INOR ICON GB User Manual

USER INSTRUCTIONS

Transmitter Conguration Kit

USB Connection

The user instruction must be read prior to adjustment and/or installation.

All information subject to change without notice.

GE N E RAL INF O RMA T ION

ICON Conguration Kit includes all necessary software and hardware for con­guration of all PC-programmable transmitters in the INOR product line from
a PC´s USB port, except for the Meso transmitters.

Conguration starts from the main program ConSoft.
ConSoft will identify the connected transmitter and open the necassary con­guration software.

ICON Conguration Kit consists of:

• USB Interface

• USB cable (connection between PC and USB Interface)

• Adapter cables (connection between USB Interface and transmitter)

• Software and drivers on a USB memory stick

Only one transmitter may be connected at a time.

The USB Interface is CE-marked and complies with the EMC-directive
2004/108/EC. For more information see the Declaration of Conformity.

ICON Conguration Kit is compatible with Windows 2000 (SP3), Windows XP
(SP2+), Windows Vista and Windows 7.

!

When installing, do not connect the USB Interface to your USB port
until prompted.

!

INOR USB Interface is a non Ex-approved product but is intended to
be used for all type of transmitters when in safe areas.

MEASURE OF SUCCESS

www.inor.com, www.inor.se

INOR Process AB, PO Box 9125, SE-200 39 Malmö, Sweden,

Phone: [phone], Fax: [phone], E-mail: [e-mail]

INOR Transmitter OY, Unikkotie 13, FI-01300 Vantaa, Finland,

Phone: [phone], Fax: [phone], E-mail: support.@inor.se

INOR Transmitter GmbH, Am Bocksborn 5, D-63571 Gelnhausen, Germany,

Phone: [phone], Fax:[phone], E-mail: [e-mail]

KROHNE Temperature Division INOR, 7 Dearborn Road, Peabody, MA 01960, USA

Phone: [phone], Fax:[phone], E-mail: [e-mail]

DATA (shortform)

Input (PC to USB Interface) USB cable
Output (USB Interface to Changeable adapter cables
transmitter)
Power Supply PC´s USB port, 5 VDC, 74 mA max
Ambient temperature

Operation 0 to 50 °C / 32 to 122 °F
Storage -20 to 70 °C / -4 to 140 °F

Humidity (non-condensing) 0 to 90 %RH
Galvanic isolation 1500 VAC
USB compliance USB v1.1 and USB v2.0
System requirements

Windows Windows 2000 (SP3), XP (SP2+),
Vista or 7.
Display resolution Minimum 800x600
Free hard disk space 50 MB
Ports 1 free USB port

INSTALLATION

INSTALLATION OF USB INTERFACE DRIVERS

Before you can use the USB Interface you must install USB drivers on your PC.
The memory stick contains the necessary USB drivers for the USB Interface.
Please refer to the guide “Installation Guide for ICON” (86BCONF004) for

installation instructions.

This product should not be mixed with other kind of scrap, after usage.

It should be handled as an electronic/electric device.

MEASURE OF SUCCESS

INSTALLATION OF CONFIGURATION SOFTWARE

All necessary software for conguration are included on the memory stick.
Please refer to the guide “Installation Guide for ICON” (86BCONF004) for
installation instructions.

86BCONF006 2010-11

All software, USB drivers and installation guides can also be downloaded from
the website www.inor.com

1.

2.

4. 5. 6.

3.

DESCRIPTION USB INTERFACE

The USB Interface is powered from the PC´s USB port.
There are three LED indicators on the USB Interface: “USB”, “PC” and “DEV”.
They are indicators to make the understanding of the communication between
PC and transmitter easier. Their functions are described below:

• “USB” LED indicates data transfer. It lights during data transfer, other­ wise it is off.

• “PC” LED indicates connection between Conguration program and PC.
When conguration is made from IPRO, MinIPAQ Soft or ProSoft, it is
green when the conguration program is open. With all other congura-
tion programs it is green only during reading or writing to transmitter.

