Instek Digital LCR-819, LCR-817, LCR-829, LCR-816, LCR-827 User Manual

...

LCR-800 Series User Manual

CONTENTS PAGE

1. INTRODUCTION……………………………………..……... 1

2. PRECAUTIONS BEFORE OPERATION…….……………. 2-1.Unpacking the instrument………………….……………. 2-2.Checking the Line Voltage…………………..…………… 2-3.Environment……………………………………..……….. 2-4.Equipment Installation and Operation…………………

2 2 2 3 3

3. PANEL DESCRIPTION…...……………………..………….. 4

OPERATION…………….………………………………...…. 4-1.Connects to DUT….………………..………….……..…...

4-2.Start-Up……….....……………………………..………….

4-3.Zeroing……………………………………………………. 4-4.Menu Functions.…..……………………………………… 4-5.Measurement Conditions…..……………………………..

8 8 8

8 11 18

SPECIFICATIONS…………………………………………...

6. MESSAGE CODE.………………………………………….... 44

7. MAINTENANCE....…………………………………………...

7-1.Cleaning……………………………………………………

7-2.Battery Replacement……………………………………...

7-3.Recall Calibration………………………………………...

8. OPTION 1 (BIN Function for LCR-826/827/829 only)…….. 8-1. BIN Functions for Components Sorting……………..….

8-2. BIN Setting Conditions.....……………………………….

8-3. BIN Range Setting: Component Sorting Range..............

48 48 50 56

9. OPTION 2……………………………………………………..

9-1.On-line procedure…………………………………………

9-2.RS232 VIEWER Software Operation…………………...

9-3.The Configuration of Cable………………………………

LCR-800 Series User Manual

SAFETY TERMS AND SYMBOLS

These terms may appear in this manual or on the product:

WARNING: Warning statements identify condition or practices

that could result in injury or loss of life.

CAUTION: Caution statements identify conditions or practices

that could result in damage to this product or other property.

The following symbols may appear in this manual or on the product:

DANGER ATTENTION Protective Frame or Chassis

High Voltage refer to Manual Conductor Terminal

Terminal

LCR-800 Series User Manual

iii

FOR UNITED KINGDOM ONLY

NOTE: This lead / appliance must only be wired by competent persons

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in this lead are coloured in accordance with the

following code:

Green/ Yellow: Earth

Blue: Neutral

Brown: Live (Phase)

As the colours of the wires in main leads may not correspond with the

colours marking identified in your plug/appliance, proceed as follows:

The wire which is coloured Green & Yellow must be connected to the Earth

terminal marked with the letter E or by the earth symbol

or coloured

Green or Green & Yellow.

The wire which is coloured Blue must be connected to the terminal which is

marked with the letter N or coloured Blue or Black.

The wire which is coloured Brown must be connected to the terminal

marked with the letter L or P or coloured Brown or Red.

If in doubt, consult the instructions provided with the equipment or contact

the supplier.

LCR-800 Series User Manual

This cable/appliance should be protected by a suitably rated and approved

HBC mains fuse: refer to the rating information on the equipment and/or

user instructions for details. As a guide, cable of 0.75mm

should be

protected by a 3A or 5A fuse. Larger conductors would normally require

13A types, depending on the connection method used.

Any moulded mains connector that requires removal /replacement must be

destroyed by removal of any fuse & fuse carrier and disposed of

immediately, as a plug with bared wires is hazardous if a engaged in live

socket. Any re-wiring must be carried out in accordance with the

information detailed on this label.

LCR-800 Series User Manual

EC Declaration of Conformity

GOOD WILL INSTRUMENT CO., LTD.

No. 7-1, Jhongsing Rd., Tucheng City, Taipei County 236, Taiwan

GOOD WILL INSTRUMENT (SUZHOU) CO., LTD.

No. 69 Lushan Road, Suzhou New District Jiangsu, China.

declare that the below mentioned products:

LCR-817/819/827/829/816/826/821

are herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Law of Member States relating to Electromagnetic Compatibility (89/336/EEC, 92/31/EEC, 93/68/EEC) and Low Voltage Equipment Directive (73/23/EEC, 93/68/EEC). For the evaluation regarding the Electromagnetic Compatibility and Low Voltage Equipment Directive, the following standards were applied:

EN 61326-1: Electrical equipment for measurement, control and laboratory use ––

EMC requirements (1997+A1: 1998) Conducted and Radiated Emissions EN 55011 : 1998 Group I Class A

Electrostatic Discharge

IEC 61000-4-2: 1995 Current Harmonic EN 61000-3-2: 2000

Radiated Immunity

IEC 61000-4-3: 1995 Voltage Fluctuation EN 61000-3-3: 1995

Electrical Fast Transients

IEC 61000-4-4: 1995

————————————————

Surge Immunity

IEC 61000-4-5: 1995

————————————————

Conducted Susceptibility

IEC 61000-4-6: 1996

————————————————

Voltage Dips/ Interrupts

IEC 61000-4-11: 1994

Low Voltage Equipment Directive 73/23/EEC & amended by 93/68/EEC

Safety Requirements

IEC/EN 61010-1:2001

LCR-800 Series User Manual

1. INTRODUCTION

The precise LCR meter series are automatic, user programmable instruments

that provide high reliability and great precision for measuring a wide variety of

impedance parameters. The frequency range of LCR-819/829 covers from 12Hz

to 100kHz, LCR-817/827 from 12Hz to 10kHz, LCR-816/826 from 100Hz to

2kHz, and LCR-821 from 12Hz to 200kHz. The basic accuracy is 0.1% for LCR-

827/829/816/826, 0.05% for LCR-817/819/821. The measured results can be

displayed on the high quality LCD monitor with decimal points and units. The

measured result resolution is five full digits for Inductance (L), Capacitance (C),

Resistance (R) and absolute value of impedance (|Z|) [four full digits for

Dissipation factor (D), Quality factor (Q), R with C, R with L, 2 digits after

decimal dot for phase angle (θ)]. In the meantime, the LCD monitor is also shown

the control status and parameters of settings. The keypads are easy for menu

programming. The LCR Meters’ test fixture (option) is a method of convenient,

reliable, guarded 4-terminal/2 wires connection of radial and axial leaded

components to the LCR Meters. Test conditions can be stored and recalled from

internal memory that will reduce the setup time for measurement preparing.

LCR-800 Series User Manual

2. PRECAUTIONS BEFORE OPERATION

2-1. Unpacking the instrument

The product has been fully inspected and tested before shipping from the

factory. Upon receiving the instrument, please unpack and inspect it to

check if there are any damages caused during transportation. If any damage

is found, notify the bearer and/or the dealer immediately.

2-2. Checking the Line Voltage

The LCR Meters can be operated with AC power source between 100V

rated voltage and 240V rated voltage at a frequency of 50 to 60Hz, no AC

voltage selector is necessary. Power connection to rear panel is through an

AC inlet module comprised of an AC connector and fuse holder. To change

the fuse proceed as follows:

z Remove the fuse holder by inserting a small flat head screwdriver

behind the small tab to force the holder outward.

z Install the correct fuse (slow-blow, 3A, 250Vac).

z Re-install the fuse holder back into the LCR Meters AC inlet module,

push in and lock.

WARNING: To avoid electrical shock the power cord protective

grounding conductor must be connected to ground.

WARNING: To avoid personal injury, disconnect the power cord

before removing the fuse holder.

LCR-800 Series User Manual

2-3. Environment

The normal ambient temperature range of the LCR Meters is from 10° to

50°C. To operate the instrument over this specific temperature range may

cause damage to the circuits.

Do not use the LCR Meters in a place where strong magnetic or electric

field exists as it may disturb the measurement.

2-4. Equipment Installation and Operation

Ensure there is proper ventilation for the vents in the LCR meters case. If

this equipment is used not according to the specification, the protection

provided by the equipment may be impaired.

WARNING: This is a Class A product. In a domestic environment

this product may cause radio interference in which case the user

may be required to take adequate measures.

LCR-800 Series User Manual

3. PANEL DESCRIPTION

(1). Power Switch

Turns AC Power on or off.

(2). Function key 一

Soft key functions as indicated on the adjacent LCD monitor.

(3). Function key 一

Soft key functions as indicated on the adjacent LCD monitor.

(4). Function key 一

Soft key functions as indicated on the adjacent LCD monitor.

(5). Function key 一

Soft key functions as indicated on the adjacent LCD monitor.

(6). MENU key

Enters menu display mode or exits sub menu back to main menu.

(7). Compound key

z For making numerical entries as labeled. z Turns the “RANGE HOLD” mode on or off.

(8). Compound key

z For making numerical entries as labeled. z Turns the “CONSTANT VOLTAGE” mode on or off.

(9). Compound key

z For making numerical entries as labeled. z Measures the unit of Dissipation and Quality Factor in PPM.

(Note: The models of LCR-816 and 826 do not have this function.)

LCR-800 Series User Manual

(10). Compound key

z For making numerical entries as labeled. z Selects the “INTERNAL BIAS” mode or “EXTERNAL BIAS” mode. (If

this key function is switched to “INTERNAL BIAS” mode, the bottom

of LCD monitor will display the “INT.B” message. If the external DC

bias is selected, the bottom of LCD monitor will display the “EXT.B”

message.)

(11). Compound key

z For making numerical entries as labeled. z Turns the INTERNAL BIAS mode or EXTERNAL BIAS mode “ON” or

“OFF”.

(12). Compound key

z For making numerical entries as “－“ (the negative sign). z Inputs the “TEST FREQUENCY”.

(13). START (Compound key)

z Starts measurement sequence. Normally used in the “MANU” (Triggered)

mode.

z Selects “AUTO” or “MANU” mode by pressing this key for 3 seconds at

least.

z The LCR Meters will process the measurement automatically, if the

“AUTO” mode is selected.

