InnoMedia MTA8328-1U Administrator's Manual

InnoMedia MTA8328-1U Administrative Guide

InnoMedia

MTA8328-1U

Administrative Guide

Version: 1.2

January, 2014

www.innomedia.com

InnoMedia MTA8328-1U Administrative Guide

Date

Version

Notes

2013/09/17

V1.0

Based on firmware V1.0.4.3

2013/09/23

V1.1

Based on firmware V1.0.5.2

2014/01/17

V1.2

Based on firmware V4.0.0.1

About This Document

This document shows the usage of all the features available of MTA8328-1U. It includes features, feature descriptions, and their associated provisioning tags. More details about the provisioning tags and the default values are given in the Appendix (A2) section.

Revision History

InnoMedia MTA8328-1U Administrative Guide

Table of Contents

ABOUT THIS DOCUMENT ................................................................................................................................... 2

1 INTRODUCTION .............................................................................................................................. 6

1.1 PRODUCT OVERVIEW ......................................................................................................................... 6

1.2 PACKAGE CONTENTS .......................................................................................................................... 6

1.3 SETUP ............................................................................................................................................. 6

2 HOME – DEVICE STATES .................................................................................................................. 8

3 NETWORK ..................................................................................................................................... 10

3.1 IP ADDRESS .................................................................................................................................... 10

3.1.1 USB Network IP Address Setting ........................................................................................... 10

3.1.2 Ethernet ................................................................................................................................ 12

3.1.3 Host and DNS Servers ........................................................................................................... 14

3.1.4 Master DNS ........................................................................................................................... 15

3.1.5 TOS Setting ........................................................................................................................... 15

3.1.6 VLAN ..................................................................................................................................... 16

3.1.7 Dynamic DNS ........................................................................................................................ 17

4 TELEPHONY ................................................................................................................................... 19

4.1 PROFILE CONFIG ............................................................................................................................. 19

4.1.1 Profile Setting ....................................................................................................................... 19

4.1.2 SIP Server Setting .................................................................................................................. 20

4.1.3 Codec Setting ........................................................................................................................ 24

4.1.4 SIP Timer Setting ................................................................................................................... 25

4.1.5 DigitMap Setting ................................................................................................................... 27

4.1.6 Feature and Service Code Setting ......................................................................................... 31

4.1.7 Fax Setting ............................................................................................................................ 34

4.2 PORT CONFIG ................................................................................................................................. 35

4.2.1 SIP Account Setting ............................................................................................................... 35

4.2.2 Features Setting .................................................................................................................... 37

4.2.3 Line Setting ........................................................................................................................... 39

4.2.4 Speed Dial ............................................................................................................................. 39

4.3 TELEPHONY REGION AND MISC SETTING .............................................................................................. 40

InnoMedia MTA8328-1U Administrative Guide

4.3.1 Media Port Setting ................................................................................................................ 40

4.3.2 Regional Setting .................................................................................................................... 41

4.3.3 Tone Cadence Setting ........................................................................................................... 43

4.3.4 Ring Cadence Setting ............................................................................................................ 46

4.4 LINE DIAGNOSTICS ........................................................................................................................... 48

4.4.1 GR909 Test ............................................................................................................................ 48

5 SYSTEM ......................................................................................................................................... 50

5.1 ACCOUNT SETTINGS ......................................................................................................................... 50

5.1.1 Administrator Account Setting ............................................................................................. 50

5.1.2 User Account Setting ............................................................................................................ 50

5.2 FIRMWARE UPLOAD ......................................................................................................................... 51

5.3 REBOOT ......................................................................................................................................... 51

5.4 RESTORE TO FACTORY ...................................................................................................................... 51

5.5 RESTORE USER SETTING .................................................................................................................... 52

5.6 PAGE PERMISSION ........................................................................................................................... 53

5.7 PROVISIONING SETTING .................................................................................................................... 54

5.7.1 Provision Server Setting ........................................................................................................ 54

5.8 EMS SETTING ................................................................................................................................. 57

5.8.1 EMS Server ............................................................................................................................ 57

5.9 SNMP SETTING .............................................................................................................................. 60

5.10 TRACE LOG..................................................................................................................................... 60

5.10.1 Trace Log Setting ............................................................................................................. 60

5.11 REMOTE ACCESS ............................................................................................................................. 62

5.11.1 Remote Access Setting ..................................................................................................... 62

5.12 SYSTEM TIME ................................................................................................................................. 63

5.12.1 Time Setting ..................................................................................................................... 63

5.13 LANGUAGE ..................................................................................................................................... 65

5.14 PING HOST ..................................................................................................................................... 65

5.15 CONFIG FILE ................................................................................................................................... 66

5.15.1 System Config ................................................................................................................... 66

5.16 CERTIFICATE & KEY .......................................................................................................................... 66

6 TROUBLESHOOTING ...................................................................................................................... 68

6.1.1 Telephone has no dial tone ................................................................................................... 68

InnoMedia MTA8328-1U Administrative Guide

7 HARDWARE SPECIFICATIONS ........................................................................................................ 69

APPENDIX A1. LED STATES ..................................................................................................................... 70

APPENDIX A2. DEFAULT VALUES AND ALLOWABLE VALUES ................................................................... 72

InnoMedia MTA8328-1U Administrative Guide

Item List

Quantity

MTA device

1

USB Cable

1

Step 1

Install the host driver software; make sure the driver is successfully installed.

** Please be aware, skipping this step or incorrectly installing the driver will result in the failure of later activities in this manual.

** For more information, please go to our host driver installation guide.

Step 2

Network – Connect the USB cable into the “PC USB” port on the MTA and connect the other end into an available USB port on the PC or laptop

Step 3

Phone – Connect your phone to the “PHONE” port on the MTA.

1 Introduction

1.1 Product Overview

MTA8328-1U uses your broadband connection to deliver voice quality and features equivalent to those of the PSTN. It is compatible with standard analog telephone sets, and it is very easy to install and configure.

MTA8328-1U can be connected via a USB cable (to a PC or laptop) to obtain network connectivity.

1.2 Package Contents

The MTA8328-1U package comes with the following items:

1.3 Setup

This section provides a step-by-step procedure to install the MTA8328-1U and setup the system for connecting to a broadband network.

Follow these steps to setup the MTA.

