Inovonics EE1215 User Manual

EE1215 EchoStream® Single Input

A

B

C

D

E

F

G

E

H

Twist the
screwdriver to
open the
housing

Wall Tamper
Switch

Universal Transmitter with Wall Tamper

Installation Instructions - 04931C

1 Overview

The EE1215 single input universal transmitter with wall
tamper protection is designed for use with almost any
standard contact or sensor. The transmitter is fully
supervised and includes a wall tamper switch that notifies
the system when the transmitter is removed from its
mounted surface.
The EE1215 is compliant with:

• EN50131-1

• Security Grade 2

• Environmental Class II

1.1 Inovonics Contact Information

If you have any problems with this procedure, contact
Inovonics technical services:

• E-mail: [e-mail]

• Phone: [phone]

1.2 EE1215 Components

Figure 1 EE1215 components

A Housing tamper button B NO/NC selection pins
C Input terminal D Reset button
E Wall-mount screw holes F Housing screw hole
GEchoStream select

compatability selection pins

H Transmit LED

2 Installation and Startup

2.1 Install/Replace the Battery

1. If replacing the battery, remove the housing screw.

2. Insert a small screwdriver to depress the housing

release tab on the bottom of the transmitter; twist the
screwdriver to open the housing.

2.4 Register the EE1215

Transmitters must be registered with the system in order
to be monitored and supervised. When supervised, the
transmitter will send a check-in message to the receiver.
Transmitters using the 868MHz frequency range for
Europe will send a check-in message every 12 minutes;
all other transmitters will send a check-in message every
three minutes. Each transmitter has a unique factory­programmed identification number. Refer to the receiver
installation instructions for details on registering a
transmitter.

1. When prompted by the receiver to reset transmitter,
press the Reset button.

2. Test the tra nsmitter and ensure appropriate response.

2.5 Mount the EE1215

1. Route the external wiring through the wall, as shown

in Figure 3.

Figure 2 Open the EE1215 Housing

3. If replacing a battery, remove the old battery.

4. Inst all the new battery.

5. Press the Reset button to initialize the transmitter .

6. Test the transmitter and ensure appropriate response.

2.2 Select Input Type

The NO/NC selection pins select a normally open (NO) or
normally closed (NC) state for the contact circuit wired to
the input terminal.

1. Place a selection jumper on the NO/NC selection pins
to select normally open; leave the jumper off the pins
to select normally closed.

2. Press the Reset button.

2.3 Select the EchoStream Select Compatibility

To meet ETSI requirements, Inovonics has developed a
new line of EE 868MHz-only products. These new
868MHz-only products are compatible with older systems
that include EchoStream select products. If you are using
any ES products in your current system, you will need to
enable EchoStream select compatibility on this new
868MHz-only product.
To enable/disable EchoStream select compatibility:

1. To enable compatibility with ES products, place a
selection jumper on the enable EchoStream select
compatibility selection pins.

2. If no ES products are used in your system, remove the
selection jumper from the EchoStream select
compatibility selection pins.

3. Press the Reset button.

Figure 3 Mount the Transmitter to the Wall

2. Mount the transmitter to the wall using the the wall-

mount screw holes, ensuring the housing is flush
against the wall and the wall tamper switch is firmly
depressed.

3. Close the housing.

4. Secure the housing through the enclosed housing

screw hole.

«=fезозебЕлI=OMMV=J=пппKбезозебЕлKЕзг

3 Specifications

External contacts: N/O or N/C
Distance, externa l contact to transmitter: 3m (10 ft)

maximum

Power requirements: 3VDC, 60 mA
Quiescent current: >10 uA
Low battery detection: 2.4VDC
Typical battery life: 3-5 years
Battery type (BAT604): Panasonic CR123A or

equivalent

Tamper: Type B, fixed/mounted
Operating environment: -10 to 60°C (14 to 140°F), up

to %90 relative humidity noncondensing

Dimensions: 10.5 x 4.5 x 2.3 cm (4.1 x 1.8 x 0.9")
Weight: 86g (3.0 ounces)
RF frequency range: 868-869 MHz
Compliance: EN50131-1; Security Grade 2;

Environmental class II

Certification: Telefication B.V.
Note: Specifications and data are subject to change

without notice.

4 Warranty and Disclaimer

Inovonics Wireless Corporation ("Inovonics") warrants its
products ("Product" or "Products") to conform to its own
specifications and to be free of defects in materials and
workmanship under normal use for a period of thirty-six
(36) months from the date of manufacture. Within the
warranty period, Inovonics will repair or replace, at its
option, all or any part of the warranted Product. Inovonics
will not be responsible for dismantling and/or
reinstallation charges. To exercise the warranty, the User
("User", "Installer" or "Consumer") must work directly
through their authorized distributor who will be given a
Return Material Authorization ("RMA") Number by
Inovonics. Details of shipment will be arranged directly
through the authorized distributor.
This warranty is void in cases of improper installation,
misuse, failure to follow installation and operating
instructions, alteration, accident or tampering, and repair
by anyone other than Inovonics.
This warranty is exclusive and expressly in lieu of all
other warranties, obligations or liabilities, whether written,
oral, express, or implied. There is no warranty by
Inovonics that Inovonics product will be merchantable or
fit for any particular purpose, nor is there any other
warranty, expressed or implied, except as such is
expressly set forth herein. In no event shall Inovonics be
liable for an incidental, consequential, indirect, special, or
exemplary damages, including but not limited to loss of
profit, revenue or contract, loss of use, cost of down time,
or interruption of business, nor any claim made by
distributor's customers or any other person or entity.
This warranty will not be modified or extended. Inovonics
does not authorize any person to act on its behalf to
modify or extend this warranty. This warranty will apply

only to Inovonics Products. Inovonics will not be liable for
any direct, incidental or consequential damage or loss
whatsoever, caused by the malfunction of Product due to
products, accessories, or attachments of other
manufacturers, including batteries, used in conjunction
with Inovonics Product.