R
e
g
y
n
S
Installation Guide for ICON
for Windows XP, Windows Vista and Windows 7
INO
USB Interface is a non-Ex-approved product but is
intended to be used for all type of transmitters when in
safe areas.
Do not connect the USB Interfac
to your USB
port until prompted.
SUCCESS
If you are updatin
our Co
oft software, make sure
your USB Interface has firmware 1.2.00 or higher.
Version control:
•
Connect the USB Interface to a PC
•
Start ConSoft
•
Click “About” or “Help” – “About”
The installation guide must be read prior to installation.
86BCONF004 2010-04B
MEASURE OF SUCCESS
Installation guide for ICON Table of contents
Table of contents.
1. Open INOR Setup Menu (XP) ......................................................................... 3
2. Open INOR Setup Menu (Vista)...................................................................... 4
3. Open INOR Setup Menu (Windows 7) ............................................................ 7
4. Installing drivers for the USB Interface............................................... ....... 10
5. Installing configuration software ConSoft .................................................. 12
6. Installing external configuration softwares ............................................... 16
7. Troubleshooting .......................................................................................... 17
2
Installation guide for ICON Open INOR Setup menu (XP)
1. Open INOR Setup Menu
Windows XP
1.1. For software and drivers located on a USB memory stick
1.1.1. Insert the USB memory stick into a USB port.
The first time the memory stick is connected to your PC it will be
automatically installed. A message will pop up down in the right corner
of the screen during installation, just wait.
1.1.2. Wait a few seconds, the computer will display a menu of actions to perform
as shown in figure 1.1.2.
1.1.3. Select “Start INOR setup”. Click on [OK]. The INOR Setup Menu will start as
shown in figure 1.1.3.
Figure 1.1.2 Figure 1.1.3
1.2. For software and drivers downloaded from www.inor.com
1.2.1. When you are downloading the files from internet you may get the options to
[Run] or [Save]. By choosing [Run], the setup process starts once the setup
file is downloaded.
If you selected [Save], double click on the downloaded file.
Depending on your Windows security settings you may see a Security Warning
box, if so, click on [Run].
1.2.2. The files will begin to extract. After extracting the files the INOR Setup
Menu will start as shown in figure 1.1.3.
3
Installation guide for ICON Open INOR Setup menu (Vista)
2. Open INOR Setup Menu
Windows Vista
2.1. For software and drivers located on a USB memory stick
2.1.1. Insert the USB memory stick into a USB port.
The first time the memory stick is connected to your PC it will be
automatically installed. A message will pop up down in the right corner of the
screen during installation, just wait.
2.1.1.1. If the Do you want to scan and fix Removable Disk? message
is displayed, choose “Scan and fix (recommended)”. Then click [Start].
After scanning, remove the USB memory and connect it again.
2.1.2. The computer will display a menu of actions to perform.
Click on “Start INOR setup”.
4
Installation guide for ICON and ConSoft Open INOR Setup menu (Vista)
2.1.3. Depending on your Windows security settings a User Account Control dialog
box may be displayed. Click on “Allow”.
2.1.4. The INOR Setup Menu is displayed.
2.2. For software and drivers downloaded from www.inor.com
2.2.1. When you are downloading the files from internet you may get the options to
[Run] or [Save]. By choosing [Run], the setup process starts once the setup
file is downloaded.
If you selected [Save], double click on the downloaded file.
Depending on your Windows security settings a User Account Control dialog
box may be displayed. Click on “Allow”.
5
Installation guide for ICON and ConSoft Open INOR Setup menu (Vista)
2.2.2. The files will begin to extract.
After extracting the files the INOR Setup Menu will start as shown.
6
Loading...