1
WWW.INOKIM.COM
USER GUIDE MANUAL
Check out the OX SUSPENSION ADAPTERS PATENT inside!
4
Congratulations On Your New INOKIM OXO!
We are happy you chose to ride INOKIM.
We hope you find it to be a great riding experience
adding efficiency and fun to your daily commute.
A note from the designer:
When I started designing my first electric scooter in 2009,
I envisioned a world where cars are used for long range distance
only, while lightweight personal electric devices become the
primary way of transportation in urban environments.
After ten years of sales, design and development of Quick, LIGHT
& MINI scooters, we found the need for a more powerful scooter.
Our aim was to provide a good solution for heavier riders, longer
ranges and climbs in both urban & off road surroundings.
We created OXO to be a substitute for cars in distances up to
40-50km.
Enjoy, ride carefully and return home safely.
Nimrod Sapir Riccardo
5 6
SPECIFICATIONS ............................................................................. 6
UN-BOX YOUR OXO! ...................................................................... 8
BATTERY .......................................................................................... 10
THROTTLE OPERATION ................................................................... 12
DISPLAY MODE SETTINGS ............................................................... 14
THE OXO SUSPENSION ADAPTERS PATENT ................................... 16
CAREFUL RIDING ............................................................................ 18
FOLDING MECHANISM ADJUSTMENT .......................................... 20
SERIAL NUMBER .............................................................................. 21
Table of Contents:
Myway ningbo intelligent technology will not be held
responsible for any special, consequential or incidental
damages caused by the use or misuse of our products.
The user agrees to accept full responsibility for all such risks
and to not hold myway ningbo, it’s distributors or retailers
responsible for any incident, injury to persons or damage
to property caused by misuse of the product
DISCLAIMER
It is prohibited to ride in poor weather conditions
Never ride in rain, snow, water, on icy roads, dirty wet
roads, poor visibility or other bad weather conditions
Always wear a helmet Most serious injuries that occur
while riding are head injuries. This can be prevented if
a helmet is worn. You must wear a helmet while riding
your OXO. The helmet must be worn according to its
instructions
Follow the local laws and regulations. Certain
countries or regions require safety devices or gear.
It is your responsibility to know the state laws and
follow them
Firmly lock the folding lever and check your brakes
before every ride
Do not do stunts, wheelies or jumps. They increase
your chances of injury and might damage your OXO
Do not carry passengers
Make your rst ride with INOKIM OXO
in a remote location, without any obstacles
WARNING
7 8
SPECIFICATIONS SPECIFICATIONS
MODEL
Lithium Battery 60V 25.6AH
Net Weight (+-0.5 kg) 33.5 kg
Range (km)
110 km
With constant speed of 15 km/H, 75 kg
load, in temperature of 25°C,
on a at road.
Charging Time (H) 13.5 hours
Motor-1 800W gearless (peak 1300W)
Motor-2 800W gearless (peak 1300W)
Max Speed According to local regulations
Brakes Front and rear hydraulic disc brakes
Tire Size
10 x 2.5 inch pneumatic tires with option to
equip 10 x 3 inch off-road pneumatic tires
Tire Air Pressure 40 psi to 50 psi
Folded Size L x W x H (cm) 122 x 59 x 54 cm
Open Size L x W x H (cm) 122 x 59 x 130 cm
Load Limit 120 kg
Road lighting Integral car LED lights
Throttle LCD display with functions and illumination
Recommended air pressure in tires: 40 psi to 50 psi.