(14).

↵ key (ENTER)

This key enables programming of all special functions, test frequency, test

voltage, averaging, delay, and nominal value etc.

(15). ‧ Symbol key

Inputs the decimal point

LCR-800 Series User Manual

(16). Numeral key—“2”

(17). Numeral key—“3”

(18). Numeral key—“5”

(19). Numeral key—“6”

(20). Numeral key—“9”

(21). Primary Display

This line can display the measured Inductance, Capacitance, or Resistance (LCR-821 has Ζ).

(22). Secondary Display

This line can display the measured Quality Factor or Dissipation or ESR or EPR (LCR-821 has Θ).

(23). Instrument status or indicates measurement results based on entered test

limits.

(24). Test conditions

(25). Input terminals

BNC connectors, connects to device under test (DUT).

Connectors of the LCR Meters

BIAS

Lforce (current, low)

＋

Lsense (potential low)

＋

Hsense (potential high)

－

Hforce (current, high)

－

LCR-800 Series User Manual

FRONT PANEL

LCR-800 Series User Manual

4. OPERATION

4-1. Connects to DUT

The LCR Meters utilize the structure of four wires measurement which allows

accurate, easy, and stable measurements and avoids mutual inductance and

interference from measurement signals, noise and other factors inherent with

other types of connections. For the accuracy of measurement, GOODWILL

produces the cable set and test fixture (option) for connection directly to the

front panel BNC connectors.

4-2. Start-Up

Connects the power cord of the LCR Meters to the mains socket-outlet. Presses

the

POWER button of front panel to apply the AC power to the LCR Meters.

4-3. Zeroing

In order to eliminate strayed capacitance and impedance of test cable during the

measurement, the LCR Meters should be zeroed to correct for test cable and/or

test fixture errors before taking measurements. The corrections are calculated

and stored in memory of the LCR Meters during the zeroing process. Open and

short circuit zeroing should be done for test cable and/or test fixture. For the best

accuracy, the test cable and/or test fixture should be zeroed once per day at least

and each time test cable or test fixture is changed in general.

The zeroing process of open and short circuits are following:

Open Circuit

z The test cable or test fixture should be open with no component connected. z Press MENU key. z Press F1 key to select “OFFSET” menu. z Press F1 key to select open circuit zeroing (the “CAP OFFSET” is indicated

on the adjacent LCD monitor.).

LCR-800 Series User Manual

z After the BAR at the bottom of LCD monitor is filled to the full, the zeroing

process is done.

z If the zeroing process is successful, a message of “OK” will appear on the

LCD monitor. If failed, a message of “FAIL” will appear on the LCD

monitor.

Short Circuit

z The test cable should be connected or test fixture shorted (using a clean

copper wire, as short as possible).

z Press MENU key. z Press F1 key to select “OFFSET” menu. z Press F2 key to select short circuit zeroing (the “R/L OFFSET” is indicated

on the adjacent LCD monitor.).

z After the BAR at the bottom of LCD monitor is filled fully, the zeroing

process is done.

z If the zeroing process is successful, a message of “OK” will appear on the

LCD monitor. If failed, a message of “FAIL” will appear on the LCD

monitor.

Test Condition:

Test voltage=According to the actual test voltage.

Test speed = According to the actual test speed.

R.H = OFF

C.V = According to the actual test status.

For the summary, the zeroing menu can be chosen through menu selection as

shown in Figure 4-1 above.

NOTE: The “Open Circuit” and “Short Circuit” have to pass the test,

otherwise, the accuracy of the LCR Meters will become worse.

LCR-800 Series User Manual

SPEED

SLOW

DISPLAY

VALUE

MODE

L/Q

CIRCUIT

SERIES

L 1.2345H Q 0.6789

TESTING

F : 1.000 kHz V : 1.000 V

AUTO MAN U INT.B OFF

R.H OFF C.V OFF

OFFSET

SORT

SETTING

CALBRAT

EXIT

CAP. R/L OFFSET

SET SORT

SET PARAMETER

CALIBRATION

Press menu

key

Press F1 key

to the zeroing

EXIT

OPEN TEST

SHORT TEST

CAP

OFFSET

R/L

OFFSET

Press F1 KEY for

open test

Press F2 KEY for

short test

Figure 4-1: Summary of zeroing menu

LCR-800 Series User Manual

4-4. Menu Functions

All the LCR Meters’ programmable functions are controlled by the easy to use

menu displays. User can enter the menu mode by selecting the

MENU key that

calls up four top level menus, OFFSET, SORT, SETTING and CALBRAT.

Each one of these is comprised of a sub menu list whose functions are described

in detail below. User can enter one of four functions by pressing the

corresponding function key (just adjacent LCD monitor, see figure 4-2).

4-4-1. Primary & Secondary Display

For the LCR Meters, four combinations of two parameters can be measured and

displayed simultaneously. One referred to the “Primary Display” (displayed

first) and the other to the “Secondary Display”. Depending on the component

type the primary and secondary display could be L & Q, C & D, C & R or R and

Q, and add L & R and Z & θ to LCR-821. The parameter can be chosen by

pressing

F3 key as shown in Figure 4-3.

OFFSET

SORT

SETTING

CALBRAT

EXIT

CAP. R/L OFFSET

SET SORT

SET PARAMETER

CALIBRATION

Press F1 key

to the zeroing

Press F2 key

to the bin sort

Press F3 key

to the utility

Press F4 key

to the

calibration

Press MENU key

to exit menu screen

Figure 4-2: four main menu screen

LCR-800 Series User Manual

SPEED

SLOW

DISPLAY

VALUE

MODE

L/Q

CIRCUIT

SERIES

L 1.2345H Q 0.6789

TESTING

F : 1.000 kHz V : 1.000 V

AUTO MANU INT.B OFF

R.H OFF C.V OFF

Primary

Display

Secondary

Display

Figure 4-3. Primary & Secondary display

User can select R/Q for resistor measurement; select L/Q or L/R for inductor

measurement; select Z/θ for impedance measurement, select either C/D or C/R

for capacitor measurement.

Note: Only LCR-821 can select Z/θ and L/R measurement modes.

4-4-2. Series & Parallel Equivalent Circuit

Impedance that is neither a pure resistance nor a pure reactance can be

represented at any specific frequency by either a series or a parallel combination

of resistance and reactance. Such representation is called “equivalent circuit”.

The component value of the “Primary Display” depends on which equivalent

circuit (series or parallel) is chosen. In normal, the component manufacturer

shall specify how a component is to be measured (usually series) and at what

frequency. Please refer to Figure 4-4.

Press F3 key successively in order to select the different measurement mode (R/Q, C/D, C/R, L/Q, Z/θ, L/R)

LCR-800 Series User Manual

z Measurement Function

Measurement Mode Series Equivalent Circuit Parallel Equivalent

Circuit

R / Q

C / D

C / R

Z / θ (degree)

L / R

Suggested Test Conditions:

Inductors less than 10µH: Series, 100kHz.

Inductors from 10 µH to 1mH: Series, 10kHz.

Inductors from 1mH to 1H: Series, 1kHz.

Inductors greater than 1H: Series, 0.1kHz.

Capacitors less than 10pF: Parallel, 100kHz.

Capacitors from 10 to 400pF: Series or Parallel, 10kHz.

Capacitors from 400 to 1µF: Series, 1kHz.

Capacitors greater than 1µF: Series, 0.1 or 0.12kHz.

Resistor less than 1kΩ: Series, 1kHz.

Resistor from 1kΩ to 10MΩ: Parallel, 0.25kHz.

Resistor greater than 10 MΩ: Parallel, 0.03kHz

Unless for special reason, always select “Series” for capacitors and inductors.

This has traditionally been standard practice. For very small capacitance or

inductance, select a higher test frequency for better accuracy. For very large

capacitance or inductance, select a lower test frequency for better accuracy. For

dc resistance, select a lower test frequency to minimize ac effects.

Because the reactive component most likely to be represented in a low resistance

resistor is series inductance, the “Series” is selected for a resistor below about

1kΩ. If a resistor large than 10MΩ, select “Parallel” that because the reactive

component most likely to be represent in a high resistance resistor is shunt

capacitance. If the Q is less than 0.1, the measured Rp is probably very close to

the dc resistance.

LCR-800 Series User Manual

The total loss of a capacitor can be expressed in several ways, including D and

“ESR” (Equivalent Series Resistance). “ESR” is typically much larger than

actual “ohmic” series resistance of the wire leads and foils that are in series with

the heart of a capacitor physically, because ESR includes also the effect of

dielectric loss. ESR is related to D by the formula: ESR = Rs = D/ωCs. Where ω

represents “omega” = 2 pi time frequency.

Although it is traditional to measure series inductance of inductors, there are

situations in which the parallel equivalent circuit better represents the physical

component. For small “air-core” inductors, the significant loss mechanism is

usually “ohmic” or “copper loss” in the wire, therefore the series circuit is

appropriate. Nevertheless, for an “iron core”, the significant loss mechanism can

be “core loss”, therefore, the parallel equivalent circuit is appropriate which

being a better model of the inductor.

SPEED

SLOW

DISPLAY

VALUE

MODE

L/Q

CIRCUIT

SERIES

L 1.2345H Q 0.6789

TESTING

F : 1.000 kHz V : 1.000 V

AUTO MANU INT.B OFF

R.H OFF C.V OFF

Press F4 key to select the Series or Parallel circuit

Figure 4-4. Selections of Series & Parallel Circuit

LCR-800 Series User Manual

4-4-3. Measurement Displays

The measured results of the LCR Meters can be shown on the LCD monitor in

three ways: VALUE

, DELTA%, or DELTA. User can press F2 key to select the

appropriate item for measurement. Please refer to Figure 4-5.

