T2TZ-30T BTC
USER MANUAL
Catalogue
1.Overview ............................................................................................................ 0
2. Assemble the miner ......................................................................................... 2
2.1 Check the miner before power on ........................................................................................ 2
2.2 Assemble&Operate ............................................................................................................... 3
3.Operate the miner.............................................................................................. 4
3.1 Enter the miner console........................................................................................................ 4
3.2 Set up the pool ...................................................................................................................... 5
3.3 check the hashrate of the miner ........................................................................................... 6
3.4 network configuration .......................................................................................................... 6
3.5.1 Overview ............................................................................................................................ 7
3.5.2 Upgrade.............................................................................................................................. 8
3.5.3 Modify the password ......................................................................................................... 8
3.5.4 Reboot ................................................................................................................................ 8
3.5.5 Factory reset ...................................................................................................................... 9
1.Overview
Part Number
T2TZ-30T
Algorithm
Sha256
Size (L×W×H)
422mm(L)*142mm(W)*213mm（H）
Net Weight
9.5KG
Operating Temperature
0--40 ℃(device junction temperature)
Network Connection
Ethernet
Mode
Performance
Factory
Balance
Efficient
Hashrate
30TH±5%
29TH±5%
26TH±5%
24TH±5%
Power dissipation
2200W±10%
2100W±10%
1900W±10%
1620W±10%
Specifications
Typical Hashrate and Power Dissipation of the Four Mode:（You can set the mode
follw the manual 3.5.1）
2. Assemble the miner
2.1 Check the miner before power on
Check the warranty sticker is well or not, especially the hashboards
PSU port side. If the warranty sticker is damaged when you received the
miner, please contact our After-sales.
Before you power on the miner, shake the miner softly, if you can hear
the sound of metal banging on metal, please contact our After-sales.
Check if the fan work well, if you find the fans broken please contact
our After-sales.
The cable connection should be same as the follow picture.
Note:
There is a led on each hashboard, which can show the work status of the hashbaord.
When the miner start to work, the led
Solid---workig well
Blink---the hashboard overheat, please check the fans of the miner and the room temp
Off---the hashboard don’t work, please try to reboot the miner or change the data cable. You
can contact our after-sales team if the problem is still exist.
2
Innosilicon After sales Team
Email:minersupport@innosilicon.com.cn
AC Cable port
Switch
Ethernet port
2.2 Assemble&Operate
Connect the miner and the router by the Ethernet cable, then the miner can start to run after
power on the miner.
Normal Led：Solid means static IP; Blinking means DHCP
Fault Led：On means network has something wrong; Off means OK.
IP SET button:
Press it 1—4 seconds, it will (1) show the IP of the miner in the “Set IP” tool; (2) change the miner to
Static IP mode and modify the IP to the IP range you set in the “Set IP” tool
Press it 4—15 seconds, the miner will become to DHCP and the settings of the miner should be restore
to default.
Press it more than 20 seconds to switch the Dynamic (Static) IP to Static (Dynamic)
RESET button: Your miner will restart if you press it..
3
Innosilicon After sales Team
Email:minersupport@innosilicon.com.cn
Press the IPset button 1 to 2 seconds then
the IP of the miner will show here
3.Operate the miner
3.1 Enter the miner console
DHCP is the default IP mode of the miner, find the IP via the router or the IP scanner. Or you can use the
“SetIP” tool which is developed by ourselves to search the IP. Download link is:
https://drive.google.com/open?id=1O3D4OYfFfYYT5prN6J6DgrW1bFJrCKmx
a. Put the tool on the PC which is connect with the same router with the miner, then double click
the tool and choose the language.
b.Report the miner IP
Innosilicon After sales Team
Email:minersupport@innosilicon.com.cn
4
add the “stratum+tcp” will be better
Enter the IP of the miner on the browser and press the Enter button. Chrome is the suggested browser.
3.2 Set up the pool
You can use the suggested pool as below:
1 f2pool：stratum+tcp://btc-65536.f2pool.com:3333
2 poolin: stratum+tcp://btc-bj.ss.poolin.com:1800 or stratum+tcp://btc-sz.ss.poolin.com:1800
3 ckpool：stratum+tcp://cn.ckpool.org:443 or stratum+tcp://pool.ckpool.org:3333
4 btc.top：stratum+tcp://t2.btc.top:8888 or stratum+tcp://bak.t2.btc.top:3333
5 slushpool：stratum+tcp://stratum.slushpool.com:3333
Innosilicon After sales Team
Email:minersupport@innosilicon.com.cn
5
3.3 check the hashrate of the miner
After set up the pool, the miner will mine for you.
3.4 network configuration
6
Innosilicon After sales Team
Email:minersupport@innosilicon.com.cn
3.5 Other pages
3.5.1 Change the operate mode
There are 4 modes can be choosed, please click the “Save” after you set the mode.
3.5.2 Overview
Innosilicon After sales Team
Email:minersupport@innosilicon.com.cn
7
3.5.3 Upgrade
1
1
3.5.4 Modify the password
3.5.5 Reboot
8
Innosilicon After sales Team
Email:minersupport@innosilicon.com.cn
3.5.6 Factory reset
Innosilicon After sales Team
Email:minersupport@innosilicon.com.cn
9
Loading...