122 cm | 48 inch 122 cm | 48 inch
130 cm | 51 inch
59 cm | 23 inch
54cm | 21 inch
59 cm | 23inch
LITHIUM ION BATTERY
CASTED ALUMINIUM ALLOY
ANTI SKID SURFACE
INTEGRAL REAR LIGHT
REAR HYDRAULIC
DISC BRAKE
REAR 800W BRUSHLESS
GEARLESS MOTOR
KICKSTAND
REAR SINGLE SIDED SUSPENSION
FRONT TENSION
ADJUSTER
RUBBER BAND
RED LOCKING LEVER
FOLDING MECHANISM
GRIPS
SPEED CONTROL THROTTLE
LCD DISPLAY WITH FUNCTIONS AND ILLUMINATION
FRONT 800W
BRUSHLESS
GEARLESS MOTOR
10 INCH PNEUMATIC TIRES
FRONT HYDRAULIC
DISC BRAKE
REAR MUDGUARD
FRONT LED LIGHTS
BELL
FRONT SINGLE SIDED SUSPENSION
FRONT & REAR HYDRAULIC
BRAKES LEVERS
ON/OFF FRONT MOTOR BUTTON
9 10
UN-BOX YOUR OXO!
UN-BOX YOUR OXO!
While folded, stand the OXO on kickstand.
Push down rear end of OXO to release the SNAP LOCK and raise up the
steering rod
Set the handle bar in place
Use the hex key (4m)
Are you ready to set your OXO free?
Please follow these instructions:
Fasten the RED lever
Adjust the brakes angle
according to your height.
A good indication for your suited
angle is that your wrists are
straight when you ride
4m
Connect the rear mudguard
Use hex key (5m)
When folding repeat steps
2, 3 and 4 in reverse order
and then simply snap the
steering rod into place
If the SNAP LOCK of your OXO
is too loose / tight, you can
ne-tune it by adjusting the
height of the locking hook.
Use hex key (2.5m)
1
2
7
5
3
4
8
6
9
5m
Adjust the tightening of the lever
by the front tension adjuster
Fix safety lock rubber band
3
2
4
11 12
Your OXO has a Lithium Battery with an external charger
When charging, connect the charging cable in this order:
FIRST to INOKIM’s charging socket
THEN to the electrical outlet
Charging Indication:
RED light - Battery charging
GREEN light - Charging complete
BATTERY SAFETY REGULATIONS:
Keep the battery away from children & pets
Exposure to the battery voltage can cause death or serious injury
Unplug the battery from the outlet before performing any maintenance
It is dangerous to work on an INOKIM Scooter plugged into an electrical
outlet. An electric shock can cause serious injury and damage the
scooter
Do NOT use the scooter if the battery:
• Is damaged
• Emits an unusual odour or excessive heat
• Presents any leakage
Do not operate the scooter while charging!
Charge the battery only using INOKIM’s OXO approved charger
The use, storage or charging of the INOKIM battery outside specied
limits may result in the annulment of the warranty, battery damage, and
an ineffective battery charge
DO NOT CUT, OPEN, CRUSH OR PUNCTURE BATTERIES!
IN THE EVENT OF A BATTERY LEAK, PREVENT CONTACT OF LIQUID
WITH SKIN OR EYES. IF THIS HAPPENS, WASH THE AFFECTED AREAS
IMMEDIATELY WITH WATER AND SEEK MEDICAL HELP
BATTERY
BATTERY
MAXIMIZE YOUR BATTERY’S PERFORMANCE:
1. For its initial charge, FULLY charge your OXO
This conditions the battery for future life-span
2. Do NOT leave a fully charged battery connected to a charger,
since overcharging may shorten it’s lifetime
3. Avoid extreme temperatures Always try to keep the battery
between 15°c and 25°c (59°F and 77°F). Extreme temperatures
reduce the capacity and lifetime of the battery. A device with a
hot or cold battery may not work temporarily
4. At least once a month fully charge the battery
5. From time to time discharge the battery by riding.
Use all stored energy in the battery
6. Before storing it for a long period charge the battery half way
13 14
LCD DISPLAY
THROTTLE BUTTONS INTRODUCTION
THROTTLE OPERATION
ON/OFF button
Button
Button
ACCELERATE thumb lever
THROTTLE OPERATION
POWER ON
POWER OFF
AUTO OFF
ACCELERATION
LIGHTS FUNCTION
To power on the scooter:
press
Wait until LCD display stops flashing
before you start riding
To shut down the system:
press
for three seconds
After 10 minutes of not using any function,
the scooter will automatically shut down
To accelerate: gently press the thumb lever.