VALUE

The LCD monitor will display the measured value of both the primary and

secondary parameter, shown with decimal and units. The resolution of primary

display (L, C, R or Z) is five digits. The resolution of secondary display (D, Q, R

with C or R with L) is four digits. The resolution of secondary display (θ) is at 2

digits after decimal point. The message “TESTING” is displayed when a test is

in process.

DELTA%

The “DELTA%” shows the percent deviation of the measured L, C, R or Z value

from a stored NOMINAL VALUE. The sign of deviation is indicated.

DELTA

The LCR difference is similar to the DELTA% except that the deviation is shown

in suitable units (ohms, henries, etc).

SPEED

SLOW

DISPLAY

VALUE

MODE

L/Q

CIRCUIT

SERIES

L 1.2345H Q 0.6789

TESTING

F : 1.000 kHz V : 1.000 V

AUTO MANU INT.B OFF

R.H OFF C.V OFF

Press F2 key to select the three different measuring display ("VALUE", "DELTA%", or "DELTA").

Figure 4-5. Types of measurement display

LCR-800 Series User Manual

4-4-4. Nominal Value

Allows entry of a “Nominal Value” for the primary parameter which is the basis

for the measurement result in “DELTA” or “DELTA %”. Accepts numerical entry

up to five digits with decimal. Units are depended on which measurement

displays selected.

Steps of “Nominal Value” input (Figure 4-6):

z Press MENU key. z Press F2 key to select “SORT” menu. z Press F1 key to select “Nominal Value” (the “NOM.VAL” is indicated on

the adjacent LCD monitor).

z Input the nominal value via the numeral keys (5 digits with decimal

maximum).

z Press ↵ key z After the BAR at the bottom of LCD monitor is filled fully, the “Nominal

Value” input is done.

4-4-5. Selection of Measurement Speed

One of three measurement speeds SLOW, MEDIUM, or FA ST could be

selected (Figure 4-7). The continuous mode speeds are about 1, 5, and 12

measurement per second respectively. The trade-off is accuracy vs. speed. LCR-

817/819 will take a more accurate measurement at a slower rate. The trade-off is

as follows

SLOW speed : More than 1 measurement per second, at 0.05% accuracy

(or better)

MEDIUM speed : More than 3 measurements per second, at 0.1% accuracy

(or better)

FAS T speed : More than 7 measurements per second, at 0.24% accuracy

(or better)

* For the details of accuracy, please refer to the specifications.

* Regarding the models LCR-826/827/829, please refer to 4-5-10 Handler

Interface Timing.

LCR-800 Series User Manual

SPEED

SLOW

DISPLAY

VALUE

MODE

L/Q

CIRCUIT

SERIES

L 1.2345H Q 0.6789

TESTING

F : 1.000 kHz V : 1.000 V

AUTO MANU INT.B OFF

R.H OFF C.V OFF

OFFSET

SORT

SETTING

CALBRAT

EXIT

CAP. R/L OFFSET

SET SORT

SET PARAMETER

CALIBRATION

Press menu

key

Press F2 key

to the sort

NOM.VAL

24.870

HANDLER

EXIT

NOM.VAL = 77.000pF

OPTION 1

Press F1 key to input the nominal value

Figure 4-6. Steps of “Nominal Value” input.

LCR-800 Series User Manual

SPEED

SLOW

DISPLAY

VALUE

MODE

L/Q

CIRCUIT

SERIES

L 1.2345H Q 0.6789

TESTING

F : 1.000 kHz V : 1.000 V

AUTO MANU INT.B OFF

R.H OFF C.V OFF

Press F1 key to select the three different measurement speed. (SLOW, MEDIUM, or FAST)

Figure 4-7. Selection of measurement speed

4-5. Measurement Conditions

4-5-1. Bias Voltage

There are two available bias voltage modes: “Internal” and “External”.

Internal:

An internal DC 2 volts bias voltage will apply to the device under test.

External:

An external DC bias voltage between 0 and 30 volts can be applied to the device

under test. The external bias connection is located on the rear panel. The

maximum current is 200mA. The supply of bias voltage has to be floating, don’t

connect either side to ground. It’s better to wait approximately 1 second for

taking a reading after initiating a testing process, therefore, the device under test

will stabilize after bias voltage applied. The DC bias voltage should be applied

only to capacitors in general. If the DC bias voltage is applied to device of low

impedance, the unreliable testing results will occur. When the external bias is

applied, please join the function of C.V.ON (Constant voltage On) in use.

LCR-800 Series User Manual

SPEED

SLOW

DISPLAY

VALUE

MODE

L/Q

CIRCUIT

SERIES

L 1.2345H Q 0.6789

TESTING

F : 1.000 kHz V : 1.000 V

AUTO MANU INT.B OFF

R.H OFF C.V OFF

Press the numerical 7 key to select either internal or external bias voltage

Press the numerical 8 key to turn either internal or external bias voltage on or off.

R.H

FREQ

C.V

2 3

PPM

5 6

BIAS

ON/OFF

S T A R T

Indication of internal or

external bias voltage

Figure 4-8. Selection of “BIAS” voltage

LCR-800 Series User Manual

Steps of “BIAS” voltage selection (Figure 4-8):

z Press compound key 7 to selects the “INTERNAL BIAS” or “EXTERNAL

BIAS” on the main menu. (If this key function is switched to “INTERNAL

BIAS”, the bottom of LCD monitor will display the “INT.B” message. If the

external DC bias is selected, the bottom of LCD monitor will display the

“EXT.B” message.

z Press compound key 8 to turn either “INTERNAL BIAS” or “EXTERNAL

BIAS” mode “ON” or “OFF” on the main menu.

4-5-2. Test Frequency

The numerical input of test frequency accepts up to 5 digits with decimal. User

can input any desired frequencies, however, the actual frequency executed for the

LCR Meters is always the closest one of the 504 available frequencies. The 504

frequencies can be calculated by the following formulas:

3kHz/n, where n range is from 13 to 250 (freq. 0.012 to 0.23077kHz)

60kHz/n, where n range is from 4 to 256 (freq. 0.23438 to 15kHz)

200kHz/n, where n range is from 1 to 13 (freq. 15.385 to 200kHz)

The “nominal value” of an available frequency can be calculated from the proper

one of the three formulas.

The range of test frequency between 12Hz and 10kHz is for LCR-817/827,

between 12Hz and 100kHz for LCR-819/829, between 100Hz and 2kHz for

LCR-816/826, and between 12Hz and 200kHz for LCR-821. To select the test

frequency, just key in the desired frequency via these numerical keys, the LCR

Meters will take the nearest available test frequency from the 504 available test

frequencies automatically.

Steps of “Test Frequency” selection (Figure 4-9):

z Press compound keyFREQ . z Input the desired frequency in kilohertz.

z Press ↵ key.

Note: After test frequency has been changed, the zeroing of “Open/Short

circuit” must be done again for the best accuracy.

LCR-800 Series User Manual

SPEED

SLOW

DISPLAY

VALUE

MODE

L/Q

CIRCUIT

SERIES

L 1.2345H Q 0.6789

TESTING

F : 1.000 kHz V : 1.000 V

AUTO MANU INT.B OFF

R.H OFF C.V OFF

Press - key to input test frequency

Press enter key to confirm the inputs.

R.H

FREQ

C.V

2 3

PPM

5 6

BIAS

ON/OFF

T A R T

test frequency

Figure 4-9. Inputs of test frequency

LCR-800 Series User Manual

4-5-3. D/Q in PPM (parts per million)(Invalid for LCR-816/826)

If the value of D or Q is less than 0.0100, user can select DQ in PPM to improve

the resolution by a factor of 100. The units of D and Q in PPM are dimensionless

and expressed as a decimal ratio with the multiplier of 1000000. User can just

press compound key

4 to select the unit of D or Q in PPM. To disable the DQ in

PPM feature, press the same key again.

4-5-4. Test Voltage

The range of test voltage is from 5mV to 1.275V in increments of 5mV. The

actual voltage through the DUT is never more than the source voltage. The DUT

impedance and the source resistance of the LCR Meters decide the actual test

voltage. The smallest voltage through the DUT will be 20% smaller of the source

voltage in general. The programming of test voltage is as follows (Figure 4-10):

z Press MENU key. z Press F3 key to select “SETTING” menu. z Press F2 key to select “VOLT” menu. z Input the desired value via the numeral keys. z Press ↵ key z After the BAR at the bottom of LCD monitor is filled fully, the “Test

Voltage” input is done.

Note: When the test frequency is at 200kHz, the test voltage must be more than

100mV.

4-5-5. Constant Voltage Source

If the DUT have to be measured at a particular test voltage, the LCR Meters

provides the constant voltage feature. After “Constant Voltage” is selected, The

LCR Meters will keep a source resistance of 25Ω. Therefore, the test voltage is

constant for any DUT impedance which large than 25Ω. If “Constant Voltage” is

selected, the measurement accuracy will cause a reduction by a factor of three.

User can just press compound key

1 to select the feature of “Constant Voltage”.

To disable this feature, press the same key again.

LCR-800 Series User Manual

SPEED

SLOW

DISPLAY

VALUE

MODE

L/Q

CIRCUIT

SERIES

L 1.2345H Q 0.6789

TESTING

F : 1.000 kHz V : 1.000 V

AUTO MANU

R.H OFF C.V OFF

INT.B OFF

OFFSET

SORT

SETTING

CALBRAT

EXIT

CAP. R/L OFFSET

SET SORT

SET PARAMETER

CALIBRATION

Press menu

key

Press F3 key to the setting

MOMORY

VOLT

1.000

AVGE

EXIT

MOMORY NO: 1

VOLTAGE = 1.000 V

AVERAGE = 1

Press F2 key to input the desired test voltage

Test Voltage

Figure 4-10. Programming of test voltage.