InnoMedia MTA8328-1U Administrative Guide

Step 4

Dial ***1 to obtain an IP address to get the connection for MTA8328-1U

Figure 1. Setup the MTA device to the PC In Addition to Router/Broadband Device Setup

InnoMedia MTA8328-1U Administrative Guide

2 Home – Device States

Login Screen

Setup and Configuration of the MTA8328-1U can be managed via a Web Browser interface. Once the MTA is connected as outlined in Figure 1 proceed to access and configure the MTA8328-1U via a Web Browser interface.

The default Username is: admin

The default Password is: password Note: The username and password are based on the desire of the service provider.

Figure 2. Login Screen (Username and Password)

InnoMedia MTA8328-1U Administrative Guide

Home Page

The Home page displays the device’s current status.

Figure 3. Current status of MTA8328-1U network connection, Account Registration, and Firmware

Information

Channel Information

VoIP SIP User ID, Name, Registration Status, and Line State.

System Information

MAC Address, Date and Time, System Up Time, and Last Provisioning Status.

Version Information

Hardware Version and Firmware Version.

Network Information

Network connection information and type of connection.

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

IPv4 Enabled

Enable IPv4.

Network.Inter face.%d.IPV4. Enable

3 Network

The Network page allows to configure the MTA8328-1U network parameters.

3.1 IP Address

Configuring the IP address parameters for this device. The MTA 8328-1U supports the following methods to acquire IP address: DHCP and Fixed IP.

3.1.1 USB Network IP Address Setting

Configure the IPv4 IP address for the device. Click the “IP Address” menu from the left panel.

Note: The marked area of Figure 4 will only be displayed when Fixed IP is selected.

IPv4 Setting

Figure 4. USB Network IP Address Setting

InnoMedia MTA8328-1U Administrative Guide

Connection Method

Available options:

 DHCP  Fixed IP

DHCP:

Network.Inter face.%d.IPV4. DHCP

Fixed IP: Gateway Network.Inter face.%d.IPV4. Gateway

Fixed IP: NetMask

Network.Inter face.%d.IPV4. NetMask

Fixed IP: IPV4 Address

Network.Inter face.%d.IPV4. IPAddr

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

Enable MAC cloning

Allows you to enable MAC Cloning, and set the MAC Address you wish to clone.

Network.Inter face.%d.Mac.E nableMacCloni ng

WAN Mac Address

Enter the Mac address you wish to clone.

Network.Inter face.%d.Mac.M ACClone

Link Setting

Allows you to set MTA8328-1U Link Mode and Link Speed. If Auto-Negotiation is Enabled, Link Mode and Link Speed are Auto-negotiated, and if Disabled, you can configure the Link Mode and Link Speed. When Auto-negotiation is disabled, more options are available for you to configure. Note: Both Link Mode and Link Speed Provisioning Tags should be added at the same time.

Autonegotiation

When this box is checked, both the MTA and the connected switch will automatically negotiate link mode and speed.

Check the tags of Link Mode and Link Speed.

Link Mode

Force Ethernet connection to desired duplex mode. (This option will not be displayed if Autonegotiation mode is enabled)

Network.Inter face.%d.Link. Mode

3.1.2 Ethernet

Figure 5. Ethernet Setting

Figure 6. Autonegotiation Disabled

InnoMedia MTA8328-1U Administrative Guide

Link Speed

Force Ethernet connection to desired link speed. (This option will not be displayed if Autonegotiation mode is enabled)

Network.Inter face.%d.Link. Speed

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

Host Name

Configure the host name for the device.

Network.Hostn ame

Domain

Configure the domain name for the device.

Network.Domai n

DNS Server Setting

Allows configuration of up to three DNS Servers.

Network.DNS.% d.Server

3.1.3 Host and DNS Servers

Configure the host and the DNS server information provided by your network operator.

Figure 7. Configuring the host information on the device

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

DNS Server

Configure the DNS information specified by the VoIP service provider.

System.Master DNS.%d.Server

3.1.4 Master DNS

“Master DNS” is the IP address of the domain name server specified by the telephony service provider rather than the internet service provider. If “Master DNS” is configured, the MTA gets related services

from this configured server and performs voice communication functions. The MTA acquires DNS server information from the following methods in the priority shown.

1. Master DNS

2. DHCP Option (USB Network IP Address Setting)

3. Manually configured DNS (Host and DNS Servers)

Figure 8. Configuring the Master DNS Information

3.1.5 TOS Setting

ToS (Type of Service) is a part of the IPv4 header which is used for precedence, or in other words categorizing traffic classes. In summary, the higher the value of the IP Precedence field, the higher the priority of the IP packet. In the more modern form, the ToS is used for DSCP.

Figure 9. ToS Setting

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

TOS Setting

Host Traffic1

Network.Inter face.%d.DSCP. Host

VoIP Signal Traffic

Network.Inter face.%d.DSCP. Signal

Voice Traffic

Network.Inter face.%d.DSCP. RTP

Field Name

Description

Prov Tag

Enable VLAN Tagging

Check the option box if you want to enable the LAN port VLAN Setting.

Network.Inter face.%d.VLAN. Enable

3.1.6 VLAN

Configure the VLAN (virtual LAN) to connect a VLAN switch and perform appropriate designations for LAN traffic demarcations. Enable VLAN, enable TOS Priority and configure VLAN values and priorities.

1

Contact InnoMedia for feature availability.

Figure 10. VLAN Setting

InnoMedia MTA8328-1U Administrative Guide

Enable TOS to Priority Mapping

Check the option box if you want to enable the LAN port priority mapping feature.

Network.Inter face.%d.VLAN. TosMap

VLAN ID for Host Traffic2

Enter the LAN port traffic VLAN ID in the field

Network.Inter face.%d.VLAN. VID

VLAN Priority for Host Traffic3

Enter the LAN port Traffic Priority value in the field.

Network.Inter face.%d.VLAN. Priority

VLAN ID for Signal Traffic

Enter the VLAN ID for Voice Signaling in the field.

Network.Inter face.%d.VLAN. SigVID

VLAN Priority for Signal Traffic

Enter the priority value for Voice Signaling in the field.

Network.Inter face.%d.VLAN. SigPriority

VLAN ID for Voice Traffic

Enter the VLAN ID for Voice Traffic in the field.

Network.Inter face.%d.VLAN. RtpVID

VLAN Priority for Voice Traffic

Enter the priority value for Voice Traffic in the field.

Network.Inter face.%d.VLAN. RtpPriority

3.1.7 Dynamic DNS

Dynamic DNS (DDNS) updates a name server in the Domain Name System (DNS) with the active DNS configuration of its configured hostnames, addresses or other information.

