Innotech ICS01, ICS02 User Manual

Page 1

DS 13.01

September 2013

Overview

The ICS series Control Stations form par t of the Maxim & Genesis Direct Digital Controller range and provide a simple unitary Human Machine Interface (HMI). The HMI oers on/o, setpoint and fan speed control. The HMI is powered by 24VAC and connect s directly to the Globals Comms network.

Each ICS can communicate with a designated controller on the network. The ICS units are configured via the Keypad, are compatible with most existing Innotech digital produc ts and are capable of operating at both fast or slow comms.

The interface to the controller is via global transmit and receive blocks, the configuration simply uses the ICS address to form part of the unique point name.

Features

• One numerical value input

• One numerical value output

• One momentary push button digital input

• One LED indication digital output

• One fan speed input (ICS02 only)

• Housed in a switchplate that mounts in standard electrical wall plates

• Isolated RS485 interconnection between Innotech Controllers

• Adjustable user input range

• Adjustable decimal place

• Configurable power on settings

Applications

The Innotech Control Station extends the capabilities of Innotech controllers by providing a numerical value output, numerical value input, push button digital input and a single LED display output for distributed control via RS-485.

The Innotech Control Station provides a visual display of a control value and a means to set a parameter. It is not intended for use on a large controller network as this aects the operation.

Installation

• Strictly follow the guidelines when installing the Comms wiring as outlined in the Genesis System Comms Wiring Recommendations.

• Mount the Innotech Control Station in a dry and clean location free of excess vibration.

Wiring

• DO NOT connect 240VAC to any terminals.

• The cable used for RS485 Comms must be shielded single twisted pair, 120 ohms character impedance, 36 to 45pF per metre capacitance between conductors.

• The Comms cable must be organised as a bus topology. That is, starting at one end, devices are connected to it until the other end of the cable is reached. No “stubs” are allowed. To connect a device to the cable, a cut is made in the cable at the point where the device is to be situated along it. Then, the two new ends of the cable are wired into the device. The shields from the two new ends are then terminated into the terminals marked SHLD1.

• Refer to the Genesis Network Installation Instructions and DS99.04 Cabling Manual for more information.

Approvals

The Innotech Control Station conforms to the requirement s for RCM labelling.

ICS0x

Innotech Control Station

MODEL:

ICS01: ON/OFF, Set Point ICS02: ON/OFF, Set Point and 3 Speed Fan

Model Number Designations

Innotech Control Station - ICS0x

Model

On/O

Temp.

Display

Setpoint

Adjust

Run Status Fan Speed

ICS01

    

ICS02

    

Page 2

Page 2 DS 13.01 - ICS0x - Innotech Control Station September 2013

Specifications

Power Supply

• Voltage: 24VAC ±10% @ 50/60Hz

• Power Consumption: 3VA max

Inputs

• Push buttons for adjusting control values

• Push button for momentary input of “digital function”

Outputs

• No physical outputs

• Display of Temperature and Setpoint

Terminal Identification

1 24VAC Supply 2 0VAC Supply 3 Earth

Terminal 3 is for the protection of the Comms circuitr y and must be connected to a good electrical bonded Earth.

COMMS Connection

S1 Shield from incoming Comms Cable. + RS485 (+) signal.

- RS485 (-) signal. S2 Shield from outgoing Comms Cable. Do not connect. Only used on REM Networks

Temperature Ratings

• Storage 0 to 50°C non-condensing

• Operating 0 to 40°C non-condensing

Enclosure

The Innotech Control Stations are housed in switchplate that mounts in standard electrical wall plates. Colour: White Mounting: Wall mounted

Innotech Controller Configuration

The interface to the Innotech Control Station is with the use of Global Blocks in the configs executed on Innotech Controllers (Genesis and Maxim families). The Innotech Control Stations have the following pre-defined Global Blocks:

