Page 1
USER GUIDE
Espresso Finish Closed Cabinet
TV Stand
for TVs up to 50”/95 lbs
NS-WD1450/NS-WD1450-C
SAFETY INFORMATION AND SPECIFICATIONS....2
PACKAGE CONTENTS: PARTS.....................................3
PACKAGE CONTENTS: HARDWARE..........................4
ASSEMBLY INSTRUCTIONS.........................................5
CARE AND MAINTENANCE...................................... 19
Before using your new product, please read these instructions to prevent any damage.
Page 2
ESPRESSO FINISH CLOSED CABINET TV STAND
Maximum overall weight: 200 lbs. (90.7 kg)
Maximum top shelf weight: 95 lbs. (43 kg)
Maximum adj. center shelf weight: 25 lbs.
Maximum adj. side shelf weight: 20 lbs.
Maximum bottom shelf weight: 60 lbs.
Maximum screen size: 50” diagonal
Overall dimensions (H × W × D):
25.5 × 47.25 × 19 in. (64.8 x 120 x 48.3 cm)
47.3 inch
(120 cm)
25.5 inch
(64.8 cm)
19 inch
(48.3 cm)
95 lbs.
25 lbs.
25 lbs.
60 lbs.
2
0
l
b
s
.
2
0
l
b
s
.
Phillips screwdriver
Hammer
SAFETY INFORMATION AND SPECIFICATIONS
CAUTION: The top surface of this stand
is designed for use with a product
weighing no more than
95 lbs. (43 kg) and having a width that
with no more than a one-inch overhang on each
side of the shelf. Use with products that weigh more
than the maximum weight allowed, or with
dimensions that extend beyond the maximum
width may result in instability, which may result in
injury.
Model #: NS-WD1450
permits it to sit evenly on the stand
CAUTION: This product contains small
items that could be a choking hazard if
swallowed.
Keep these items away from young
children!
Tools needed:
2
www.insigniaproducts.com
Page 3
ESPRESSO FINISH CLOSED CABINET TV STAND
A
B
C
D
E
F
G
H
I
J
K
L
M
O
P
Q
R
T
H
I
J
K
M
P
R
S
T
PACKAGE CONTENTS: PARTS
Make sure that you have all the parts necessary to assemble your new TV stand. While not all parts are
labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts
from each other. Use this part identification to help identify similar parts.
A Right End 1 K Small Adjustable Shelf 2
BLeft End 1 LLong Skirt 1
C Right Upright 1 M Short Skirt 2
D Left Upright 1 O Top Molding 1
ETop 1 PLong Brace 2
FBottom 1 QShort Brace 1
GBack 1 RSide Brace 2
H Outer Back 2 S Inner Base Block 2
I Door 2 T Outer Base Block 2
J Large Adjustable Shelf 2
www.insigniaproducts.com
3
Page 4
ESPRESSO FINISH CLOSED CABINET TV STAND
Label Hardware Qty.
U8
V2
W2
X1
Y18
Z4
AA 2
BB 4
Sauder
twist-lock®
fasteners
Hidden cam
Cam dowel
Large metal
bracket
Metal bracket
Hinge
Knob
Felt discs
Label Hardware Qty.
CC 24
DD 16
EE 1
FF 10
GG 14
HH 2
II 37
JJ 8
KK 20
Metal pin
Rubber sleeve
Warning label
Black 1-7/8” flat head screw
Silver 1-1/8” flat head screw
Gold 1” machine screw
Black 9/16” large head screw
Black 1/2” flat head screw
Nail
PACKAGE CONTENTS: HARDWARE
Note: The table below shows the required hardware. You may receive extra hardware.
Make sure that you have all the hardware necessary to assemble your new TV stand.
1234in
10 20 30 40 50 60 70 80 90 100mm
4
www.insigniaproducts.com
Page 5
ESPRESSO FINISH CLOSED CABINET TV STAND
U (8)
ASSEMBLY INSTRUCTIONS
Step 1: Preparing the right and left ends and the uprights
Caution: Assemble your stand on a carpeted floor or on the empty carton to avoid scratching your stand.
