Intel 105BNHU, 6235ANH, 135BNHU, 135BNH, 105BNH User Manual

Intel® Wireless Adapter Information Guide

Supported wireless adapters:

Intel® Centrino® Wireless-N 100 (Available for Windows* 7 only) Intel® Centrino® Wireless-N 105 (Available for Windows* 7 only) Intel® Centrino® Wireless-N 130 (Available for Windows* 7 only) Intel® Centrino® Wireless-N 135 (Available for Windows* 7 only) Intel® WiFi Link 1000 Intel® Centrino® Wireless-N 1030 Intel® Centrino® Wireless-N 2200 (Available for Windows* 7 only) Intel® Centrino® Wireless-N 2230 (Available for Windows* 7 only) Intel® Centrino® Wireless-N + WiMAX 6150 Intel® Centrino® Advanced-N 6200 Intel® Centrino® Advanced-N 6205 Intel® Centrino® Advanced-N 6230 Intel® Centrino® Advanced-N 6235 (Not available for Windows Vista) Intel® Centrino® Advanced-N + WiMAX 6250 Intel® Centrino® Ultimate -N 6300

With your WiFi network card, you can access WiFi networks, share files or printers, or even share your Internet connection. All of these features can be explored using a WiFi network in your home or office. This WiFi network solution is designed for both home and business use. Additional users and features can be added as your networking needs grow and change.

This guide contains basic information about Intel adapters. It includes information about several adapter properties that you can set to control and enhance the performance of your adapter with your particular wireless network and environment. Intel® wireless adapters enable fast connectivity without wires for desktop and notebook PCs.

Adapter Settings Regulatory Information Specifications Important Information Support Warranty Glossary

Depending on the model of your Intel WiFi adapter, your adapter is compatible with 802.11a, 802.11b, 802.11g, and 802.11n (draft 2.0) wireless standards. Operating at 5 GHz or 2.4 GHz frequency at data rates of up to 450 Mbps, you can now connect your computer to existing high-speed networks that use multiple access points within large or small environments. Your WiFi adapter maintains automatic data rate control according to the access point location and signal strength to achieve the fastest possible connection. All of your wireless network connections are easily managed by the WiFi connection utility. Profiles that are set up through the WiFi connection utility provide enhanced security measures with 802.1X network authentication.

Hillsboro, OR 97124-6497 USA

The copying or reproducing of any material in this document in any manner whatsoever without the written permission of Intel Corporation is strictly forbidden. Intel® is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Intel disclaims any proprietary interest in trademarks and trade names other than its own. Microsoft and Windows are registered trademarks of Microsoft Corporation. Windows Vista is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.

*Other names and brands may be claimed as the property of others.

Intel Corporation assumes no responsibility for errors or omissions in this document. Nor does Intel make any commitment to update the information contained herein.

"IMPORTANT NOTICE FOR ALL USERS OR DISTRIBUTORS: Intel wireless LAN adapters are engineered, manufactured, tested, and quality checked to ensure that they meet

all necessary local and governmental regulatory agency requirements for the regions that they are designated and/or marked to ship into. Because wireless LANs are generally unlicensed devices that share spectrum with radars, satellites, and other licensed and unlicensed devices, it is sometimes necessary to dynamically detect, avoid, and limit usage to avoid interference with these devices. In many instances Intel is required to provide test data to prove regional and local compliance to regional and governmental regulations before certification or approval to use the product is granted. Intel's wireless LAN's EEPROM, firmware, and software driver are designed to carefully control parameters that affect radio operation and to ensure electromagnetic compliance (EMC). These parameters include, without limitation, RF power, spectrum usage, channel scanning, and human exposure.

For these reasons Intel cannot permit any manipulation by third parties of the software provided in binary format with the wireless LAN adapters (e.g., the EEPROM and firmware). Furthermore, if you use any patches, utilities, or code with the Intel wireless LAN adapters that have been manipulated by an unauthorized party (i.e., patches, utilities, or code (including open source code modifications) which have not been validated by Intel), (i) you will be solely responsible for ensuring the regulatory compliance of the products, (ii) Intel will bear no liability, under any theory of liability for any issues associated with the modified products, including without limitation, claims under the warranty and/or issues arising from regulatory non- compliance, and (iii) Intel will not provide or be required to assist in providing support to any third parties for such modified products.

Note: Many regulatory agencies consider Wireless LAN adapters to be "modules", and accordingly, condition system-level regulatory approval upon receipt and review of test data documenting that the antennas and system configuration do not cause the EMC and radio operation to be non -compliant."

September 7, 2011

Back to Contents

Adapter Settings

The Advanced tab displays the device properties for the WiFi adapter installed on your computer.

How to Access

At the Intel® PROSet/Wireless WiFi Connection Utility, Advanced Menu click Adapter Settings. Select the Advanced tab.

WiFi Adapter Settings Description

Name Description

802.11n Channel Width (2.4 GHz)

802.11n Channel Width (5.2 GHz)

Set high throughput channel width to maximize performance. Set the channel width to Auto or 20MHz. Use 20MHz if 802.11n channels are restricted. This setting applies to 802.11n capable

adapters only. NOTE: This setting does not apply to the Intel® Wireless WiFi Link 4965AGN (uses 20 MHz

channel width only). Set high throughput channel width to maximize performance. Set the channel width to Auto or

20MHz. Use 20MHz if 802.11n channels are restricted. This setting applies to 802.11n capable adapters only.

NOTE: This setting does not apply to the following adapters:

Intel® WiFi Link 1000 Intel® Wireless WiFi Link 4965AGN

802.11n Mode The 802.11n standard builds on previous 802.11 standards by adding multiple - input multipleoutput (MIMO). MIMO increases data throughput to improve transfer rate. Select Enabled or Disabled to set the 802.11n mode of the WiFi adapter. Enabled is the default setting. This setting applies to 802.11n capable adapters only.

NOTE: To achieve transfer rates greater than 54 Mbps on 802.11n connections, WPA2*-AES security must be selected. No security ( None) can be selected to enable network setup and troubleshooting.

An administrator can enable or disable support for high throughput mode to reduce powerconsumption or conflicts with other bands or compatibility issues.

Ad Hoc Channel

Unless the other computers in the ad hoc network use a different channel from the default channel, there is no need to change the channel.

Value: Select the permitted operating channel from the list.

802.11b/g: Select this option when 802.11b and 802.11g (2.4 GHz) ad hoc band

frequency is used.

802.11a: Select this option when 802.11a (5 GHz) ad hoc band frequency is used. This setting does not apply to the Intel® WiFi Link 1000 adapter.

Ad Hoc Power Management

NOTE: When an 802.11a channel is not displayed, initiating ad hoc networks is not supported

for 802.11a channels. Set power saving features for device to device (ad hoc) networks.

Disable: Select when connecting to ad hoc networks that contain stations that do not support ad hoc power management

Maximum Power Savings: Select to optimize battery life.

Noisy Environment: Select to optimize performance or connecting with multiple clients.

Ad Hoc QoS Mode

Fat Channel Intolerant

Mixed mode protection

Power Management

Quality of Service (QoS) control in ad hoc networks. QoS provides prioritization of traffic from the access point over a wireless LAN based on traffic classification. WMM (Wi - Fi Multimedia) is the QoS certification of the Wi -Fi Alliance (WFA). When WMM is enabled, the WiFi adapter uses WMM to support priority tagging and queuing capabilities for Wi -Fi networks.

WMM Enabled (Default) WMM Disabled

This setting communicates to surrounding networks that this WiFi adapter is not tolerant of 40MHz channels in the 2.4GHz band. The default setting is for this to be turned off (disabled), so that the adapter does not send this notification.

NOTE: This setting does not apply to the following adapters:

Intel® Wireless WiFi Link 4965AG_ Intel® PRO/Wireless 3945ABG Network Connection

Use to avoid data collisions in a mixed 802.11b and 802.11g environment. Request to Send/Clear to Send (RTS/CTS) should be used in an environment where clients may not hear each other. CTS-to-self can be used to gain more throughput in an environment where clients are in close proximity and can hear each other.

Lets you select a balance between power consumption and WiFi adapter performance. The WiFi adapter power settings slider sets a balance between the computer's power source and the battery.

Roaming Aggressiveness

Throughput Enhancement

Transmit Power

Use default value: (Default) Power settings are based on the computer's power source. Manual: Adjust the slider for the desired setting. Use the lowest setting for maximum

battery life. Use the highest setting for maximum performance.

NOTE: Power consumption savings vary based on Network (Infrastructure) settings. This setting lets you define how aggressively your wireless client roams to improve connection

to an access point.

Default: Balanced setting between not roaming and performance. Lowest: Your wireless client will not roam. Only significant link quality degradation

causes it to roam to another access point. Highest: Your wireless client continuously tracks the link quality. If any degradation occurs, it tries to find and roam to a better access point.

Changes the value of the Packet Burst Control.

Enable: Select to enable throughput enhancement. Disable: (Default) Select to disable throughput enhancement.

Default Setting: Highest power setting. Lowest: Minimum Coverage: Set the adapter to the lowest transmit power. Enables you to

expand the number of coverage areas or confine a coverage area. Reduces the coverage area in high traffic areas to improve overall transmission quality and avoids congestion and interference with other devices.

Highest: Maximum Coverage: Set the adapter to a maximum transmit power level. Select for maximum performance and range in environments with limited additional WiFi radio devices.

NOTE: The optimal setting is for a user to always set the transmit power at the lowest possible level that is still compatible with the quality of their communication. This allows the maximum number of wireless devices to operate in dense areas and reduce interference with other devices that it shares the same radio spectrum with.

NOTE: This setting takes effect when either Network (Infrastructure) or Device to Device (ad hoc) mode is used.

Wireless Mode Select which mode to use for connection to a wireless network:

802.11a only: Connect the wireless WiFi adapter to 802.11a networks only. Not

applicable for all adapters.

802.11b only: Connect the wireless WiFi adapter to 802.11b networks only. Not applicable for all adapters.

802.11g only: Connect the wireless WiFi adapter to 802.11g networks only.

802.11a and 802.11g: Connect the WiFi adapter to 802.11a and 802.11g networks

only. Not applicable for all adapters.

802.11b and 802.11g: Connect the WiFi adapter to 802.11b and 802.11g networks only. Not applicable for all adapters.

802.11a, 802.11b, and 802.11g: (Default) - Connect to either 802.11a, 802.11b or

802.11g wireless networks. Not applicable for all adapters.

NOTE: These wireless modes (Modulation type) determine the discovered access points displayed in the WiFi Networks list

OK Saves settings and returns to the previous page. Cancel Closes and cancels any changes.

Back to Top Back to Contents

Trademarks and Disclaimers

Back to Contents

Regulatory Information

NOTE: Due to the evolving state of regulations and standards in the wireless LAN field (IEEE 802.11

and similar standards), the information provided herein is subject to change. Intel Corporation assumes no responsibility for errors or omissions in this document.

