INSTEON ICON In-Wall On/Off Switch, 2876S Quick Start Manual

Quick-5tart

Guide

ICON IN-WALL ON/OFF SWITCH (#28765)

Your new
ble devices in your homeatthe

ICON

On/Off

Switch allows you to control lights and other non-dimma- "X.

touchofa button.

Need Help? For assistance call your friendly support

representative

Preparation

Installation should be performed only by a qualified electrician,orby
cuitry.

If

there are any questions, consultan electrician. For setup questions contact Tech SupportatSmarthome

Tools you will need:

•A standard screwdriver.

•A Phillips screwdriver.

•A wire cutter/stripper.

Installing

Step

1.

Your

Two

Signal Extenders (#2842P)

@ 800-SMARTHOME (800-762-7846)

a homeowner who is familiar and comfortable with electrical cir-

#1

•Optional: A

• Optional: A voltage tester

• Optional: A decora wall plate if

On/Off

Switch

Phillips screwdriver

must

to

be installed if your home does not already have them.

"\.0

change the paddle color (sold separately)

identify wires inside thejunction box

you

are replacing a toggle switch

Status

LED""

r

INSTEl

I

~SETButton

for

guidance.

Step

2.

At

Step

3.

Remove the faceplate from the switch junction box, then unscrew the switch and pull it out from the junction box.

Step

4.

Disconnect the wires from the switch

Step

5. Ifyou are installing

below to identify and connect the
diagram,

•••••••••••

Main Panel 120VAC

the circuit breaker or fuse panel, disconnect the power for allofthe circuitsinthe switch junction box.

you

are replacing and ensure

the

On/Off

Switch into a two-way circuit (where one switch controls the load), follow the diagram

LINE,

LOAD,

be

sure

NEUTRAL,

you

have identified the wires correctly before connecting them.

LINE

Usually Black

GROUND

Bare

Copper

Usually

LOAD

RedorBlue

and

Non-Dimmable

Load

Appliance

GROUND

Bare

Copper

u

-

NEUTRAL

Usually White

GROUND

or

you

have

1/2"ofbare wire on

wires. If the colorsofthe wires do

NOTE

The

NEUTRAL

be connected

replacing.

wire in

sult

Smarthome Tech Support

wire will not normally
to

the

If

the

junction

an electricianorcall

800-SMARTHOME

(800-762-7846)

switch you are

there

is no

box, please con-

the

ends.

NEUTRAL

.

not

match the

Step

6.

If you are installing into a multi-way circuit (where more than one switch controls the load), consult the User's Guide.

Step

7.

Ensure

that

all wire connectors are firmly attached and

Step

8.

Orient the

Step

9.

Turn

Step

10.

Test

Step

11.

Reinstall the faceplate.

On/Off

Switch with the status

the circuit breaker backonor reinstall the fuse.

that

the

On/Off

Switch is working properlybyturning the light on and off.

that

there is no exposed copper except for the

LEDatthe left, gently place it into the junction box, then screw it into place.

GROUND

wire.

Qulck-5tart

Guide

ICON

IN-WALL

ON/OFF

SWITCH

Need Help? For assistance call your friendlysupport

representative

Using Your

•

Tap

the Paddle

•Tap the Paddle Bottom to turn your load off.

Setting

Step

1.

Step

2.

Top

Up Your

Press and hold the On/Off Switch's Paddle

Your

Select the device you would like to control and follow the setup instructions from thetable below:

In-Wall Dimmer • Press and hold the Dimmer's Paddle

PIUg-ln;,~~.mmer

On/Off Adapter • Press and hold the

@ 800-SMARTHOME (800-762-7846)

On/Off

to turn your load on.

On/Off

DevIce

'li0£:;:;,.

~:,r~

Switch

On/Off

Switch'sisnow in Linking Mode.

~:c";'

'~

t~

i\,;c'

,L

to

Control an

setup Instructions

flashes - then release.

The

On/Off

• Press and hold

trois flashes -

The

On/Off

blinks - then release.

The

On/Off

Switch will exit Linking Mode,

Switch will exit Linking Mode,

Switch will exit Linking Mode,

ICON

Top

for10seconds until its

You

the

Plug-In Dimmer's

then

release.

On/Off

have 4 minutestocomplete Step 2.

Adapter's

Device Remotely

LED

starts blinking - then release.

Top

for10seconds until the light itcontrols

and

its

LED

will stop blinking.

SET

button for 3 seconds until the lampitcon-

and

its

LED

will stop blinking.

SET

button for 3 seconds until its Status

and

its

LED

will stop blinking.

INSTEc>N

COMPATlBLE

LED

Other

ICON

Devices See device's QUick-Start GuideorUser's Guide

Step

3.

Test

that

the

On/Off Switch is working properlybyturning the load on and off.

Setting

Step

Step

Step

Up an

1.

On
blinking slowly - then release.

Your

2.

Press and hold the On/OffSwitch's Paddle

Your

3.

On

INSTEON

your Controller press and hold

Controllerisnow in Linking Mode.

Controller's

your Controller press theONand

LED

Controller

will stop blinking to indicate successful linking.

to

Control a

theONbuttonofyour choice for10seconds until the

You

have 4 minutes to complete step

Top

for10seconds until the

OFF

buttons several timestomake sure everything is working properly.

On/Off

Switch

LED

2.

LED

flashes - then release.

begins