• Push a Sauder twist-lock
and D).
NOTE: Do not tighten the Sauder twist-lock® fasteners at this time.
®
fastener (U) into the large holes in the right and left ends (A and B) and uprights (C
U
A
B
You’ll need:
D
C
www.insigniaproducts.com
5
Page 6
ESPRESSO FINISH CLOSED CABINET TV STAND
V
W
Q
Arrow
Arrow
Insert the cam dowel into the hidden cam.
V (2)
W (2)
Step 2: Preparing the short brace
• Push two hidden cams (V) into the short brace (Q). Then, insert the metal end of a cam dowel (W) into
each hidden cam (V).
NOTE: Do not tighten the hidden cams in this step.
You’ll need:
6
www.insigniaproducts.com
Page 7
ESPRESSO FINISH CLOSED CABINET TV STAND
E
O
Curved edge
Finished surface
S
u
r
f
a
c
e
w
i
t
h
h
o
l
e
s
Phillips screwdriver
GG (6)
Step 3: Preparing the top
• Fasten the top molding (O) to the top (E). Use six silver 1-1/8” flat head screws (GG).
You’ll need:
www.insigniaproducts.com
7
Page 8
ESPRESSO FINISH CLOSED CABINET TV STAND
Finished edge
Dowel end
S
u
r
f
a
c
e
w
i
t
h
o
u
t
S
a
u
d
e
r
t
w
i
s
t
-
l
o
c
k
®
f
a
s
t
e
n
e
r
s
S
u
r
f
a
c
e
w
i
t
h
S
a
u
d
e
r
t
w
i
s
t
-
l
o
c
k
®
f
a
s
t
e
n
e
r
s
Phillips screwdriver
Step 4: Attaching the uprights to the top
•Fasten the uprights (C and D) to the underside of the top (E), then tighten the four Sauder twist-lock®
fasteners (U).
To use the Sauder twist-lock® fasteners:
1 Insert the dowel end of the fastener into the hole of the adjoining part.
Note: The dowel end of the fastener must remain fully inserted in the hole of the adjoining part while locking the fastener.
2 Tighten the fastener with a Phillips screwdriver as tight as possible.
You’ll need:
D
C
E
8
www.insigniaproducts.com
Page 9
ESPRESSO FINISH CLOSED CABINET TV STAND
F
i
n
i
s
h
e
d
F
i
n
i
s
h
e
d
CC (8)
Step 5: Attaching the outer backs
1 Insert two metal pins (CC) into each side of the outer backs (H).
2 Insert the metal pins (CC ) in the outer backs (H) into the holes in the uprights (C and D).
CC
CC
H
D
C
H
You’ll need:
www.insigniaproducts.com
9
Page 10
ESPRESSO FINISH CLOSED CABINET TV STAND
Finished edge
Finished edge
S
u
r
f
a
c
e
w
i
t
h
S
a
u
d
e
r
t
w
i
s
t
-
l
o
c
k
®
f
a
s
t
e
n
e
r
s
S
u
r
f
a
c
e
w
i
t
h
o
u
t
S
a
u
d
e
r
t
w
i
s
t
-
l
o
c
k
®
f
a
s
t
e
n
e
r
s
Phillips screwdriver
Step 6: Attaching the ends
• Fasten the ends (A and B) to the top (E), then tighten the four Sauder twist-lock® fasteners (U).
Note: Make sure that the metal pins (CC) in the outer backs (H) insert into the holes in the ends (A and B).
H
B
H
E
A
10
You’ll need:
www.insigniaproducts.com
Page 11
ESPRESSO FINISH CLOSED CABINET TV STAND
FF
B
D
C
A
F
Q
FF
Surface with
hidden cams
U
n
f
i
n
i
s
h
e
d
s
u
r
f
a
c
e
Curved edge
CAUTION
Risk of damage or
injury. Hidden cams
must be completely
tightened. Hidden
cams that are not
completely tigh tened
may loosen and parts
may separate.