• CS:xxx AI Set Point Adjust

• CS:xxx AO Temperature Display

• CS:xxx DI On/O

• CS:xxx DO Run Status

• CS:xxx FS (ICS02 Only) Fan Speed (0, 1, 2, 3)

xxx represents the three digit address. (ie. Address 10 is 010, Address 5 is 005)

To access the points on the Innotech Control Station, Global Blocks with names corresponding to the above names need to be placed in the config. The figure below provides an example for an ICS02 at network address 2:

Page 3

DS 13.01 - ICS0x - Innotech Control Station

September 2013

Program Functions Of The Innotech Control Station

To enter Programming mode depress and hold the and

buttons for 5 seconds. The display will become blank indicating that you are in the Programming Mode. Release both keys and the display will show parameter 0.

Whilst in the programming mode the following buttons are active:

Change to the next parameter

Increase the current parameters value

Decrease the current parameters value

Parameter 0 - Global Address

The display will show the current GLOBAL Address of the device.

• The range of address is 2 to 127. The default address is 2.

Parameter 1 - Maximum Input Value

The display will show the Maximum Input Value to which the module’s input can be set.

• The range of Maximum Input Value is 0.0 to 99.9

• The factory default setting is 30.0

Parameter 2 - Minimum Input Value

The display will show the Minimum Input Value to which the module’s input can be set.

• The range of Minimum Input Value is 0.0 to 99.9

• The factory default setting is 15

Parameter 3 - Decimal Places

The display will show the number of decimal places which will be displayed for both the input and output values.

• The range of Decimal Places is 0 to 2

• The factory default setting is 1

Parameter 4 - Baud Rate

The display will show an indication of the communications Baud Rate:

• 0 4800 Baud

• 1 38400 Baud

• The factory default setting is 38400 Baud

To exit the Programming Mode depress the and buttons and the new setting will be saved.

IF PARAMETER 4 IS CHANGED, POWER TO THE ICS0x MUST BE RECYCLED, AFTER EXITING PROGRAMMING MODE.

Start Up Default Settings

The Innotech Control Station Module can be set to start with default settings for Set Point, Run Status and Fan Speed (ICS02 only). To set the start up default settings adjust the Innotech Control Station to the desired Set Point, Run Status and Fan Speed (ICS02 only) and then press and hold the and buttons for 5 seconds.

The display will become blank indicating that the new default start up settings have been saved.

Operating Functions Of The Control Station

Numerical Output

The Innotech Control Station will display a 4-digit value with up to 3 decimal places.

Numerical Input

The Innotech Control Station will provide a 4- digit value with up to 3 decimal places to Innotech controllers on the global network. The value can be modified by pressing the button to increment by the least significant digit or the button to decrement by the least significant digit.

Digital Input Value

The button on the Innotech Control Station provides a digital input value to the Innotech Controllers. This operates as a standard momentar y switch, i.e. Pressing the button produces a short period ON value to the controller.

Digital Output LED

The Innotech Control Station displays a digital state via the system LED during normal operation. This LED, however, cannot be overridden whist the Digital Input Value is in a transitional state.

Fan Speed Button (ICS02 Only)

The button provides means of set ting a fan speed. Pressing the

button cycles bet ween low/medium/high fan speeds. This is indicated on the LEDs above the button. The button and LEDs are disabled whilst the Control Station is o (ie. there is no ventilation only mode).

Page 4

Page 4 DS 13.01 - ICS0x - Innotech Control Station September 2013

1 2 3

24V 0V EARTH

24V

EAR T H

Global Comms Wiring

Daisy Chained

End Device

From Previous Controller

From Last Controller

To Next Controller

R 485(+)S

R 485( - )S

YOUR DISTRIBUTOR

Australian Owned, Designed & Manufactured

by Mass Electronics Brisbane

Phone: +61 7 3421 9100 Fax: +61 7 3421 9101 Email:

sales@innotech.com.au www.innotech.com.au

The INNOTECH d evice and the word I NNOTECH are registe red or unregiste red trademark s of Mass Electro nics Pty Ltd in A ustralia, USA an d other countries

Innotech ICS01, ICS02 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual