Insinger Machine Co G-15 DISPOSER, G-1000L-3 User Manual

DESIGN
The “G” Series is recommended for handling huge quantities of the heaviest and toughest material encountered in central food waste areas. The extra-large 15” rotor with the 7 1/2 HP motor generates maximum centrifugal force and impact disintegration speed. The Series “G” easily disposes all general heavy/waste including big steer rib, leg or knuckle bones (even raw), lobster shells, poultry carcasses, fish heads, pineapples and regular or wax-coated paper waste.
SERIES G 15” RO T OR
COMMERCIAL FOOD WASTE DISPOSER
STANDARD EQUIPMENT
• 7 1/2 HP motor
6245 State Road Philadelphia, PA 19135-2995 215-624-4800 215-624-6966 FAX
800-344-4802
www.insingermachine.com
OPTIONAL EQUIPMENT
• Stainless steel cone or sink attachment (includes vinyl silver trap ring, solenoid valve, flow control valve, vacuum breaker)
• 10 HP motor- heavier duty
• Offset-body for maximum space utilization, also available for both cone & sink attachments
• Cones 12”, 15” & 18”
NOTE: Sink attachments and s/s cones need to be welded into table
O style- Optional off-set body for use with bowl/cone trough
Note: For all rough in connections see installation and layout detail drawing
G-15 DISPOSER
DESIGN AND CONSTRUCTION
• Waste chamber design permits dual directional operation when used with reversing control or switch, doubling the life cycle of the shattering mechanism.
• Basic body components are cast gray iron, machined, primed and painted. 15” diameter rotor with (2) bolt-on reversible impact bars and sizing ring are cast ductile iron, machined, balanced and heat treated.
• Access to waste chamber by means of a cast aluminum lid having a 7” diameter throat opening, removable by means of quick-release head clamps.
• Flexible drain connector. Fastens quickly to either metal or PVC drain line (3” pipe size).
• Stainless steel legs and feet, adjustable from 0” to 2”.
• Disposer connects to cone or sink assembly by means of a neoprene isolation sleeve and (2) stainless steel clamps.
• Offset Design: For maximum space utilization, disposer is also available with an 10 1/2” off-set waste chamber for both cone and sink attachments.
MOTOR
• Reversing, continuous duty, 1725 RPM (1425 RPM, 50 Hz), full rated horsepower, double sealed, permanently lubricated ball bearings.
• Thermal overload protection (heaters) in control; must be sized as required.
• Available in 7 1/2 and 10 HP, 3 Phase.
• Dual voltage winding: 208-230/460 Volts, 60 Hz
190/380 Volts, 50 Hz
(See table for ampere draw per horsepower, volts & phase)
CONTROLS
Electrical switches or control centers not included, must be selected as required. Note: All plumbing and electrical connections should be made according to local codes.
HP
THREE PHASE
Volts Amps*
7 1/2
208 230 460
23.0
22.0
6.8
10
208 230 460
33.0
30.0
15.0
*Ratings are for 60 Hz operation.
1” Min. 6” Max.
Cutout
1” Min. 6” Max.
10 1/2”
Disposer shown with regular drum
and sink mounting assembly
Note: All dimensions shown at 0” foot height adjustment
8” length of neoprene connector sleeve furnished. May be cut to desired length.
Adjustable 0” to 2”
Disposer shown with offset drum and
cone mounting assembly
Table Cutout 13” for 12” cone 16” for 15” cone 19” for 18” cone
1”
1”
10 1/4”
8”
12 1/2”
11”
1”
4 3/4” for 12” cone 5 1/2” for 15” cone 6 1/4” for 18” cone
10 1/4”
11”
Adjustable 0” to 2”
13 1/2”
22 1/2”
(26 1/2”)
12 1/2”
7”
8”
Water
inlet
Drain
Drain
Water
inlet
13 1/2”
27”
Loading...