START
TIGHTEN
Arrow
Arrow
Maximum
210 degrees
Minimum
190 degrees
Phillips screwdriver
FF (8)
Step 7: Attaching the bottom and the short brace
1 Fasten the bottom (F) to the ends (A and B) and the uprights (C and D) with eight black 1-7/8” flat head
screws (FF).
2 Fasten the short brace (Q) to the bottom (F), then tighten the two hidden cams (V).
CAUTION: Risk of damage or injury. Hidden cams must be completely tightened. Hidden cams that are not
completely tightened may loosen and parts may separate.
You’ll need:
www.insigniaproducts.com
11
Page 12
ESPRESSO FINISH CLOSED CABINET TV STAND
Unfinished
surface
Unfinished
surface
Phillips screwdriver
Y (18)
II (18)
Step 8: Preparing the braces
• Fasten the eighteen metal brackets (Y) to the long braces (P) and side braces (R) with eighteen black 9/16” large
head screws (II).
Note: Make sure that the brackets are even with the edges of the braces.
Y
Y
P
P
Y
Y
Y
R
R
You’ll need:
12
www.insigniaproducts.com
Page 13
ESPRESSO FINISH CLOSED CABINET TV STAND
Surface without
metal brackets
Surface without
metal brackets
Surface without
metal brackets
Phillips screwdriver
II (18)
FF (2)
Step 9: Attaching the braces
1 Fasten the long braces (P) to the bottom (F) with eight black 9/16” large head screws (II).
2 Fasten the long braces (P) to the short brace (Q) with two black 1-7/8” flat head screws (FF).
3 Fasten the side braces (R) to the bottom (F) and long braces (P) with ten black 9/16” large head screws (II).
FF
R
P
F
Q
P
R
You’ll need:
www.insigniaproducts.com
FF
13
Page 14
ESPRESSO FINISH CLOSED CABINET TV STAND
P
F
X
T
S
S
T
M
M
L
Notch should be
located here
F
i
n
i
s
h
e
d
Notch should be
located here
F
i
n
i
s
h
e
d
F
i
n
i
s
h
e
d
Phillips screwdriver
II (18)
GG (8)
X (1)
Step 10: Attaching the base blocks and skirts
1 Fasten the base blocks (S and T) to the long brace (P) with eight silver1-1/8” flat head screws (GG).
Note: There are no pre-drilled holes in the base blocks. The screws will tighten into the grooves in the base blocks. The
outer base blocks (T ) have only one notch and the inner base blocks (S) have two notches. Pay close attention to
the positioning of the base blocks.
2 Fasten the large metal bracket (X) to the bottom (F) with a black 9/16” large head screw (II).
3 Insert the skirts (L and M) into the notches in the base blocks.
Note: Make sure that the long skirt (L) is positioned in front of the large metal bracket.
You’ll need:
14
www.insigniaproducts.com
Page 15
ESPRESSO FINISH CLOSED CABINET TV STAND
G
The perforations should
be positioned here
U
n
f
i
n
i
s
h
e
d
s
u
r
f
a
c
e
Hammer
KK (20)
Step 11: Attaching the back
1 Carefully turn over your TV stand onto its front edges. Unfold the back (G) and lay it over the unit.
2 Make sure the back is centered along all four edges. Push on opposite corners, if required, to make it square.
3 Fasten the back (G) to the unit with nails (KK).
Note: Perforations have been provided for access through the back. Carefully cut out the holes, as needed.
CAUTION: Do not stand the unit upright without the back fastened. The unit may collapse.
