Installation Instructions No. 9999-067-0
Distance between lock cover plate
3 Machine screws
Calculating the length of the connector shaft:
(Toleranz:
–
4 mm)
_________________________________________________________________________________________________
Installation Instructions CombiStar 7250 simplex and pro
The electronic lock, together with its keypad, is to be installed in accordance with the following
instructions. It should be noted that these installation instructions are a part of the VdS security
certification; failure to follow these instructions will invalidate that certification. The electronic lock is
in all cases to be protected from tampering from the outside.
Pictorial guide to installation
M6 x 35
Lock washers for
3 machine screws M6 x 35
Electronic lock CombiLock 7251
Connector shaft between
CombiLock 7251 and the
CombiControl 7238 keypad
and outside door
4 Machine screws
M4 x 10
Keypad
7238 CombiControl
Attachment ring for
CombiControl 7238
43 mm + distance between lock cover plate and outside door
_____________________________________________________________________________________________
E7250E_01.doc Rel. 1 vom 11.07.2005 1
Installation Instructions No. 9999-067-0
M
4
congruent with center line
of electronic lock
Attachment ring for
ca. 20°
attachment ring at an angle of
keypad to the right to bring it into position
this
_________________________________________________________________________________________________
Assembly sequence
Mount the attachment ring for the CombiControl 7238 keypad as shown in the sketch. Four M4
threaded holes and one hole, max. 11.4, min. 10.5 mm in diameter, will have to be tapped in the door
of the safe. Then use four M4 x 10 machine screws to mount the attachment ring, ensuring that there
is no damage in the area where the ring is secured.
CombiControl 7238 keypad
Ø92
Ø78
M4
Ø11,4 mm hole diameter
M4
Keyboard center line
M4
Positioning the keypad
Position the keypad on the
about 20° and then rotate the
_____________________________________________________________________________________________
E7250E_01.doc Rel. 1 vom 11.07.2005 2
Installation Instructions No. 9999-067-0
CombiLock 7251 electronic lock
4
1
of the CombiControl 7238 keypad
_________________________________________________________________________________________________
Tap three M6 threaded holes to attach the electronic lock as shown in the following sketch.
49,2
Three M6 threaded holes
for lock mounting
Shaft center line
67,6 mm at 9 mm extension
73,6 mm at 15 mm extension
Center line cungruent with center line
17,3
See pictorial guide for installation
1. Thread the keypad connector cable with its plug through the connector shaft and the
electronic lock’s center shaft.
2. Insert connector shaft to keypad and adjust it to electronic lock.
3. Slip-on locked electronic lock on connector shaft.
4. Use three steel machine screws (M6 x 35 or the corresponding inch threads) to affix the
electronic lock so that it is permanently and securely attached. Prevent spontaneous
loosening of these screws. It is advisable to place lock washers under the screw heads. In
order to avoid malfunctions, the mounting screws may be tightened down only to a maximum
torque of 10 Nm.
_____________________________________________________________________________________________
E7250E_01.doc Rel. 1 vom 11.07.2005 3
Installation Instructions No. 9999-067-0
for the CombiStar 7250 s
ystem
_________________________________________________________________________________________________
Installation options: The electronic lock must always be located at right angles to the keypad
(four installation positions, each offset 90° from the other).
CombiControl 7238CombiLock 7251
Sample installation
The bolt may not be subjected to tension or pressure after installation. Do not use lubricants
or any other substances on or in the electronic lock.
It is recommended that a security and functional test be made by personnel trained by cawi
after about 10,000 closing cycles.
_____________________________________________________________________________________________
E7250E_01.doc Rel. 1 vom 11.07.2005 4
Loading...