INSTEON 2444A2WH4 User Manual

Power

Status LED

Set button

Micro-USB

Quick Start Guide

recommended that you program the unit in a quiet area.

Using RemoteLinc 2

Tap

Double-tap

Press and hold

off

released

sent and red once for each off/dim command sent.

Add RemoteLinc 2 (Button) as an INSTEON Controller

4 Scene Buttons

Right=On/brighten)

Charging LED

Owner’s Manual and Tech Support

RemoteLinc™ 2 - INSTEON® Wireless Keypad

Model: 2444A2WH4

Introduction

Conveniently control your home’s INSTEON network with the compact and versatile RemoteLinc 2 wireless keypad controller.

What's Included

• RemoteLinc 2

Getting Started

Fully charge RemoteLinc 2 prior to programming (or anytime the unit is not responding) using a Type A to Micro-B USB cable (sold separately). The red Charging LED will turn off once the battery is fully charged (approximately one hour). Slide the power switch to the ON position.

Note: RemoteLinc 2 requires an INSTEON dual-band or RF device to communicate with other devices on your INSTEON network. RemoteLinc 2 uses a subtle beeper sound to assist setup. It is

1) Tap ^ on the RemoteLinc 2 scene button of choice

2) Adjust the responder to the state you want when the scene is activated from RemoteLinc 2

3) Press and hold RemoteLinc 2's Set button until RemoteLinc 2 beeps

4) Press and hold the responder’s Set button until the responder beeps or its LED flashes

5) Confirm that scene addition was successful by tapping on/off on the programmed RemoteLinc 2 button

If the responder is a multi-scene device such as a KeypadLinc, tap the scene button you wish to control until its LED is in the desired state (on or off)

RemoteLinc 2’s Status LED will begin blinking green

RemoteLinc 2 will double-beep and its LED will stop blinking

Responder’s LED will stop blinking (it may also double-beep)

The responder will toggle between the scene’s preset on-level and off

RemoteLinc 2 contains four on/off button pairs (a-d). Each pair controls its own scene, sending commands to devices linked specifically to that on/off button pair. Dimmable responders may behave differently, depending on whether you tap, double-tap or press and hold a button to activate/deactivate a scene. Non-dimming responders will only turn full-on or full-off, no matter what method you use.

Switch

(Left=Off,

Right=On)

(Left=Off/dim,

(inside case)

Charging

Jack

Warning: RemoteLinc 2 is permanently sealed. Do not attempt to open case. Doing so will damage the remote and void the warranty.

Owner’s Manual and current Quick Start Guide: http://www.insteon.com/support Call: INSTEON Support Line at 800-762-7845

Ramp to preset on-level or

The RemoteLinc 2 Status LED will flash green once for each on/brighten command

Full-on or full-off instantly Brighten or dim until

RemoteLinc 2 Accessories

Wall Mount Bracket

Visor Clip

when you leave

Tabletop Stand

USB Charging Cable (Type A to Micro-B)

device that uses USB Type A to Micro-B

USB Power Adapter

that charges via USB cable

Pair the Wall Mount Bracket with any decorator-style

This device complies with FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful

dispositif ne doit pas causer d’interférences nuisibles, et (2) ce dispositif doit accepter toute interférence qu’il reçoit, y compris les interférences pouvant nuire à son fonctionnement.

wall plate (sold separately) for the perfect wireless

wall switch solution

(2444B4)

• Wall mount your RemoteLinc 2 anywhere

• Gang two or more together for more control

• Can be installed adjacent to existing wired-in switches

• Easily remove RemoteLinc for portability or recharging

• Use with any decorator wallplate

(Available in the 2444Bxx kit)

• Perfect for a nightstand, kitchen counter or

coffee table

• Works with RemoteLinc 2 and any other

(2444B5)

• Control your home from your vehicle

• Turn lights on when you arrive and off

• For use with RemoteLinc 2 USB

(Available in the 2444Bxx kit)

(2444B6)

Charging Cable and any other device

interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Ce dispositif est conforme aux règlements de la FCC et aux normes CNR exemptes de licence d’Industrie Canada. Son fonctionnement est assujetti aux deux conditions suivantes: (1) ce