• “DEV” LED indicates the transmitter connection status.
If it’s green, the connected transmitter is detected by the USB Inter­ face. Flashing green indicates that the USB Interface is waiting for a
new transmitter from the same product family, e.g. changing to a new
device. When it´s red no transmitter is detected by the USB Interface
and any sort of transmitter can be connected to the USB Interface.

USB INTERFACE DI M E NS I O NS

36/1.42

mm/inches

114/4.49

CONTENTS

1. USB communication cable (connection between PC and USB Interface).

2. USB Interface

3. Mini USB to Mini USB adapter (USB Interface to Transmitter)

4. Mini USB to four pole rectangular connector (USB Interface to
transmitter)

5. Mini USB to 3,5 mm tele plug connector (USB Interface to transmitter)

6. Mini USB to three pole rectangular connector (USB Interface to
transmitter)

26/1.02

LI M I TE D WA R R ANT Y

INOR Process AB, or any other afliated company within the Inor Group (hereinafter
jointly referred to as ”Inor”), hereby warrants that the Product will be free from defects
in materials or workmanship for a period of ve (5) years from the date of delivery
(”Limited Warranty”). This Limited Warranty is limited to repair or replacement at
Inor’s option and is effective only for the rst end-user of the Product. Upon receipt
of a warranty claim, Inor shall respond within a reasonable time period as to its
decision concerning:
1 Whether Inor acknowledges its responsibility for any asserted defect in
materials or workmanship; and, if so,
2 the appropriate cause of action to be taken (i.e. whether a defective
product should be replaced or repaired by Inor).
This Limited Warranty applies only if the Product:
1 is installed according to the instructions furnished by Inor;
2 is connected to a proper power supply;
3 is not misused or abused; and
4 there is no evidence of tampering, mishandling, neglect, accidenta damage,
modication or repair without the approval of Inor or damage done to
the Product by anyone other than Inor.

This Limited Warranty is provided by Inor and contains the only express war­ranty provided.

INOR SPECIFICALLY DISCLAIMS ANY EXPRESS WARRANTY NOT
PROVIDED HEREIN AND ANY IMPLIED WARRANTY, GUARANTEE
OR REPRESENTATION AS TO SUITABILITY FOR ANY PARTICULAR
PURPOSE, PERFORMANCE, QUALITY AND ABSENCE OF ANY HIDDEN
DEFECTS, AND ANY REMEDY FOR BREACH OF CONTRACT, WHICH BUT
FOR THIS PROVISION, MIGHT ARISE BY IMPLICATION, OPERATION
OF LAW, CUSTOM OF TRADE OR COURSE OF DEALING, INCLUDING
IMPLIED WARRANTIES OF MER-CHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE. EXCEPT AS PROVIDED HEREIN,
INOR FURTHER DISCLAIMS ANY RESPONSIBILITY FOR LOSSES,
EXPENSES, INCONVENIENCES, SPECIAL, DIRECT, SECONDARY OR
CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE
OF THE PRODUCT.

Products that are covered by the Limited Warranty will either be repaired or replaced
at the option of Inor. Customer pays freight to Inor, and Inor will pay the return
freight by post or other “normal” way of transport. If any other type of return freight
is requested, customer pays the whole return cost.

TRANSMITTER COMMUNICATION

The following transmitters have to be connected to a

!

power supply before communication: IPAQ-H, IPAQ-L,
IPAQ-4L, ProfIPAQ-H and ProfIPAQ-L

1. After installing the drivers for the USB interface and conguration soft­ ware, connect the USB cable and the USB interface to a free USB port
of your PC.

2. Connect the transmitter to the USB interface with a suitable Mini USB
cable.

3. Start up the ConSoft program.

4. Click on the upper left “Read from transmitter” button. ConSoft will
connect to the transmitter and open a relevant window for transmitter
conguration.

5. A new transmitter can at any time be connected, without restarting
ConSoft, by clicking on “Read from transmitter”.

CONFIGURATION

For transmitter conguration using the ICON Conguration Kit, see User
instructions for the specic transmitter.

OR D E RI N G IN F ORM A TIO N

Item Part No.
ICON Conguration Kit

70CFGUS001