Instanta DB2000 Installation And User Instructions Manual

The Professional’s Choice
DB2000 Push Button Dispense Boiler
Installation And User Instructions
CONTENTS
CONTENTS & INTRODUCTION 2
SAFETY INFORMATION 2
ENVIRONMENTAL INFORMATION & DELIVERY CHECKLIST 3
TECHNICAL SPECIFICATION 3
OPERATION 4
DAILY USE 4
ECO POWER SAVING 4-5
PROGRAM MODE 5-6
CLEANING 6
MAINTENANCE, & SERVICE INFORMATION 6
SERVICE WARNINGS & FAULT DIAGNOSIS 6-7
TECHNICAL SUPPORT 8
GUARANTEE 8
Introduction
Dear Customer,
Thank you for purchasing this Instanta product.
Your new Instanta Boiler is designed to give years of trouble-free service provided that the instructions contained in this manual are followed.
All new Instanta products are energy effi cient, simple to operate and easy to service.
Safety Information
Please read the following carefully before starting work on this equipment.
A competent installation engineer should install this appliance in accordance with the installation instructions for this appliance and all relevant local and national standards including the following:
�• Health and Safety at Works Act
�• IEE regulations
�• Local and national building regulations
�• BS Codes of practice
�• Water supply regulations
VERY HOT WATER - Your new DB2000 Push Button Dispense boiler is designed to provide a constant source of near boiling water, which can be dispensed for the preparation of hot drinks.
The LCD display on the front of the appliance shows the message “Very Hot Water!” whenever a drink is dispensed, warning users to take caution. Nevertheless, if deemed necessary, an additional warning notice displayed adjacent to the boiler may be helpful in notifying users that the appliance contains and dispenses near boiling water.
The DB2000 is ideal for self-service however the boiler also has an optional programmable locking system, which can restrict its use where Health and Safety is a concern or in High Security environments.
In line with Health and Safety requirements it is advisable that a risk assessment be carried out after the boiler has been installed.
2
Environmental Information
Information on Disposal for Users of Waste Electrical & Electronic Equipment
The “crossed out wheelie bin” symbol on this product means that discarded electrical and electronic products should not be mixed with general waste. Disposing of the product correctly will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For proper treatment, recovery and recycling of end-of-life products, please contact your dealer or supplier for further information, or local authority for details of your nearest designated collection point.
Checklist
Before starting installation check that you have the following parts:
1. Drip Tray
2. Front Overflow Blanking bung
3. Flexible (WRAS approved) Water Hose
4. Programmable key (Optional locking system)
Technical Information
Outer casing and tank constructed in Type-304 stainless steel. Internal baffle-plates [for condensing steam within the tank] are made from Type-316 stainless steel. The tank is fully insulated with FR high-temperature polystyrene.
All boilers have electronic control of the main functions. This means that the temperature is controlled precisely within given parameters. The circuit constantly monitors the operation of the machine and warns the user via the display panel if any abnormal circumstances have been detected.
Description: Push-button type Dispense Water Boiler
Model Ref No: DB2000
Voltage: 230V single-phase 50/60Hz
Supply: AC
Rated Input: 3.0kW
Fill Type: Automatic
Max Rapid Draw-Off: 12 Litres [72 x 150ml cups]
Recovery per Minute: 0.5 Litres
Recovery to full Capacity: 24 minutes
Temperature: Adjustable between 80 - 99^C (factory-set @ 97^C)
Heat up time from Cold: 32 Minutes (to full boiler capacity)
Dimensions/Weight:
Height: 608mm
Width: 260mm
Depth (including drip-tray): 465mm
Tap clearance: 145mm
Weight (empty): 14.0kg
Weight (full): 30.0kg
3
Loading...
+ 5 hidden pages