Insignia NS-WLM1451-SV, NS-WLM1451-SV-C Quick Setup Manual
Quick Setup Guide | NS-WLM1451-SV/NS-WLM1451-SV-C
Five-Button Wireless Mouse
PACKAGE CONTENTS
• Five-button wireless mouse
• Nano receiver
• Quick Setup Guide
SYSTEM REQUIREMENTS
• Windows® 8, Windows® 7, Windows Vista®, Windows® XP, or Mac OS 10.4
or higher
• One available USB port
Features
To p
Bottom
Scroll wheel
Right
button
Left button
Nano receiver
LED indicator
Backward
Forward
ON/OFF switch
Connect
button
INSTALLING THE BATTERIES
1 Take the battery cover o.
2 Insert the battery inside the battery compartment.
Note: Insert the battery with the correct orientation, according to the instruction
label on the mouse.
3 Replace the cover.
and
Pull
AA battery
REMOVING THE NANO RECEIVER
1 Remove the battery cover.
2 Pull the nano receiver out of its slot in the battery compartment.
3 Replace the cover.
Before using your new product, please read these instructions to prevent any damage.
Battery cover
SETTING UP THE CONNECTION BETWEEN THE
RECEIVER AND THE MOUSE
1 Plug the nano receiver into a USB port on your computer.
Note: The drivers automatically install onto your computer and you can start using
your mouse immediately.
2 If the mouse does not work, put it into pairing mode by pressing the
connect button on the bottom of your mouse.
Note: If the mouse does not work after 10 seconds, unplug and re-plug the nano
receiver then press the connect button on the mouse again.
3 The LED indicator on the mouse ashes steadily when it is in pairing mode
and turns o when it is successfully paired with the nano receiver.
4 If the battery power gets low, the battery indicator on the mouse will blink
continuously for 10 seconds.
REMOVING THE NANO RECEIVER FROM YOUR COM
PUTER
Windows:
1 To remove the nano receiver from your PC, right-click the USB device icon
in your system tray, located on the right side of your task bar.
2 Click Eject 2.4G Wireless Mouse. A message appears that you are now
“Safe to Remove Hardware.”
3 Remove the receiver from your computer.
Mac OS:
1 Click the Finder icon on your dock. The Finder window opens.
2 In the left panel, select 2.4G Wireless Mouse under the “DEVICES”
heading, then click (eject). “2.4G Wireless Mouse” disappears and the
USB device can be safely removed from your computer.
MOUSE INDICATOR
LED indicator
Power ON LED is on for 3 sec.
Low battery warning LED blinks for 10 sec.
Pairing LED blinks 3 times.
When paired or LED is o.
failed after 10 sec.
SPECIFICATIONS
Rating: 1.5V D.C. - 10mA
CLEANING YOUR MOUSE
• Wipe the mouse with a damp, lint-free cloth.
TROUBLESHOOTING
• Make sure that your computer meets the system requirements.
• Only use the mouse on a clean, at, non-slippery surface to ensure
smooth and accurate cursor action.
• If your mouse stops working:
• Make sure that your mouse and nano receiver are paired by pressing
the connect button on the mouse.
• Replace the mouse battery.
• Avoid using your mouse on reective, transparent, or metallic surfaces.
LEGAL NOTICES
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warn ing : Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
RSS-Gen and RSS-210 statement
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
RSS-102 statement
This equipment complies with Industry Canada radiation exposure limits set forth for an
uncontrolled environment.
Cet équipement est conforme à l'exposition aux rayonnements Industry Canada limites établies
pour un environnement non contrôlé.
ONEYEAR LIMITED WARRANTY
For complete warranty, visit www.insigniaproducts.com.
CONTACT INSIGNIA
For customer service, call 1-877-467-4289 (U.S. and Canada)
or 01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated companies.
Registered in some countries.
Distributed by Best Buy Purchasing, LLC, 7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2014 Best Buy. All rights reserved.
Made in China
V4 ENGLISH 14-0702
Loading...