Hold dow n t he mid dle butt on of the m oni tor for 5 s eco nds to enter int o S tan dar d
Settings Mode (left gra phi c below). The fir st tire pos iti on will be selected. P res s
the “ ” or “ ” button to s et th e req uir ed pr ess ure f or this tire p osi tio n the n pre ss
the middle b utt on to s ele ct th e nex t tir e and rep eat t his s equ enc e to se t the
standard pressure on each of the remaining tir es.
4
TYRE GUARD
3
TYRE GUARD
Installation of the Sensor and anti-theft device
A
Valv e
Anti-t hef t
Devce
Driver
c
The sensors of the INNOTECHRV TPMS-X have
an optional a nti the ft r ing to p rev ent the sensors
being sto len . If you wis h to fit these then , wit h
the sensor off the v alv e ste m, pl ace t he an titheft rin g ove r the val ve stem, with keye d face
facing ou t, rep lac e the s ens or and the n w ith the
anti-theft ring k nob s fi tte d to the slots of t he
sensor ti ght en the grub s cre ws with th e h ex key
provided.
Programming Standard Settings
Ba
r
Pressure
Temp
Bar
Pressure
C
Installation of the Monitor
InnoTechRV InnoTechRV
Tir e alig nme nt mode
Hold do wn t he b utto ns s imu ltaneou sly on t he m oni tor for 5 second s to ent er
tire a lignmen t mode, and pres s e ithe r “ ” o r “ ” bu tton to sele ct t he spec ifi c ti re that
needs to b e ali gned .
Screw a sen sor to th e Tir e va lve s tem and the curr ent pres sur e wi ll be dis pla yed agai nst the
corres pon ding fl ashi ng Tire ico n on the scr een. On ce the Tire is ali gned su cces sfu lly the
green lig ht appe ars on t he moni tor. The red LED ligh t a ppe ars on the moni tor if t he s ens or
hasn’t b een a lign ed an d “- - -” al so ap pears on th e mon itor.
When all tire sens ors hav e be en a ligned with the m oni tor, exit tire ali gnme nt mode by ag ain
holdin g d own the “ ” and “ ” , butto ns simu lta neou sly on t he m oni tor unt il the mon itor
beeps (a ppr ox 5 sec ond s).
To che ck th e pre ssu res a nd te mper atu res, scroll throu gh th e sel ect ed ti re po sitions usin g the
left or ro ght b utto ns. The mon ito r will i ndi cate the pr ess ure an d the n the t empe rat ure of e ach
tire. Aft er y our chec ks are comp let ed, the backlig ht w ill go o ut a nd the moni tor wil l in dicate
the Tire pr ess ure of t he se lect ed Tir e.
“ ” and “ ”
Note: If the sens or is to be remo ved from o ne valve a nd fitted to anot her valv e, you must
delete the curr ent sett ing on t he mo nit or an d re ali gn th is s enso r to the new t ire . To del ete an
aligne d sen sor f rom a t ire , whilst in tire alig nme nt mo de, s elec t the t ire p osi tion and t hen hold
down the m idd le but ton u ntil “ - - -“ ap pears on th e mon itor.
Note: Th e moni tor m ay in itia lly s how ab nor mal itie s unt il you h ave s et yo ur req uir ed pressu res
and unit s of meas ure ment . The se will be done in the Stan dar d Pres sur e Setting and unit
select ion s etti ng be low.
Note:
1. Always i nst all t he sensor wh en the Tir e is cold
2. Please c hec k ea ch Tir e va lve is no t damaged.
3. Check to ens ure th ere ar e no leaks and the
se nso rs are fi rml y se cur ed to eac h Tir e valve.
The monitor m ay be mou nte d using the p ede sta l sup pli ed. The moni tor can be
fixed t o a sui tab le surface in the v ehi cle , sun visor, dashboar d etc . It ha s a built -in
lithium battery or you may wish to use the charger pro vid ed t o po wer the mon ito r
continuously.
Once you h ave c omp let ed sett ing all the tire pressures, then s et your pre fer red
units o f tem per atu re and pr ess ure measurement, “kpa ”, “B ar” , “PSI” a nd “k gf/ cm2 ”
for pressure units a nd “F” an d “ C” for te mpe rat ure , b y p res sin g t he “ ” o r “ ”
buttons. Hol d d own the midd le button for 5 s eco nds to exi t t he Standard S ett ing s
mode.