If this feature is used, click the “Add” button and the DDNS Entry Setting Page will display, as shown in

below.

2

Contact InnoMedia for feature availability.

3

Contact InnoMedia for feature availability.

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

Service Provider

The DDNS service provider.

Network.DDNS. %d.ServicePro vider

Dynamic DNS Enable

DDNS Setting allows you to configure your Dynamic DNS Service Provider.

Network.DDNS. %d.Enable

Domain Name

The domain name that is assigned to this MTA device.

Network.DDNS. %d.DomainName

User Name

The user name used for the selected DDNS to authenticate this MTA device.

Network.DDNS. %d.UserName

User Password

The password used for the selected DDNS to authenticate this MTA device.

Network.DDNS. %d.Password

Check Interval

The interval for this MTA device to check its IP address, and to report to the DDNS if IP address has changed.

Network.DDNS. %d.CheckInter val

Force Update Interval

The interval for this MTA device to update its current IP address to the DDNS no matter IP address has changed or not.

Network.DDNS. %d.ForceInter val

Figure 11. DDNS Setting

InnoMedia MTA8328-1U Administrative Guide

Add Click Add to create a new profile. Then enter the desired Profile Name in the Profile Name field

Save

Save a profile.

Edit Edit the existing profile.

Delete

Delete the profile.

Field Name

Description

Prov Tag

Profile Name

Set up your profile name

VoipConfig.Pr ofileSetting. %d.ProfileNam e

4 Telephony

The Telephony section is used to configure SIP Parameters such as the SIP Proxy, SIP Domain and SIP User Account.

Figure 12 Configuring Telephony options

4.1 Profile Config

Profile List – List of profiles created. Up to 4 profiles can be created.

Profiles include SIP Server/Proxy Settings, Codec Settings, SIP Timer Settings, Digitmap Settings, FXS Settings, Feature and Service Code Settings, Fax Settings and Regional Settings which are described in the following sections.

4.1.1 Profile Setting

Figure 13. Setting up the profile name.

InnoMedia MTA8328-1U Administrative Guide

Profile ID

Up to 4 profiles can be created. (The profile ID correspond with the No. in Profile List.)

VoipConfig.Pr ofileSetting. %d.profileID

Figure 14. Up to 4 Profile ID(s) can be created and displayed.

4.1.2 SIP Server Setting

Figure 15. SIP Server Settings

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

SIP Proxy Server

Proxy Server

IP/FQDN of SIP Server. Can enter more than 1 proxy by separating each with a comma (,).

VoipConfig.Pr ofileSetting. %d.SIPProxy

Local SIP Port

SIP port used by MTA

VoipConfig.Pr ofileSetting. %d.LocalPort

Enable Outbound Proxy

Enable/Disable Outbound Proxy

 Checked (enabled): the MTA does DNS

A record lookup only.

 Unchecked (disabled): the MTA does

both DNS SRV and A record lookup. The server may respond with additional A records for SRV requests.

VoipConfig.Pr ofileSetting. %d.OutboundPr oxy

SIP Domain

Domain name of SIP service provider, used as part of user URI.

VoipConfig.Pr ofileSetting. %d.SipDomain

Access Network Info

RFC 3455 P-Access-Network-Info header support.

VoipConfig.Pr ofileSetting. %d.SipPAccess Info

Allowed for Reg Retry

List of error codes that respond to REGISTER requests. The MTA will continue to retry register only for error codes in this list. A negative list can be created by putting a leading ~ in front of the list; this will cause the MTA to not retry to REGISTER when it sees any of these error codes. This can prevent an infinite loop of REGISTERRESPONSE(s)

VoipConfig.Pr ofileSetting. %d.RegRetryRe sp

SIP Ping Proxy

MTA sends SIP OPTION ping message to an assigned server as a keep-alive message.

VoipConfig.Pr ofileSetting. %d.SipPingPro xy

SIP Option

100 Rel Support

Enable 100 Rel response support.

VoipConfig.Pr ofileSetting. %d.SipSupport 100rel

InnoMedia MTA8328-1U Administrative Guide

Disable Rport Support

Do not append rport (received port number) in the Via header.

VoipConfig.Pr ofileSetting. %d.NoRport

Notify Flash Support

Send a SIP NOTIFY hook flash event message during the call when detect a hook flash.

VoipConfig.Pr ofileSetting. %d.NotifyFlas h

Info Flash Support

Send a SIP INFO hook-flash event message during the call when detect hook flash.

VoipConfig.Pr ofileSetting. %d.SipInfoFla sh

Short header Support

Send SIP Headers in short format (compact form) to reduce message packet size.

VoipConfig.Pr ofileSetting. %d.ShortHeade r

Enable Reregistration Credential

Enable Re-registrations to carry the previous successful authentication credentials.

VoipConfig.Pr ofileSetting. %d.RegCredent ial

OutOfBand DTMF by SIP

Use SIP NOTIFY to send DTMF.

VoipConfig.Pr ofileSetting. %d.UseSipDTMF

RFC2833 DTMF

Use RFC2833 for sending DTMF digits.

Available options:

 Negotiated – MTA and SIP Server

negotiate if 2833 is enabled or not.

 Always off – 2833 is never used.  Always on – 2833 is always used.

VoipConfig.Pr ofileSetting. %d.Rfc2833DTM F

Send EndOfDial Pound

Enable the inclusion of "#" in the INVITE when using "#" as the end of dialing command.

VoipConfig.Pr ofileSetting. %d.PoundChara cter

Send UA Header

Allow MTA to send UA Header in SIP message.

VoipConfig.Pr ofileSetting. %d.UseUAHeade r

InnoMedia MTA8328-1U Administrative Guide

UA Header Format

UA Header sent out is modifiable.

(Note: If “Short header Support” is enabled,

there will be no UA Header in SIP messages.)

Available parameters:

 Model name ($MOD)  MAC ($MAC)  Version ($VER)  Config file last loaded ($CFG)

Example Syntax: $MOD $MAC $VER $CFG.

Output: SIP User-Agent: MTA-8328-1U 001099112233 V1.0.4.3 /Provisioning/Config/xyz.cfg

VoipConfig.Pr ofileSetting. %d.UserAgent

Refer at End of 3way Call

Send REFER when mixer hangs up, so the other two parties can continue the conversation.

VoipConfig.Pr ofileSetting. %d.ThreeWayEn dRefer

Trusted Proxy Only

Use only trusted proxies. Only use proxies in the Proxy Server list or ignore the request.

