU-DG41TY (B).

Taiwan BSMI (Bureau of Standards, Metrology, and Inspections)
mark. Includes adjacent Intel company number, D33025.

Printed wiring board manufacturer’s recognition mark. Consists of a
unique UL recognized manufacturer’s logo, along with a flammability
rating (solder side).

V-0

75

Intel Desktop Board DG41TY Product Guide

Chassis and Component Certifications

Ensure that the chassis and certain components; such as the power supply, peripheral
drives, wiring, and cables; are components certified for the country or market where
used. Agency certification marks on the product are proof of certification. Typical
product certifications include:

In Europe
The CE marking signifies compliance with all applicable European requirements. If the
chassis and other components are not properly CE marked, a supplier’s Declaration of
Conformity statement to the European EMC directive and Low Voltage directive (as
applicable), should be obtained. Additionally, other directives, such as the Radio and
Telecommunications Terminal Equipment (R&TTE) directive may also apply depending
on product features.

In the United States
A certification mark by a Nationally Recognized Testing Laboratory (NRTL) such as UL,
CSA, or ETL signifies compliance with safety requirements. Wiring and cables must
also be UL listed or recognized and suitable for the intended use. The FCC Class B
logo for home or office use signifies compliance with electromagnetic interference
(EMI) requirements.

In Canada
A nationally recognized certification mark such as CSA or cUL signifies compliance with
safety requirements. The Industry Canada statement at the front of this product guide
demonstrates compliance with Canadian EMC regulations.

76