The OXO is powerful so be careful!
This function is to limit the full speed of the scooter
for beginners or for more accurate riding in a
crowded surrounding.
The mode can be changed with the buttons
Your TRIP distance since your last trip reset.
Reset TRIP by long press
To swap to ODO and battery voltage: press
Your scooters total distance since its factory assembly
Your current battery voltage status
To turn the front and rear lights on: long press
The LCD back-light indicates that the lights are on.
The lights will turn on automatically if the ambient
photographic coefcient is lower than the set value
(You can set it in mode 5, p.15)
Your system has encountered an error,
please contact your local dealer to nd out what it is
WAIT UNTIL LCD DISPLAY STOPS FLASHING
BEFORE YOU START RIDING
15 16
DISPLAY MODE SETTINGS
Navigate easily through the settings:
Enter settings (mode1): Press together for 2 seconds.
Switch between modes: Press
Return to main function menu: Long press
DISPLAY MODE SETTINGS
Please be aware that when using Cruise Control,
RELEASING YOUR THUMB FROM THE THROTTLE
WILL NOT SLOW YOU DOWN!!!
You may nd yourself in danger or endangering others
2 ways to exit Cruise Control:
• Brake with the LEFT or RIGHT brake lever (both work)
• Press the thumb lever again.
If you choose to set your Cruise Control to ON. It’s very important you
practice your exit so that is comes naturally!
KM / MILE
Mode 4
PHOTOCELL
Mode 5
Default Setting: km/h (“0” indicates km).
Press or to alternate to mile (“1” indicates mile)
Long press to save setting.
Short press to enter Mode 5
The throttle has light sensors that detect the photographic
coefcient (light level) and switch your lights on/off accordingly.
Default Setting: Photocell On (“Y” indicates yes)
To disable photocell Press or (“n” indicates no)
To adjust the light level - When letter is “Y” press
Default value: 510
Press or to turn up/down the value.
Long press to save setting
LCD BACK-LIGHT
Mode 1
SPEED LIMIT MODE
Mode 2
CRUISE CONTROL
Mode 3
There are 3 levels for LCD brightness: low/medium/high.
To change level from 1 to 3: Press
Long press to save setting.
Short press to enter Mode 2
Default and highest speed: 25km/h at full throttle.
You can dene other speed limits (from 6km/h to 25km/h).
To change speed limit number: Press or
Long press to save setting.
Short press to enter Mode 3
While riding at any same speed for more than ten (10)
seconds, the Cruise Control will be turned on.
When Cruise Control is operated, you can release your
thumb from the throttle and the scooter will continue to
ride at full speed.
Default for safety reasons: Cruise Control Off
(“n” indicates no Cruise Control).
To Enable Cruise Control: Press or
(“Y” indicates yes Cruise Control).
Long press to save setting.
Short press to enter Mode 4
WARNING
17 18
THE OXO SUSPENSION ADAPTERS PATENT
LOW POSITION is the default, for better stability mainly at higher speeds
HIGH POSITION is for larger suspension travel, mainly in rough terrain
The OXO has a unique patent on the adjustable suspension system.
The OXO Suspension Adapter Patent : OSAP
The OSAP allows you to alternate the suspension position:
In order to turn your OXO into LOW POSITION use the LOW POSITION kit:
It is recommended that you place the OXO on an uplifted surface such as a
chair or a box, so that the main body is rmly set on the surface and the two
wheels are in the air
Remove the rubber caps and use the 19 mm socket spanner to release the
suspension arms from their location
Once the suspension arm is out of its place, replace the OSAP from LOW to
HIGH in each suspension arm. Keep front and rear OSAP in their respective
places. Assemble back in reverse order. You can use the sketch below for
assistance
REPLACING OSAP FROM HIGH TO LOW
WHEN REPLACING THE OSAP PAY ATTENTION:
Don’t remove the wheel from the arm!
