Instanta CPF2100, CPF210, CPF310, CPF4100-3, CPF4100-6 Installation And User Instructions Manual
...
CPF Series
Models: CPF2100, CPF210, CPF310,
CPF4100-3, CPF4100-6 & CPF6100
Auto-Fill Catering Water Boiler
With Integrated Multi-Filter
Installation And User Instructions
The Professional’s Choice
INSTANTA LIMITED
Canning Road, Southport, Merseyside,
PR9 7SN
Tel: (01704) 501114 Fax: (01704) 501115
IB30 - ISS: 01
CONTENTS
CONTENTS & INTRODUCTION 1
SAFETY, ENVIRONMENTAL INFORMATION & DELIVERY CHECK-LIST 2
TECHNICAL SPECIFICATION 3
INSTALLATION 3
OPERATION (including set-up of clock time) 4
ECO MODE / ENERGY SAVING 5
DAILY USE 5
MULTI-FILTER & FILTER REPLACEMENT 5
ADJUSTING FILTER-MONITOR (optional) 7
SEVEN-DAY TIMER 8
CLEANING 9
MAINTENANCE, SPARES & SERVICE INFORMATION 9
SERVICE WARNINGS & FAULT DIAGNOSTICS 10
SERVICE / TECHNICAL SUPPORT 11
GUARANTEE 11
Introduction
Dear Customer,
Thank you for purchasing this Instanta product.
Your new water boiler is designed to give you years of trouble-free service provided that the
instructions contained in this manual are followed.
All new series Instanta products are energy efcient, simple to operate and easy to service.
Find out more about Instanta products at www.instanta.com
1
Safety Information
Please read the following carefully before
starting work on this equipment.
A competent person should install this appliance
in accordance with the installation instructions
for this appliance and all relevant local and
national standards including the following:
• Health & Safety at Work Act
• IEE Regulations
• Local & National Building Regulations
• BS Codes of Practice
• Water Supply Regulations
All personnel should be provided with sufcient
training in the safe use of this appliance.
• Inform users that certain surfaces will
become hot (especially the draw-off tap).
Care should be taken to avoid potential
injury from burns and scalding whilst
operating this appliance.
• In line with Health and Safety requirements
we recommend a risk assessment be carried
out after the boiler has been installed.
• Always disconnect the unit from the power
supply before servicing.
• The unit must be earthed.
• Keep these instructions in a safe place near
the unit for future reference
Environmental
(Information On Disposal
For Users Of Waste Electrical
& Electronic Equipment)
The “crossed out wheelie bin” symbol on
this product means that discarded electrical
and electronic products should not be mixed
with general waste. Disposing of the product
correctly will help to save valuable resources
and prevent any potential negative effects
on human health and the environment which
could otherwise arise from inappropriate waste
handling. For proper treatment, recovery and
recycling of end-of-life products, please contact
your dealer or supplier for further information,
or local authority for details of your nearest
designated collection point.
Delivery Checklist
Before starting installation, check that you have
the following parts;
• Catering Water Boiler
• Drip-tray
• Rubber tapered over-ow bung
(use when directing over-ow to permanent
waste at rear)
• White water inlet hose (3/4”BSP connection)
• User instructions
2
Technical Specification
Model CPF2100 CPF4100-3 CPF4100-6 CPF6100 CPF210 CPF310
Width mm 260 360 360 440 260 260
Depth mm 555 555 555 555 555 555
Height mm 610 610 610 610 705 705
Tap Clearance mm 200 200 200 200 300 300
Power Rating KW 3.0 3.0 6.0 6.0 3.0 6.0
Weight (Empty) KG 15.3 18.5 18.8 21.4 16.3 16.8
Weight (Full) KG 29.1 40.0 40.3 53.0 30.1 30.6
Water Inlet Pressure: Bar 2 to 7 2 to 7 2 to 7 2 to 7 2 to 7 2 to 7
Installation
The boiler must be installed on a horizontal work
surface with sufcient strength to support its
weight.
Locate in an area where there is adequate space
to use the boiler safely (e.g. free from risk of
congestion and tripping hazards).
Connection to Mains Water Supply:
Connect the WRAS approved water lling hose
(3/4”BSP) to the inlet connection point on the
back of the boiler and the other end to the mains
water supply, via an accessible isolating tap with
a ¾”BSP thread.
IMPORTANT: If micro-bore pipe is used
instead of the inlet hose supplied, the size
must be minimum OD 3/8”(10mm).
The water supply must have a pressure not
exceeding 7bar (96psi), and no lower than 2bar
(28psi) NOTE: If your water pressure exceeds
7bar, t a suitable pressure reduction valve.
We regret that Instanta cannot be held
responsible for any machine malfunctions if
the water pressure exceeds that stated. If in
doubt, consult your water supply company
Electrical Connection:
The boiler must be Earthed.
All 3.0KW models:
Your machine is supplied with a standard 13amp
bonded plug with a 13amp fuse.
All 6.0KW models:
Your machine is supplied with a 1.5mtr cord
(3-core @ 2.5mm). Wire to at least a 30amp
supply via an all-pole disconnection isolator
switch (easily accessible for safety). Only a
qualied electrician should undertake this work.
Overflow:
The drip-tray has a limited capacity and is
designed to handle small spillages and drips.
Wherever possible, we strongly recommend that
it is connected to a permanent waste.
We have provided two overow outlet/
connection points to choose from;
1). FRONT via drip-tray
If this option is used for the overow, we
can supply a 15mm tting kit (Pt. No: DTK2)
available from Instanta Spares Department
(01704 502905).
2). REAR via outlet at back of machine
If rear overow option is preferred, the front
overow-outlet (see diagram below), must be
blocked off using the tapered–rubber blanking
bung provided. Pipework should then be
provided between the back of the machine
[1/2”bsp – 15mm], and a suitable waste/drain.
NOTE: An air gap must be provided within
300mm of the connection point. Failure to
provide an air gap within this distance could
cause an air lock which could stop the water
discharging in the event of an overow.
3
Loading...