LCR-800 Series User Manual

4-5-6. Range Hold

If a DUT is removed from the test cable or fixture during the “Continuous” mode,

the feature of “Range Hold” can avoid range switching. Due to the test time can

be reduced, “Range Hold” is a useful utility for repetitive devices measurement.

User can just press compound key

0 to select the feature of “Range Hold”. To

disable this feature, press the same key again.

4-5-7. Averaging

If this function is enable, the testing time will multiple by the number of tests

(from 1 to 255). Hence, the accuracy can be enhanced. The measurement time

will be increased to the contrary. The programming of “Averaging” is as follows

(Figure 4-11):

z Press MENU key. z Press F3 key to select “SETTING” menu. z Press F3 key to select “AVGE” menu. z Input the desired value via the numeral keys. z Press ↵ key z After the BAR at the bottom of LCD monitor is filled to the full, the

“Averaging” input is done.

LCR-800 Series User Manual

SPEED

SLOW

DISPLAY

VALUE

MODE

L/Q

CIRCUIT

SERIES

L 1.2345H Q 0.6789

TESTING

F : 1.000 kHz V : 1.000 V

AUTO MANU

R.H OFF C.V OFF

INT.B OFF

OFFSET

SORT

SETTING

CALBRAT

EXIT

CAP. R/L OFFSET

SET SORT

SET PARAMETER

CALIBRATION

Press menu

key

Press F3 key to the setting

MOMORY

VOLT

1.000

AVGE

EXIT

MOMORY NO: 1

VOLTAGE = 1.000 V

AVERAGE = 1

Press F3 key to input the desired averaging amount

Figure 4-11. Programming of averaging.

LCR-800 Series User Manual

4-5-8. Memory

The LCR Meters have two memory functions: Recall and Store. The current

measurement conditions can be saved into the memory unit or recalled a

previously saved measurement conditions set from the LCR Meters memory.

There are 100 memory blocks totally. The programming of “Memory Store /

Recall” can be used as described below (Figure 4-12):

z Press MENU key. z Press F3 key to select “SETTING” menu. z Press F1 key to select “MEMORY” menu. z Press compound key 1 to recall a previously saved memory block. or z Press compound key 2 to store the current measurement conditions into

memory.

z Input the number of desired memory block. (1~100) z Press ↵ key

z After the BAR at the bottom of LCD monitor is filled to the full, the process

of “Memory Store/Recall” is done.

Remark: For LCR-827/829, the function of Recall and Store is not only used in

the normal memory status, also it can be extended to sorting and BIN-

SUM setting.

LCR-800 Series User Manual

SPEED

SLOW

DISPLAY

VALUE

MODE

L/Q

CIRCUIT

SERIES

L 1.2345H Q 0.6789

TESTING

F : 1.000 kHz V : 1.000 V

AUTO MANU

R.H OFF C.V OFF

INT.B OFF

OFFSET

SORT

SETTING

CALBRAT

EXIT

CAP. R/L OFFSET

SET SORT

SET PARAMETER

CALIBRATION

Press menu

key

Press F3 key to the setting

MOMORY

VOLT

1.000

AVGE

EXIT

MOMORY NO: 1

VOLTAGE = 1.000 V

AVERAGE = 1

Press F1 key to select the memory store/recall function

Figure 4-12. Programming of memory store/recall.

LCR-800 Series User Manual

MOMORY

VOLT

1.000

AVGE

EXIT

STORE NO:

VOLTAGE = 1.000 V

AVERAGE = 1

MOMORY

VOLT

1.000

AVGE

EXIT

(1)RECALL:(2)STORE

VOLTAGE = 1.000 V

AVERAGE = 1

Press compound key 1 to select the memory recall function

MOMORY

VOLT

1.000

AVGE

EXIT

RECALL NO:

VOLTAGE = 1.000 V

AVERAGE = 1

Input number of desired memory block for memory recall function

Press compound key 2 to select the memory store function

Input number of desired memory block for memory store function

Figure 4-12. Programming of memory store/recall. (Cont.)

LCR-800 Series User Manual

4-5-9. Handler Interface(Only for LCR-826/827/829)

HANDLER

INTERFACEFUNCTION

Signal Name Pin NO. Start Measurement(I) /I_E_TRIG 24 End of test(O) /O_EOM 23 Data acquisition over , DUT removal OK.(O) /O_INDEX 22 RLC FAIL(O) /O_P_HI

/O_P_LO /O_P_OVER

19 20 15

No-Go , D or Q Fail /O_S_REJ

/O_S_OVER

14 Go , BIN 1 Judgement /O_BIN_ 1 1 Go , BIN 2 Judgement /O_BIN _2 2 Go , BIN 3 Judgement /O_BIN_ 3 3 Go , BIN 4 Judgement /O_BIN_ 4 4 Go , BIN 5 Judgement /O_BIN_ 5 5 Go , BIN 6 Judgement /O_BIN_ 6 6 Go , BIN 7 Judgement /O_BIN_ 7 7 Go , BIN 8 Judgement /O_BIN_ 8 8 Go , BIN 9 Judgement /O_BIN_ 9 9 Go , BIN 10 Judgement /O_BIN_ 10 10 Go , BIN 11 Judgement /O_BIN_ 11 11 Go , BIN 12 Judgement /O_BIN_ 12 12 Go , BIN 13 Judgement /O_BIN_ 13 13 Panel Lock /I_K_LOCK 25 GND GND 16,18 VCC VCC 17

LCR-800 Series User Manual

Handler Interface Typical Electrical Characteristics

Voltage Output Rating

Comparison Signals

Low High

Maximum Current Note

/BIN1-/BIN9

/AUX_BIN

/OUT_OF_BIN

/PHI

≦0.5V +5V～+24V

5mA

/PLO

Control Signals

/INDEX

/EOM

* R408～R427 Pull-high Resistor need to be changed.

Handler Interface Typical Electrical Characteristics

Input

Input Current (Low)

Pull-high Voltage

Note

Comparison Signals

Low High +5V +12V

/EXT_TRIG

≦1V 5V～15V

5mA 12mA

/KEY_LOCK

≦1V 5V～15V

5mA 12mA

z Input Signals

/I_E_TRIG: This signal is a measurement start signal. To start

measurement by setting low pulse to minimum 5us for

/I_E_TRIG signal. This is a low edge active.

/I_K_LOCK: This signal is to lock all front panel controls. The front panel

is disable when /I_K_LOCK is at low level, and enable

when /I_K_LOCK is at high level.

LCR-800 Series User Manual

z Measurement Complete signal:

/O_INDEX: This signal will go the low level when analog measurement is

completed and will go the high level when next trigger is

active. The handler can then remove the DUT from the fixture

and replace it with another DUT during the time when

/O_INDEX is at low level.

z Compare Output Signals:

/O_BIN_1- /O_BIN_13 : The GO judgment is active according to the

measured value judgment results (low level),

for example, if the comparator assigns a

component to BIN1, the /O_BIN_1 line will go

the low level till T4 (see Handler Interface

Timing). /O_BIN_2 - /O_BIN_13 are all

inactive (high level).

/O_P_HI: Main parameter failure: When the main parameter is greater than

Max, it will go the low level till T4 (see Handler Interface

Timing).

/O_P_LO: Main parameter failure: When the main parameter is lower than

Min, it will go the low level till T4(see Handler Interface

Timing).

/O_P_OVER: It will go the low level when main parameter is greater than

Max or is lower than Min.

/O_S_REJ,/O_S_OVER: It will go the low level when secondary is greater

than D_Max (if MODE=C/D) or is lower than

D_Min.

LCR-800 Series User Manual

z Judgment Complete Signal

/O_EOM: This signal becomes active (low level) when the measurement

and comparator judgment are completed, and all handler

interface output are stable. It will go the high level when next

trigger Signal (/I_E_TRIG) becomes active (low edge).

LCR-800 Series User Manual

4-5-10. Handler Interface Timing (only for LCR-826/827/829)

* DATA: /O_BIN_1-_BIN_13,/O_P_OVER,/O_S_OVER,/O_S_REJ,/O_P_HI,/O_P_LO

LCR-800 Series User Manual

Time Minimum Value Maximum Value

Trigger Pulse Width 5 us —————

Measurement Start Delay Time 140 us —————

/EOM Delay Time After Data Output 5 us —————

Calculation and binning Time 6 ms —————

Analog Measurement Time (T5)

Trigger Wait Time

After /EOM

Output (T6)

SPEED

0.012kHz 0.1kHz 0.12kHz 1kHz 10kHz 100kHz OFF BIN VALUE

SLOW 817ms 901ms 901ms 903ms 873ms 873ms 2ms 4ms 16ms

MEDIUM 817ms 125ms 105ms 59ms 53ms 53ms 2ms 4ms 16ms

FAST 817ms 125ms 103ms 27ms 17ms 17ms 2ms 4ms 16ms

ACCURACY

MODEL

FAST MEDIUM SLOW

LCR-827 LCR-829 LCR-826

0.5% 0.2% 0.1%

LCR-800 Series User Manual

5. SPECIFICATIONS

Measurement Parameters:

Inductance (L

/Lp)*, Capacitance (Cs/Cp), Resistance (Rs/Rp), Dissipation (D),

Quality Factors (Q), Equivalent Series Resistance (ESR) and Equivalent Parallel

Resistance (EPR), Impedance (|Z|), Phase angle of Impedance [degree] (θ).

Measurement Models:

Six kinds of measurement modes can be selected. Two measurement parameters

measured and displayed simultaneously.

R/Q, C/D, C/R, L/Q, Z/θ, L/R.

