Cnct | intelliPLUG Quick Start
Guide
app.cnct.com
Cnct-Quick-Guide_v2-.indd
2
2017/4/21
10:25:56
Quick Start Guide
Cnct-Quick-Guide_v2-.indd
3
2017/4/21
10:25:56
Get To Know Your
intelliPLUG
Compact Design
Actual Size
Wi-Fi Enabled
Power
Button
Control Appliances
and Devices with App
Compatible with
Standard Outlet
Electrical Ratings
••AC 120V, 60 Hz
15A
1800 W
For general use only
Cnct-Quick-Guide_v2-.indd
4
2017/4/21
10:25:56
Cnct-Quick-Guide_v2-.indd
5
2017/4/21
10:25:56
Quick Start Guide
1.
Download the Cnct app.
•Go to http://app.cnct.com to install the free Cnct app for
your phone or tablet.
•Once installed, follow the steps to setup your Cnct
account.
2.3.Ensure your phone (or tablet) and intelliPLUG
are connected to the same Wi-Fi network
•Must be a 2.4 GHz Wi-Fi network
Plug in your intelliPLUG. Once plugged in, the power button
will begin flashing a blue light; indicating it is ready for
setup. From the Cnct app, click the “ ”icon in the upper
right hand corner, select the intelliPLUG device, enter your
Wi-Fi password, and begin setup. Once setup is complete,
the blue light will stop flashing and you will be prompted to
create a name for your intelliPLUG. If the setup fails, reset
the intelliPLUG and go through the setup process again
(see below).
How To Reset intelliPLUG
When plugged in, press and hold the power button on the side of
your intelliPLUG for 4 seconds until the blue light begins flashing.
Use the Cnct app to reconfigure the network settings.
Safety Warnings:
•
Plug directly into electrical outlet
(Do not use an extension cord)
•
•
•
•
•
•
For indoor use only
Remove intelliPLUG from outlet before cleaning
Do not clean with liquid
Do not remove ground pin (middle pin)
Do not use in wet or damp areas
Keep children away from intelliPLUG and outlet
Do not exceed the recommended electrical ratings
Do not use in precision timing applications where
inaccurate timing could be dangerous
(Example: sunlamps, saunas, etc.)
•
Do not use with devices that should not be operated
without supervision
Operating conditions:For in door use only
Electrical ratings
Model No.
Volt.
Output
Load Type
Complete Declar.
(i.e. 1.C.L, etc.)
intelliPLUG
120 V,
60Hz
15 A
Resistive
Type 1.B, Operating
15 A
General Use
600 W
Tungsten
500 VA
Electronic Ballast
1/2 hp
Horse Power
Type of Action:Type of 1.B
FCC Statement
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment must be installed and
operated in accordance with provided instructions and the
antenna(s) used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and(2) this
device must accept any interference received, including interference
that may cause undesired operation.
Caution!
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
Canada Statement
This device complies with Industry Canada’s licence-exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and(2) This device must
accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
The device meets the exemption from the routine evaluation limits
in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure,
users can obtain Canadian information on RF exposure and
compliance.
Le dispositif rencontre l'exemption des limites courantes
d'évaluation dans la section 2.5 de RSS 102 et la conformité à
l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information
canadienne sur l'exposition et la conformité de rf.
This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter. This equipment should be
installed and operated with a minimum distance of 20 centimeters
between the radiator and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même
temps qu'aucune autre antenne ou émetteur. Cet équipement devrait
être installé et actionné avec une distance minimum de 20
centimètres entre le radiateur et votre corps.
Loading...