VoipConfig.Pr ofileSetting. %d.TrustedPro xy

Accept rsync

When enabled, device will re-provision when an rsync is received, and reboot if a check-sync is received.

VoipConfig.Pr ofileSetting. %d.SipRsync

Call Hold with Zero IP

Use 0.0.0.0 in SDP for hold.

VoipConfig.Pr ofileSetting. %d.SipZeroIpH old

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

Preferred Codec List

List the Codecs to be enabled for this profile and the order of importance.

Available Codecs:

 PCMU/8000 – Set Ptime  PCMA/8000 – Set Ptime  G723/8000  G726-32/8000  G729/8000  iLBC/8000

VoipConfig.Pr ofileSetting. %d.NumCodecs

VoipConfig.Pr ofileSetting. %d.Codecs.%d. CodecId

VoipConfig.Pr ofileSetting. %d.Codecs.%d. PTime

VoipConfig.Pr ofileSetting. %d.Codecs.%d. Name

Telephone Event

2833 payload type

VoipConfig.Pr ofileSetting. %d.Codecs.%d. RFC2833Type

4.1.3 Codec Setting

Configure allowable voice codecs by service providers for telephony services.

Figure 16. Codec Setting

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

Basic Timer

Round Trip Time Estimate (T1)

Estimated time it takes for a packet to make a round trip from the device to the far end and back.

VoipConfig.Pr ofileSetting. %d.ExpoBackof f

Max Retransmit Interval (T2)

The maximum retransmit interval for nonINVITE requests and INVITE responses.

VoipConfig.Pr ofileSetting. %d.ExpoCap

Invite Retry Times

The number of times the device will send an INVITE if no response to initial INVITE.

VoipConfig.Pr ofileSetting. %d.InviteRetr y

4.1.4 SIP Timer Setting

SIP timers define the transaction expiration timers, retransmission intervals when UDP is used as a transport, and the lifetime of dynamic TCP connections. The retransmission and expiration timers correspond to the timers defined in RFC 3261.

Figure 17. SIP Timer Setting

InnoMedia MTA8328-1U Administrative Guide

Non Invite Retry Times

This field specifies the maximum number of times that a SIP message other than an INVITE request gets retransmitted. According to RFC3261, Non-INVITE requests are retransmitted at an interval which starts at T1 and doubles until it hits T2.

VoipConfig.Pr ofileSetting. %d.NonInviteR etry

Register Expiration Time

Time to wait after a registration before it expires. (Note: If value is greater than 1200 sec., if will re-register 600 sec. before registration time expires. If less than or equal to 1200 sec., it will re-register when half of the expiration time expires.)

VoipConfig.Pr ofileSetting. %d.RegInterva l

Register Retry Interval

The time interval in seconds in which the SIP Device will retry registration when the retry interval expires, after a SIP Registration

failure. It also depends on the “Allowed for

Registration Retry” configuration if it will try again or not.

VoipConfig.Pr ofileSetting. %d.RegRetryTi me

Session Timer

Signal Bullet Interval

Signal keep alive packet, time between sending a blank keep-alive UDP packet.

VoipConfig.Pr ofileSetting. %d.BulletInte rval

Min Session Timeout

Enable session Audit.

VoipConfig.Pr ofileSetting. %d.Minse

SIP Ping Interval

Time interval to send SIP OPTIONS ping messages.

VoipConfig.Pr ofileSetting. %d.PingInterv al

RTP Bullet Interval

RTP keep alive packet, time between sending an empty packet to keep a port open.

VoipConfig.Pr ofileSetting. %d.RTPKeepAli veInterval

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

Digitmap

Define patterns of dial strings that the MTA can send to the SIP server when the pattern has been met, and not have to wait for the InterDigit Time out or the Critical Timeout. This helps improve call completion times.

VoipConfig.Pr ofileSetting. %d.Digitmap

Digitmap Timer

Critical Timeout

Short timeout if match digitmap .T pattern.

VoipConfig.Pr ofileSetting. %d.DMCriTimer

Inter Digit Timeout

Time to wait between digits being dialed before assuming no more entries are to be made. This is required to ensure a pause in dialing does not trigger an incomplete number to be sent to the SIP server.

VoipConfig.Pr ofileSetting. %d.DMParTime

Digitmap Action

Early Bailout

If a dialed number does not match any digitmap pattern, call a predefined bailout number. This number may be configured as an announcement to inform the user that this is an invalid number.

VoipConfig.Pr ofileSetting. %d.DMBailOutE nable

BailOut Number

The outgoing number when early bail out enabled.

VoipConfig.Pr ofileSetting. %d.DMBailOutN umber

4.1.5 DigitMap Setting

Digitmaps are templates that match different sequences of digits that users dial as part of their interaction with their phone system. After the user dials, when there is a match between the digits dialed and the digitmap, the MTA device sends the digits to the server to initiate the call. If there is no match, the system waits for the user to enter more digits or press the send key to indicate dialing is complete.

Load the SIP device with this digitmap pattern which corresponds to the dial plan selected by the service

operator. The digitmap is expressed in a format derived from the UNIX system command, “egrep.” You

must build the digit map based on the dialing plan which you wish to support.

Figure 18. DigitMap Setting

InnoMedia MTA8328-1U Administrative Guide

0

Local operator

00

Long distance operator

xxxx

Local extension number

8xxxxxxx

Local number

#xxxxxxx

Shortcut to local number at other corporate sites

*xx

Star services

91xxxxxxxxxx

Long distance number

9011 + up to 15 digits

International number

4.1.5.1 A Digitmap Example

The dial plan described above results in the following digit map:

(0| 00|[1-7]xxx|8xxxxxxx|#xxxxxxx|*xx|91xxxxxxxxxx|9011x.T)

4.1.5.2 Digitmap syntax

A DigitMap, according to this syntax, is defined either by a (case insensitive) “String” or by a “list of strings” over which the SIP Device will attempt to find a shortest possible match. Regardless of the above

syntax, a timer is currently only allowed if it appears in the last position in a string. Each string in the list is an alternate numbering scheme.