Display Ranges:

Primary Display Inductance (L) : 0.00001mH ～ 99999H Capacitance (C) : 0.00001pF ～ 99999μF Resistance (R) : 0.00001Ω～99999kΩ Absolute of Impedance (Z) : 0.00001Ω～99999kΩ

Secondary Display:

Dissipation factor (D)

: 0.0001 ～ 9999

Quality factor (Q)

: 0.0001 ～ 9999

Phase angle of Impedance (degree) : -180.00∘～180.00∘

Equivalent Series Resistance (ESR)+: 0.0001Ω～9999 kΩ

Equivalent Parallel Resistance (EPR)

: 0.0001Ω～9999 kΩ

Dissipation factor (D)

in ppm : 1 ppm ～ 9999 ppm

Quality factor (Q)

in ppm : 1 ppm ～ 9999 ppm

DELTA % : 0.00001% ～ 99999%

If any of these quantities is negative, the “-“ negative indicator is displayed.

*s=series, p=parallel, ESR=Rs ** with L or R + with C Note: Only LCR-821 has Z/θ and L/R measurement parameter.

LCR-800 Series User Manual

Accuracy:

R, L, C, Z : 0.05%(Basic)+

D, Q :.0005(Basic)+ θ : 0.03∘(Basic)+

*LCR-816/826/827/829 is one fold less accuracy than LCR-817/819.

(LCR-816/826: 0.1%, LCR-827/829: 0.1%, LCR-817/819/821: 0.05%)

+: Please refer to page 39~43 for details.

Test Frequency:

There are 504 test frequencies between 12Hz and 200kHz that can be selected

by using keypad for LCR-821. The frequency range of LCR-819/829 covers

from 12Hz to 100kHz (total test frequencies: 503 points), LCR-817/827 covers

from 12Hz to 10kHz (total test frequencies: 489 points), LCR-816/826 covers

from 100Hz to 2kHz (total test frequencies: 16 points).

Measurement Displays:

The measured results can be shown on the LCD monitor in three ways:

:1. VALUE

The measured quantities of R/Q, C/D, C/R, L/Q, Z/θ, L/R.

*The resolution of primary display (L, C, R or Z) is to be five

digits.

*The resolution of secondary display (D, Q, R with C, or R with

L) is to be four digits.

*The resolution of secondary display (θ) is to be2 digits after

decimal dot.

2. DELTA %

: The DELTA% shows the percent deviation of the measured L,

C, R or Z value from a saved NOMINAL VALUE. The sign of

deviation is indicated.

:3. DELTA

The LCR difference is similar to the DELTA% except that the

deviation is shown in suitable units (ohms, henries, etc.)

Measurement Speed (LCR-816/817/819/821):

SLOW

MEDI

FAS T

896ms

286ms

135ms

*For LCR-826/827/829, please refer to 4-5-10. Handler Interface Timing.

LCR-800 Series User Manual

Equivalent Circuit:

The L, C, or R equivalent SERIES or PARALLEL circuit can be selected by

keypad.

* When select Z/θ mode, the PARALLEL circuit is invalid. Please refer to 4-4-

2. Series & Parallel Equivalent Circuit from page 12~13 for details.

Measurement Modes:

Two modes are available: AUTO and MANUAL.

“AUTO” mode is measuring continuously, updating the display after each

measurement.

“MANUAL” mode is activated by the START keypad, the measured result is

holding on the LCD monitor until next measurement started.

Average:

The AVERAGE of any number of measurements from 1 to 255 can be made as

desired in either of the two measurement modes.

Test Voltage:

The test voltage range for LCR-817/819/827/829/821 is from 5mV to 1.275V,

each step is 5mV, for LCR-816/826 is from 0.1V to 1.275V, each step is 5mV.

Note: When the test frequency is at 200kHz, the test voltage must be greater

than 100mV.

Memory:

100 memory blocks totally.

DC Bias:

A 2V internal bias can apply to capacitors during measurement.

Up to 30VDC external bias can apply to capacitors during measurement via the

two terminals (located on the rear panel). The applied current should not over

200mA.

* The external bias specified on the rear panel is at 30VDC, actually, it can be

tolerated to 35VDC.

LCR-800 Series User Manual

LCD monitor:

240×128 dot matrix C.C.F.L. back light LCD with adjustable contrast.

Battery:

DC source for system memory and calibration data backup, a replaceable 3V

lithium battery (BR-2/3A type), which probably needs to be replaced after using

for 3 years.

Every time when the battery is replaced, the LCR Meters should be recalibrated.

Operation Environment:

Indoor use,

Altitude up to 2000M

Installation Category II

Pollution Degree 2 Operating temperature: 10℃～50℃, < 85% relative humidity Storage temperature:－20℃～60℃

AC Power Source:

AC 100～240V, 50Hz～60Hz

Power Consumption:

45 Watts maximum

Fuse Replacement:

Slow-Blow, 3A, 250V

Dimensions:

330mm (W) × 149mm (H) × 437mm (D)

Wei ght:

5.5 kg

LCR-800 Series User Manual

The Error value of LCR-817/819/821 (Double the error value for LCR-

827/829/816/826)

z The formula for primary readout accuracy of C, R, L, and Z.

C: 2 counts±0.03%+0.02%[(1+Ka)# or (X/Ymax )# or (Ymin/X)# ] (1+│D│)(1+Kb+Kc)

R: 2 counts±0.03%+0.02%[(1+Ka)

or (X/Ymax )# or (Ymin/X)# ] (1+│Q│)(1+Kb+Kc)

L: 2 counts±0.03%+0.02%[(1+Ka)#or(X/Ymax)#or(Ymin/X)# ] (1+ 1 /│Q│)(1+Kb+Kc)

|Z|: Ze = Treat R, L or C as the object under test conforming above formula:

example:

When the object under test is C, select:

Ze = 2 counts±0.03%+0.02%[(1+Ka)

or(X/Ymax)#or(Ymin/X)# ] (1+│D│)(1+Kb+Kc)

When the object under test is R, select:

Ze = 2 counts±0.03%+0.02%[(1+Ka)

or(X/Ymax)#or(Ymin/X)# ] (1+│Q│)(1+Kb+Kc)

When the object under test is L , select:

Ze=2 counts±0.03%+0.02%[(1+Ka)

or(X/Ymax)#or(Ymin/X)#](1+ 1 /│Q│)(1+Kb+Kc)

z The formulas of secondary readout accuracy for D, Q, and θ.

Error

D with C

2count±0.0003 + 0.0002[(1+Ka)

or (X/Ymax) # or (Ymin/X) #] (1+│D│+D²)(1+Kb+Kc)

Q with R

2count±0.0003 + 0.0002[(1+Ka)

or (X/Ymax) # or (Ymin/X) #] (1+│Q│+Q²)(1+Kb+Kc)

Q with L

2count±0.0003 + 0.0002[(1+Ka)

or (X/Ymax) # or (Ymin/X) #] (1+│Q│+Q²)(1+Kb+Kc)

θ with Z θe=(180/π) x (Ze/100)

# 1. if X≧Ymax, please select (X/Ymax)

2. if X

≦

Ymin, please select (Ymin/X)

3. if Ymin<X<Ymax, please select (1+Ka)

4. Ze is impedance error

θe is θ error

LCR-800 Series User Manual

z The formulas for secondary readout accuracy of R with C.

Error

D≧1 2count + 0.02%[(1+Ka)* or (Rx/Rmax)* or (Rmin/Rx)*] (1+ 1/│D│)(1+Kb+Kc)+0.03%

D≦1 2count + 0.02%[(1+Ka)** or (Cx/Cmax)** or (Cmin/Cx)**] (1+ 1/│D│)(1+Kb+Kc)+0.03%

z The formulas for secondary readout accuracy of R with L.

Error

Q≦1 2count + 0.02%[(1+Ka)* or (Rx/Rmax)* or (Rmin/Rx)*] (1+ | Q│)(1+Kb+Kc)+0.03%

Q≧1 2count + 0.02%[(1+Ka)** or (Lx/Lmax)** or (Lmin/Lx)**] (1+| Q│)(1+Kb+Kc)+0.03%

*: 1. If Rx≧Rmax, please select (Rx/Rmax)

2. if Rx

≦

Rmin, please select (Rmin/Rx)

3. if Rmin<Rx<Rmax, please select (1+Ka)

**: 1. If Cx

≧

Cmax, please select (Cx/Cmax)

2. if Cx

≦

Cmin, please select (Cmin/Cx)

3. if Cmin<Cx<Cmax, please select (1+Ka)

Where

Ka: Constant Voltage factor

Constant Voltage On , Ka = 2

Constant Voltage Off, Ka = 0

Kb: Test Speed factor

Speed = SLOW , Kb = 0

Speed = MEDIUM , Kb = 3

Speed = FAST ,Kb = 10

Kc: Frequency & RMS Voltage factor (refer to Table A)

X: X is value of the component being tested.

Y: Y is range constant (refer to Table B)

LCR-800 Series User Manual

Rx and Cx are value of the component being tested.

Rmax, Rmin, Cmax and Cmin are ranges constant (refer to Table B).

