Insignia NSCAHBTEB01-C, NSCAHBTEB01-B, NS-CAHBTEB01-B-C User Manual

OFF/ON

QUICK SETUP GUIDE

Bluetooth Headset

NS-CAHBTEB01 / NSCAHBTEB01-B / NSCAHBTEB01-C / NS-CAHBTEB01-B-C

PACKAGE CONTENTS

• Bluetooth Headset

• USB charging cable

• Earbuds (small and large)

• Quick Setup Guide

Before using your new product, please read these instructions to prevent any damage.

F/ON

FEATURES

• High-quality stereo sound from Bluetooth 4.0 enabled devices

• Battery lasts 12 hours (talk), 10 hours (music)

• Inline controls easily adjust audio

• Curved design ﬁts comfortably around the neck

Rewind/Skip back

Fast forward/Skip forward

Play/Pause

Charging port

Neck strap

Earbud (R) Power switch

Microphone Earbud (L) Call button/LED indicator Volume down Volume up

CHARGING YOUR HEADSET

A tone sounds (every 60 seconds) and the LED ﬂashes red when your headset battery is low.

• Set power switch to OFF before charging.

• Connect the USB charging cable from your headset’s charging port to a USB port.

F/ F

PAIRING YOUR HEADSET

Pairing your ﬁrst Bluetooth device

1 Slide the power switch to ON. The LED blinks red

and blue and the headset enters pairing mode.

2 Make sure that your Bluetooth device is within 33 ft. (10 m) of your headset. 3 Turn on your Bluetooth device, turn on Bluetooth,

then set your device to pairing mode. For more information, see the documentation that came with your Bluetooth device.

4 On your Bluetooth device, select

NS-CAHBTEB01. The LED lights blue and a tone

sounds when your headset pairs to your Bluetooth device.

Manually pairing your Bluetooth device

1 Press and hold  (call) to enter pairing mode. The

LED blinks red and blue. 2 Make sure that your Bluetooth device is within 33 ft. (10 m) of your headset. 3 Turn on your Bluetooth device, turn on Bluetooth,

then set your device to pairing mode. For more

information, see the documentation that came

with your Bluetooth device.

4 On your Bluetooth device, select

NS-CAHBTEB01. The LED lights blue and a tone

sounds when your headset pairs to your

Bluetooth device.

Pairing two devices

1 Pair your headset to your secondary Bluetooth

device ﬁrst. See “Pairing your ﬁrst Bluetooth

device” for instructions. 2 Press and hold (call) on your Bluetooth headset

to enter pairing mode. 3 Connect your primary Bluetooth device to your

Bluetooth headset. See “Manually pairing your

Bluetooth device” for instructions. 4 Re-pair your secondary Bluetooth device to your

Bluetooth headset. See “Manually pairing your

Bluetooth device” for instructions.

Note: When connected to two phones, the headset

calling functions will work with the primary phone.

Disconnecting and reconnecting your paired

device

Your headset remembers up to six Bluetooth devices and will turn oﬀ after three minutes if it is not paired to a Bluetooth device.

TO DISCONNECT...

Turn oﬀ your headset

TO RECONNECT...

Turn on your headset. Your headset searches for the last connected Bluetooth device and reconnects.

TO DISCONNECT…

Move the Bluetooth device out of range

Turn oﬀ your Bluetooth device

Turn oﬀ Bluetooth on your Bluetooth device

Connect your Bluetooth device to another Bluetooth device

TO RECONNECT…

Make sure your Bluetooth device is within 33 feet of your headset.

Turn on your Bluetooth device, then make sure Bluetooth is on.

Turn on Bluetooth on your Bluetooth device.

Disconnect your Bluetooth device from the other Bluetooth device, then set your device to pairing mode. Select “NS-CAHBTEB01” on your Bluetooth device.

Note: If a device does not automatically reconnect, you

may need to reselect “NS-CAHBTEB01” on your Bluetooth device.

WEARING YOUR HEADSET

USING YOUR HEADSET

Making phone calls

Note: When your headset is connected to two Bluetooth

devices, calling functions work with the primary Bluetooth device (the one that is connected second or made the last outgoing call).

• To make a call, use your phone’s controls, then select the headset as the audio source.

• To redial the last number on your primary phone, press  (call) twice.

• To answer an incoming call, press  (call).

Note: Your headset vibrates when there is an incoming

call.

• To switch audio between your headset and phone, use your phone’s controls.

• To reject an incoming call, press and hold  (call) for two seconds.

• To end a call, press  (call) one time.

Call waiting

• To switch to an incoming call, press  (call) twice while speaking on an active call.

• To switch between two active calls, press  (call) twice.

• To end both calls, press  (call).

Begin playback on your Bluetooth device.

• To play audio, press

.

• To skip to the next track, press .

• To skip to the previous track, press .

• To fast forward, press and hold .

• To rewind, press and hold

.

SPECIFICATIONS

• Average charging time: 1.5 - 2 hours

• Operating time: Talk - 12 hours / Music - 10 hours

• Working distance: Up to 33 ft. (10 m)

• Battery: Lithium 200mAh/3.7V

SAFETY INFORMATION/CAUTION

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Caution

Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, maybe cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more of the following measures:

TROUBLESHOOTING

PROBLEM

No sound or low volume

Cannot connect with Bluetooth

Bluetooth device keeps unpairing

“NS-CAHBTEB01” does not appear on my Bluetooth device

No Power

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit diﬀerent form that to which the receiver is connected.

• Consul the dealer or an experienced radio/TV technician for help.

Industry Canada Compliance IC Statement

This device complies with Industry Canada’s licence exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitaĕon est autorisée aux deux condiĕons suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'uĕlisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est suscepĕble d'en compromeĥre le foncĕonnement.

SOLUTION

• Make sure that your Bluetooth device is turned on, Bluetooth is turned on, and “NS-CAHBTEB01” is selected.

• Turn up the volume on your headset and Bluetooth device.

• Make sure that your Bluetooth device is not muted.

• Make sure that your headset and Bluetooth device are not paired to other devices.

• Shorten the distance between your headset and Bluetooth device.

• Turn your devices oﬀ, then on. Re-pair your headset and Bluetooth device.

• Make sure that your headset and Bluetooth device are not paired to other devices.

• Make sure that your Bluetooth device supports the HSP, SFP, A2DP, or AVRCP Bluetooth protocol.

• Make sure that you have selected “NS-CAHBTEB01” on your Bluetooth device.

• Shorten the distance between your headset and your Bluetooth device.

• Recharge your headset and Bluetooth device's batteries.

• Shorten the distance between your headset and Bluetooth device.

• Put your headset into pairing mode, then refresh your list of Bluetooth devices. For more information, see the documentation that came with your Bluetooth device.

• Make sure your Bluetooth headset is charged.

• Make sure your Bluetooth headset is turned ON.

RSS-102 Statement:

This equipment complies with Industry Canada radiaĕon exposure limits set forth for an uncontrolled environment. Cet équipement est conforme à l'exposiĕon aux rayonnements Industry Canada limites établies pour un environnement non contrôlé.

ONEYEAR LIMITED WARRANTY

Visit www.insigniaproducts.com for details.

CONTACT INSIGNIA:

1-877-467-4289 (U.S. and Canada) 01-800-926-3000 (Mexico) www.insigniaproducts.com

INSIGNIA is a trademark of Best Buy and its aﬃliated companies. Distributed by Best Buy Purchasing, LLC, 7601 Penn Ave South, Richﬁeld, MN 55423 U.S.A. ©2016 Best Buy. All rights reserved. Made in China

V6 ENGLISH 16-0564