You’ll need:
www.insigniaproducts.com
15
Page 16
Step 12: Attaching the doors
I
Z
I
A
AA
BB
C
HH
3a
3c
Horizontal
adjustment screw
Mounting
screw
(depth)
Vertical adjustment
screw
Hinge plate
JJ (8)
HH (2)
BB (4)
Z (4)
AA (2)
Phillips screwdriver
1 Carefully stand your unit upright.
2 Fasten two hinges (Z) to each door (I). Use four black 1/2” flat head screws (JJ) on each door.
3 Fasten the first door (I) to the right end (A) and the second door (I) to the left end (B). Use the screws in the
hinges.
a. Loosen the mounting screw on both hinges, then slide the hinge apart.
b. Tighten the vertical adjusting screws on the hinge plates partway into the right end (A).
c. Slide the hinges back together by aligning the door (I) with right end (A) then tighten the vertical
adjustment screws and mounting screws.
d. Repeat steps a-c for to attach the second door (I) to the left end (B).
4 Fasten a k n ob (AA) to each door (I). Use the gold 1” machine screws (HH).
5 Stick two felt disks (BB) on each door (I) where it comes in contact with the uprights (C or D).
ESPRESSO FINISH CLOSED CABINET TV STAND
You’ll need:
16
www.insigniaproducts.com
Page 17
ESPRESSO FINISH CLOSED CABINET TV STAND
Mounting screw (depth)
Vertical adjustment screw
Horizontal
adjustment screw
Phillips screwdriver
Step 13: Adjusting the doors
Refer to the enlarged diagram to identify the parts on the hinges.
The doors may need some adjustments. Follow the text below to make needed adjustments.
DOOR ADJUSTMENTS:
• To adjust the doors from side to side (horizontal), loosen the horizontal adjustment screws several turns, then
turn the adjusting screw in or out. Tighten the mounting screw after making adjustments.
• To adjust the doors up and down (vertical), loosen both sets of vertical adjustment screws. Move the doors up or
down to the desired location. Tighten the screws after making adjustments.
• To adjust the doors in or out (depth), loosen the mounting screws one turn and move the doors in or out, as
needed. Tighten the mounting screws after making adjustments.
You’ll need:
www.insigniaproducts.com
17
Page 18
ESPRESSO FINISH CLOSED CABINET TV STAND
Never use this furniture with a TV that
is too large or too heavy. Severe injury
or death can occur. The TV and
furniture will be unstable and may tip.
- The TV must weigh less than 95 lbs.
- The base of the TV must be able to
sit completely on this shelf.
WARNING
CC (16)
DD (16)
EE (1)
Step 14: Attach miscellaneous hardware and labels
1 Push the rubber sleeves (DD) over one end of each metal pin (CC). Insert the metal end of the pins into the hole
locations of your choice in the ends (A and B) and uprights (C and D). Set the adjustable shelves (J and K) onto
the metal pins.
2 Apply the warning label (EE) to the top (E). You should be able to read the label when the TV is removed from
the unit. When the TV is in place, it should hide the label. Peel off the backing and apply the label as shown in
the diagram.
Note: This is a permanent label intended to last for the life of the product. After it is applied, do not try to remove it.
Note: Please read the back pages of this instruction booklet for important safety information.
3 This completes the assembly. Clean your TV stand with your favorite furniture polish or a damp cloth, then wipe
dry.
EE
B
You’ll need:
K
20 lbs.
E
95 lbs.
25 lbs.
25 lbs.
D
J
J
60 lbs.
C
K
20 lbs.
A
CC
DD
18
www.insigniaproducts.com
Page 19
ESPRESSO FINISH CLOSED CABINET TV STAND
CARE AND MAINTENANCE
Wood/Laminate
• Use your favorite type of furniture polish.
• Do not spray polish directly onto the stand. Spray onto a soft cloth then wipe the stand.
• Always test any polish in a discrete location first, such as the back of the stand, to make sure that there is no
adverse reaction.
• Dust frequently with a soft cloth.
• Never slide objects across surfaces. Lift objects from the top surface rather than dragging them across the finish
when moving them.