Table A: (for range 1,2,3) –Kc

Voltage

Frequency

0.03≦V＜0.1 0.1≦V＜0.25 0.25≦V＜11≦V≦1.265

0.012≦F＜0.03

35 12 9 7

0.030≦F＜0.1

30 8 5 3

0.1≦F＜0.25

25 6 3 2

0.25≦F＜1

20 5 2 1

114410

1＜F≦3

15 5 2 1

3＜F≦6

15 6 3 2

6＜F≦10

15 8 5 3

10＜F≦20

20 10 6 5

20＜F≦50

30 22 18 15

50＜F≦100

50 40 35 30

200 Nonuse 80 50 45

F: test frequency in kHz

LCR-800 Series User Manual

Table A: (for range 4)-Kc

Voltage

Frequency

0.03≦V＜0.1 0.1≦V＜0.25 0.25≦V＜11≦V≦1.265

0.012≦F＜0.03

70 20 10 7

0.030≦F＜0.1

50 13 6 3

0.1≦F＜0.25

35942

0.25≦F＜1

25621

1 15410

1＜F≦3

17632

3＜F≦6

25 15 10 6

6＜F≦10

60 30 20 15

10＜F≦20

Not specified 100 65 50

20＜F≦50

50＜F≦200

This range is not used above 20kHz

F: test frequency in kHz

Table B-1: Range Hold

Inductor Capacitor Resistor/Impedance

Component

Range

Max Min Max Min Max Min

Range1 16mH /f 1mH /f 25uF /f 1.6uF /f

100Ω 6.25Ω

Range2 256mH /f 16mH /f 1600nF /f 100nF /f

1.6kΩ 0.1kΩ

Range3 4100mH /f 256mH /f 100nF /f 6.4nF /f

25.6kΩ 1.6kΩ

Range4* 65H/f 4.1H /f 6400pF /f 400pF /f

410kΩ 25.6kΩ

f = test frequency in kHz *: This range is not used above 20kHz

Table B-2: Auto Range

Inductor Capacitor Resistor/Impedance

Component

Range

Max Min Max Min Max Min

Auto range 65H /f** 1mH /f 25uF /f 400pF /f **

410kΩ** 6.25Ω**

**: Above 20kHz, Cmin = 6.4 nF/f ,and Lmax = 4100mH/f

f = test frequency in kHz.

LCR-800 Series User Manual

Example of C-D Accuracy Calculation

Measurement Conditions

Frequency: 1 kHz

Test Voltage: 1V

Test Speed=SLOW

Constant Voltage=OFF

R.H=OFF C measure: 1 μF

D measure: 0.0009

Then:

C Error = 0.03% + [0.02% x (1+ Ka) x (1+0.0009) x (1+Kb+Kc)]

=0.03%+[0.02% x (1+0) x (1.0009) x (1+0+0)]

=0.05%

±2 counts

D Error = 0.0003+[0.0002 x (1+Ka) x (1+0.0009+0.0009²) x (1+Kb+Kc)] =0.0003+[0.0002 x (1+Ka) x (1+0.0009+(0.0009²) x (1+Kb+Kc)]

=0.0003 + [0.0002 x (1+0) x (1.0009) x (1+0+0)]

=0.0005

±2 counts

Z Error = C Error = 0.05% θ Error =(180/π) x (Ze/100) =57.3∘x (0.05/100)=0.03∘

LCR-800 Series User Manual

6. MESSAGE CODE

This section describes the message code for the LCR Meters.

OVER-01

Cause:

1. If the impedance of “Device-under-test” is small than the existing

measurement range of the LCR Meters, the “OVER-01” message will be

displayed on the LCD monitor.

Calculation formula:

Capacitance: XC=1/2

Inductance: XL=2

where f=test frequency in Hz

2. If the inductor of “Device-under-test” is very large at a very high “test

frequency”, the “Resonance effect” will occur and the impedance will

decrease. Hence, the measured value is useless. Meanwhile, an “OVER-01”

message will be displayed on the LCD monitor.

Solution:

1. Turn on the “Constant Voltage” mode (please refer to 4-5-5. Constant

Voltage Source, page 22, for details).

2. Select the less measurement range. Please refer to table B-1: Range Hold,

page 42, in order to reach the exact measurement range. Turn on the “Range

Hold” mode after the measurement range fixed.

Note: Both two solutions will reduce the accuracy of the LCR Meters.

LCR-800 Series User Manual

7. MAINTENANCE

This section includes the basic maintenance information for the LCR Meters.

7-1. Cleaning

Remove the AC input power (disconnect and remove the power cord) from the

LCR Meters before attempting to clean the instrument.

To clear the LCR Meters, use soft cloth dampened in a solution of mild detergent

and water. Do not spray cleaner directly onto the instrument, since it may leak

into the cabinet and cause damage.

Do not use chemicals containing benzine, benzene, xylene, acetone, toluene, or

similar solvents.

Do not use abrasive cleaners on any portion of this equipment.

7-2. Battery Replacement

A replaceable 3V lithium battery (BR-2/3A type) supplies the backup power of

non-volatile memory for the LCR Meters. This battery probably needs to be

replaced after using for 3 years.

CAUTION: Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by

the manufacturer. Discard used batteries according to the

manufacturer’s instructions.

LCR-800 Series User Manual

7-3. Recall Calibration

When the measured value is inaccurate, you can use the Recall Calibration

function to rework by proceeding the steps as follows:

z Press MENU key. (Figure 7-1) z Press F3 key to select “SET PARAMETER” function.（Figure 7-2） z Press F4 key to select “RECALL CALIBRATION” function.（Figure 7-3） z Press compound Key 1 to select the “Yes” to start recall calibration.

（Figure 7-4）

z Press compound Key 2 to select the “No” to stop recall calibration.

(Figure 7-4)

※ If the function keys are not active, do not power off and wait another 2

minutes, then try again.

Figure 7-1

SPEED

SLOW

DISPLAY

VALUE

MODE

C/D

CIRCUIT

SERIES

C 13.450uF D .1652

TESTING

F :1.0000 kHz V :1.000 V

AUTO MANU INT.B OFF

R.H OFF C.V OFF

Press menu

key

LCR-800 Series User Manual

OFFSET

SORT

SETTING

CALBRAT

EXIT

CAP. C/D OFFSET

SET SORT

SET PARAMETER

CALIBRATION

Press F3 key to the setting

VOLT

77.000

EXIT

MEMMORY NO: 0

VOLTAGE= 1.000 V

AVERAGE= 1

RECALL CALIBRATION

Press F4 key to input the recall

function

RECALL

NOM.VAL

MEMORY

1.000

VOLT

77.000

EXIT

MEMMORY NO: 0

VOLTAGE= 1.000 V

AVERAGE= 1

RECALL CALIBRATION Are you sure?(1)Yes (2)No

RECALL

NOM.VAL

MEMORY

1.000

MEMORY

Figure 7-2

Figure 7-3

Figure 7-4

LCR-800 Series User Manual

8. OPTION 1（BIN Functions, only for LCR-826/827/829）

8-1. BIN FUNTIONS for Components Sorting:

Proceed BIN FUNTIONS steps（Figure 8-1）:

z Press MENU key. z Press F2 key to select “SORT” function. z Press F2 key to select “OPTION1 ” function.

LCR-800 Series User Manual

SPEED

SLOW

DISPLAY

VALUE

MODE

C/D

CIRCUIT

SERIES

C 13.450uF D .1652

TESTING

F :1.0000 kHz V :1.000 V

AUTO MANU INT.B OFF

R.H OFF C.V OFF

OFFSET

SORT

SETTING

CALBRAT

EXIT

CAP. C/D OFFSET

SET SORT

SET PARAMETER

CALIBRATION

Press menu

key

Press F2 key

to the sort

NOM.VAL

77.000

EXIT

NOM.VAL = 77.000pF

OPTION1

Press F2 key to

input the

option1

function

HANDLER

Figure 8-1.: OPTION 1（BIN FUNTIONS）setting

LCR-800 Series User Manual

8-2. BIN setting conditions: MODE setting：

z Press F1/F2 key to select the white inverted characters “MODE”. z Press F3 key to select C/D or C/R or L/Q or R/Q shown as Figure 8-2 below.

For further detailed description, please refer to 4-4-1.

Figure 8-2

CIRCUIT setting:

z Press F1/F2 key to select the white inverted characters “CIRCUIT”. z Press F3 key to select SER or PAR shown as Figure 8-3 below. For further

details, please refer to 4-4-2

Figure 8-3

EXIT

SET BIN BIN SUM

:C/D CIRCUIT:SER.

SPEED:SLOW DISPLAY:BIN

C D

BIN

F:1.0000kHz MANU

:1.000 V INT.B OFF RANGE:1 C.V : OFF DELAY:00000mS AVG : 1

SET

Press

key to the

mode ite

ODE

Press

to the

C/R.L/

.R/

EXIT

SET BIN BIN SUM

ODE:C/D :SER. SPEED:SLOW DISPLAY:BIN

C D

BIN

F:1.0000kHz MANU

:1.000 V INT.B OFF RANGE:1 C.V : OFF DELAY:00000mS AVG : 1

SET

Press

F1/F2

to the

CIRCUIT

PressF3ke

to the SER.

PAR

LCR-800 Series User Manual

SPEED setting:

z Press F1/F2 key to select the white inverted characters “SPEED”. z Press F3 key to select FAST, SLOW or MEDI shown as Figure 8-4 below.

For further details, please refer to 4-4-5.

Figure 8-4

DISPLAY setting:

z Press F1/F2 key to select the white inverted characters “DISPLAY”. z Press F3 key to select BIN, VAL or OFF shown as Figure 8-5 (When the

BIN is selected, BIN1~BIN13 represents PASS, while PHI, PLO, and SREJ represents FAIL result. The VAL is to display test value while the OFF represents as non-display.)

※The display speed for above three selections is different from one another.

Figure 8-5

EXIT

SET BIN BIN SUM

ODE :C/D CIRCUIT:SER. :SLOW DISPLAY:BIN

C D

BIN

F:1.0000kHz MANU

:1.000 V INT.B OFF RANGE:1 C.V : OFF DELAY:00000mS AVG : 1

SET

Press

key to the

SPEED

Press

key

to the

FAS T/ SLO W/ ME DI

EXIT

SET BIN BIN SUM

ODE:C/D CIRCUIT:SER.

