INSTEON LampLinc V2 2-pin 2456D2, LampLinc V2 3-pin 2456D3 Quick Start Manual
Your new INSTEONTMLamp Dimmer allows you to dim and remotely control any
lamp in your home at the touch of a button.
HINTS
• Do not use an outlet controlled by
a switch
• Be sure to leave the lamp's local
switch in the on position
• Use to control incandescent
bulbs only.
Quick-Start Guide
LAMP DIMMER
Pass-through
Outlet
Controlled
Outlet
Set Button
Status LED
Installing Your Lamp Dimmer
Smarthome Limited Warranty
Smarthome warrants to the original consumer of this product that, for a period of two years from the date of purchase, this product will be free from defects in material and workmanship and will
perform in substantial conformity to the description of the product in the owner's manual. This warranty shall not apply to defects or errors caused by misuse or neglect.
© Copyright 2005 Smarthome, 16542 Millikan Ave., Irvine, CA
92606-55027
800.SMART.HOME - 949.221.9200 - www.smarthome.com
SStteepp 11..
Two Signal Enhancers (SignaLincTMRF #2442)
must
be installed if your home does not already have them.
SStteepp 22..
Plug your lamp into the outlet at the
bottom
of the Lamp Dimmer (labeled "Controlled").
SStteepp 33..
Plug your Lamp Dimmer into an unswitched wall outlet.
SStteepp 44..
If lamp is off,
turn it on.
SStteepp 55..
Select the INSTEON Controller you would like to use and set it to Linking Mode. Refer to your INSTEON
Controller’s User’s Guide for detailed instructions.
For Models: LampLincTMV2 2-pin (#2456D2)
LampLincTMV2 3-pin (#2456D3) - pictured
NOTE:
The following will work for most INSTEON Controllers.
• On the INSTEON Controller, choose the ON/OFF Button Pair you want to use for controlling your Lamp
Dimmer.
• Set the INSTEON Controller to Linking Mode by pressing and holding the ON Button of the pair for 10
seconds.
NNeeeedd HHeellpp?? FFoorr aassssiissttaannccee ccaallll yyoouurr ffrriieennddllyy IINNSSTTEEOONN
ssuuppppoorrtt ppeerrssoonn @@ 880000-SSMMAARRTTHHOOMMEE ((880000-776622-77884466))
SStteepp 66..
Press and hold the black Set Button on the Lamp Dimmer for 3 seconds. The lamp you are controlling will
blink to confirm linking. Depending on the INSTEON Controller, you have about 4 minutes to perform this
step before setup mode times out automatically.
Congratulations! You can now dim and remotely control your lamp.
Quick-Start Guide
LAMP DIMMER
Optional If You Own an X10 Device
How to give your Lamp Dimmer an X10 address.
1. Press and hold the Lamp Dimmer’s SET button for 3 seconds, then release.
The Status LED will begin blinking.
2. Send the X10 address followed by an "ON"
THREE TIMES
from any X10 Controller within 30 seconds.
The Lamp Dimmer’s status led will blink then remain steadily on.
NNeeeedd HHeellpp?? FFoorr aassssiissttaannccee ccaallll yyoouurr ffrriieennddllyy IINNSSTTEEOONN
ssuuppppoorrtt ppeerrssoonn @@ 880000-SSMMAARRTTHHO
OMMEE ((880000-776622-77884466))
•
The Lamp Dimmer can be used with any incandescent lamp of 300 watts or less (minimum 10 watts) and should not be used with
halogen or fluorescent lighting.
• To reset the Lamp Dimmer to its original factory settings, unplug it from the wall outlet and wait 10 seconds. Press and hold its SET
button, plug it back in, continue holding the SET button for 3 seconds and release. After several seconds, the Status LED will turn on,
indicating a reset is complete.
• The advanced User's Guide can be found at
www.smarthome.com/2456d3.html
and
www.smarthome.com/2456d2.html.
Notes
Smarthome Limited Warranty
Smarthome warrants to the original consumer of this product that, for a period of two years from the date of purchase, this product will be free from defects in material and workmanship and will
perform in substantial conformity to the description of the product in the owner's manual. This warranty shall not apply to defects or errors caused by misuse or neglect.
© Copyright 2005 Smarthome, 16542 Millikan Ave., Irvine, CA
92606-55027
800.SMART.HOME - 949.221.9200 - www.smarthome.com
Optional Settings
Setting the On-Level
The On-Level is the brightness that the lamp you are controlling will go to when you turn it on using an INSTEON Controller. The OnLevel is adjustable from OFF to 100% brightness. The default is 100%.
Skip this section if you will be setting the Ramp Rate.
1. Using the ON/OFF Button Pair that you already linked LampLinc Dimmer to, set the INSTEON Controller to Linking Mode by pressing
and holding the
ON Button
of the pair for 10 seconds.
2. Using the BRIGHT or DIM Buttons on the INSTEON Controller,
adjust the brightness
of the lamp you are controlling to the desired On-
Level and tap the
SET Button
on LampLinc Dimmer
ONCE
.
3. Press and hold the black
SET Button
on LampLinc Dimmer for 3 seconds. Both the lamp you are controlling and LampLinc Dimmer’s
Status LED will blink to confirm the On-Level setting.
Setting the Ramp Rate and the On-Level
The Ramp Rate sets the time it will take for the lamp you are controlling to go from OFF to the On-Level brightness, or from the OnLevel brightness to OFF. This time is adjustable from 0.1 to 9 seconds to ramp between full-ON and full-OFF. The default is 0.5 second.
1. Using the ON/OFF Button Pair that you already linked LampLinc Dimmer to, set the INSTEON Controller to Linking Mode by pressing
and holding the
ON Button
of the pair for 10 seconds.
2. Use the BRIGHT or DIM Buttons on the INSTEON Controller to
adjust the Ramp Rate
of the lamp you are controlling. Adjust the Ramp
Rate to be faster by pressing the BRIGHT Button, or adjust it to be slower by pressing the DIM Button.
3. Tap the
SET Button
on LampLinc Dimmer
TWICE
. Both the lamp you are controlling and LampLinc Dimmer’s Status LED will blink to
confirm the Ramp Rate setting.
4. Using the BRIGHT or DIM Buttons on the INSTEON Controller,
adjust the brightness
of the lamp you are controlling to the desired On-
Level and tap the
SET Button
on LampLinc Dimmer
ONCE
.
5. Press and hold the black
SET Button
on LampLinc Dimmer for 3 Seconds. Both the lamp you are controlling and LampLinc Dimmer’s
Status LED will blink to confirm the On-Level setting.
rev. 81205
LampLincTMV2 2-pin (#2456D2) and LampLincTMV2 3-pin (#2456D3)
Loading...