Work on the side of the suspension arm which is
connected to the scooter body
OSAP rear
Suspension arm
19mm washer
Bolt
Rubber cap
19 20
CAREFUL RIDING
CAREFUL RIDING
Get to know your OXO before driving it Test your control over it. Make your
turns slowly and cautiously, and give yourself stopping distance
To gain control over your scooter, practice your rst ride on your OXO in an
open space with no obstacles to disturb you
The OXO requires a short adjustment and break-in period
for all moving parts to adjust themselves into their correct position
Before each ride always:
1. Check your brakes function
2. Check the tires for signs of wear
Spin them to make sure that they are not yet in need of replacing
Make sure that the wheels are freely rotating clear of the brakes
3. Perform a visual inspection :
That all screws and nuts are tight and in place
Note if anything looks amiss, or is showing signs of wear
If you are unsure, bring your OXO to an authorized INOKIM distributor
RIDING TECHNIQUE:
Before riding position your foot as close as possible to the front section of the
scooter, and your other foot on the ground. Make sure that your driving route
is clear
To start riding, boost yourself forwards (as on non-motorized scooters)
with your foot that is on the ground. Place it on the scooter immediately
afterwards and press the thumb lever downwards, tilting your body forwards
so you won’t fall backwards during acceleration
Riding, like most sports, involves risks of injury and
damage. By choosing to ride INOKIM the responsibility
and all inherent risk is on you. It is crucial that you know,
understand and act according to safety rules
Avoid putting body weight on the handle bars whilst accelerating and
decelerating!
Keep one foot behind the other, (it's more comfortable to place one foot
forward and the other one turned backwards at 70-90°, like on skate/
surfboard). It will help you gain more stability
Turns - The turns on INOKIM are done as on skis/surf/snowboard. The handlebar should be in parallel to the body. Before turning look at the approaching direction and make sure turning is safe
Braking - Tilt your weight backwards so that the brake action will come
through the feet and not through the handlebar and steering system.
It is best to learn how to adjust the centre of gravity while stopping,
otherwise there is a dual concern: forward tipping over and/or wear
and breaking of the handlebar and steering system
As you accelerate, lean forwards.
As you brake, tilt your weight backwards!
21 22
SERIAL NUMBER
20171214016
FOLDING MECHANISM ADJUSTMENT
If the folding mechanism is too loose or too tight, you can adjust it
To Tighten / Loosen
1. The red lever for locking the folding mechanism should be tightened in
a way that the steering rod is rm
2. If the red locking lever is too loose, open it and tighten the folding
system by turning the front tension adjuster approximately 30 degrees
clockwise
3. If the red locking lever is too tight, open it and loosen the folding system
by turning the front tension adjuster approximately 30 degrees anticlockwise
4. Test the function until the pressure of the red lever is reasonably hard
and the steering rod is rm
The adjustments needed are VERY small.
Work sensitively, be patient and you’ll get it right!
Each INOKIM has a unique serial number
These numbers can provide information that may be
useful later on for insurance claims and in case of loss or theft
The number is on the BOTTOM REAR SIDE of the board
Write down the serial number of your OXO scooter.
Keep this information separately and in a safe place!
Front tension
adjuster
Red locking lever
23 24
OPERATION & MANAGEMENT
NINGBO MYWAY INTELLIGENT TECHNOLOGY CO.,LTD.
17# PUTUOSHAN ROAD, BEILUN, NINGBO,
ZHEJIANG PROVINCE, CHINA 315806
WWW.INOKIM.COM | GLOBAL@INOKIM.COM
Join / create INOKIM RIDERS in your city!
Loading...