SPEED:SLOW :BIN

C D

BIN

F:1.0000kHz MANU

:1.000 V INT.B OFF RANGE:1 C.V : OFF DELAY:00000mS AVG : 1

SET

Press

key to the DISPLAY

DISPLAY

Press

key

to the

VA L . O F F

LCR-800 Series User Manual

F setting (FREQUENCY):

z Press F1/F2 key to select the white inverted characters “F”. z Key-in testing frequency through panel keyboard. z Press ↵ key shown as Figure 8-6 below. For further details, please refer to

4-5-2.

Figure 8-6

V setting (VOLTAGE)：

z Press F1/F2 key to select the white inverted characters “V”. z Key-in testing voltage through panel keyboard. z Press ↵ key shown as Figure 8-7 below. For further details, please refer to

4-5-4.

Figure 8-7

EXIT

SET BIN BIN SUM

ODE:C/D CIRCUIT:SER.

SPEED:SLOW DISPLAY:BIN

C D

BIN

:1.0000kHz MANU

:1.000 V INT.B OFF RANGE:1 C.V : OFF DELAY:00000mS AVG : 1

CLR

Press F1/F2 ke

to the F

Press F3 ke

to delete the values in

in erro

EXIT

SET BIN BIN SUM

ODE:C/D CIRCUIT:SER. SPEED:SLOW DISPLAY:BIN

C D

BIN

F:1.0000kHz MANU :1.000 V INT.B OFF RANGE:1 C.V : OFF DELAY:00000mS AVG : 1

Press key to the V

Press

key to delete the values input

in erro

LCR-800 Series User Manual

INT.B setting:

z Press F1/F2 key to select the white inverted characters “INT.B”. z Press F3 or F4 key to select INT or ENT shown as Figure 8-8 below. For

further details, please refer to 4-5-1.

Figure 8-8

INT.B ON OFF setting:

z Press F1/F2 key to select the white inverted characters “ON/OFF” of INT.B. z Press F3 or F4 key to select ON or OFF shown as Figure 8-9 below.

Figure 8-9

EXIT

SET BIN BIN SUM

ODE:C/D CIRCUIT:SER.

SPEED:SLOW DISPLAY:BIN

C D

BIN

F:1.0000kHz MANU

:1.000 V OFF RANGE:1 C.V : OFF DELAY:00000mS AVG : 1

INT

Press

key

to the

INT.B

Press F3/ F4 key

to selec

INT or .EXT

EXT

EXIT

SET BIN BIN SUM

ODE:C/D CIRCUIT:SER. SPEED:SLOW DISPLAY:BIN

C D

BIN

F:1.0000kHz MANU

:1.000 V INT.B: RANGE:1 C.V : OFF DELAY:00000mS AVG : 1

Press

F1/F2 key

to the OFF

OFF

Press F3/ F4 key to select

ON or OFF

OFF

LCR-800 Series User Manual

RANGE setting:

z Press F1/F2 key to select the white inverted characters “RANGE”. z PressF3 or F4 key to select UP or DOWN value within 1~4 range shown as

Figure 8-10 below.

Figure 8-10

C.V setting:

z Press F1/F2 key to select the white inverted characters “C.V”. z Press F3 or F4 key to select ON or OFF shown as Figure 8-11 below. For

further details, please refer to 4-5-5.

Figure 8-11

EXIT

SET BIN BIN SUM

ODE:C/D CIRCUIT:SER.

SPEED:SLOW DISPLAY:BIN

C D

BIN

F:1.0000kHz MANU

:1.000 V INT.B OFF

RANGE:1

C.V: OFF

DELAY:00000mS AVG : 1

Press

F1/F2

to the C.V

Press F3/F4 ke

to selec

ON or OFF

OFF

EXIT

SET BIN BIN SUM

ODE:C/D CIRCUIT:SER.

SPEED:SLOW DISPLAY:BIN

C D

BIN

F:1.0000kHz MANU

:1.000 V INT.B OFF

RANGE:1 C.V : OFF

DELAY:00000mS AVG : 1

Press F1/F2 ke

to the RANGE

Press F3/F4

to selec

UP or DOWN

DOWN

LCR-800 Series User Manual

DELAY setting:

z Press F1/F2 key to select the white inverted characters “DELAY”. z Key-in Delay value(0~99999ms) through panel keyboard. z Press ↵ key. Please refer to Figure 8-12 below.

Figure 8-12

AVG setting:

z Press F1/F2 key to select the white inverted characters “AVG”. z Key-in average value through panel keyboard. z Press ↵ key shown as Figure 8-13 below. For further details, please refer to

4-5-7.

Figure 8-13

8-3. BIN Range Setting: Component Sorting Range

EXIT

SET BIN BIN SUM

ODE:C/D CIRCUIT:SER.

SPEED:SLOW DISPLAY:BIN

C D

BIN

F:1.0000kHz MANU

:1.000 V INT.B OFF RANGE:1 C.V : OFF

DELAY:00000mS AVG : 1

CLR

Press

key

to the DELAY

Press

key to delete the values input

in erro

EXIT

SET BIN BIN SUM

ODE:C/D CIRCUIT:SER.

SPEED:SLOW DISPLAY:BIN

C D

BIN

F:1.0000kHz MANU

:1.000 V INT.B OFF RANGE:1 C.V : OFF DELAY:00000mS

AVG: 1

CLR

Press

key

to the AVG

Press

key to delete the values input

in erro

LCR-800 Series User Manual

The step for BIN setting: (Please refer to Figure 8-14)

z When the SET BIN inverts to white character, press F3 key. z Press F3 key to select C or D sorting (The selected is a primary parameter,

the other one is an assistant parameter.)

z BIN clear setting by pressing F1 key. z Press F1 key to maintain setting, Press F2 key to delete the setting.

LCR-800 Series User Manual

EXIT

BIN SUM

MODE:C/D CIRCUIT:SER. SPEED:SLOW DISPLAY:BIN

C D

BIN

F:1.0000kHz MANU V:1.000 V INT.B OFF RANGE:1 C.V : OFF DELAY:00000mS AVG : 1

SET

SET BIN

Press F3 key

to the bin

setting

EXIT

BIN1

TOt_Bin:13

C_Nom.Val: 15.000pF

Max:16.500pF+:10.0% Min:13.500pF-:10.0%

D_Max:1.000 D_Min:.0010

SORT

Press F3 key

to sort C or D

BIN

BIN CLR

SORT BY C

Press F1 key

for clear

setting

EXIT

BIN1 NO

TOt_Bin:13

C_Nom.Val: 15.000pF YES

Max:16.500pF+:10.0% Min:13.500pF-:10.0%

D_Max:1.000 D_Min:.0010

SORT

Press F1 key for non-clear

BIN

SORT BY C

Press F2 key

for clear

setting

Figure 8-14

LCR-800 Series User Manual

Tot_BIN setting:

z Press F1/F2 key to select the white inverted characters “Tot_Bin”. z Key-in needed BIN value through panel keyboard. z Press ↵ key. Please refer to Figure 8-15 below.

Note: Tot_Bin setting: It can select ascending from 1 to 13 BIN the most. For example: If BIN1 sorting range is at

±5%, then BIN2 sorting range must

be larger than

±5%, the rest can be done accordingly.

Figure 8-15

C_Nom.Val setting:

z Press F1/F2 key to select the white inverted characters “C_Nom.Val”. z Key-in Nominal Value through panel keyboard. z Press ↵ key. Please refer to Figure 8-16 below.

Figure 8-16

EXIT

BI N 1 SORT BY C TOt_Bin:13

C_Nom.Val: 15.000pF

ax:16.500pF+:10.0%

in:13.500pF-:10.0%

D_Max:1.000 D_Min:.0010

CLR

Press

key to the

CNom.Val

EXT

BIN

Press F3 ke

can delete the

values input

in erro

EXIT

BI N 1

SORT BY C

Tot Bin:13

Nom.Val: 15.000pF

ax:16.500pF+:10.0%

in:13.500pF-:10.0%

D_Max:1.000 D

Min:.0010

Press

key

to the

Tot B in

EXT

BIN

Press

key

can delete the

values input

in erro

LCR-800 Series User Manual

Max setting:

z Press F1/F2 key to select the white inverted characters “Max”. z Key-in SORT Max value through panel keyboard. z Press ↵ key. Please refer to Figure 8-17 below.

※After the value is input, it will proceed conversion of +% automatically.

Figure 8-17

“+” setting:

z Press F1/F2 key to select the white inverted characters “+”. z Key-in the largest percentage of SORT Nominal Value through the panel

keyboard.

z Press ↵ key. Please refer to Figure 8-18 below.

※After the value is input, it will proceed conversion of Max automatically.

Figure 8-18

EXIT

BI N 1 SORT BY CTOt_Bin:13 C

Nom.Val:15.000pF

ax:16.500pF+:10.0%

in:13.500pF-:10.0%

Max:1.0000

D_Min:0.00010

Press F1/F2

key to the

Max

EXT

BIN

Press F3 ke

can delete the values

ut in erro

EXIT

BI N 1

SORT BY CTOt

Bin:13

C_Nom.Val: 15.000pF

ax:16.500pF+:10.0%

in:13.500pF-:10.0%

Max:1.0000

D_Min:0.00010

Press F1/F2

key to the

EXT

BIN

Press F3

key

to delete the values input

in erro

LCR-800 Series User Manual

Min setting:

z Press F1/F2 key to select the white inverted characters “Min”. z Key-in SORT Min value through panel keyboard. z Press ↵ key. Please refer to Figure 8-19 below.

※After the value is input, it will proceed conversion of -% automatically.

Figure 8-19

“-” setting:

z Press F1/F2 key to select the white inverted characters “-”. z Key-in the smallest minus percentage of SORT Nominal Value through the

panel keyboard.

z Press ↵ key. Please refer to Figure 8-20 below.