• Do not expose your stand to direct sunlight, drying heat sources, or dampness.
Glass
• Use a commercial liquid glass cleaner and a soft cloth.
• Do not use harsh powders or any other abrasive substances as they will scratch the glass.
• Clean spills immediately with a soft, damp cloth.
• Protect surfaces by using felt, leather, or cork under accessories.
• Use a protective pad when using your stand as a writing surface (especially when using a ballpoint pen).
• Dust frequently with a soft cloth.
WARNING
Please use your stand correctly and safely. Improper use can cause safety hazards or damage to your furniture or household items. Carefully read
the following chart.
Look out for: What can happen: How to avoid the problem:
• Children climbing on the stand.
• A child may try to reach a toy or other object by climbing
on the st and.
• Children will play and be active near the TV.
• Improper use of the stand to support TVs.
• The stand is designed for use with TVs will specify the
maximum weight rating and recommended size of the
TVs it will safely support.
• Overloaded shelves • Risk of injury.
• Improperly moving the stand. • The stand can tip over or break if improperly moved.
• Risk of injury or death.
• A child climbing on the stand can make it top-heavy and
cause it to tip over.
• A child playing with a TV can cause it to tip over.
• Risk of injury or death.
• TVs can be very heavy. Note, older CRT TVs tend to be
unbalanced and prone to tipping forward.
• Top-heavy furniture can tip over.
• Overloaded shelves can break.
•Risk of injury.
• Never allow children to climb on or play with the stand.
• Do not place toys or food on the top shelves. Children may
try to climb to reach them out of curiosity.
• A TV must only be set on furniture specifically designed to
support a television.
• Never use a TV that exceeds the weight ratings or size
guidelines specified for the stand.
• Never exceed the weight limits shown in the instructions.
• Work from the bottom to the top when loading shelves.
• The bottom shelves can only support 25 lbs. while the top
can support 95 lbs.
• Unload shelves from the top to the bottom before moving
the stand.
• Do not push the stand, especially on a carpeted floor. Have a
friend help you lift the item and set it in place.
• Do not lift the s tand using the top shelf. Lift from the frame
or leg assembly.
• Remove the TV before moving the TV stand.
www.insigniaproducts.com
19
Page 20
ESPRESSO FINISH CLOSED CABINET TV STAND
ONE-YEAR LIMITED WARRANTY - INSIGNIA
Definitions:
The Distributor* of Insignia branded products warrants to you,
the original purchaser of this new Insignia-branded product
(“Product”), that the Product shall be free of defects in the
original manufacturer of the material or workmanship for a
period of one (1) year from the date of your purchase of the
Product (“Warranty Period”).
For this warranty to apply, your Product must be purchased in
the United States or Canada from a Best Buy branded or Future
Shop branded retail store or online at www.bestbuy.com,
www.bestbuy.ca, or www.futureshop.ca and is packaged with
this warranty statement.
How long does the coverage last?
The Warranty Period lasts for 1 year (365 days) from the date you
purchased the Product. Your purchase date is printed on the
receipt you received with the Product.
What does this warranty cover?
During the Warranty Period, if the original manufacture of the
material or workmanship of the Product is determined to be
defective by an authorized Insignia repair center or store
personnel, Insignia will (at its sole option): (1) repair the Product
with new or rebuilt parts; or (2) replace the Product at no charge
with new or rebuilt comparable products or parts. Products and
parts replaced under this warranty become the property of
Insignia and are not returned to you. If service of Products or
parts are required after the Warranty Period expires, you must
pay all labor and parts charges. This warranty lasts as long as you
own your Insignia Product during the Warranty Period. Warranty
coverage terminates if you sell or otherwise transfer the Product.
How to obtain warranty service?
