Insignia NS-F10T7-NG, NS-FT10MT8, NS-F10T7-BK, 10 inch Series, NS-F10T7-PK Quick Setup Manual
QUICK SETUP GUIDE
10" Table Fan
NS-F10T7-PK / NS-F10T7-BK /
NS-F10T7-NG / NSFT10MT8
PACKAGE CONTENTS
• 10" table fan
• Quick Setup Guide
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE IMPORTANT INSTRUCTIONS
1 Use your fan only as described in this Quick Setup Guide.
2 Do not use your fan if it works intermittently, stops working
entirely, or parts are missing or damaged.
3 To reduce the risk of re or electrical shock, DO NOT use this fan
with any solid-state speed control devices (such as a dimmer
switch) or expose it to water.
4 To help prevent electrical shock, do not immerse your fan, plug,
or power cord in water or spray it with liquids.
5 Close supervision is needed when your fan is being used near
children.
6 Unplug your fan before moving or cleaning it, or when it is not
in use.
7 Never insert ngers or other objects through the grill while the
fan is running.
8 Make sure your fan is on a stable surface during use so it won’t
overturn.
9 Do not use your fan in an open window. Rain may cause an
electrical hazard.
10 Do not use your fan near explosive or ammable fumes.
11 Do not place your fan or its parts near an open ame, stove, or
other heating appliances.
12 Do not use your fan if the cord or plug is damaged. Throw your
fan away or return it to an authorized service facility for
examination and/or repair.
13 Do not use your fan after a malfunction, drop, or if it is is
damaged in any way.
14 To unplug, pull the plug from the power outlet. Never yank on
the power cord.
15 Always use your fan on a dry surface.
16 This fan is intended for household use only. Do not use it for
commercial or industrial use.
17 Do not use this fan near curtains, plants, window treatments, or
other loose fabrics.
18 This fan uses a fuse for overload protection. A blown fuse indicates
that an overload or short-circuit has occurred. If the fuse blows,
unplug the fan from the outlet, then replace the fuse as indicated
(using only a 5 Amp, 125 Volt fuse). If the replacement fuse blows, a
short-circuit may be present and the product should be thrown
away or returned to an authorized service facility for examination
and/or repair.
19 Do not run the power cord under carpeting, throw rugs, runners, or
other coverings. Do not route the cord under furniture or appliances. Keep the cord away from trac areas where it could be tripped
over.
Power cord
• To insert the plug, hold it rmly and guide it into the outlet.
• To unplug, hold the plug and remove it from the outlet.
• Never pull or yank on the cord or fan.
• Check the cord for cuts and abrasion marks before each use.
• Do not wrap the cord tightly around the fan. This could stress the
cord where it enters the fan and cause it to fray and break.
FEATURES
Power switch/
speed selection
Oscillation
knob
Fan blade
Grill
Adjustment knob
Before using your new product, please read these instructions to prevent any damage.
USING YOUR FAN
Speed selection
0 - O
1 - Low
2 - Medium
3 - High
Oscillation
Push the oscillation knob down to start oscillation, pull it up to stop.
Angle adjustment
1 Loosen the adjustment knob.
2 Adjust the fan to the angle you want, then retighten the knob.
SPECIFICATIONS
• Dimensions (D × W × H): 9.5 x 11.1 x 15 in. (24 x 28.2 x 38.2 cm)
• Volts: 120V, 60Hz.
• Speeds: 3 speeds
ONEYEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
For customer service, call 1-877-467-4289 (U.S. and Canada) or
01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated companies.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2016 Best Buy. All rights reserved.
Made in China
Adjustment
knob
REPLACING THE FUSE
If your fan stops working, you may need to replace the fuse (not
included).
Warning: Risk of re. Replace the fuse only with a 5A, 125 Volt fuse. Do not force
the fuse into place.
1 Unplug the fan.
2 Slide open the fuse access cover
on top of the AC power plug.
3 Remove the fuse.
4 Replace the fuse, then slide the fuse access cover closed.
Caution: Do not replace the AC power plug. Discard the product if the plug is
damaged.
CLEANING YOUR FAN
• Unplug the fan.
• Clean plastic parts with mild soap and a damp cloth or sponge.
Thoroughly remove soap lm with clear water.
• Do not splash water or other liquid into the motor.
V3 ENGLISH 16-0824
Loading...