Insignia NS-WSCN User Manual
Quick Setup Guide
|
NS-WSCN
Remote Wireless Shutter Control for Nikon DSLR Cameras
Thank you for purchasing this high-quality Insignia
infrared shutter control for your Nikon DSLR camera.
Your shutter control triggers your camera’s shutter when
using slow shutter speeds. Because you do not touch
your camera when using your shutter control, you
experience less camera vibration and get sharper
pictures. Your shutter control is especially useful for
taking self-portraits.
PACKAGE CONTENTS
• Remote Wireless Shutter Control with battery
• Lanyard
• Quick Setup Guide
Scan for compatibility chart
Before using your new product,
please read these instructions to prevent any damage.
FEATURES
Shutter button
BATT.
Plastic insulation
sheet
Battery holder
USING YOUR REMOTE CONTROL
1 Pull the plastic insulation sheet out of your shutter
control before using it the first time.
2 Set your camera to IR mode. For instructions, see the
documentation that came with your camera.
3 Attach your camera to a tripod, or place it on a steady
surface like a shelf or table.
4 Point your shutter control directly at your camera’s IR
receiver, then press the shutter button on the front of
your shutter control. When your camera receives the
IR signal, it automatically focuses and takes a picture.
TROUBLESHOOTING
If your camera does not focus and take pictures:
• Make sure that your shutter control is within
32.8 ft (10 m) of the camera’s IR receiver.
• Make sure that your camera is in IR mode. See your
camera’s user manual to activate the IR mode.
• Make sure that your camera has an autofocus feature.
See your camera’s user manual to activate auto focus
(if available).
• Make sure that the battery for the shutter remote
control is not expired. Replace with a CR2025 battery
if necessary.
• Make sure the line of site between the transmitter and
the infrared receiver is not blocked by the lens or
other obstacles.
REPLACING THE BATTERY
1 Push the release tab (1) in the direction of the arrow.
2 Pull the battery tray (2) out of the battery
compartment.
3 Remove the old battery, then insert a new CR2025
battery face up into the tray.
4 Push the battery tray into the battery compartment
until the tray locks in place.
SPECIFICATIONS
Model: NS-WSCN
Operating voltage: 3V (Battery: CR2025)
Operating temperature: 14° ~ 122°F (-10° ~ 50°C)
Standby current: 1.2μA
Transmitting angle: 30°
Wavelength: 940 nm
Maximum operating
distance: 32.8 ft. (10 m)
Carrier frequency: 38.1 KHZ
Dimensions (L×W×H): 2.6 × 1.2 × 0.3"
(6.7 × 3.1 × 0.7 cm)
Weight: 0.4 oz (12 g)
SAFETY INFORMATION
FCC Statement:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and
receiver.
— Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for
help.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
FCC Caution
Changes or modications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
ICES Statement
CAN ICES-3 (B)/NMB-3 (B)
ONE-YEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
For customer service, call 877-467-4289 (U.S.) or
01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated
companies.
Registered in some countries.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2014 Best Buy. All rights reserved.
Made in China
V1 ENGLISH 14-0351
Loading...