InStep Mall Cruiser 11-KS288 Operating Instructions Manual

Operating Instructions Mall Cruiser™ 11-KS288
Safety Rules:
WARNING: Failure to follow these warnings and assembly
instructions could result in serious injury or death.
· Immediately discard any plastic wrapping.
· Never allow children to fold, assemble or disassemble the stroller.
· Never place child in stroller on their back with their head forward and feet rearward.
· Avoid serious injury from falling or sliding out. Always use seat belt.
· Never leave child unattended.
· Never use this stroller with roller skates or in-line skates.
· Never allow stroller to be used as a toy or allow children to give rides to others.
· Never use stroller if it becomes damaged.
· Always be aware of traffi c around you when walking or jogging.
· Always engage brakes when you stop or when you let go of handle.
· Always use wrist strap.
· Accessories or parcels placed in or on the stroller may cause it to become unstable.
· Maximum weight for objects in back pouch is 2.2 lbs. or 1 kg. Double 2.2 lbs. or 1 kg. in each back pouch. Excessive weight may cause a hazardous, unstable condition.
· Child may slip into leg openings and strangle. Never use in a reclined carriage position unless T-shield and shoulder strap placement has been readjusted to the seat’s new position.
IMPORTANT: Read and follow these Safety Rules and Assembly Instructions before operating stroller. If you have any questions concerning the safe use of this product, contact Pacifi c Cycle at 1-800-242-6110, M-F, 8:00 a.m.-5:00 p.m. CST or visit us at www.instep.net or E-mail us at info@instep.net before using.
IMPORTANT: Tires are shipped defl ated, DO NOT OVERINFLATE. Please infl ate slowly, with short bursts, to 20-25 PSI maximum. 25 PSI will provide a comfortable ride for your child.
PLEASE DO NOT RETURN PRODUCT TO THE STORE. To ensure prompt and correct handling of problems, or to answer questions, please contact us at either our Toll-Free Customer Service number (1.800.242.6110) or E-mail us at info@instep.net. Service will be quicker if you have your model number (found on the product and box) along with this instruction sheet ready when calling. If you have any questions concerning the safe use of this product, please contact us immediately.
canopy
parent console
handle
locking pin
frame
parking brake
rear wheel
swivel lock
swivel wheel
foot plate
{Figure 1.a}
Parts List: Description Qty.
Frame assembly with seat, 1 canopy, and wrist strap
Front Wheel 1 Parent Console 1 Under-seat Basket 1 Rear Wheels 2 Front Fender 1 #8 – 11.2" Phillips head screws 4
Tools Required: Phillips screw driver, adjustable wrench.
Stroller Assembly Instructions
Unfold Stroller: Remove from carton, and remove any packaging materials that may be holding the frame in closed position. Grasp frame handle and open. Lock both plastic latches, on sides, onto the lower frame, insert locking pin into hole in latch and frame, lock the pin in place by slipping the wire loop over the end of the lock pin, repeat for the other side. {see Figure 1.A}
Rear Wheel Assembly
Grasp rear wheel in one hand, slide wheel’s axle into hole in rear of frame. Push up on the axle release lever so that the wheel is fully inserted. Pull the wheel fi rmly, the wheel should not come off if fully inserted/locked. Repeat for other side. To release wheel push up on axle release lever and pull off wheel.
Front Wheel Assembly Tip stroller back so that the handlebar is down on the ground and the front fork
is up. Attach the front wheel by loosening the wheel’s Quick Release (Q/R) lever on the front wheel far enough to allow the axle to slide into the front fork. With wheel’s Q/R lever in open position, hand tighten the cone nut until almost tight, then fl ip wheel’s Q/R lever backward to the closed position to lock wheel in place. Note this step may require minor adjustment until the Q/R lever fl ips back with fi rm pressure. Pull outward on wheel to ensure it is locked in place. (photo = open and closed lever)
Caution: The interior jam nuts are factory installed and do not need adjustment.
NOTE: This product has a swivel wheel that can rotate or be locked in place. To lock or unlock the wheel use the switch placed on the top of the fork. The wheel should always be locked in place when used as a jogging stroller. {Figure 1.a}
Front Fender Assembly
Insert the #8 – 1.5" screws into the holes located on the front support above the wheel. Align the holes on the bottom side of the fender with the screws and tighten with a Phillips screwdriver.
Parent Console Attachment
The parent console will attach to the handle by snapping it in place on the handle and above the canopy.
Operating Instructions Mall Cruiser™ 11-KS288...page 2
Front Wheel Assembly - {Figure 1.c}
axle release lever
Rear Wheel Assembly - {Figure 1.b}
quick-release
lever
(open position)
Loading...
+ 2 hidden pages