The formal syntax of the digit map is described by the following notation:

Digit ::= “0” | “1” | “2” | “3” | “4” | “5” | “6” | “7” | “8” | “9”

Timer ::= “T” | “t” -- matches the detection of a timer

Letter ::= Digit | Timer | “#” | “*” | “A” | “a” | “B” | “b” | “C” | “c” | “D” | “d”

Range ::= “X” | “x” -- matches any single digit

| “[“ Letters “]” -- matches any of the specified letters

Letters ::= Subrange | Subrange Letters

Subrange ::= Letter -- matches the specified letter

| Digit “-” Digit -- matches any digit between first and last

Position ::= Letter | Range

StringElement ::= Position -- matches an occurrence of the position

| Position “.” -- matches an arbitrary number of occurrences of the position, including 0

String ::= StringElement | StringElement String

StringList ::= String | String “|” StringList

DigitMap ::= String | “(“ StringList “)"

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

Basic Setting

Polarity Reversal

Enable Polarity Reversal – Tip and Ring are reversed when a call is answered.

VoipConfig.Pr ofileSetting. %d.PolarityRe versal

Max Flash Hook Timer

The maximum flash hook needs to last X ms before MTA treats it as a Flash Hook.

VoipConfig.Pr ofileSetting. %d.Flash_Time out

Min Flash Hook Timer

The minimum flash hook needs to last X ms before MTA treats it as a Flash Hook.

VoipConfig.Pr ofileSetting. %d.Flash_Min

Dtmf Level

The level of Dual Tone Multi Frequency tone.

VoipConfig.Pr ofileSetting. %d.DtmfLevel

4.1.5.3 FXS Setting

FXS port configuration allows you to set parameters based on the requirements of the telephony connections. You can alter the default settings and fine-tune the parameters for specific needs. For example, you might need to configure the ring timeout duration dependent on your needs. You can set the following configuration parameters for an FXS port:

Figure 19. FXS Setting

InnoMedia MTA8328-1U Administrative Guide

Tone Timer

Busy Tone Timeout

Busy Tone will play for xx seconds and then drop the call.

VoipConfig.Pr ofileSetting. %d.StopBusyTo ne

Delay Busy Tone

Play the Busy Tone when remote side hangs up, while the local side keeps the phone off hook.

VoipConfig.Pr ofileSetting. %d.DelayBusyT one

Warning Tone Timeout

When the remote side hangs up, after the busy tone time out, the device will start to play warning tone for this period of time.

VoipConfig.Pr ofileSetting. %d.StopWarnin gTone

Ring Timeout

Will ring a line for this period of time and then drop the call.

VoipConfig.Pr ofileSetting. %d.RingingTim eout

Dial Tone Timeout

Will play Dial Tone for this period of time and then play fast busy.

VoipConfig.Pr ofileSetting. %d.DialToneTi meout

OSI/PolarityRevers al Interval

When a call is terminated and OSI is enabled, Reverse Tip and Ring for X ms.

VoipConfig.Pr ofileSetting. %d.OsiTimer

Jitter Buffer

Jitter Buffer Mode

Fixed or adaptive jitter buffer support. Available Options:

 Adaptive – Jitter Buffer Size changes

during the call in response to network conditions.

 Fixed – Jitter Buffer Size stays at the

programmed value.

VoipConfig.Pr ofileSetting. %d.JBSetAdapt ive

Jitter Buffer Size

Available Options:

40, 60, 80, 100, 200, 300, 400, 500, 600 (ms)

VoipConfig.Pr ofileSetting. %d.JBSize

Adaptive Jitter Buffer

Max Jitter Buffer Size

The maximum Jitter Buffer Size that will be used in a call.

VoipConfig.Pr ofileSetting. %d.JBMaxSize

Target Jitter Buffer Size

If network conditions are good, and no late packets are detected, the jitter buffer will

VoipConfig.Pr ofileSetting.

InnoMedia MTA8328-1U Administrative Guide

continue to decrease until it meets the Target Jitter Buffer Size.

%d.JBAdaMinDe pth

Monitor Window

If during the defined window time frame, if 3 packets are late, the jitter buffer will be expanded.

VoipConfig.Pr ofileSetting. %d.JBAdaMonit or

Field Name

Description

Prov Tag

Feature Setting

Emergency Number

If the entered number is dialed, all call features are disabled. (Call Waiting, Call

Transfer, etc…)

VoipConfig.Pr ofileSetting. %d.EmergencyN um

Allow Bye at End of Emergency Call.

If enabled, when you hang up a call to an emergency number, we treat this as a normal call hang-up. If it is disabled, we will ring the phone when you hang-up instead of terminating the call.

VoipConfig.Pr ofileSetting. %d.EmgBye

Enable Caller ID of Emergency Call

If Caller ID is enabled, on an outbound call to the Emergency Number, Caller ID will be sent.

VoipConfig.Pr ofileSetting. %d.EmgCallerI D

4.1.6 Feature and Service Code Setting

Figure 20. Feature and Service Code Setting

InnoMedia MTA8328-1U Administrative Guide

Service Code

Cancel Call Waiting

The service code to cancel/resume receiving and answering an incoming call when this line is engaged.

VoipConfig.Pr ofileSetting. %d.CFStrCance lCW

InnoMedia MTA8328-1U Administrative Guide

Call Transfer

The service code to perform transferring the current call to another destination.

VoipConfig.Pr ofileSetting. %d.CFStrCXFR

Call ID Display

The service code to display the incoming caller phone number and its display name.

VoipConfig.Pr ofileSetting. %d.CFStrCIDDi splay

Call ID Block

The service code to hide the outbound caller phone number and its display name.

VoipConfig.Pr ofileSetting. %d.CFStrCIDBl ock

Call Parking

The service code to allow a person to put a call on hold at one phone set and continue the conversation from any other phone set.

VoipConfig.Pr ofileSetting. %d.CFStrCallP ark

Call Retrieve

The service code to allow a user to retrieve the parked call.

VoipConfig.Pr ofileSetting. %d.CFStrCallR etrieve

Do Not Disturb On

The service code of “Do Not Disturb-On,” preventing incoming calls from ringing the phone.

VoipConfig.Po fileSetting.% d.CFStrNoDist urbOn

Do Not Disturb Off

The service code of “Do Not Disturb-Off” allowing incoming calls to ring the phone.

VoipConfig.Pr ofileSetting. %d.CFStrNoDis turbOff

Play My IP Addr

When a phone is connected to the MTA, and this service code is dialed, the current IP address will be played out to the phone.

VoipConfig.Pr ofileSetting. %d.CFStrMyIP

Speed Dialing

Enter a prefix to use with the Speed Dialing Settings under the Port Config section. For example if you configure a #9 in this setting, to dial Speed Dialing Settings 0 phone number, you would simply dial a #90. Ensure the Prefix and Speed Dialing Settings don't cause a dialing conflict with other features such as Call Transfer and Call ID Display.