Intel® Centrino® Wireless-N 100 Intel® Centrino® Wireless-N 105 Intel® Centrino® Wireless-N 130 Intel® Centrino® Wireless-N 135 Intel® WiFi Link 1000 Intel® Centrino® Wireless-N 1030 Intel® Centrino® Wireless-N 2200 Intel® Centrino® Wireless-N 2230 Intel® Centrino® Wireless-N + WiMAX 6150 Intel® Centrino® Advanced-N 6200 Intel® Centrino® Advanced-N 6205 Intel® Centrino® Advanced-N 6230 Intel® Centrino® Advanced-N 6235 Intel® Centrino® Advanced-N + WiMAX 6250 Intel® Centrino® Ultimate -N 6300

Intel WiFi/WiMAX Wireless Adapters

Information in this section supports the following wireless adapters:

Intel® Centrino® Wireless-N + WiMAX 6150 Intel® Centrino® Advanced-N + WiMAX 6250

Specifications for complete wireless adapter specifications.

See

NOTE: In this section, all references to the "wireless adapter" refer to all adapters listed above.

The following information is provided:

Information for the User Regulatory Information

Information for the User

Safety Notices

USA—FCC and FAA

The FCC with its action in ET Docket 96 -8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment. The wireless adapter meets the Human Exposure limits found in OET Bulletin 65, supplement C, 2001, and ANSI/IEEE C95.1, 1992. Proper operation of this radio according to the instructions found in this manual will result in exposure substantially below the FCC’s recommended limits.

The following safety precautions should be observed:

Do not touch or move antenna while the unit is transmitting or receiving. Do not hold any component containing the radio such that the antenna is very close or touching any exposed parts of the body, especially the face or eyes, while transmitting. Do not operate the radio or attempt to transmit data unless the antenna is connected; this behavior may

cause damage to the radio. Use in specific environments:

The use of wireless adapters in hazardous locations is limited by the constraints posed by the safety directors of such environments. The use of wireless adapters on airplanes is governed by the Federal Aviation Administration (FAA). The use of wireless adapters in hospitals is restricted to the limits set forth by each hospital.

Antenna Use

In order to comply with FCC RF exposure limits, low gain integrated antennas should be located at a minimum distance of 20cm (8 inches) or more from the body of all persons or at a minimum distance as specified by the FCC module grant conditions. FCC grants can be viewed from the FCC Equipment Authorization website at

https://fjallfoss.fcc.gov/oetcf/eas/reports/GenericSearch.cfm by entering the FCC ID printed on the module label.

Explosive Device Proximity Warning

Warning: Do not operate a portable transmitter (including this wireless adapter) near unshielded blasting

caps or in an explosive environment unless the transmitter has been modified to be qualified for such use.

Antenna Warnings

Warning: To comply with the FCC and ANSI C95.1 RF exposure limits, it is recommended that for the wireless adapter installed in a desktop or portable computer, the antenna for this wireless adapter to be installed so as to provide a separation distance of at least 20 cm (8 inches) from all persons or at the minimum distance as specified by the module grant conditions. FCC grants can be viewed from the FCC Equipment Authorization website

https://fjallfoss.fcc.gov/oetcf/eas/reports/GenericSearch.cfm by entering the FCC ID printed on the module

at label.

Warning: The wireless adapter is not designed for use with high-gain directional antennas.

Use On Aircraft Caution

Caution: Regulations of the FCC and FAA prohibit airborne operation of radio-frequency wireless devices

(wireless adapters) because their signals could interfere with critical aircraft instruments.

Other Wireless Devices

Safety Notices for Other Devices in the Wireless Network: See the documentation supplied with wireless

adapters or other devices in the wireless network.

Local Restrictions on 802.11a, 802.11b, 802.11g, 802.11n, and 802.16e Radio Usage

Caution: Due to the fact that the frequencies used by 802.11a, 802.11b, 802.11g, 802.11n, and 802.16e

wireless LAN devices may not yet be harmonized in all countries, 802.11a, 802.11b, 802.11g, 802.11n, and

802.16e products are designed for use only in specific countries, and are not allowed to be operated in countries other than those of designated use. As a user of these products, you are responsible for ensuring that the products are used only in the countries for which they were intended and for verifying that they are configured with the correct selection of frequency and channel for the country of use. The device transmit power control (TPC) interface is part of the Intel® PROSet/Wireless WiFi Connection Utility Software. Operational restrictions for Equivalent Isotropic Radiated Power (EIRP) are provided by the system manufacturer. Any deviation from the permissible power and frequency settings for the country of use is an infringement of national law and may be punished as such.

For country-specific information, see the additional compliance information supplied with the product.

Wireless Interoperability

The wireless adapter is designed to be interoperable with other wireless LAN products that are based on direct

sequence spread spectrum (DSSS) radio technology and to comply with the following standards:

IEEE Std. 802.11b compliant Standard on Wireless LAN IEEE Std. 802.11g compliant Standard on Wireless LAN IEEE Std. 802.11a compliant Standard on Wireless LAN IEEE Std. 802.11n draft 2.0 compliant on Wireless LAN IEEE 802.16e -2005 Wave 2 compliant Wireless Fidelity certification, as defined by the Wi-Fi Alliance WiMAX certification as defined by the WiMAX Forum

The Wireless Adapter and Your Health

The wireless adapter, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by the wireless adapter, however, is less than the electromagnetic energy emitted by other wireless devices such as mobile phones. The wireless adapter operates within the guidelines found in radio frequency safety standards and recommendations. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of the wireless adapter may be restricted by the proprietor of the building or responsible representatives of the applicable organization. Examples of such situations may include:

Using the wireless adapter on board airplanes, or Using the wireless adapter in any other environment where the risk of interference with other devices or services is perceived or identified as being harmful.

If you are uncertain of the policy that applies to the use of wireless adapters in a specific organization or environment (an airport, for example), you are encouraged to ask for authorization to use the adapter before you turn it on.

WEEE

Regulatory Information

Information for the OEMs and Integrators

The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user.

This device is intended for OEM integrators only. Please see the full Grant of Equipment document for other restrictions. This device must be operated and used with a locally approved access point.

Information To Be Supplied to the End User by the OEM or Integrator

The following regulatory and safety notices must be published in documentation supplied to the end user of the product or system incorporating the Intel® wireless adapter, in compliance with local regulations. Host system must be labeled with "Contains FCC ID: XXXXXXXX", FCC ID displayed on label.

The Intel® wireless adapter must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Intel Corporation is not responsible for any radio or television interference caused by unauthorized modification of the devices included with the wireless adapter kit or the substitution or attachment of connecting cables and equipment other than that specified by Intel Corporation. The correction of interference caused by such unauthorized modification, substitution or attachment is

the responsibility of the user. Intel Corporation and authorized resellers or distributors are not liable for any damage or violation of government regulations that may arise from the user failing to comply with these guidelines.

Local Restriction of 802.11a, 802.11b, 802.11g, and 802.11n Radio Usage

The following statement on local restrictions must be published as part of the compliance documentation for all

802.11a, 802.11b, 802.11g and 802.11n products.

Caution: Due to the fact that the frequencies used by 802.11a, 802.11b, 802.11g, 802.11n, and 802.16e

wireless LAN devices may not yet be harmonized in all countries, 802.11a, 802.11b, 802.11g, 802.11n, and

802.16e products are designed for use only in specific countries, and are not allowed to be operated in countries other than those of designated use. As a user of these products, you are responsible for ensuring that the products are used only in the countries for which they were intended and for verifying that they are configured with the correct selection of frequency and channel for the country of use. Any deviation from the permissible power and frequency settings for the country of use is an infringement of national law and may be punished as such.

FCC Radio Frequency Interference Requirements

This wireless adapter is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range. FCC requires this wireless adapter to be used indoors for the frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interference to co-channel mobile satellite systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and /or damage this device.

This wireless adapter is intended for OEM integrators only. This wireless adapter cannot be co -located with any other transmitter unless approved by the FCC.

USA—Federal Communications Commission (FCC)

This wireless adapter complies with Part 15 of the FCC Rules. Operation of the device is subject to the following two conditions:

This device may not cause harmful interference. This device must accept any interference that may cause undesired operation.

NOTE: The radiated output power of the adapter is far below the FCC radio frequency exposure limits. Nevertheless, the adapter should be used in such a manner that the potential for human contact during normal operation is minimized. To avoid the possibility of exceeding the FCC radio frequency exposure limits, you should keep a distance of at least 20cm between you (or any other person in the vicinity), or the minimum separation distance as specified by the FCC grant conditions, and the antenna that is built into the computer. Details of the authorized configurations can be found at

http://www.fcc.gov/oet/ea/

Interference Statement

This wireless adapter has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This wireless adapter generates, uses, and can radiate radio frequency energy. If the wireless adapter is not installed and used in accordance with the instructions, the wireless adapter may cause harmful interference to radio communications. There is no guarantee, however, that such interference will not occur in a particular installation. If this wireless adapter does cause harmful interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by taking one or more of the following measures:

by entering the FCC ID number on the device.

Reorient or relocate the receiving antenna of the equipment experiencing the interference. Increase the distance between the wireless adapter and the equipment experiencing the interference. Connect the computer with the wireless adapter to an outlet on a circuit different from that to which the equipment experiencing the interference is connected.

Consult the dealer or an experienced radio/TV technician for help. NOTE: The adapter must be installed and used in strict accordance with the manufacturer's

instructions as described in the user documentation that comes with the product. Any other installation or use will violate FCC Part 15 regulations.

Underwriters Laboratories Inc. (UL) Regulatory Warning

For use in (or with) UL Listed personal computers or compatible.

Low Halogen

Applies only to brominated and chlorinated flame retardants (BFRs/CFRs) and PVC in the final product. Intel components as well as purchased components on the finished assembly meet JS -709 requirements, and the PCB / substrate meet IEC 61249 -2-21 requirements. The replacement of halogenated flame retardants and/or PVC may not be better for the environment.

Taiwan

Radio Approvals

To determine whether you are allowed to use your wireless network device in a specific country, please check to see if the radio type number that is printed on the identification label of your device is listed in the manufacturer's OEM Regulatory Guidance document.

Regulatory Markings

A list of required regulatory markings can be found on the web at http://www.intel.com/support/wireless/wlan/ To find the regulatory information for your adapter, click on the link for your adapter. Then click Additional

Information > Regulatory Documents.

Intel WiFi Adapters, 802.11n Compliant

The information in this section applies to the following products:

Intel® Centrino® Wireless-N 100 Intel® Centrino® Wireless-N 105 Intel® Centrino® Wireless-N 130 Intel® Centrino® Wireless-N 135 Intel® WiFi Link 1000 Intel® Centrino® Wireless-N 1030 Intel® Centrino® Wireless-N 2200 Intel® Centrino® Wireless-N 2230 Intel® Centrino® Advanced-N 6200

Intel® Centrino® Advanced-N 6205 Intel® Centrino® Advanced-N 6230 Intel® Centrino® Advanced-N 6235 Intel® Centrino® Ultimate -N 6300

Specifications for wireless adapter specifications.

See

NOTE: In this section, all references to the "wireless adapter" refer to all adapters listed above.

The following information is provided:

Information for the User Regulatory Information

Information for the User

Safety Notices

USA—FCC and FAA

The FCC with its action in ET Docket 96 -8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment. The wireless adapter meets the Human Exposure limits found in OET Bulletin 65, supplement C, 2001, and ANSI/IEEE C95.1, 1992. Proper operation of this radio according to the instructions found in this manual will result in exposure substantially below the FCC’s recommended limits.

The following safety precautions should be observed:

Do not touch or move antenna while the unit is transmitting or receiving. Do not hold any component containing the radio such that the antenna is very close or touching any exposed parts of the body, especially the face or eyes, while transmitting. Do not operate the radio or attempt to transmit data unless the antenna is connected; this behavior may cause damage to the radio. Use in specific environments:

The use of wireless adapters in hazardous locations is limited by the constraints posed by the safety directors of such environments. The use of wireless adapters on airplanes is governed by the Federal Aviation Administration (FAA). The use of wireless adapters in hospitals is restricted to the limits set forth by each hospital.

Antenna Use

In order to comply with FCC RF exposure limits, low gain integrated antennas should be located at a minimum distance of 20cm (8 inches) or more from the body of all persons or at a minimum distance as specified by the FCC module grant conditions. FCC grants can be viewed from the FCC Equipment Authorization website at

https://fjallfoss.fcc.gov/oetcf/eas/reports/GenericSearch.cfm by entering the FCC ID printed on the module label.

Explosive Device Proximity Warning

Warning: Do not operate a portable transmitter (including this wireless adapter) near unshielded blasting

caps or in an explosive environment unless the transmitter has been modified to be qualified for such use.

Antenna Warnings

Warning: To comply with the FCC and ANSI C95.1 RF exposure limits, it is recommended that for the wireless adapter installed in a desktop or portable computer, the antenna for this wireless adapter to be installed so as to provide a separation distance of at least 20 cm (8 inches) from all persons or at the minimum distance as specified by the module grant conditions. FCC grants can be viewed from the FCC Equipment Authorization website

https://fjallfoss.fcc.gov/oetcf/eas/reports/GenericSearch.cfm by entering the FCC ID printed on the module

at label.

Warning: The wireless adapter is not designed for use with high-gain directional antennas.

Use On Aircraft Caution

Caution: Regulations of the FCC and FAA prohibit airborne operation of radio-frequency wireless devices

(wireless adapters) because their signals could interfere with critical aircraft instruments.

Other Wireless Devices

Safety Notices for Other Devices in the Wireless Network: See the documentation supplied with wireless

adapters or other devices in the wireless network.

Local Restrictions on 802.11a, 802.11b, 802.11g and 802.11n Radio Usage

Caution: Due to the fact that the frequencies used by 802.11a, 802.11b, 802.11g and 802.11n wireless LAN devices may not yet be harmonized in all countries, 802.11a, 802.11b, 802.11g and 802.11n products are designed for use only in specific countries, and are not allowed to be operated in countries other than those of designated use. As a user of these products, you are responsible for ensuring that the products are used only in the countries for which they were intended and for verifying that they are configured with the correct selection of frequency and channel for the country of use. The device transmit power control (TPC) interface is part of the Intel® PROSet/Wireless WiFi Connection Utility Software. Operational restrictions for Equivalent Isotropic Radiated Power (EIRP) are provided by the system manufacturer. Any deviation from the permissible power and frequency settings for the country of use is an infringement of national law and may be punished as such.

For country-specific information, see the additional compliance information supplied with the product.

Wireless Interoperability

The wireless adapter is designed to be interoperable with other wireless LAN products that are based on direct sequence spread spectrum (DSSS) radio technology and to comply with the following standards:

IEEE Std. 802.11b compliant Standard on Wireless LAN IEEE Std. 802.11g compliant Standard on Wireless LAN IEEE Std. 802.11a compliant Standard on Wireless LAN IEEE Std. 802.11n draft 2.0 compliant on Wireless LAN Wireless Fidelity certification, as defined by the Wi-Fi Alliance

The Wireless Adapter and Your Health

The wireless adapter, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by the wireless adapter, however, is less than the electromagnetic energy emitted by other wireless devices such as mobile phones. The wireless adapter operates within the guidelines found in radio frequency safety standards and recommendations. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of the wireless adapter may be restricted by the proprietor of the building or responsible representatives of the applicable organization. Examples of such situations may include:

Using the wireless adapter on board airplanes, or Using the wireless adapter in any other environment where the risk of interference with other devices or services is perceived or identified as being harmful.

If you are uncertain of the policy that applies to the use of wireless adapters in a specific organization or environment (an airport, for example), you are encouraged to ask for authorization to use the adapter before you turn it on.

WEEE

Regulatory Information

Information for the OEMs and Integrators

The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user.

This device is intended for OEM integrators only. Please see the full Grant of Equipment document for other restrictions. This device must be operated and used with a locally approved access point.

Information To Be Supplied to the End User by the OEM or Integrator

The following regulatory and safety notices must be published in documentation supplied to the end user of the product or system incorporating the Intel® wireless adapter, in compliance with local regulations. Host system must be labeled with "Contains FCC ID: XXXXXXXX", FCC ID displayed on label.

The wireless adapter must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. For country -specific approvals, see Radio

Approvals. Intel Corporation is not responsible for any radio or television interference caused by unauthorized

modification of the devices included with the wireless adapter kit or the substitution or attachment of connecting cables and equipment other than that specified by Intel Corporation. The correction of interference caused by such unauthorized modification, substitution or attachment is the responsibility of the user. Intel Corporation and authorized resellers or distributors are not liable for any damage or violation of government regulations that may arise from the user failing to comply with these guidelines.

Local Restriction of 802.11a, 802.11b, 802.11g, and 802.11n Radio Usage

The following statement on local restrictions must be published as part of the compliance documentation for all

802.11a, 802.11b, 802.11g and 802.11n products.

Caution: Due to the fact that the frequencies used by 802.11a, 802.11b, 802.11g and 802.11n wireless LAN devices may not yet be harmonized in all countries, 802.11a, 802.11b, 802.11g and 802.11n products are designed for use only in specific countries, and are not allowed to be operated in countries other than those of designated use. As a user of these products, you are responsible for ensuring that the products are used only in the countries for which they were intended and for verifying that they are configured with the correct selection of frequency and channel for the country of use. Any deviation from permissible settings and restrictions in the country of use could be an infringement of national law and may be punished as such.

FCC Radio Frequency Interference Requirements

This device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz and 5.470 to 5.725 GHz frequency ranges. FCC requires this product to be used indoors for the frequency ranges 5.15 to 5.25 GHz and

5.470 to 5.725 GHz to reduce the potential for harmful interference to co-channel mobile satellite systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and /or damage this device. No configuration controls are provided for this wireless adapter allowing any change in the frequency of operations outside the FCC grant of authorization for U.S operation according to Part 15.407 of the FCC rules.

This device is intended for OEM integrators only. This device cannot be co -located with any other transmitter unless approved by the FCC.

USA—Federal Communications Commission (FCC)

This device complies with Part 15 of the FCC Rules. Operation of the device is subject to the following two conditions:

This device may not cause harmful interference. This device must accept any interference that may cause undesired operation.

NOTE: The radiated output power of the adapter is far below the FCC radio frequency exposure limits. Nevertheless, the adapter should be used in such a manner that the potential for human contact during normal operation is minimized. To avoid the possibility of exceeding the FCC radio frequency exposure limits, you should keep a distance of at least 20cm between you (or any other person in the vicinity), or the minimum separation distance as specified by the FCC grant conditions, and the antenna that is built into the computer. Details of the authorized configurations can be found at

http://www.fcc.gov/oet/ea/

Interference Statement

This wireless adapter has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This wireless adapter generates, uses, and can radiate radio frequency energy. If the wireless adapter is not installed and used in accordance with the instructions, the wireless adapter may cause harmful interference to radio communications. There is no guarantee, however, that such interference will not occur in a particular installation. If this wireless adapter does cause harmful interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by taking one or more of the following measures:

by entering the FCC ID number on the device.

Reorient or relocate the receiving antenna of the equipment experiencing the interference. Increase the distance between the wireless adapter and the equipment experiencing the interference. Connect the computer with the wireless adapter to an outlet on a circuit different from that to which the equipment experiencing the interference is connected. Consult the dealer or an experienced radio/TV technician for help.

NOTE: The adapter must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Any other installation or use will violate FCC Part 15 regulations.

Underwriters Laboratories Inc. (UL) Regulatory Warning

For use in (or with) UL Listed personal computers or compatible.

Low Halogen

Applies only to brominated and chlorinated flame retardants (BFRs/CFRs) and PVC in the final product. Intel components as well as purchased components on the finished assembly meet JS -709 requirements, and the PCB / substrate meet IEC 61249 -2-21 requirements. The replacement of halogenated flame retardants and/or PVC may not be better for the environment.

Canada – Industry Canada (IC)

This device complies with RSS210 of Industry Canada. Cet appareil se conforme à RSS210 de Canada d'Industrie. Caution: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use due to its operation in

the 5.15 - to 5.25-GHz frequency range. Industry Canada requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel mobile satellite systems. High power radar is allocated as the primary user of the 5.25- to 5.35- GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage to this device. The maximum allowed antenna gain for use with this device is 6dBi in order to comply with the E.I.R.P limit for the 5.25 - to 5.35 and

5.725 to 5.85 GHz frequency range in point-to-point operation. To comply with RF exposure requirements all antennas should be located at a minimum distance of 20cm, or the minimum separation distance allowed by the module approval, from the body of all persons.

Attention: l’utilisation d’un réseau sans fil IEEE802.11a est réstreinte à une utilisation en intérieur à cause du fonctionement dans la bande de fréquence 5.15 -5.25 GHz. Industry Canada requiert que ce produit soit utilisé à l’intérieur des bâtiments pour la bande de fréquence 5.15 -5.25 GHz afin de réduire les possibilités d’interférences nuisibles aux canaux co -existants des systèmes de transmission satellites. Les radars de puissances ont fait l’objet d’une allocation primaire de fréquences dans les bandes 5.25-5.35 GHz et 5.65 -5.85 GHz. Ces stations radar peuvent créer des interférences avec ce produit et/ou lui être nuisible. Le gain d’antenne maximum permissible pour une utilisation avec ce produit est de 6 dBi afin d’être conforme aux limites de puissance isotropique rayonnée équivalente (P.I.R.E.) applicable dans les bandes 5.25-5.35 GHz et 5.725-5.85 GHz en fonctionement point-à-point. Se pour conformer aux conditions d'exposition de RF toutes les antennes devraient être localisées à une distance minimum de 20 cm, ou la distance de séparation minimum permise par l'approbation de module, du corps de toutes les personnes.”

This Class B digital apparatus complies with Canadian ICES- 003. Cet appareil numérique de la classe B est conforme a la norme NMB-003 du Canada.

European Union

The low band 5.15 - 5.35 GHz is for indoor use only. This equipment complies with the essential requirements of the European Union directive 1999/5/EC. See

Statements of European Union Compliance.

European Union Declarations of Conformity

The European Union Declaration of Conformity for each adapter is available at:

http://www.intel.com/support/wireless/wlan/.

To find the Declaration of Conformity for your adapter, click on the link for your adapter. Then click Additional

Information > Regulatory Documents.

Japan

Indoor use only in the 5Ghz band.

Korea

Morocco

The operation of this product in the radio channel 2 (2417 MHz) is not authorized in the following cities: Agadir, Assa-Zag, Cabo Negro, Chaouen, Goulmima, Oujda, Tan Tan, Taourirt, Taroudant and Taza.

The operation of this product in the radio channels 4, 5, 6 et 7 (2425 - 2442 MHz) is not authorized in the following cities: Aéroport Mohamed V, Agadir, Aguelmous, Anza, Benslimane, Béni Hafida, Cabo Negro, Casablanca, Fès, Lakbab, Marrakech, Merchich, Mohammédia, Rabat, Salé, Tanger, Tan Tan, Taounate, Tit Mellil, Zag.

Taiwan

Radio Approvals

To determine whether you are allowed to use your wireless network device in a specific country, please check to see if the radio type number that is printed on the identification label of your device is listed in the manufacturer's OEM Regulatory Guidance document.

Regulatory Markings

A list of required regulatory markings can be found on the web at http://www.intel.com/support/wireless/wlan/ To find the regulatory information for your adapter, click on the link for your adapter. Then click Additional

Information > Regulatory Documents.

Statement of European Compliance

Each of the adapters listed below comply with the essential requirements of the European Union directive 1999/5/EC.

Intel® Centrino® Wireless-N 100 (Only available on Windows* 7 installations) Intel® Centrino® Wireless-N 105 (Only available on Windows* 7 installations) Intel® Centrino® Wireless-N 130 (Only available on Windows* 7 installations) Intel® Centrino® Wireless-N 135 (Only available on Windows* 7 installations) Intel® WiFi Link 1000 Intel® Centrino® Wireless-N 1030 Intel® Centrino® Wireless-N 2200 (Only available on Windows* 7 installations) Intel® Centrino® Wireless-N 2230 (Not available on Windows* Vista* installations) Intel® Centrino® Wireless-N + WiMAX 6150 Intel® Centrino® Advanced-N 6200 Intel® Centrino® Advanced-N 6205 Intel® Centrino® Advanced-N 6230 Intel® Centrino® Advanced-N 6235 Intel® Centrino® Advanced-N + WiMAX 6250 Intel® Centrino® Ultimate -N 6300

Back to Top Back to Contents

Trademarks and Disclaimers

Back to Contents

Specifications

Intel® Centrino® Wireless-N 100 Intel® Centrino® Wireless-N 105 Intel® Centrino® Wireless-N 130 Intel® Centrino® Wireless-N 135 Intel® WiFi Link 1000 Intel® Centrino® Wireless-N 1030 Intel® Centrino® Wireless-N 2200 Intel® Centrino® Wireless-N 2230 Intel® Centrino® Wireless-N + WiMAX 6150 Intel® Centrino® Advanced-N 6200 Intel® Centrino® Advanced-N 6205 Intel® Centrino® Advanced-N 6230 Intel® Centrino® Advanced-N 6235 Intel® Centrino® Advanced-N + WiMAX 6250 Intel® Centrino® Ultimate -N 6300

Intel® Centrino® Wireless-N 100, Intel® Centrino® Wireless-N 105, Intel® Centrino® Wireless-N 130 and Intel® Centrino® Wireless-N 135

Form Factor PCI Express* Half-Mini Card Dimensions Half-Mini Card: Width 1.049 in x Length 1.18 in x Height 0.18 in (26.64 mm x 30 mm x 4.5

mm)

Antenna Interface Connector

Antenna Diversity On-board diversity Connector

Interface Voltage 3.3 V Operating

Temperature Humidity 50% to 95% non - condensing (at temperatures of 25 ºC to 35 ºC) WiFi Frequency

Modulation Frequency band 2.400 - 2.4835 GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM CCK, DQPSK, DBPSK Wireless Medium 2.4 GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) Channels All channels as defined by the relevant specification and country rules. IEEE 802.11n Data

Rates

IEEE 802.11g Data Rates

IEEE 802.11b Data 11, 5.5, 2, 1 Mbps

Hirose U.FL-R-SMT mates with cable connector U.FL-LP - 066

52-pin Mini Card edge connector

0 to +80 degrees Celsius

2.4 GHz (802.11b/g/n)

MIMO Configuration: 1X1 Tx/Rx: 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30,

28.9, 21.7, 15, 14.4, 7.2 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps

Rates Bluetooth Support

General

Operating Systems Windows* 7 (32-bit and 64-bit) Wi-Fi Alliance*

certification Cisco Compatible

Extensions certification

IEEE Feature Sets IEEE 802.11b, 802.11g, 802.11n, 802.11e, 802.11i, 802.11d, 802.11h Architecture Infrastructure or ad hoc (peer-to -peer) operating modes Security WPA-Personal, WPA2-Personal, WPA -Enterprise, WPA2-Enterprise, AES-CCMP 128 -bit, WEP

Product Safety UL, C-UL, CB (IEC 60590)

Wi-Fi* certification for 802.11b, 802.11g, 802.11n, WPA-Personal, WPA-Enterprise, WPA2Personal, WPA2 -Enterprise, WMM, WPS

Cisco Compatible Extensions, v4.0

128-bit and 64-bit; 802.1X: EAP -SIM, LEAP, PEAP, TKIP, EAP-FAST, EAP-TLS, EAP- TTLS, EAP-AKA

Intel® Centrino® Wireless-N 100: None Intel® Centrino® Wireless-N 105: None Intel® Centrino® Wireless-N 130: Bluetooth 2.1, 2.1 + EDR, 3.0, 3.0+HS Intel® Centrino® Wireless-N 135: Bluetooth 4.0 (Bluetooth Low-Energy and Bluetooth

3.0 +HS)

Intel® WiFi Link 1000

WiFi / WiMAX

Form Factor PCI Express* Mini Card and Half-Mini Card SKUs Intel® WiFi Link 1000 - 1X2 MC/HMC Dimensions Mini Card: Width 2.0 in x Length 1.18 in x Height 0.18 in (50.80 mm x 30 mm x 4.5

mm) Half-Mini Card: Width 1.049 in x Length 1.18 in x Height 0.18 in (26.64 mm x 30 mm

x 4.5 mm)

Antenna Interface Connector

Antenna Diversity On-board diversity Connector Interface 52 - pin Mini Card edge connector Voltage 3.3 V Operating Temperature 0 to +80 degrees Celsius Humidity 50% to 90% non - condensing (at temperatures of 25 ºC to 35 ºC)

WiFi

Frequency Modulation 2.4 GHz (802.11b/g/n) Frequency band 2.41-2.474 GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM, CCK, DQPSK, DBPSK Wireless Medium 2.4 GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) Channels All channels as defined by the relevant specification and country rules. IEEE 802.11n Data

Rates IEEE 802.11g Data

Rates IEEE 802.11b Data 11, 5.5, 2, 1 Mbps

Hirose U.FL-R-SMT mates with cable connector U.FL-LP - 066

300, 270, 243, 240, 180, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 Mbps

54, 48, 36, 24, 18, 12, 9, 6 Mbps

Rates

WiFi General

Operating Systems Microsoft Windows* XP (32 and 64 bit) and Windows Vista* (32 and 64 bit), Ubuntu

Linux*

Wi-Fi Alliance* certification

Cisco Compatible Extensions certification

WLAN Standard IEEE 802.11g, 802.11b, 802.11n, 802.11d, 802.11e, 802.11i, Architecture Infrastructure or ad hoc (peer-to -peer) operating modes Security WPA-Personal, WPA2-Personal, WPA -Enterprise, WPA2-Enterprise, 802.1X: EAP-SIM,

Encryption AES-CCMP 128-bit, WEP 128-bit and 64-bit, CKIP, TKIP Product Safety UL, C-UL, CB (IEC 60590)

Wi-Fi* certification for 802.11b, 802.11g, 802.11n, WPA-Personal, WPA-Enterprise, WPA2-Personal, WPA2- Enterprise, WMM, WPS

Cisco Compatible Extensions, v4.0

LEAP, PEAP, EAP-FAST, EAP-TLS, EAP-TTLS, EAP -AKA

Intel® Centrino® Wireless-N 2200 and Intel® Centrino® Wireless-N 2230

Form Factor PCI Express* Half-Mini Card Dimensions Half-Mini Card: Width 1.049 in x Length 1.18 in x Height 0.18 in (26.64 mm x 30 mm x 4.5

mm)

Antenna Interface Connector

Antenna Diversity On-board diversity Connector

Interface Voltage 3.3 V Operating

Temperature Humidity 50% to 95% non - condensing (at temperatures of 25 ºC to 35 ºC) WiFi Frequency

Modulation Frequency band 2.400 - 2.4835 GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM CCK, DQPSK, DBPSK Wireless Medium 2.4 GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) Channels All channels as defined by the relevant specification and country rules. IEEE 802.11n Data

Rates

IEEE 802.11g Data Rates

IEEE 802.11b Data Rates

Bluetooth Support

Hirose U.FL-R-SMT mates with cable connector U.FL-LP - 066

52-pin Mini Card edge connector

0 to +80 degrees Celsius

2.4 GHz (802.11b/g/n)

MIMO Configuration: 2X2 Tx/Rx: 300, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45,

43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps

11, 5.5, 2, 1 Mbps

Intel® Centrino® Wireless-N 2200: None Intel® Centrino® Wireless-N 2230: Bluetooth 4.0 (Bluetooth Low- Energy and Bluetooth 3.0 +HS)

General

Operating Systems Windows* 7 (32-bit and 64-bit) Wi-Fi Alliance*

certification Cisco Compatible

Extensions certification

IEEE Feature Sets IEEE 802.11b, 802.11g, 802.11n, 802.11e, 802.11i, 802.11d, 802.11h Architecture Infrastructure or ad hoc (peer-to -peer) operating modes Security WPA-Personal, WPA2-Personal, WPA -Enterprise, WPA2-Enterprise, AES-CCMP 128 -bit, WEP

Product Safety UL, C-UL, CB (IEC 60590)

Wi-Fi* certification for 802.11b, 802.11g, 802.11n, WPA-Personal, WPA-Enterprise, WPA2Personal, WPA2 -Enterprise, WMM, WPS

Cisco Compatible Extensions, v4.0

128-bit and 64-bit; 802.1X: EAP -SIM, LEAP, PEAP, TKIP, EAP-FAST, EAP-TLS, EAP- TTLS, EAP-AKA

Intel® Centrino® Wireless-N 1030 and Intel® Centrino® Advanced-N 6230

Form Factor PCI Express* Half-Mini Card Dimensions Half-Mini Card: Width 1.049 in x Length 1.18 in x Height 0.18 in (26.64 mm x 30 mm x 4.5

mm)

Antenna Interface Connector

Antenna Diversity

Network Standards

Connector Interface

Voltage 3.3 V Operating

Temperature Humidity 50% to 95% non - condensing (at temperatures of 25 ºC to 35 ºC) WiFi Network

Standards

Frequency Modulation

Frequency band 5.15 GHz - 5.85 GHz (dependent on country) 2.400 - 2.4835 GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM CCK, DQPSK, DBPSK Wireless

Medium Channels All channels as defined by the relevant specification and country rules. IEEE 802.11n

Data Rates

Hirose U.FL-R-SMT mates with cable connector U.FL-LP - 066

On-board diversity

802.11a/b/g/n (varies by adapter) and Bluetooth 3.0 + HS

52-pin Mini Card edge connector

0 to +80 degrees Celsius

Intel® Centrino® Wireless-N 1030: 802.11b/g/n Intel® Centrino® Advanced- N 6230: 802.11a/g/n

5 GHz (802.11a/n) 2.4 GHz (802.11b/g/n)

5 GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM)

Intel® Centrino® Advanced- N 6230: Tx/Rx (Mbps): 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117,

115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 Intel® Centrino® Wireless-N 1030:

2.4 GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM)

Rx (Mbps): 300, 270, 243, 240, 180

Rx/Tx (Mbps): 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2

IEEE 802.11a Data Rates

IEEE 802.11g Data Rates

IEEE 802.11b Data Rates

Bluetooth Bluetooth Version 3.0 + HS

General

Operating Systems

54, 48, 36, 24, 18, 12, 9, 6 Mbps

11, 5.5, 2, 1 Mbps

Microsoft Windows* XP (32 -bit and 64-bit) Windows Vista* (32 -bit and 64-bit) Windows* 7 (32-bit and 64-bit)

Wi-Fi Alliance* certification

Cisco Compatible Extensions certification

WLAN Standard IEEE 802.11g, 802.11b, 802.11a, 802.11n Architecture Infrastructure or ad hoc (peer-to-peer) operating modes Security WPA -Personal, WPA2-Personal, WPA-Enterprise, WPA2 -Enterprise, AES- CCMP 128-bit, WEP 128-

Product Safety UL, C-UL, CB (IEC 60590)

Wi-Fi* certification for 802.11b, 802.11g, 802.11a, 802.11h, 802.11d, WPA-Personal, WPAEnterprise, WPA2- Personal, WPA2-Enterprise, WPS, WMM, WMM Power Save, EAP-SIM, LEAP, PEAP, TKIP, EAP-FAST, EAP-TLS, EAP-TTLS, EAP- AKA, P2P

Cisco Compatible Extensions, v4.0

bit and 64 -bit; 802.1X: EAP-SIM, LEAP, PEAP, TKIP, EAP-FAST, EAP-TLS, EAP-TTLS, EAP- AKA

Intel® Centrino® Advanced-N 6235

Form Factor PCI Express* Half-Mini Card Dimensions Half-Mini Card: Width 1.049 in x Length 1.18 in x Height 0.18 in (26.64 mm x 30 mm x 4.5

mm)

Antenna Interface Connector

Antenna Diversity

Network Standards

Connector Interface

Voltage 3.3 V Operating

Temperature Humidity 50% to 95% non - condensing (at temperatures of 25 ºC to 35 ºC)

Frequency Modulation

Frequency band 5.15 GHz - 5.85 GHz (dependent on country) 2.400 - 2.4835 GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM CCK, DQPSK, DBPSK Wireless 5 GHz UNII: Orthogonal Frequency Division 2.4 GHz ISM: Orthogonal Frequency Division

Hirose U.FL-R-SMT mates with cable connector U.FL-LP - 066

On-board diversity

802.11a/b/g/n and Bluetooth 4.0

52-pin Mini Card edge connector

0 to +80 degrees Celsius

5 GHz (802.11a/n) 2.4 GHz (802.11b/g/n)

Medium Multiplexing (OFDM) Multiplexing (OFDM) Channels All channels as defined by the relevant specification and country rules. IEEE 802.11n

Data Rates IEEE 802.11a

Data Rates IEEE 802.11g

Data Rates IEEE 802.11b

Data Rates Bluetooth Bluetooth Version 4.0 (3.0 +HS )

General

Operating Systems

Wi-Fi Alliance* certification

Cisco Compatible Extensions certification

WLAN Standard IEEE 802.11g, 802.11b, 802.11a, 802.11n Architecture Infrastructure or ad hoc (peer-to-peer) operating modes Security WPA -Personal, WPA2-Personal, WPA-Enterprise, WPA2 -Enterprise, AES- CCMP 128-bit, WEP 128-

Product Safety UL, C-UL, CB (IEC 60590)

Tx/Rx (Mbps): 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117,

115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 54, 48, 36, 24, 18, 12, 9, 6 Mbps

54, 48, 36, 24, 18, 12, 9, 6 Mbps

11, 5.5, 2, 1 Mbps

Windows* 7 (32-bit and 64-bit)

Wi-Fi* certification for 802.11b, 802.11g, 802.11a, 802.11h, 802.11d, WPA-Personal, WPAEnterprise, WPA2- Personal, WPA2-Enterprise, WPS, WMM, WMM Power Save, EAP-SIM, LEAP, PEAP, TKIP, EAP-FAST, EAP-TLS, EAP-TTLS, EAP- AKA, P2P

Cisco Compatible Extensions, v4.0

bit and 64 -bit; 802.1X: EAP-SIM, LEAP, PEAP, TKIP, EAP-FAST, EAP-TLS, EAP-TTLS, EAP -AKA

Intel® Centrino® Advanced-N + WiMAX 6250 and Intel® Centrino® Wireless-N + WiMAX 6150

Form Factor PCI Express* Half-Mini Card Dimensions Half-Mini Card: Width 1.049 in x Length 1.18 in x Height 0.18 in (26.64 mm x 30 mm x 4.5

mm)

Antenna Interface Connector

Antenna Diversity

Connector Interface

Voltage 3.3 V Operating

Temperature Humidity 50% to 95% non - condensing (at temperatures of 25 ºC to 35 ºC) WiFi Frequency

Modulation

Frequency band 5.15 GHz - 5.85 GHz (dependent on country) 2.400 - 2.4835 GHz (dependent on country)

Hirose U.FL-R-SMT mates with cable connector U.FL-LP - 066

On-board diversity

52-pin Mini Card edge connector

0 to +80 degrees Celsius

Intel® Centrino® Advanced-N + WiMAX 6250

2.4 GHz (802.11b/g/n), 5 GHz (802.11a/n)

Intel® Centrino® Wireless-N + WiMAX 6150

2.4 GHz (802.11b/g/n)

Modulation BPSK, QPSK, 16 QAM, 64 QAM CCK, DQPSK, DBPSK Wireless

Medium Channels All channels as defined by the relevant specification and country rules. IEEE 802.11n

Data Rates

IEEE 802.11a Data Rates

IEEE 802.11g Data Rates

IEEE 802.11b Data Rates

General

Operating Systems

5 GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM)

Intel® Centrino® Wireless-N + WiMAX 6150

MIMO Configuration: 1X2

Rx: 300, 270, 243, 240, 180 Mbps Rx/Tx: 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30,

28.9, 21.7, 15, 14.4, 7.2 Mbps

Intel® Centrino® Advanced-N + WiMAX 6250

MIMO Configuration: 2X2 Tx/Rx: 300, 270, 243, 240, 180, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65,

60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps

54, 48, 36, 24, 18, 12, 9, 6 Mbps

11, 5.5, 2, 1 Mbps

Microsoft Windows* XP (32 -bit and 64-bit) Windows Vista* (32 -bit and 64-bit) Windows* 7 (32-bit and 64-bit)

2.4 GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM)

Wi-Fi Alliance* certification

Cisco Compatible Extensions certification

IEEE Feature Sets

Architecture Infrastructure or ad hoc (peer-to-peer) operating modes Security WPA - Personal, WPA2-Personal, WPA -Enterprise, WPA2-Enterprise, AES-CCMP 128 -bit, WEP 128 -

Product Safety UL, C -UL, CB (IEC 60590)

WiMAX General

Operating Systems

Wi-Fi* certification for 802.11b, 802.11g, 802.11a, 802.11h, 802.11d, WPA-Personal, WPAEnterprise, WPA2- Personal, WPA2-Enterprise, WMM, WMM Power Save, EAP- SIM, LEAP, PEAP, TKIP, EAP-FAST, EAP-TLS, EAP-TTLS, EAP- AKA

Cisco Compatible Extensions, v4.0

Intel® Centrino® Wireless-N + WiMAX 6150: IEEE 802.11b, 802.11g, 802.11n, 802.11e, 802.11i, 802.11h, 802.11d

Intel® Centrino® Advanced-N + WiMAX 6250:

802.11a, IEEE 802.11b, 802.11g, 802.11n, 802.11e, 802.11i, 802.11h, 802.11d

bit and 64 -bit; 802.1X: EAP-SIM, LEAP, PEAP, TKIP, EAP-FAST, EAP-TLS, EAP-TTLS, EAP- AKA

Microsoft Windows* XP (32 -bit and 64-bit) Windows Vista* (32 -bit and 64-bit) Windows* 7 (32-bit and 64-bit)

Standard Compliance

WiMAX System Profile Feature set

802.16e-2005 Corrigenda 2 (D4)

Intel® Centrino® Wireless-N + WiMAX 6150: Mobile WiMAX release 1, Wave II. Supports 3A and 1A/B profiles

Intel® Centrino® Advanced-N + WiMAX 6250:

Mobile WiMAX release 1, Wave II. Supports 3A, 5A/C, 1A/B, and 5BL profiles Security Key Management Protocol (PKMv2) Encryption 128-bit CCMP (Counter-Mode/CBC -MAC) based on AES encryption

WiMAX

Frequency band Intel® Centrino® Wireless -N + WiMAX 6150: 2.3- 2.4 GHz / 2.496 -2.690 GHz

Intel® Centrino® Advanced-N + WiMAX 6250: 2.3 -2.4 GHz / 2.496-2.690 GHz / 3.4 - 3.8 GHz Modulation UL - QPSK, 16 QAM

DL - QPSK, 16 QAM, 64 QAM Wireless

Medium

WiMAX Network Release Feature set

Rate Performance

Duplex mode: TDD operations Scalable OFDMA (SOFDMA): 512 and 1024 FFT

sub -carrier permutation: PUSC Intel® Centrino® Wireless-N + WiMAX 6150:

Channel bandwidths: 5 and 10 MHz Intel® Centrino® Advanced-N + WiMAX 6250:

Channel bandwidths: 5, 7, 8.75 and 10 MHz

SPWG/NWG Release 1.5

Intel® Centrino® Wireless-N + WiMAX 6150:

Up to 10 Mbps DL and 4 Mbps UL @ peak rate

(OTA performance, 10MHz channel)

Intel® Centrino® Advanced-N + WiMAX 6250:

Up to 20 Mbps DL and 6 Mbps UL @ peak rate

(OTA performance, 10MHz channel) RF Transmitter

Output Power

Compliance with Power class 2

Intel® Centrino® Advanced-N 6200, Intel® Centrino® Advanced-N 6205 and Intel® Centrino® Ultimate-N 6300

Form Factor Intel® Centrino® Advanced-N 6200, Intel® Centrino® Ultimate-N 6300:

PCI Express* Full-Mini Card and Half-Mini Card.

Intel® Centrino® Advanced-N 6205: PCI Express* Half-Mini Card. Dimensions Full-Mini Card: Width 2.00 in x Length 1.18 in x Height 0.18 in (50.95 mm x 30 mm x 4.5 mm)

Half-Mini Card: Width 1.049 in x Length 1.18 in x Height 0.18 in (26.64 mm x 30 mm x 4.5

mm) Antenna

Interface Connector

Antenna Diversity

Connector Interface

Voltage 3.3 V Operating

Temperature Humidity 50% to 95% non - condensing (at temperatures of 25 ºC to 35 ºC)

Frequency 5 GHz (802.11a/n) 2.4 GHz (802.11b/g/n)

Hirose U.FL-R-SMT mates with cable connector U.FL-LP - 066

On-board diversity

52-pin Mini Card edge connector

0 to +80 degrees Celsius

Modulation

Frequency band 5.15 GHz - 5.85 GHz (dependent on country) 2.400 - 2.4835 GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM CCK, DQPSK, DBPSK Wireless

Medium

5 GHz UNII: Orthogonal Frequency Division

Multiplexing (OFDM)

2.4 GHz ISM: Orthogonal Frequency Division

Multiplexing (OFDM) Channels All channels as defined by the relevant specification and country rules. IEEE 802.11n

Intel® Centrino® Ultimate -N 6300:

Data Rates

Tx/Rx: 450, 405, 360, 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 Mbps

Intel® Centrino® Advanced-N 6200, Intel® Centrino® Advanced - N 6205: Tx/Rx: 300, 270, 243, 240, 180, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65,

60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 Mbps

IEEE 802.11a

54, 48, 36, 24, 18, 12, 9, 6 Mbps

Data Rates IEEE 802.11g

54, 48, 36, 24, 18, 12, 9, 6 Mbps

Data Rates IEEE 802.11b

11, 5.5, 2, 1 Mbps

Data Rates

General

Operating Systems

Microsoft Windows* XP (32 -bit and 64-bit) Windows Vista* (32 -bit and 64-bit) Windows* 7 (32-bit and 64-bit)

Wi-Fi Alliance* certification

Wi-Fi* certification for 802.11b, 802.11g, 802.11a, 802.11h, 802.11d, WPA-Personal, WPAEnterprise, WPA2- Personal, WPA2-Enterprise, WMM, WMM Power Save, EAP- SIM, LEAP, PEAP, TKIP, EAP-FAST, EAP-TLS, EAP-TTLS, EAP- AKA

Cisco

Cisco Compatible Extensions, v4.0 Compatible Extensions certification

WLAN Standard IEEE 802.11g, 802.11b, 802.11a, 802.11n Architecture Infrastructure or ad hoc (peer-to-peer) operating modes Security WPA - Personal, WPA2-Personal, WPA -Enterprise, WPA2-Enterprise, AES-CCMP 128 -bit, WEP 128 -

bit and 64 -bit; 802.1X: EAP-SIM, LEAP, PEAP, TKIP, EAP-FAST, EAP-TLS, EAP-TTLS, EAP- AKA Product Safety UL, C -UL, CB (IEC 60590)

Back to Top Back to Contents

Trademarks and Disclaimers

Back to Contents

Important Information

Safety Information Third Party Software Notices

Safety Information

It is important that you read the safety information regarding your WiFi adapter. Please see the User's Guide for safety and regulatory notices.

Third Party Software Notices

Portions of Intel® PROSet/Wireless WiFi Connection Utility include software under the following terms:

OpenSSL License

following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgment: "This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)"

4. The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact opensslcore@openssl.org.

5. Products derived from this software may not be called "OpenSSL" nor may "OpenSSL" appear in their names without prior written permission of the OpenSSL Project.

6. Redistributions of any form whatsoever must retain the following acknowledgment: "This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)"

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT "AS IS" AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

This product includes cryptographic software written by Eric Young (eay@cryptsoft.com). This product includes software written by Tim Hudson (tjh@cryptsoft.com).

Original SSLeay License

This package is an SSL implementation written by Eric Young (eay@cryptsoft.com). The implementation was written so as to conform with Netscape's SSL.

This library is free for commercial and non-commercial use as long as the following conditions are adhered to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson (tjh@cryptsoft.com).

Copyright remains Eric Young's, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgement: "This product includes cryptographic software written by Eric Young (eay@cryptsoft.com)" The word 'cryptographic' can be left out if the routines from the library being used are not cryptographic related.

4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement: "This product includes software written by Tim Hudson (tjh@cryptsoft.com)"

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG "AS IS:' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

The license and distribution terms for any publicly available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution license [including the GNU Public License.]

zlib.h -- interface of the 'zlib' general purpose compression library, version 1.2.3, July 18th, 2005

liable for any damages arising from the use of this software. Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions:

1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required.

2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.

3. This notice may not be removed or altered from any source distribution.

Jean-loup Gailly jloup@gzip.org Mark Adler madler@alumni.caltech.edu

Adapter Driver

Portions of the driver include software under the following terms:

WPA Supplicant

Copyright (c) 2003-2007, Jouni Malinen <jkmaline@cc.hut.fi> and contributors. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. Neither the name of Jouni Malinen nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

__________

LICENSE TERMS The free distribution and use of this software in both source and binary form is allowed (with or without changes)

provided that:

1. Distributions of this source code include the above copyright notice, this list of conditions and the following disclaimer;

2. distributions in binary form include the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other associated materials;

3. the copyright holder's name is not used to endorse products built using this software without specific written permission.

DISCLAIMER This software is provided 'as is' with no explicit or implied warranties in respect of its properties, including, but not

limited to, correctness and fitness for purpose. Issue Date: 29/07/2002 This file contains the definitions required to use AES (Rijndael) in C.

Portions Licensed from Devicescape Software, Inc.

"Odd Button" Artistic License

Portions of this software contain the standard version of "Odd Button" licensed under the Artistic License. The source code for "Odd Button" may be found online at http://sourceforge.net/projects/oddbutton.

September 15, 2011

Back to Top Back to Contents

Trademarks and Disclaimers

Back to Contents

Customer Support

Intel support is available online or by telephone. Available services include the most up-to - date product information, installation instructions about specific products, and troubleshooting tips.

Online Support

Technical Support: http://www.intel.com/support Network Product Support: http://www.intel.com/network Corporate Web Site: http://www.intel.com

Back to Top Back to Contents

Trademarks and Disclaimers

Back to Contents

Glossary of Terms

Term Definition

802.11 The 802.11 standard refers to a family of specifications developed by the IEEE for wireless LAN technology. The 802.11 specifies an over-the - air interface between a wireless client and a base station or between two wireless clients and provides 1 or 2 Mbps transmission in the 2.4 GHz band using either frequency hopping spread spectrum (FHSS) or direct sequence spread spectrum (DSSS).

802.11a The 802.11a standard specifies a maximum data transfer rate of 54 Mbps and an operating frequency of 5 GHz. The 802.11a standard uses the Orthogonal Frequency Division Multiplexing (OFDM) transmission method. Additionally, the 802.11a standard supports 802.11 features such as WEP encryption for security.

802.11b 802.11b is an extension to 802.11 that applies to wireless networks and provides 11 Mbps transmission (with a fallback to 5.5, 2 and 1 Mbps) in the 2.4 GHz band. 802.11b uses only DSSS. Throughput data rate 5+ Mbps in the 2.4 GHz band.

802.11g The 802.11g standard specifies a maximum data transfer rate of 54 Mbps, an operating frequency of 2.4GHz, and WEP encryption for security. 802.11g networks are also referred to as Wi-Fi* networks.

802.11n A task group of the IEEE 802.11 committee has defined a new draft specification that provides for increased throughput speeds of up to 540 Mbps. The specification provides for MultipleInput- Multiple-Output (MIMO) technology, or using multiple receivers and multiple transmitters in both the client and access point, to achieve improved performance.

802.1X 802.1X is the IEEE Standard for Port- Based Network Access Control. This is used in conjunction with EAP methods to provide access control to wired and wireless networks.

AAA Server Authentication, Authorization and Accounting Server. A system to control access to computer

resources and track user activity.

Access Point (AP)

Ad Hoc Network

AES-CCMP Advanced Encryption Standard - Counter CBC-MAC Protocol is the new method for privacy

Authentication Verifies the identity of a user logging onto a network. Passwords, digital certificates, smart cards

Available network

BER Bit Error Rate. The ratio of errors to the total number of bits being sent in a data transmission

Bit Rate The total number of bits (ones and zeros) per second that a network connection can support.

Broadcast SSID Used to allow an access point to respond to clients on a wireless network by sending probes. BSSID A unique identifier for each wireless client on a wireless network. The Basic Service Set

A device that connects wireless devices to another network. For example, a wireless LAN, Internet modem or others.

A communication configuration in which every computer has the same capabilities, and any computer can initiate a communication session. Also known as a peer-to -peer network, a device to device network or a computer-to -computer network.

protection of wireless transmissions specified in the IEEE 802.11i standard. AES-CCMP provides a stronger encryption method than TKIP. The AES algorithm is capable of using cryptographic keys of 128, 192, and 256 bits to encrypt and decrypt data in 128 -bit blocks. AES-CCMP uses the AES block cipher, but restricts the key length to 128 bits. AES-CCMP incorporates two sophisticated cryptographic techniques (counter mode and CBC -MAC) to provide improved security between the mobile client and the access point.

and biometrics are used to prove the identity of the client to the network. Passwords and digital certificates are also used to identify the network to the client.

One of the networks listed under Available networks on the Wireless Networks tab of the Wireless Network Connection Properties (Windows* XP environment). Any wireless network that is broadcasting and is within receiving range of the WiFi adapter appears on the list.

from one location to another.

Note that this bit rate will vary, under software control, with different signal path conditions.

Identifier (BSSID) is the Ethernet MAC address of each adapter on the network.

CA (Certificate Authority)

CCX (Cisco Compatible eXtension)

Certificate Used for client authentication. A certificate is registered on the authentication server (for

CKIP Cisco Key Integrity Protocol (CKIP) is a Cisco proprietary security protocol for encryption in

Client computer The computer that gets its Internet connection by sharing either the host computer's connection

DSSS Direct Sequence Spread Spectrum. Technology used in radio transmission. Incompatible with

EAP Short for Extensible Authentication Protocol, EAP sits inside of Point -to-Point Protocol's (PPP)

EAP-AKA EAP-AKA (Extensible Authentication Protocol Method for UMTS Authentication and Key

EAP-FAST EAP-FAST, like EAP-TTLS and PEAP, uses tunneling to protect traffic. The main difference is that

A corporate certification authority implemented on a server. In addition, Internet Explorer's certificate can import a certificate from a file. A trusted CA certificate is stored in the root store.

Cisco Compatible Extensions Program ensures that devices used on Cisco wireless LAN infrastructure meet the security, management and roaming requirements.

example, RADIUS server) and used by the authenticator.

802.11 media. CKIP uses a key message integrity check and message sequence number to improve 802.11 security in infrastructure mode. CKIP is Cisco's version of TKIP.

or the access point's connection.

FHSS.

authentication protocol and provides a generalized framework for several different authentication methods. EAP is supposed to head off proprietary authentication systems and let everything from passwords to challenge-response tokens and public -key infrastructure certificates all work smoothly.

Agreement) is an EAP mechanism for authentication and session key distribution, using the Universal Mobile Telecommunications System (UMTS) Subscriber Identity Module (USIM). The USIM card is a special smart card used with cellular networks to validate a given user with the network.

EAP-FAST does not use certificates to authenticate. Provisioning in EAP-FAST is negotiated solely by the client as the first communication exchange

when EAP-FAST is requested from the server. If the client does not have a pre-shared secret Protected Access Credential (PAC), it can request to initiate a provisioning EAP-FAST exchange to dynamically obtain one from the server.

EAP-FAST documents two methods to deliver the PAC: manual delivery through an out - of -band secure mechanism, and automatic provisioning.

Manual delivery mechanisms can be any delivery mechanism that the administrator of the network feels is sufficiently secure for their network.

Automatic provisioning establishes an encrypted tunnel to protect the authentication of the client and the delivery of the PAC to the client. This mechanism, while not as secure as a manual method may be, is more secure than the authentication method used in LEAP.

The EAP-FAST method can be divided into two parts: provisioning, and authentication. The provisioning phase involves the initial delivery of the PAC to the client. This phase only needs to be performed once per client and user.

EAP-GTC The EAP-GTC (Generic Token Card) is similar to the EAP-OTP except with hardware token cards.

The request contains a displayable message, and the response contains the string read from the hardware token card.

EAP-OTP EAP-OTP (One-Time Password) is similar to MD5, except it uses the OTP as the response. The

request contains a displayable message. The OTP method is defined in RFC 2289.

EAP-SIM Extensible Authentication Protocol -Subscriber Identity Module (EAP -SIM) authentication can be

used with:

Network Authentication types: Open, Shared, and WPA*-Enterprise, WPA2* -Enterprise. Data Encryption types: None, WEP and CKIP.

A SIM card is a special smart card that is used by Global System for Mobile Communications (GSM) based digital cellular networks. The SIM card is used to validate your credentials with the network

EAP-TLS A type of authentication method that uses EAP and a security protocol called the Transport

Layer Security (TLS). EAP -TLS uses certificates that use passwords. EAP-TLS authentication supports dynamic WEP key management.

EAP-TTLS A type of authentication method that uses EAP and Tunneled Transport Layer Security (TTLS).

EAP-TTLS uses a combination of certificates and another security method such as passwords.

Encryption Scrambling data so that only the authorized recipient can read it. Usually a key is needed to

interpret the data.

FHSS Frequency-Hop Spread Spectrum. Technology used in radio transmission. Incompatible with

DSSS.

File and printer sharing

Fragmentation threshold

GHz (Gigahertz)

Host computer The computer that is directly connected to the Internet via a modem or network adapter. Infrastructure

network

IEEE Institute of Electrical and Electronics Engineers (IEEE) is an organization involved in defining

Internet Protocol (IP) address

LAN (Local Area Network)

LEAP (Light Extensible Authentication Protocol)

MAC (Media Access Control) Address

Mbps (Megabits-persecond)

MHz (Megahertz)

MIC (Michael) Message Integrity Check (commonly called Michael). MS-CHAP An EAP mechanism used by the client. Microsoft Challenge Authentication Protocol (MS- CHAP)

ns(Nanosecond) 1 billionth (1/1,000,000,000) of a second. OFDM Orthogonal Frequency Division Multiplexing. Open

authentication PEAP Protected Extensible Authentication Protocol (PEAP) is an Internet Engineering Task Force (IETF)

A capability that allows a number of people to view, modify, and print the same file(s) from different computers.

The threshold at which the wireless adapter breaks the packet into multiple frames. This determines the packet size and affects the throughput of the transmission.

A unit of frequency equal to 1,000,000,000 cycles per second.

A wireless network centered around an access point. In this environment, the access point not only provides communication with the wired network, but also mediates wireless network traffic in the immediate neighborhood.

computing and communications standards. The address of a computer that is attached to a network. Part of the address designates which

network the computer is on, and the other part represents the host identification.

A high -speed, low -error data network covering a relatively small geographic area.

A version of Extensible Authentication Protocol (EAP). LEAP is a proprietary extensible authentication protocol developed by Cisco that provides a challenge-response authentication mechanism and dynamic key assignment.

A hardwired address applied at the factory. It uniquely identifies network hardware, such as a wireless adapter, on a LAN or WAN.

Transmission speed of 1,000,000 bits per second.

A unit of frequency equal to 1,000,000 cycles per second.

Version 2, is used over an encrypted channel to enable server validation. The challenge and response packets are sent over a non-exposed TLS encrypted channel.

Allows any device network access. If encryption is not enabled on the network, any device that knows the Service Set Identifier (SSID) of the access point can gain access to the network.

draft protocol sponsored by Microsoft, Cisco, and RSA Security. PEAP creates an encrypted tunnel similar to the tunnel used in secure web pages (SSL). Inside the encrypted tunnel, a

number of other EAP authentication methods can be used to perform client authentication. PEAP requires a TLS certificate on the RADIUS server, but unlike EAP-TLS there is no requirement to have a certificate on the client. PEAP has not been ratified by the IETF. The IETF is currently comparing PEAP and TTLS (Tunneled TLS) to determine an authentication standard for 802.1X authentication in 802.11 wireless systems. PEAP is an authentication type designed to take advantage of server-side EAP- Transport Layer Security (EAP- TLS) and to support various authentication methods, including user passwords and one-time passwords, and Generic Token Cards.

Peer-to-Peer mode

Power save mode

Preferred network

RADIUS (Remote Authentication Dial-In User Service)

RF (Radio Frequency)

Roaming Movement of a wireless node between two micro cells. Roaming usually occurs in infrastructure

RTS threshold The number of frames in the data packet at or above which an RTS/CTS (request to send/clear

Shared key An encryption key known only to the receiver and sender of data. This is also referred to as a

SIM (Subscriber Identity Module)

Silent mode Silent Mode Access Points or Wireless Routers have been configured to not broadcast the SSID

Single Sign On Single Sign On feature set allows the 802.1X credentials to match your Windows log on user

SSID (Service Set Identifier)

stealth A stealth access point is one that has the capability and is configured to not broadcast its SSID.

TKIP (Temporal Key Integrity

A wireless network structure that allows wireless clients to communicate directly with each other without using an access point.

The state in which the radio is periodically powered down to conserve power. When the portable computer is in Power Save mode, received packets are stored in the access point until the wireless adapter wakes up.

One of the networks that has been configured. Such networks are listed under Preferred networks on the Wireless Networks tab of the Wireless Network Connection Properties (Windows* XP environment).

RADIUS is an authentication and accounting system that verifies user's credentials and grants access to requested resources.

The international unit for measuring frequency is Hertz (Hz), which is equivalent to the older unit of cycles per second. One MegaHertz (MHz) is one million Hertz. One GigaHertz (GHz) is one billion Hertz. For reference: the standard US electrical power frequency is 60 Hz, the AM broadcast radio frequency band is 0.55 -1.6 MHz, the FM broadcast radio frequency band is 88 108 MHz, and microwave ovens typically operate at 2.45 GHz.

networks built around multiple access points. Current wireless network roaming is only supported in the same subnet of a network.

to send) handshake is turned on before the packet is sent. The default value is 2347.

pre-shared key. A SIM card is used to validate credentials with the network. A SIM card is a special smart card

used by GSM-based digital cellular networks.

for the wireless network. This makes it necessary to know the SSID in order to configure the wireless profile to connect to the access point or wireless router.

name and password credentials for wireless network connections. SSID or network name is a value that controls access to a wireless network. The SSID for your

wireless network card must match the SSID for any access point that you want to connect with. If the value does not match, you are not granted access to the network. Each SSID may be up to 32 alphanumeric characters long and is case-sensitive.

This is the WiFi network name that appears when a DMU (Device Management Utility, such as Intel® PROSet/Wireless WiFi Connection Utility) scans for available wireless networks. Although this can enhance wireless network security, it is commonly considered a weak security feature. To connect to a stealth access point, a user must specifically know the SSID and configure their DMU accordingly. The feature is not a part of the 802.11 specification, and is known by differing names by various vendors: closed mode, private network, SSID broadcasting.

Temporal Key Integrity protocol improves data encryption. Wi - Fi Protected Access* uses its TKIP. TKIP provides important data encryption enhancements including a re - keying method.

Protocol) TKIP is part of the IEEE 802.11i encryption standard for wireless networks. TKIP is the next

generation of WEP, the Wired Equivalency Protocol, which is used to secure 802.11 wireless networks. TKIP provides per packet key mixing, a message integrity check and a re-keying mechanism, thus fixing the flaws of WEP.

TLS (Transport Layer Security)

TTLS (Tunneled Transport Layer Security)

WEP (Wired Equivalent Privacy)

WEP Key Either a pass phrase or hexadecimal key.

Wi-Fi* (Wireless Fidelity)

WiMAX WiMAX, the Worldwide Interoperability for Microwave Access, is a telecommunications

Wireless router A stand-alone wireless hub that allows any computer that has a wireless network adapter to

WLAN (Wireless Local-Area Network)

WPA* (Wi- Fi Protected Access)

WPA2* (Wi-Fi Protected Access 2)

WPA-Enterprise Wi-Fi Protected Access -Enterprise applies to corporate users. A new standards - based,

A type of authentication method using the Extensible Authentication Protocol (EAP) and a security protocol called the Transport Layer Security (TLS). EAP- TLS uses certificates which use passwords. EAP -TLS authentication supports dynamic WEP key management. The TLS protocol is intended to secure and authenticate communications across a public network through data encryption. The TLS Handshake Protocol allows the server and client to provide mutual authentication and to negotiate an encryption algorithm and cryptographic keys before data is transmitted.

These settings define the protocol and the credentials used to authenticate a user. In TTLS, the client uses EAP-TLS to validate the server and create a TLS-encrypted channel between the client and server. The client can use another authentication protocol. Typically password -based protocols challenge over this encrypted channel to enable server validation. The challenge and response packets are sent over a non-exposed TLS encrypted channel. TTLS implementations today support all methods defined by EAP, as well as several older methods (CHAP, PAP, MSCHAP and MS -CHAP -V2). TTLS can easily be extended to work with new protocols by defining new attributes to support new protocols.

Wired Equivalent Privacy, 64 - and 128-bit (64 -bit is sometimes referred to as 40 -bit). This is a low -level encryption technique designed to give the user about the same amount of privacy that he would expect from a LAN. WEP is a security protocol for wireless local area networks (WLANs) defined in the 802.11b standard. WEP is designed to provide the same level of security as that of a wired LAN. WEP aims to provide security by data over radio waves so that it is protected as it is transmitted from one end point to another.

The pass phrase must be 5 ASCII characters for 64-bit WEP or 13 ASCII characters for 128-bit WEP. For pass phrases, 0-9, a-z, A-Z, and ~!@#$%^&*()_+|`-={}|[]\:";'<> ?,./ are all valid characters. The hex key must be 10 hexadecimal characters (0 -9, A-F) for 64 -bit WEP or 26 hexadecimal characters (0-9, A-F) for 128-bit WEP.

Is meant to be used generically when referring of any type to 802.11 network, whether

802.11b, 802.11a, or dual -band.

technology aimed at providing wireless data over long distances in a variety of ways, from pointto -point links to full mobile cellular type access. It is based on the IEEE 802.16 standard. The name WiMAX was created by the WiMAX Forum, which was formed in June 2001 to promote conformance and interoperability of the standard. The forum describes WiMAX as "a standardsbased technology enabling the delivery of last mile wireless broadband access as an alternative to cable and DSL."

communicate with another computer within the same network and to connect to the Internet. A type of local -area network that uses high-frequency radio waves rather than wires to

communicate between nodes.

This is a security enhancement that strongly increases the level of data protection and access control to a wireless network. WPA is an interim standard that will be replaced with the IEEE's

802.11i standard upon its completion. WPA consists of RC4 and TKIP and provides support for BSS (Infrastructure) mode only. WPA and WPA2 are compatible.

This is the second generation of WPA that complies with the IEEE TGi specification. WPA2 consists of AES encryption, pre -authentication and PMKID caching. It provides support for BSS (Infrastructure) mode and IBSS (ad hoc) mode. WPA and WPA2 are compatible.

interoperable security technology for wireless LAN (subset of IEEE 802.11i draft standard) that encrypts data sent over radio waves. WPA is a Wi - Fi standard that was designed to improve

upon the security features of WEP as follows:

Improved data encryption through the temporal key integrity protocol (TKIP). TKIP uses a hashing algorithm to scramble the encryption keys and adds an integrity -checking feature to ensure that the keys have not been tampered with.

User authentication, which is generally missing in WEP, through the extensible authentication protocol (EAP). WEP regulates access to a wireless network based on a computer's hardware - specific MAC address, which is relatively simple to be sniffed out and stolen. EAP is built on a more secure public-key encryption system to ensure that only authorized network users can access the network.

WPA is an interim standard that will be replaced with the IEEE's 802.11i standard upon its completion.

WPA-Personal Wi-Fi Protected Access-Personal provides a level of security in the small network or home

environment.

WPA-PSK (WiFi ProtectedAccess Pre Shared Key)

WPA-PSK mode does not use an authentication server. It can be used with the data encryption types WEP or TKIP. WPA- PSK requires configuration of a pre -shared key (PSK). You must enter a pass phrase or 64 hex characters for a pre -shared key of length 256 -bits. The data encryption key is derived from the PSK.

Back to Top Back to Contents

Trademarks and Disclaimers

Back to Contents

Warranty

Product Warranty Information

One-Year Limited Hardware Warranty

Limited Warranty

In this warranty statement, the term "Product" applies to the wireless adapters listed in Intel warrants to the purchaser of the Product that the Product, if properly used and installed, will be free from

defects in material and workmanship and will substantially conform to Intel’s publicly available specifications for the Product for a period of one (1) year beginning on the date the Product was purchased in its original sealed packaging.

SOFTWARE OF ANY KIND DELIVERED WITH OR AS PART OF THE PRODUCT IS EXPRESSLY PROVIDED "AS IS", SPECIFICALLY EXCLUDING ALL OTHER WARRANTIES, EXPRESS, IMPLIED (INCLUDING WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE), provided however, that Intel warrants that the media on which the software is furnished will be free from defects for a period of ninety (90) days from the date of delivery. If such a defect appears within the warranty period, you may return the defective media to Intel for replacement or alternative delivery of the software at Intel's discretion and without charge. Intel does not warrant or assume responsibility for the accuracy or completeness of any information, text, graphics, links or other items contained within the software.

If the Product which is the subject of this Limited Warranty fails during the warranty period for reasons covered by this Limited Warranty, Intel, at its option, will:

REPAIR the Product by means of hardware and/or software; OR REPLACE the Product with another product, OR, if Intel is unable to repair or replace the Product, REFUND the then - current Intel price for the Product at the time a claim for warranty service is made to

Intel under this Limited Warranty.

THIS LIMITED WARRANTY, AND ANY IMPLIED WARRANTIES THAT MAY EXIST UNDER APPLICABLE STATE, NATIONAL, PROVINCIAL OR LOCAL LAW, APPLY ONLY TO YOU AS THE ORIGINAL PURCHASER OF THE PRODUCT.

Specifications.

Extent of Limited Warranty

Intel does not warrant that the Product, whether purchased stand-alone or integrated with other products, including without limitation, semi -conductor components, will be free from design defects or errors known as "errata." Current characterized errata are available upon request. Further, this Limited Warranty does NOT cover: (i) any costs associated with the replacement or repair of the Product, including labor, installation or other costs incurred by you, and in particular, any costs relating to the removal or replacement of any Product soldered or otherwise permanently affixed to any printed circuit board or integrated with other products; (ii) damage to the Product due to external causes, including accident, problems with electrical power, abnormal, mechanical or environmental conditions, usage not in accordance with product instructions, misuse, neglect, accident, abuse, alteration, repair, improper or unauthorized installation or improper testing, or (iii) any Product which has been modified or operated outside of Intel’s publicly available specifications or where the original product identification markings (trademark or serial number) have been removed, altered or obliterated from the Product; or (iv) issues resulting from modification (other than by Intel) of software products provided or included in the Product, (v) incorporation of software products, other than those software products provided or included in the Product by Intel, or (vi) failure to apply Intel-supplied modifications or corrections to any software provided with or included in the Product.

How to Obtain Warranty Service

To obtain warranty service for the Product, you may contact your original place of purchase in accordance with its instructions or you may contact Intel. To request warranty service from Intel, you must contact the Intel Customer

Support ("ICS") center in your region (http://www.intel.com/support/wireless/) within the warranty period during normal business hours (local time), excluding holidays and return the Product to the designated ICS center. Please be prepared to provide: (1) your name, mailing address, email address, telephone numbers and, in the USA, valid credit card information; (2) proof of purchase; (3) model name and product identification number found on the Product; and (4) an explanation of the problem. The Customer Service Representative may need additional information from you depending on the nature of the problem. Upon ICS's verification that the Product is eligible for warranty service, you will be issued a Return Material Authorization ("RMA") number and provided with instructions for returning the Product to the designated ICS center. When you return the Product to the ICS center, you must include the RMA number on the outside of the package. Intel will not accept any returned Product without an RMA number, or that has an invalid RMA number, on the package. You must deliver the returned Product to the designated ICS center in the original or equivalent packaging, with shipping charges prepaid (within the USA), and assume the risk of damage or loss during shipment. Intel may elect to repair or replace the Product with either a new or reconditioned Product or components, as Intel deems appropriate. The repaired or replaced product will be shipped to you at the expense of Intel within a reasonable period of time after receipt of the returned Product by ICS. The returned Product shall become Intel’s property on receipt by ICS. The replacement product is warranted under this written warranty and is subject to the same limitations of liability and exclusions for ninety (90) days or the remainder of the original warranty period, whichever is longer. If Intel replaces the Product, the Limited Warranty period for the replacement Product is not extended.

WARRANTY LIMITATIONS AND EXCLUSIONS

THIS WARRANTY REPLACES ALL OTHER WARRANTIES FOR THE PRODUCT AND INTEL DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, NON -INFRINGEMENT, COURSE OF DEALING AND USAGE OF TRADE. Some states (or jurisdictions) do not allow the exclusion of implied warranties so this limitation may not apply to you. ALL EXPRESS AND IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE LIMITED WARRANTY PERIOD. NO WARRANTIES APPLY AFTER THAT PERIOD. Some states (or jurisdictions) do

not allow limitations on how long an implied warranty lasts, so this limitation may not apply to you.

LIMITATIONS OF LIABILITY

INTEL’S RESPONSIBILITY UNDER THIS OR ANY OTHER WARRANTY, IMPLIED OR EXPRESS, IS LIMITED TO REPAIR, REPLACEMENT OR REFUND, AS SET FORTH ABOVE. THESE REMEDIES ARE THE SOLE AND EXCLUSIVE REMEDIES FOR ANY BREACH OF WARRANTY. TO THE MAXIMUM EXTENT PERMITTED BY LAW, INTEL IS NOT RESPONSIBLE FOR ANY DIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR UNDER ANY OTHER LEGAL THEORY (INCLUDING WITHOUT LIMITATION, LOST PROFITS, DOWNTIME, LOSS OF GOODWILL, DAMAGE TO OR REPLACEMENT OF EQUIPMENT AND PROPERTY, AND ANY COSTS OF RECOVERING, REPROGRAMMING, OR REPRODUCING ANY PROGRAM OR DATA STORED IN OR USED WITH A SYSTEM CONTAINING THE PRODUCT), EVEN IF INTEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some states (or jurisdictions) do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY BY STATE OR JURISDICTION. ANY AND ALL DISPUTES ARISING UNDER OR RELATED TO THIS LIMITED WARRANTY SHALL BE ADJUDICATED IN THE FOLLOWING FORUMS AND GOVERNED BY THE FOLLOWING LAWS: FOR THE UNITED STATES OF AMERICA, CANADA, NORTH AMERICA AND SOUTH AMERICA, THE FORUM SHALL BE SANTA CLARA, CALIFORNIA, USA AND THE APPLICABLE LAW SHALL BE THAT OF THE STATE OF DELAWARE. FOR THE ASIA PACIFIC REGION (EXCEPT FOR MAINLAND CHINA), THE FORUM SHALL BE SINGAPORE AND THE APPLICABLE LAW SHALL BE THAT OF SINGAPORE. FOR EUROPE AND THE REST OF THE WORLD, THE FORUM SHALL BE LONDON AND THE APPLICABLE LAW SHALL BE THAT OF ENGLAND AND WALES IN THE EVENT OF ANY CONFLICT BETWEEN THE ENGLISH LANGUAGE VERSION AND ANY OTHER TRANSLATED VERSION(S)OF THIS LIMITED WARRANTY (WITH THE EXCEPTION OF THE SIMPLIFIED CHINESE VERSION), THE ENGLISH LANGUAGE VERSION SHALL CONTROL.

IMPORTANT! UNLESS OTHERWISE AGREED IN WRITING BY INTEL, THE INTEL PRODUCTS SOLD HEREUNDER ARE NOT DESIGNED, OR INTENDED FOR USE IN ANY MEDICAL, LIFE SAVING OR LIFE SUSTAINING SYSTEMS, TRANSPORTATION SYSTEMS, NUCLEAR SYSTEMS, OR FOR ANY OTHER MISSION CRITICAL APPLICATION IN WHICH THE FAILURE OF THE INTEL PRODUCT COULD CREATE A SITUATION WHERE PERSONAL INJURY OR DEATH MAY OCCUR.

WEEE

Back to Top Back to Contents

Trademarks and Disclaimers

Intel 105BNHU, 6235ANH, 135BNHU, 135BNH, 105BNH User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Adapter Settings

Regulatory Information

Specifications

Important Information

Customer Support

Warranty