•
•
•
•
•
•
•
•
...
INSTEON On/Off
Switch
On
Status
LED
LED
-
•
•
•
•
0
•
Set Button
Tools Needed for Installation
Phillips Screwdriver
Flathead Screwdriver
Voltage Detector
Wire Cutter
I Stripper
Disconnect
Always disconnect
installation.
Support when uncertain about
installation.
Power
power
Contact
before
INSTEON
1-866-243-8022
Basic Installation
Turn off
power
your switch at the
to
0
electrical
service
panel.
or
Circuit Breakers Fuse
Panel
Power is
~
ON
~
Power is
OFF
A Remove the old switch and disconnect
V the wires. If your box lacks neutral wires,
stop and contact support.
Neutral
Wire
If·.
Turn on
use a
voltage
power
detector
at
the
circuit breaker and
multi-meter
or
identify
to
energized.
line
and
load.
Line
will
be
0
Turn off power at the circuit breaker.
Connect
the On/Off Switch wires
to
the identified wires
in
the junction box. Verify that the wire nuts are secure and that no exposed copper wire is
visible
except for the bare ground wire.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Neutral
Mount the On/Off Switch into the
junction
box
and turn power on
with the LED bar on the left
to
circuit breaker panel.
the switch at the
Test your On/Off Switch by tapping the
paddle
to
turn On and Off.
-
-
-
Linking
to
the Hub
Follow
your
On/Off
the on-screen instructions to add
the INSTEON Hub.
Switch
to
When prompted, press and
On/Off Switch's set button.
hold
the
Device Control
Turn on, turn off, set schedules and
create scenes for your On/Off Switch
using the INSTEON Hub and App.
On/Off Switch
Protected under U.S. and foreign patents (see www.insteon.com/patents)
©2014
1NSTEON RAW-1292 Rev 03.27.14
This device complies
standard(s). Operation is subject
not cause
including
harmful
interference that
with
FCC Rules
interference, and
may
and
Industry Canada license-exempt
to
the following
(2)
this device
cause undesired operation
two
conditions:
must
accept
(1)
this device may
any interference,
of
the
device.
RSS
CAUTION:
equipment,
fluorescent lighting fixture,
FCC
This device
standard(s). Operation is subject
not
cause
including interference that
Le present
appareils
suivantes:
brouillage,
subi,
Le present
appareils radio exempts
suivantes:
l'appareil
susceptible
To
reduce the risk
do
& Industry
complies with
harmful
appareil
radio exempts
(1)
l'appareil
et
(2)
mme
si
le brouillage
appareil
(1)
l'appareil
doit
accepter
d'en
of
not
install
to
control a receptacle, a motor-operated appliance, a
or
a transformer-supplied appliance.
Canada
l'utilisateur
compromettre
Compliance
FCC Rules and
interference, and
may
est conforme aux CNR d'lndustrie Canada applicables
de
licence.
ne
doit
pas produire
de
l'appareil
est susceptible
est conforme aux
de
licence.
ne
doit
pas produire
tout
brouillage radiolectrique subi,
overheating and possible
Statement
Industry
to
the
following
(2)
this device
cause undesired operation
L'exploitation est autorise aux
de
doit accepter
d'en
CNR
d'lndustrie Canada
L'exploitation
de
le fonctionnement.
Canada license-exempt
two
conditions:
must
accept any interference,
tout
compromettre le
est
autorise aux
brouillage,
damage
of
brouillage radiolectrique
et
mme
to
other
(1)
this device may
the device.
deux
conditions
fonctionnement.
applicables
deux
conditions
(2)
l'utilisateur
si
le
brouillage est
RSS
aux
aux
de
Gradateurs commandant une lampe a filament
risque
ne
flourescente ou
pas
de
surchauffe et
installer
Ia
possibilite
pour
commander
un
appareil alimente
d'endommagement
une prise, un
par
un transformateur.
de
tungstene - afin
a d'autres materiels,
appareil a moteur, une
de
reduire
lampe
le
Protected
Protege
©2014
under
U.S. and foreign patents
par des brevets americains et etrangers
INSTEON
(see
www.insteon.com/patents)
(consultez www.insteon.com/patents)
RAW-1340 Rev 03.13.14
Loading...