VoipConfig.Pr ofileSetting. X.CFStrSpeedD ial

Second Dial Tone Prefix

When the number entered is dialed, it will play secondary dial tone and the user is able to enter a regular number to dial out. Note: Number will be sent to the SIP server. eg. 9,(xxx)xxx-xxxx.

VoipConfig.Pr ofileSetting. %d.SecondDial toneNum

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

Basic Setting

Jitter Buffer Size

A jitter buffer temporarily stores arriving packets in order to minimize delay variations.

If a jitter buffer is too small, then an excessive number of fax packets may be discarded. If a jitter buffer is too large then it introduces additional delay.

VoipConfig.Pr ofileSetting. %d.FaxJitterB ufSize

Fax PTime

Available Options:

10, 20, 30, 40, 50, 60 (ms).

VoipConfig.Pr ofileSetting. %d.FaxPtime

Fax Answer Tone Trigger

When enabled the FAX receiving side will send FAX Re-Invite.

VoipConfig.Pr ofileSetting. %d.AnsToneTri ggerFlag

T38 Setting

Enable T38

Enable/Disable T.38 Fax feature.

VoipConfig.Pr ofileSetting. %d.T38Enable

4.1.7 Fax Setting

Configure the parameters for sending and receiving a fax over the VoIP channel. Two major approaches are adopted for fax over IP nowadays. Faxing involves two fax devices communicating generally for the purpose of passing one or more pages of image data from the sender to the receiver.

 G.711, sending fax signals in-band using the coding method of regular voice transmissions, or  T.38, a protocol that describes how to send a fax image data over the IP network. T38 is introduced

for more efficient and robust transmissions compared to use the same method as voice communications.

There are pros and cons of both approaches described above. Consult your service provider for appropriate configurations when needed.

Figure 21. Fax Setting

InnoMedia MTA8328-1U Administrative Guide

Add Click Add to create a new SIP User Account. Enter your SIP account Information at a minimum.

Save

Save the new profile.

Edit Edit the Profile created.

Delete

Delete the profile.

Field Name

Description

Prov Tag

Enable

Enable SIP User Account.

VoipConfig.Li neSetting.%d. LineEnable

Profile

Choose which Profile Name created under Profile Config should be used for this account.

VoipConfig.Li neSetting.%d. ProfileId

User ID

Account User ID/Name.

VoipConfig.Li neSetting.%d. UserID

Password

Account Password.

VoipConfig.Li neSetting.%d. UserPwd

4.2 Port Config

SIP Port Setting – List of current SIP user accounts. You may configure your user account on this device.

4.2.1 SIP Account Setting

Figure 22. SIP Account Setting

Figure 23. SIP Account Setting

InnoMedia MTA8328-1U Administrative Guide

Display Name

Name to be displayed for Caller ID.

VoipConfig.Li neSetting.%d. UserName

Authentication ID

Authentication ID if needed.

VoipConfig.Li neSetting.%d. UserAuth

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

Call Features

Call Waiting

To receive and answer an incoming call when this line is engaged in an active call.

VoipConfig.Li neSetting.%d. CallFeature.C allWaiting

Blind Transfer

Blind transfer is when a call is routed to a third party and the original call is ended without any check being made to determine whether the transferred call is answered or if the number is busy.

VoipConfig.Li neSetting.%d. CallFeature.B lindXfer

Consulted Transfer

Consulted Call Transfer is used for transferring a call to another destination without releasing the call from the voice platform until after the call is successfully transferred.

VoipConfig.Li neSetting.%d. CallFeature.C onsultXfer

Three Way Calls

3-Way Calling connects a third person to the current two-way conversation.

VoipConfig.Li neSetting.%d. CallFeature.T hreeWay

Caller ID display

Display of Caller ID (the caller phone number and display name).

VoipConfig.Li neSetting.%d. CallFeature.C ID

4.2.2 Features Setting

Figure 24. Call Feature Setting

InnoMedia MTA8328-1U Administrative Guide

Reject Anonymous Call

Rejection of Anonymous calls.

VoipConfig.Li neSetting.%d. CallFeature. RejectAnonymo us

Play VMWI

To enable/disable MTA to play voice mail waiting indicator.

VoipConfig.Li neSetting.%d. CallFeature.P layVMWI

Hot Phone

Enable Hot Phone

Hot Phone feature that automatically dials the Hot Phone Number when the phone is taken off hook.

VoipConfig.Li neSetting.%d. HotphoneEnabl e

Hot Phone Number

Enter the phone number that the MTA dials automatically when the phone is off hook.

VoipConfig.Li neSetting.%d. HotphoneNum

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

Voice Gain

Speaker Gain

Incoming volume control.

VoipConfig.Li neSetting.%d. RxVoiceVolume

Mic Gain

Outgoing volume control.

VoipConfig.Li neSetting.%d. TxVoiceVolume

Line Options

Line Start Mode

Available options:

 Loop Start  Ground Start

VoipConfig.Li neSetting.%d. LineStartMode

Silence Suppression

Not transmitting information when one of the parties involved in a call is not speaking.

Available options:

 Negotiated  Disabled

VoipConfig.Li neSetting.%d. SilenceSup

4.2.3 Line Setting

Line setting page includes input-MIC/output-speaker volume controls (gain controls), the designation of telephony current signal type (ground start or loop start) selection, and the way silence suppression is performed.

Figure 25. Line Setting

4.2.4 Speed Dial

Speed dial is a function to place a call by pressing a reduced number of keys. This function is particularly

useful for phone users who dial certain numbers on a regular basis.

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

Speed Dial Testing

1-9

VoipConfig.Li neSetting.%d. SpeedDialNum1

VoipConfig.Li neSetting.%d. SpeedDialNum2

…

VoipConfig.Li neSetting.%d. SpeedDialNum1 0

Figure 26. Speed Dial

4.3 Telephony Region and Misc Setting

4.3.1 Media Port Setting

Media port starting value should fall within the range from 10 to 65535 and should be an even number. Care should be taken as these settings can significantly impact voice performance or result in no voice paths if configured incorrectly. Consult your telephony service provider for configuration guidelines.

Figure 27. Media Port Setting

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

Media Port Start

The lowest RTP port number to be used when sending RTP traffic – It must be an even number.

VoipConfig.Vo ipSetting.Med iaPort

Media Port End

The highest RTP port number to be used when receiving RTP traffic – It must be an odd number.

VoipConfig.Vo ipSetting.Med iaPortEnd

Field Name

Description

Prov Tag

Line Impedance

The best match impedance for the voice port is the impedance setting that yields the highest value of Echo Return Loss.

VoipConfig.Re gionSetting.I mpedance

DC Current

The current on tip-ring, tip-to-ground and ring-to-ground.

VoipConfig.Re gionSetting.D CCurren

DC Ring Offset

The bias for ringing voltage. MTA uses this parameter only for balancing ringing.

VoipConfig.Re gionSetting.D COffset

4.3.2 Regional Setting

The MTA device connects your analog phone to its FXS (Foreign eXchange Subscriber interface). The FXS

port actually delivers the analog line to the subscriber. In other words it emulates the ‘plug on the wall’

that delivers a dial tone, battery current and ring voltage. FXS ports need to supply DC battery and AC ringing to enable the connected telephone equipment to transmit speech energy and to power the telephone equipment's ringing device.

These telephony parameters vary from country to country. When shipped from the factory, the MTA has set these parameters to match the necessary specifications. You can manually configure them if you want to override the default country values. (Notice: Incorrect input would result in poor voice quality or no signal.)

Figure 28. Regional Setting

InnoMedia MTA8328-1U Administrative Guide

DC Ring Voltage

In USA, the minimum ring voltage supplied is 40Vrms. The voltage at the subscribers end depends upon loop length and the number of ringers attached to the line.

VoipConfig.Re gionSetting.R ingVoltage

InnoMedia MTA8328-1U Administrative Guide

Ring Frequency

The telephone company sends a ringing signal which is an AC waveform. The frequency used in the United States is 20 HZ and in Europe is typically 25 Hz.

VoipConfig.Re gionSetting.R ingFreq

Ring Type

The shape of the ringing signal waveform.

VoipConfig.Re gionSetting.R ingType

CID Type

This parameter defines how CID / CLI signals are generated. Please note that only FSK based CID signals are supported. If your analog phone only supports DTMF CID, it will

not be able to display the CID of the caller.

VoipConfig.Re gionSetting.C IDType

4.3.3 Tone Cadence Setting

Configures the ring cadence (the timing of ringing to pause; it varies from country to country) for an FXS port. The normal ring cadence in North America is 2 seconds of ringing followed by 4 seconds of silence. The United Kingdom uses a double ring of 0.4 seconds separated by 0.2 seconds of silence, followed by 2 seconds of silence.

When shipped from the factory, the MTA has set the tone cadence to match the country requirements. You can manually set the tone cadence if you wish to override the default country values.

Figure 29. Tone Cadence Setting

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

Dial Tone

A dial tone is a telephony signal used to indicate that the telephone exchange is working.

VoipConfig.Re gionSetting.C adenceInfo.2. CadenceName

VoipConfig.Re gionSetting.C adenceInfo.2. CadenceConfig

Busy Tone

A busy signal indicates a failure to complete the requested call connection. Reasons could be:

 The called number is occupied, or  The other party has hung up at the end

of a call.

VoipConfig.Re gionSetting.C adenceInfo.1. CadenceName

VoipConfig.Re gionSetting.C adenceInfo.1. CadenceConfig

Ring back Tone

A ring back tone (or ringing tone) is heard by the caller while the phone they are calling is being rung.

VoipConfig.Re gionSetting.C adenceInfo.3. CadenceName

VoipConfig.Re gionSetting.C adenceInfo.3. CadenceConfig

Reorder Tone

Reorder tone, also known as fast busy tone, is the congestion tone or all trunks busy tone of a PSTN network. It varies from country to country.

VoipConfig.Re gionSetting.C adenceInfo.4. CadenceName

VoipConfig.Re gionSetting.C adenceInfo.4. CadenceConfig

Tone Cadence Setting (Format – freq1, freq2,vol,+[on1,off1,on2,off2,…])

InnoMedia MTA8328-1U Administrative Guide

Stutter Tone

A "stuttered" or interrupted dial tone is often used to indicate a calling feature such as call forwarding has been activated. (The voice mail waiting tone is represented by VMWI Tone below.)

VoipConfig.Re gionSetting.C adenceInfo.8. CadenceName

VoipConfig.Re gionSetting.C adenceInfo.8. CadenceConfig

VMWI Tone

Voice Mail Waiting Indication, indicating that voice mail is waiting.

VoipConfig.Re gionSetting.C adenceInfo.6. CadenceName

VoipConfig.Re gionSetting.C adenceInfo.6. CadenceConfig

Confirmation Tone

Confirmation Tone is used to acknowledge receipt for special services, such as:

 Speed calling, dial number has been

recorded.

 Call forwarding activation and de-

activation, etc.

VoipConfig.Re gionSetting.C adenceInfo.5. CadenceName

VoipConfig.Re gionSetting.C adenceInfo.5. CadenceConfig

Call Waiting Tone 1

VoipConfig.Re gionSetting.C adenceInfo.9. CadenceName

VoipConfig.Re gionSetting.C adenceInfo.9. CadenceConfig

InnoMedia MTA8328-1U Administrative Guide

Call Waiting Tone 2

VoipConfig.Re gionSetting.C adenceInfo.10 .CadenceName

VoipConfig.Re gionSetting.C adenceInfo.10 .CadenceConfi g

Call Waiting Tone 3

VoipConfig.Re gionSetting.C adenceInfo.11 .CadenceName

VoipConfig.Re gionSetting.C adenceInfo.11 .CadenceConfi g

Call Waiting Tone 4

VoipConfig.Re gionSetting.C adenceInfo.12 .CadenceName

VoipConfig.Re gionSetting.C adenceInfo.12 .CadenceConfi g

4.3.4 Ring Cadence Setting

For a telephone receiving an incoming call, the timing pattern of the incoming ring signal. This varies from country to country and may consist, for instance, of the ring voltage being applied for two seconds, followed by four seconds off, then back on for two seconds, and so on, until the phone is answered or the calling party hangs up, or a maximum number of rings is reached. Note that MTA8328 supports multiple ring cadence profiles for different countries.

When shipped from the factory, the MTA has set the ring cadence to match the country requirements. You can manually set the ring cadence if you wish to override the default country values.

Ring Cadence Setting (Format +[on1,off1,on2,off2,…])

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

Ring Cadence

For a telephone receiving an incoming call, the timing pattern of the incoming ring signal.

