Integra 3215, 3218, 3217 Operating Instructions Manual

Linear Stand Operating instructions

Charging Stations for Linear Stand

163952_V02

Declaration of conformity

INTEGRA Biosciences AG –

declares on its own responsibility that the devices

Description Models

Linear Stand 3215

Charging Station for Linear Stand 3217

Charging/Communication Station for Linear Stand 3218

comply with:

EU Directives (DoW: Date of Withdrawal) Before DoW DoW After DoW

Low Voltage Equipment 2006/95/EC 20.04.2016 2014/35/EU

Electromagnetic Compatibility 2004/108/EC 20.04.2016 2014/30/EU

Restriction of Hazardous Substances 2011/65/EU

Waste Electrical and Electronic Equipment 2012/19/EU

EU Regulation

Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH)

Standards for EU

Safety requirements for electrical equipment for measurement,
control and laboratory use - General requirements.

Electrical equipment for measurement, control and laboratory use ­EMC requirements.

7205 Zizers, Switzerland

1907/2006

EN 61010-1: 2010

EN 61326-1: 2013

Standards for Canada and USA

Safety requirements for electrical equipment for measurement,
control and laboratory use - General requirements.

Safety requirements for electrical equipment for measurement,
control and laboratory use - General requirements.

Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interfer­ence received, including interference that may cause undesired operation.

Zizers, December 6, 2019

Urs Hartmann
CEO

Thomas Neher
Quality Manager

CAN/CSA-C22.2

No. 61010-1

UL 61010-1

Part 15 of the

FCC Rules

Class A

Linear Stand Charging Stations - Operating instructions V02

a

Table of Contents

1 Introduction ................................................................................................................ 3

2 Installation .................................................................................................................. 3

3 Disposal ..................................................................................................................... 5

4 Accessories................................................................................................................ 5

1 Introduction

1.1 Intended use

The Linear Stand is used to hang up your INTEGRA Biosciences pipettes.

The Charging Station and the Charging/Communication Station, here Charging Stations
for short, are mounted on the Linear Stand (#3215) to charge VIAFLO/
VOYAGER Electronic Pipettes from INTEGRA Biosciences. Using the Charging/
Communication Station, the pipettes can be connected to VIALINK via a PC. VIALINK
allows the user to upload/download custom programs, images, firmware updates and
service history to and from VIAFLO and VOYAGER pipettes.

The Charging Stations have been designed for use in a laboratory. They shall be used in
a dry and dust-free location with a temperature of 5 – 40 °C and a maximal (non­condensing) relative humidity of 80 %.

1.2 Safety notes

1) Do not use the Charging Stations in an atmosphere with danger of explosion.

2) Use an original INTEGRA Biosciences Mains Adapter (#3216) only.

3) Prolonged exposure of Charging Stations to UV-light can cause discoloration and/or
yellowing of the plastic housing. This will not affect the performance of the device in any
way.

Please visit our website www.integra-biosciences.com
information regarding REACH classified chemicals contained in our products.

on a regular basis for up to date

2 Installation

2.1 Assembling the Linear Stand

Push the upper ends of the two support
feet into the connecting rail (a).

www.integra-biosciences.com 3

Linear Stand Charging Stations - Operating instructions V02

c

b

d

d

2.2 Mounting the Charging Stations

Note: The Charging Stations (#3217, #3218), Linear Stand (#3215) and Mains Adapter

(#3216) must be ordered separately.

1) Take the Linear Stand (#3215) and pull one of the two
support feet off the connecting rail.

2) Loosen the screw (b) on the Charging Station and slide
the rectangular washer (c) of the Charging Station on
the connecting rail.

3) Move the Charging Station to the desired position and
tighten the screw. Up to 4 Charging Stations can be
mounted to each linear stand.

4) Insert the plug (d) of mains adapter into the bottom of
the removed support foot and guide it through the foot.

5) Pass the cable through the horizontal slot of the

4 INTEGRA Biosciences AG

connecting rail.

6) Connect the plug (d) with the Charging Station.

Linear Stand Charging Stations - Operating instructions V02

f

e

7) Push the support foot back on the Linear Stand.

8) Connect the Charging Stations serially using the
connection cable (e).

9) Insert the plug of the USB cable (f) into the socket of
the Charging/Communication Station, if applicable.

3 Disposal

The Linear Stand can be disposed of with municipal waste. The
Charging Stations and the Mains Adapter must not be disposed of with
unsorted municipal waste. Do not dispose them in a fire.

Dispose of the Charging Stations and the Mains Adapter in accordance with the
laws and regulations in your area governing disposal of devices.

4 Accessories

Accessories Part No.

Linear Stand holds up to 4 Charging Stations 3215
Mains Adapter for use with Linear Stand (100–240 VAC, 50/60 Hz) 3216
Charging Station for

Linear Stand
Charging/Communi-

cation Station for
Linear Stand

for INTEGRA Electronic Pipettes
(incl. connection cable)

for INTEGRA Electronic Pipettes
(incl. connection cable and USB cable)

3217

3218

Imprint

© 2019 INTEGRA Biosciences AG

Manufacturer
INTEGRA Biosciences AG

CH-7205 Zizers, Switzerland
T [phone]
F [phone]
[e-mail]
www.integra-biosciences.com

www.integra-biosciences.com 5

INTEGRA Biosciences Corp.

Hudson, NH 03051, USA
T [phone]
F [phone]