If you purchased the Product at a Best Buy or Future Shop retail
store location, please take your original receipt and the Product
to any Best Buy or Future Shop store. Make sure that you place
the Product in its original packaging or packaging that provides
the same amount of protection as the original packaging. If you
purchased the Product from a Best Buy or Future Shop online
web site (www.bestbuy.com, www.bestbuy.ca, or
www.futureshop.ca), mail your original receipt and the Product
to the address listed on the web site. Make sure that you put the
Product in its original packaging or packaging that provides the
same amount of protection as the original packaging.
To obtain warranty service, in the United States call
1-888-BESTBUY, Canada call 1-866-BESTBUY for Future Shop call
1-800-663-2275. Call agents may diagnose and correct the issue
over the phone.
• Modification of any part of the Product, including the
antenna
• Display panel damaged by static (non-moving) images
applied for lengthy periods (burn-in).
• Damage due to incorrect operation or maintenance
• Connection to an incorrect voltage or power supply
• Attempted repair by any person not authorized by Insignia
to service the Product
• Products sold “as is” or “with all faults”
• Consumables, including but not limited to batteries (i.e. AA,
AAA, C etc.)
• Products where the factory applied serial number has been
altered or removed
• Loss or Theft of this product or any part of the product
• Display panels containing up to three (3) pixel failures (dots
that are dark or incorrectly illuminated) grouped in an area
smaller than one tenth (1/10) of the display size or up to
five (5) pixel failures throughout the display. (Pixel based
displays may contain a limited number of pixels that may
not function normally.)
• Failures or Damage caused by any contact including but
not limited to liquids, gels or pastes.
REPAIR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS
YOUR EXCLUSIVE REMEDY FOR BREACH OF WARRANTY. INSIGNIA
SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR THE BREACH OF ANY EXPRESS
OR IMPLIED WARRANTY ON THIS PRODUCT, INCLUDING, BUT
NOT LIMITED TO, LOST DATA, LOSS OF USE OF YOUR PRODUCT,
LOST BUSINESS OR LOST PROFITS. INSIGNIA PRODUCTS MAKES
NO OTHER EXPRESS WARRANTIES WITH RESPECT TO THE
PRODUCT, ALL EXPRESS AND IMPLIED WARRANTIES FOR THE
PRODUCT, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTIES OF AND CONDITIONS OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN
DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE AND
NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY
AFTER THE WARRANTY PERIOD. SOME STATES, PROVINCES AND
JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT
APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY
FROM STATE TO STATE OR PROVINCE TO PROVINCE.
Contact Insignia:
For customer service please call 1-877-467-4289
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its affiliated companies.
Registered in some countries.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richfield, MN 55423 U.S.A.
©2014 Best Buy. All rights reserved.
Made in USA with U.S. and imported materials
Where is the warranty valid?
This warranty is valid only in the United States and Canada at
Best Buy or Future Shop branded retail stores or websites to the
original purchaser of the product in the county where the
original purchase was made.
What does the warranty not cover?
This warranty does not cover:
• Customer instruction/education
•Installation
•Set up adjustments
•Cosmetic damage
• Damage due to weather, lightning, and other acts of God,
such as power surges
• Accidental damage
•Misuse
•Abuse
•Negligence
• Commercial purposes/use, including but not limited to use
in a place of business or in communal areas of a multiple
dwelling condominium or apartment complex, or
otherwise used in a place of other than a private home.
20
www.insigniaproducts.com
Page 21
Certificate of Conformity
1. This certificate applies to the Insignia Product
identified by this instruction booklet.
2. This certificate applies to the compliance of this
product with the CPSC Ban on Lead-Containing
Paint (16 CFR 1303).
3. This product was manufactured for:
Insignia
4. Date of Manufacture: _______________
Lot number: 361832
1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)
www.insigniaproduc ts.com
INSIGNIA is a trademark o f Best Buy and its affiliated companies.
Registered in some countries.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richfield, MN 55423 U.S.A.
©2014 Best Buy. All rights reserved.
Made in USA with U.S. and imported materials
V3 ENGLISH
14-0647
Loading...