※After the value is input, it will proceed conversion of Min automatically.

Figure 8-20

EXIT

BI N 1

SORT BY C TOt

Bin:13

C_Nom.Val:15.000pF

ax:16.500pF+:10.0%

in:13.500pF-:10.0%

Max:1.0000

D_Min:0.00010

PressF1/F2

key to the Min

EXT

BIN

Press

key

to delete the values input

in erro

EXIT

BI N 1

SORT BY CTOt

Bin:13

C_Nom.Val: 15.000pF

ax:16.500pF+:10.0%

in:13.500pF-:10.0%

Max:1.0000

D_Min:0.00010

Press

F1/F2

key to the

EXT

BIN

Press F3

key to delete the values input

in erro

LCR-800 Series User Manual

D_Max setting：

z Press F1/F2 key to select the white inverted characters “D_Max”. z Set the largest D value of secondary parameter. Please refer to Figure 8-21

below.

Figure 8-21

D_Min setting:

z Press F1/F2 key to select the white inverted characters “D_Min”. z Set the smallest D value of secondary parameter. Please refer to Figure 8-22.

Figure 8-22

EXIT

BIN 1

SORT BY C TOt_Bin:13 C_Nom.Val: 15.000pF

ax:16.500pF+:10.0%

in:13.500pF-:10.0%

D_Max:1.0000

D_Min :0.00010

CLR

Press F1/F2

to the

Max

EXT

BIN

PressF3ke

to delete the values in

put

in erro

EXIT

BIN 1 SORT BY C TOt_Bin:13 C_Nom.Val: 15.000pF

ax:16.500pF+:10.0%

in:13.500pF-:10.0%

D_Max :1.0000

D_Min:0.00010

CLR

Press F1/F2

to the

Min

EXT

BIN

Press F3 ke

to delete the values in

put

in erro

LCR-800 Series User Manual

The other BIN setting:

z When the BIN 1 setting is finished, press F4 key to continue the BIN 2

setting until all the Tot BIN setting is completed (BIN1~BIN13 the most),

please refer to Figure 8-23.

Figure 8-23

TEST RESULT Display Summing-up:

z Press F1/F2 key to select the white inverted characters “BIN.SUM” (Figure

8-24).

z Press F3 key to see the test result.

※ Sorting judging rule: To check whether the secondary parameter is within

the setting range, if not, just display SREJ instead of judging the primary

parameter, if yes, continue to proceed primary parameter sorting.

z Press F4 key to delete test result (Figure 8-25). z Press F3 orF4 key to select delete or non-delete test result (Figure8-26). z Press F2 key to see next page of test result (Figure 8-27, 8-28).

EXIT

BI N 1

SORT BY C TOt_Bin:13

C_Nom.Val: 15.000pF

ax:16.500pF+:10.0%

in:13.500pF-:10.0%

D_Max:1.0000 D_Min:0.00010

SORT

PressF4 key

to the nex

BIN

EXT

BIN

BIN CLR

LCR-800 Series User Manual

EXIT

SET BIN

MODE:C/D CIRCUIT:SER SPEED:SLOW DISPLAY:BIN

C D

BIN

F :1.0000kHz MANU V :1.000 V INT.B OFF RANGE:1 C.V : OFF DELAY:00000mS AVG : 1

SET

BIN SUM

Press F3 key

to the test

result

PressF1.F2

key to the

BIN SUM

Figure 8-24

SORT BY C NOM_VAL:15.000pF D_MIN: .0010 D_MAX: 1.000 TEST RESULT FAIL_ITEM TOTAL PHI ( C >MAX ) PLO ( C <MIN ) SREJ( D NG ) 2 TOTAL 2

PASS_ITEM BIN 1 - BIN 13

EXIT

Press F4 to

CLR

CLR.

Figure 8-25

SORT BY C NOM_VAL:15.000pF D_MIN: .0010 D_MAX: 1.000 TEST RESULT FAIL_ITEM TOTAL PHI ( C >MAX ) PLO ( C <MIN ) SREJ( D NG ) 2 YES TOTAL 2 NO PASS_ITEM BIN 1 - BIN 13

EXIT

Press F3 to

delete the

testing data

Press F4 to

maintain the

testing data

Figure 8-26

LCR-800 Series User Manual

SORT BY C NOM_VAL:15.000pF D_MIN: .0010 D_MAX: 1.000 TEST RESULT FAIL_ITEM TOTAL PHI ( C >MAX ) PLO ( C <MIN ) SREJ( D NG ) 2 TOTAL 2

PASS_ITEM BIN 1 - BIN 13

EXIT

Press F2 to

CLR.

Figure 8-27

BIN MIN pF MAX pF TOTAL

1 13.500 16.500 999999 2 12.750 17.250 999999 3 12.000 18.000 999999 4 11.250 18.750 999999 5 10.500 19.500 999999 6 9.750 20.250 999999 7 9.000 21.000 999999 8 8.250 21.750 999999 9 7.500 22.500 999999 10 6.750 23.250 999999 11 6.000 24.000 999999 12 5.250 24.750 999999 13 4.500 25.500 999999

LAST PAGE

EXIT

Figure 8-28

LCR-800 Series User Manual

9. OPTION 2 (RS-232C: option for LCR-816/817/819, standard for LCR-821)

9-1. On-line Procedure

1) Power on the LCR METER.

Power on the RS232 function of LCR METER. With the steps as

follows (Figure 1):

z Press MENU key. z Press F2 key to select “SORT” function. z Press F3 key to select “OPTION 2” function.

z Press F1 key to select “RS232” ON.

Run PC LCR-VIEWER Program.

Check the contents of the Message area under the LCR-VIEWER to

make sure the Online Procedure has been well done. If not, select the

setting items above the LCR-VIEWER to change the Com port and

make connection again until it is online. Please refer to Figure 9-2, 9-

3, 9-4.

LCR-800 Series User Manual

EXIT

RS232 INTERFACE:ON

Press F1 key to the RS232

OFF

SPEED

SLOW

DISPLAY

VALUE

MODE

C/D

CIRCUIT

SERIES

C 13.450uF D .1652

TESTING

F :1.0000 kHz V :1.000 V

AUTO MANU I NT.B OFF

R.H OFF C.V OFF

OFFSET

SORT

SETTING

CALBRAT

EXIT

CAP. C/D OFFSET

SET SORT

SET PARAMETER

CALIBRATION

Press menu

key

Press F2 key

to the sort

NOM.VAL

77.000

EXIT

NOM.VAL = 77.000pF

OPTION2

Press F3 key to

input the

option2

function

RS232

Figure 9-1

LCR-800 Series User Manual

Figure 9-2

Figure 9-3

LCR-800 Series User Manual

Figure 9-4

5) After online, the picture of LCR Meter will be switched to “RS232

ONLINE”, please refer to Figure 9-5.

Figure 9-5

RS232 ONLINE

LCR-800 Series User Manual

9-2. RS232 VIEWER Software Operation

1) File

Press Exit（Figure 9-6）, or press Power to leave the program.

Figure 9-6

LCR-800 Series User Manual

2) Option

Settings

Port: There are three Ports available for selection including

Com1, Com2 and Com3. The default value is Com1.

Baudrate: After online, there are five Baudrates available for

selection including 9600, 19200, 38400, 57600 and

115200. The default value is 38400

。

DataBits: There are 8 bits of Data bits and User can not change it.

Parity: None. User can not change it.

StopBits: There is only 1 Bit of StopBits, and User can not change it

(Figure 9-7).

Figure 9-7

LCR-800 Series User Manual

3) Set Filename

This filename setting is the route for saving test result. Driver: Set driver

。

Directory: Set directory。

File_Name: Set file name with 4 alphabets or 4 numbers input. File_Num: Set 4 codes of file numbers from 0001 to 9999. When

the test results data reaches to the number of 10000 can be stored with a file number.

Test Resul

File_Name File_NumFilename

1-10000 LCR_ 0001 LCR_0001.Tx

10001-20000 LCR_ 0002 LCR_0002.Tx

20001-30000 LCR_ 0003 LCR_0003.Tx

30001-40000 LCR_ 0004 LCR_0004.Tx

40001-50000 LCR_ 0005 LCR_0005.Tx

50001-60000 LCR_ 0006 LCR_0006.Tx

99980001-99990000 LCR

9999 LCR_9999.Tx

FileNum Reset (refer to the following figure): File_Num is 0001.

Ps. File_Num will be continued from last file number of test result. If last file number is end at 0006, next file number is started from 0007 when re-power on the unit.

If want to start from 0001, reset the FileNum (refer to Figure 9-8).

Figure 9-8

LCR-800 Series User Manual

4) Data

Result :

Display test results. When the test results data reaches to the

number of 10000 will be stored in a file automatically. If want

to store the data less than the number of 10000, must exit the

LCR-VIEWER first (the data can be stored automatically),

then execute again the LCR-VIEWER to start another

counting of test result data. Please refer to Figure 9-9 and 9-

10.

Figure 9-9

LCR-800 Series User Manual

Figure 9-10

LCR-800 Series User Manual

9-3. The Configuration of Cable

Use the cable between DCE and DTE.

9 PIN D-SUB FEMALE to Computer (D-SUB1)

9 PIN D-SUB FEMALE to LCR Meter (D-SUB2)

D-SUB 1 D-SUB 2

Receive Data 2 3 Transmit Data

Transmit Data 3 2 Receive Data

Data Terminal Ready 4 6+1 Data Set Ready + Carrier

Detect

System Ground 5 5 System Ground

Data Set Ready + Carrier Detect

6+1 4 Data Terminal Ready

Request to Send 7 8 Clear to Send

Clear to Send 8 7 Request to Send

Instek Digital LCR-819, LCR-817, LCR-829, LCR-816, LCR-827 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual