INSTEON 2421, 2843-2 User Manual

Limited Warranty – INSTEO N warrants to original consumer of this product for a period of 2 years from date of purchase, t his product will be free from

INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 800-762-7845

Installation

Quick Start Guide

Introduction

sensor of any type (e.g., hidden contacts or doorbell button).

Complete Instructions, Troubleshooting and Tech Support

Call: INSTEON Support Line at 800-762-7845

Linking TriggerLinc as an INSTEON Controller

Main case

Magnet

Indicator

Status LED

External

Set button

Jumper

(Antenna not shown

TriggerLinc™ – INSTEON® Wireless Door Window Sensor (Open/Close)

Model: 2421/2843-2

TriggerLinc is a wireless, battery-operated magnetic contact closure
sensor. You can optionally connect an external contact closure

1) RF-only devices require at least one dual-band INSTEON device, such as an Access

Point (#2443), for communication. For the best INSTEON network performance, be sure
you have properly installed at least two dual-band INSTEON devices. Learn more about
dual-band INSTEON devices at www.smarthome.com/dualband.

2) Use a screwdriver to remove the cover of the TriggerLinc main case and install one AA

battery (included)

3) Unless the location where you plan to mount TriggerLinc is in direct view of the LED on a

dual-band device, have someone watch the LED on the nearest LED device. Then, hold
TriggerLinc in the location where you intend to mount it and tap its Set button.

4) When mounting TriggerLinc, ensure the main case and the magnet are as close to each

5) Mount the TriggerLinc magnet to the door/window as close to the edge as possible

6) Mount the TriggerLinc case to the door/window trim. If you plan to mount the unit with

7) If you plan to link responders, see Linking TriggerLinc as an INSTEON Controller and

The TriggerLinc status LED will flash once
The dual-band device’s status LED will also flash once or twice to confirm that
TriggerLinc is within range

• If the TriggerLinc Status LED doesn’t flash, replace the battery

• If the TriggerLinc Status LED flashes, but the dual-band device’s Status LED

doesn’t flash, TriggerLinc might be out of range. Try moving the dual-band
device to other locations or add additional dual-band devices.

other as possible. The magnet must be within ½” of the case to work properly. The arrows
on the side of the case and the magnet must also face each other.
Screws or double-stick tape can be used for mounting. Depending on the style of your
door or window, you might need to use the included double-stick tape beneath one of the
pieces to ensure they are at the same relative height.

Note: The included double-stick tape is very strong; you can reduce its adhesion by first
pressing it lightly against a piece of fabric or carpet.

screws, remove the battery before mounting TriggerLinc and reinstall after mounting.

replace the battery cover

arrows

sensor

terminals

for clarity)

By default, TriggerLinc will turn on responders when it opens and turn them off when it closes. For additional programming options,
see the Owner’s Manual.

1) If the default mode is desired, ensure the TriggerLinc jumper is installed. If using multi-scene mode, the jumper should be
uninstalled (or removed)

2) Set the responder to the state you wish to activate from TriggerLinc (turn it on or off, set on-level, adjust brightness, etc.).

3) Set TriggerLinc to linking mode by pressing and holding the Set button for 3 seconds

4) Press and hold the responder’s Set button for 3 seconds

5) Confirm that linking was successfully by opening and closing the magnet/sensor

TriggerLinc status LED will begin blinking

TriggerLinc status LED will stop blinking and turn on solid

Responder will respond appropriately

Owner’s Manual: www.insteon.com/support

*Setup modes will automatically time out after 4 minutes.

This device complies with FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) thi s device must accept any interference, including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.

Page 1 of 1
Rev. 07-16-2012

defects in material and workm anship and will perform in substanti al conformity with its Owner's Manual. Warranty shall not apply to defects caused by
misuse or neglect.
Protected under U.S. and foreign patent s (see www.insteon.com) © Copyright 2012