Integra HDB-RX1 User Manual

F1711-0SN29355998

*29355998*

Instruction Manual



205















The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

HDBaseT

HDBaseT Receiver

HDB-RX1

What’s in the Box





Main unit (1)  AC adaptor (1)  Cushions (4) Screws for wall attachment (4)  Label for HDBaseTTM cable (2) Label for AC adaptor cord (2)

Instruction Manual (this document)



Part Names

 





Screw hole for wall attachment: Fix with the supplied screw for wall

attachment when installing on a wall.

12V 1A INPUT jack:

support Power over Cable supplied AC adapter.

Power indicator: Lights when the power of this unit is on.

HDBaseT jack: Use an Ethernet cable to connect to the HDBaseT

OUT jack on one of our AV receivers to receive video signals, audio signals, control signals, etc.

• As they are covered with a seal when shipped, remove it when you use the jack.

• Use one of the following Ethernet cables to connect.

ｰ When using Power over Cable (PoC, refer to the back cover)

Cat6 (Category 6) cable: AWG23 cable or better, 50 m or less in length Cat5e (Category 5e) cable: AWG24 cable or better, 45 m or less in length

ｰ When not using Power over Cable (PoC, refer to the back cover

Cat6 (Category 6) cable: AWG23 cable or better, 100 m or less in length Cat5e (Category 5e) cable: AWG24 cable or better, 90 m or less in length

• It is recommended to use shielded single Ethernet cable.

• Do not connect this port to the Ethernet ports of network devices.

HDMI OUT jack: Transmit video signals and audio signals with a HDMI

cable connected to a monitor such as a TV or projector.

ACTIVE/SERVICE switch: Use in the "ACTIVE" position. ("SERVICE"

is for servicing)

RS232 port: Used when connecting to a home control system.

• Use a straight cable.

IR IN/OUT jacks: Used when connecting to a multiroom remote control

kit.

• Refer to the instruction manual of the IR receiver for the types of cables required for connection.

When connecting to a device that does not

(PoC, refer to the back cover)

, connect the

ll other trademarks are the property of their respective owners.

and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.

HDMI



Supported

Deep Color, x.v.Color™, LipSync, 3D, 4K 60 Hz, Extended Colorimetry (sYCC601, Adobe RGB, Adobe YCC601), Content Type, HDR

HDCP

Revision 1.4, 2.2

Maximum Video Resolution

4k 60 Hz (YCbCr 4:4:4)

Output jacks



HDMI OUT : 1

Other jacks



HDBaseT IN : 1 RS232 : 1 (Path through) IR IN : 1 (Path through) IR OUT : 1 (Path through)

General



Power Supply

AC 100 - 240 V, 50/60 Hz

Power Consumption

11.2 W (AC adaptor)

Dimensions (W × H × D)

205 mm × 35 mm × 89 mm 8-1/16" × 1-3/8" × 3-1/2"

Weight

0.45 kg (1 lb)

• Specifications and features are subject to change without notice.

• We will not accept responsibility for damage arising from the connection of equipment manufactured by other companies.

189

Unit : mm

Installation & Basic Connections

Other Connections

• Use an Ethernet cable to connect the HDBaseTTM OUT jack on one of the following of our AV receivers to the HDBaseT jack on this unit to transfer video, audio, and control signals. (DRX-4/DRX-5/DRX-7/DRX-R1/DRC-R1/DRX-7.1/DRX-R1.1/DRC-R1.1, and models supporting HDBaseTTM OUT sold in 2018 and thereafter)

• When using one of our AV receivers that supports Power over Cable (PoC), it is also possible to supply this unit with power over the Ethernet cable.

Wheninstallingontheoor



When installing on the floor, use the supplied cushions to help prevent damage to the floor.

ᴧ

Cushions

When installing on a wall



Fix this unit with the supplied screws for wall attachment when installing on a wall.



TV, Projector

HDMI cable

RS232 Connections



This is an example of connecting to a home control system with an RS232 cable. Also read the instruction manual supplied with the connected device.

AV Receiver

RS232 cable RS232 cable

Home control system TV, etc.

IR Connections



This is an example of connection to an IR receiver. Also read the instruction manual supplied with the connected device.

Ethernet cable

Screws for wall attachment

• Do not attach to the ceiling.

• After attaching, check that the fitting is secure. We accept no responsibility for damage or injury that arises due to incorrect attachment.

AV Receiver

Only when using a device that supports

PoC





Ethernet cable

AC adaptor

AV Receiver

IR Receiver

Ethernet cable

IR system cable

TV, etc.

Connect this unit to a monitor such as a TV or projector using an HDMI cable.

Connect this unit to one of our AV receivers using an Ethernet cable.

Set the ON/OFF switch on the rear of the AV receiver to ON.

Connect the AC adaptor.

4, 5.

＊

If a device that does not support Power over Cable (PoC) is connected, connect the AC adaptor to the 12V 1A INPUT jack on the rear of the unit.

Printed in Malaysia