99 Washington Street
Melrose, MA 02176
Phone 781-665-1400
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com
LEAKAGE CURRENT TESTER
GLC-9000
QUICK START GUIDE
GWINSTEK PART NO.：82LC-90000MB1
ISO-9001 CERTIFIED MANUFACTURER
This manual contains proprietary information, which is protected by
copyright. All rights are reserved. No part of this manual may be
photocopied, reproduced or translated to another language without
prior written consent of Good Will Corporation.
The information in this manual was correct at the time of printing.
However, Good Will continues to improve its products and therefore
reserves the right to change the specifications, equipment, and
maintenance procedures at any time without notice.
Good Will Instrument Co., Ltd.
No. 7-1, Jhongsing Rd., Tucheng City, Taipei County 236, Taiwan.
Table of Contents
Table of Contents
INTRODUCTION .............................................. 5
Introduction ........................................................................ 5
Front Panel .......................................................................... 6
Rear Panel ........................................................................... 8
Leakage Current Modes ....................................................... 9
Key Features ...................................................................... 10
Power and Probe Connection ............................................. 14
Preparation ....................................................................... 17
Interface ............................................................................ 19
OPERATION ................................................... 23
Measurement Terminals .................................................... 23
Non-medical Network (General Electrical Appliance) ........ 23
Medical Equipment .............................................................. 24
Leakage Current Testing Connections ................................ 25
OTHER ........................................................... 29
EUT Voltage and Current Check ......................................... 29
Voltage Measurement ........................................................ 30
3
4
INTRODUCTION
INTRODUCTION
This quick start guide is designed to help those who are not familiar
with the GLC-9000 to quickly learn the fundamentals. For details on
system settings, parameter settings, save/recall, remote instructions
and other operation features and functions, please refer to the user
manual.
Introduction
Overview
This quick start guide provides the basics on:
Front and rear panels with descriptions of all
features and functions on the panels
Description of the Leakage current modes
Basic preparation and power up
Main screen display overview
Summaries of the different leakage current
measurement operations
Summary of the EUT Voltage and Current
Check function and the Voltage Meter function.
5
GLC-9000 Quick Start Guide
Front Panel
Item Description
1. POWER
The power switch turns the power
on or off.
2. START
3. RESET
4. Display
6
: ON
: OFF
The green START button starts
measurements.
The red RESET button stops
measurements.
5.6” inch touch screen LCD display.
The touch screen display is the
primary user interface.
INTRODUCTION
5. War ning
Indicator
6. Measuring
Te rm i na l s
7. Circuit
Breaker
8. EUT AC
Te rm i na l
Block
The warning indicator lights up
when high voltages are produced
from terminals T1, T2 or T3. The
warning indicator will flash when
in standby mode.
Measuring Terminals T1 and T2 are
used to measure leakage current.
Terminal T2 has a replaceable fuse
(250V, 32mA).
The circuit breaker has over-current
protection for the EUT rated at 15A.
When testing, the warning indicator
will illuminate.
I: ON, normal operation
O: OFF, inactive or during over-
current protection.
Supplies AC power for the EUT.
Includes automatic shut-down
(circuit breaker) with over-current
protection. Maximum current
output 10A, maximum power
output, 1500VA.
9. T3 110%
Vol tag e
Application
10. USB HOST
An isolated voltage (1:1) is output to
T3 from the EUT AC IN voltage by
an isolation transformer. This
terminal is limited to medical
networks (MD:F)
USB host terminal.
7
GLC-9000 Quick Start Guide
Rear Panel
ITEM Description
1. EUT AC IN
2. RS-232
Terminal
3. USB
connector
4. EXT I/O
connector
5. GPIB
connector
6. Power Socket/
Fuse socket.
8
RS232C
EXT I/O
GPIB
EUT AC
inlet. AC voltage range:
85V～ 250V AC, 50～60Hz
10A Max
R
S-232 Interface
USB term
USB
Externa
inal for remote control.
l input/output remote
control connector.
GPIB Interfac
The power so
e for remote control.
cket accepts AC
mains power for the GLC-9000.
Power: 100V/120/220/ 230V AC
Fuse: T0.4A/250V
INTRODUCTION
Leakage Current Modes
1. Earth
Leakage
Current
2. Enclosure
Leakage
Current
3. Patient
Leakage
Current I
4. Patient
Leakage
Current II
Refers to the current that flows through a
protective grounding wire to earth. (General
Electrical, Medical Equipment)
Refers to the current that flows through a human
body in contact with a device enclosure. (General
Electrical, Medical Equipment)
Refers to the current that flows through a human
body that is directly connected to a device.
(Medical Equipment)
Refers to the current that flows through a human
body that is directly connected to a device under
faulty conditions.
(Medical Equipment)
9
GLC-9000 Quick Start Guide
5. Patient
Leakage
Current III
6. Patient
Auxiliary
Current
Refers to the current that flows through a human
body that is directly connected to a device that
malfunctions.
Refers to the current that flows through a human
and a device during normal operation. This is not
intended to be perceptive. (Medical Equipment)
Key Features
International
Standards and
Regulations
The GLC-9000 has nine measurement networks
(Measuring Devices: MD) supporting GB/12113,
IEC/UL and other international standards for
electrical products:
(1) MD-A:IEC60990
(2) MD-B:IEC60990
(3) MD-C:IEC60990
(4) MD-D:UL
(5) MD-E(1kΩ):-general application
(6) MD-F: Medical
(7) MD-G:UL
(8) MD-H:(2kΩ)-general application
(9) MD-I:JIS
(Medical Equipment)
10
Loading...