INTEGRAL IN74ACT132N, IN74ACT132D Datasheet

Quad 2-Input NAND Gate

with Schmitt-Trigger Inputs

High-Performance Silicon-Gate CMOS

The IN74ACT132 is identical in pinout to the LS/ALS132,
HC/HCT132. The IN74ACT132 may be used as a level converter for
interfacing TTL or NMOS outputs to High Speed CMOS inputs.

The IN74ACT132 can be used to enhance noise immunity or to
square up slowly changing waveforms.

•

TTL/NMOS Compatible Input Levels

•

Outputs Directly Interface to CMOS, NMOS, and TTL

•

Operating Voltage Range: 4.5 to 5.5 V

•

Low Input Current: 1.0 µA; 0.1 µA @ 25°C

•

Outputs Source/Sink 24 mA

TECHNICAL DATA

IN74ACT132

ORDERING INFORMATION

IN74ACT132N Plastic

IN74ACT132D SOIC

TA = -40° to 85° C for all

packages

LOGIC DIAGRAM

PIN ASSIGNMENT

FUNCTION TABLE

Inputs Output
AB Y
LL H
LH H
HL H
HH L

PIN 14 =V

PIN 7 = GND

CC

149

IN74ACT132

MAXIMUM RATINGS

*

Symbol Parameter Value Unit

V

CC

V

V

OUT

I

IN

I

OUT

I

CC

P

DC Supply Voltage (Referenced to GND) -0.5 to +7.0 V
DC Input Voltage (Referenced to GND) -0.5 to VCC +0.5 V

IN

DC Output Voltage (Referenced to GND) -0.5 to VCC +0.5 V
DC Input Current, per Pin
DC Output Sink/Source Current, per Pin
DC Supply Current, VCC and GND Pins
Power Dissipation in Still Air, Plastic DIP+

D

SOIC Package+

±

20

±

50

±

50

750
500

Tstg Storage Temperature -65 to +150

T

Lead Temperature, 1 mm from Case for 10 Seconds

L

260

(Plastic DIP or SOIC Package)

*

Maximum Ratings are those values beyond which damage to the device may occur.
Functional operation should be restricted to the Recommended Operating Conditions.
+Derating - Plastic DIP: - 10 mW/°C from 65° to 125°C

SOIC Package: : - 7 mW/°C from 65° to 125°C

mA
mA
mA

mW

°

C

°

C

RECOMMENDED OPERATING CONDITIONS

Symbol Parameter Min Max Unit

V

CC

VIN, V

T

J

T

A

I

OH

I

OL

tr, t

f

*

VIN from 0.8 V to 2.0 V

This device c ontains p rote ction ci rcuitr y to guard a gainst damage d ue to high st atic voltages or electr ic
fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated
voltages to this high-impedance circuit. For proper operation, V
GND≤(V

Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or V
Unused outputs must be left open.

DC Supply Voltage (Referenced to GND) 4.5 5.5 V
DC Input Voltage, Output Voltage (Referenced to GND) 0 V

OUT

Junction Temperature (PDIP) 140
Operating Temperature, All Package Types -40 +85
Output Current - High -24 mA
Output Current - Low 24 mA
Input Rise and Fall Time

(except Schmitt Inputs)

IN

or V

OUT

)≤VCC.

*

V
V

=4.5 V

CC

=5.5 V

CC

and V

IN

0
0

should be constrained to the range

OUT

10

8.0

CC

V

°

C

°

C

ns/V

CC

).

150