VoipConfig.Re gionSetting.C adenceInfo.13 .CadenceName

VoipConfig.Re gionSetting.C adenceInfo.13 .CadenceConfi g

Ring 1 Cadence

VoipConfig.Re gionSetting.C adenceInfo.14 .CadenceName

VoipConfig.Re gionSetting.C adenceInfo.14 .CadenceConfi g

Ring 2 Cadence

VoipConfig.Re gionSetting.C adenceInfo.15 .CadenceName

VoipConfig.Re gionSetting.C adenceInfo.15 .CadenceConfi g

Figure 30. Ring Cadence Setting

InnoMedia MTA8328-1U Administrative Guide

Ring 3 Cadence

VoipConfig.Re gionSetting.C adenceInfo.16 .CadenceName

VoipConfig.Re gionSetting.C adenceInfo.16 .CadenceConfi g

Ring 4 Cadence

VoipConfig.Re gionSetting.C adenceInfo.17 .CadenceName

VoipConfig.Re gionSetting.C adenceInfo.17 .CadenceConfi g

Ring 5 Cadence

VoipConfig.Re gionSetting.C adenceInfo.18 .CadenceName

VoipConfig.Re gionSetting.C adenceInfo.18 .CadenceConfi g

Splash Ring

A short ring to notify that some specified call features are processed. For instance, a short ring (splash tone) can notify each time a call is forwarded.

VoipConfig.Re gionSetting.C adenceInfo.19 .CadenceName

VoipConfig.Re gionSetting.C adenceInfo.19 .CadenceConfi g

4.4 Line Diagnostics

4.4.1 GR909 Test

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

GR909 Line Diagnostic Test

A suite of standards-based electrical tests which detect physical problems with the phone line.

FEMF/HAZ Test

This procedure tests for the hazardous electromotive force (HEMF) and foreign electromotive force (FEMF) between the TIP and RING leads. It reports a failure if the following limits are exceeded:

– Foreign DC HEMF limit = 135V. – Foreign AC HEMF limit = 50Vrms. – Foreign DC EMF limit = 6V. – Foreign AC EMF limit = 10Vrms.

Receiver Off-Hook Test

This procedure detects and reports a failure if an off-hook telephone is present.

REN Test

This procedure measures REN (Ringer Equivalence Number) loading by measuring the load impedance at 20 Hz. An REN loading of less than 0.175 REN or greater than 3 REN is reported as a failure.

Resistive Faults Test

This procedure measures TIP to RING onhook DC resistance. A DC resistance less than 150 k is reported as a failure.

Figure 31. GR909 Test

MTA8328-1U supports GR-909 test items which are based on a suite of standards based electrical tests.

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

Administrator Account Setting

This allows you to configure an Administrator ID and Password.

The default values are service provider dependent.

System.Accoun t.Admin.ID

System.Accoun t.Admin.Pass

Field Name

Description

Prov Tag

User Account Setting

This allows you to configure a user’s user ID and password.

The default values are service provider dependent.

System.Accoun t.User.ID

System.Accoun

t.User.Pass

5 System

5.1 Account Settings

5.1.1 Administrator Account Setting

Figure 32. Administrator account setting

5.1.2 User Account Setting

Figure 33. User Account Setting

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

Firmware Upload

Browse to a new firmware image file to upload to the unit.

Field Name

Description

Prov Tag

Reboot

Reboot opens a dialog box, and asks for

confirmation to “Reboot the System”.

5.2 Firmware Upload

5.3 Reboot

Figure 34. Firmware Upload

5.4 Restore To Factory

Figure 35. Reboot Dialog

Figure 36. Restore To Factory Dialog

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

Restore To Factory

Opens a dialog box, and asks for

confirmation to “Restore to Factory Default Values”.

The default values are service provider dependent.

Field Name

Description

Prov Tag

Restore User Setting

Opens a dialog box, and asks for confirmation to “Restore to User Setting”.

The default values are service provider dependent.

5.5 Restore User Setting

Figure 37. Restore User Setting

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

5.6 Page Permission

The administrator may specify which features are available for end subscribers to view (R) or configure (W).

Figure 38. User Page Permission Setting

InnoMedia MTA8328-1U Administrative Guide

User Page Permission Setting

Configure which pages the User Login can access and also if it can be used to write to the page.

N/A

Field Name

Description

Prov Tag

5.7 Provisioning Setting

5.7.1 Provision Server Setting

Provisioning Setting – Configure provisioning server and associated settings to this MTA device. Provisioning is a powerful feature that allows you to automatically configure the unit with all of its parameters. Therefore, if the unit is configured from the Factory with the desired Provisioning information, you will not need to manually configure the MTA with its SIP Profile and User Information, since the desired information can be entered into the Configuration File for that unit. Subsequently, when the device is powered on and obtains its IP address, it will go to the provisioning server and be configured.

Figure 39. Provisioning Server Setting

InnoMedia MTA8328-1U Administrative Guide

Enable Provisioning

Turns provisioning on/off.

System.Prov.E nable

Support DHCP Options

If enabled, the device will use the provisioning server IP (server option) and config file name (Bootfile option) from the DHCP options automatically.

System.Prov.D hcp-opt

Provisioning Server

IP or FQDN of the Provisioning Server.

System.Prov.S erver

Server Port

Port to be used to connect to the Provisioning Server. Port 8802 is

InnoMedia’s default port to connect to InnoMedia’s EMS Server, which handles

Provisioning and Management. However, any other port can also be used.

System.Prov.P ort

ConfigURL/Filename

Specify the config file to download.

System.Prov.U RL.Config

PostURL/Filename

Specify the path and filename for the MTA to upload the post-provisioning information to the server.

System.Prov.U RL.ProvPost

UserAgent Header

UserAgent Header sent out is modifiable.

Available parameters:

 Model name ($MOD)  MAC ($MAC)  Version ($VER)  Config file last loaded ($CFG)

Example Syntax: $MOD $MAC $VER $CFG.

Output: SIP User-Agent: MTA-8328-1U 001099112233 V1.0.0.0 /Provisioning/Config/xyz.cfg

System.Prov.U serAgent

User ID

The User ID for HTTP Digest Authentication.

System.Prov.A ccount.User

InnoMedia MTA8328-1U Administrative Guide

Password

The Password for HTTP Authentication.

System.Prov.A ccount.Passwo rd

Protocol

The Protocol to connect to the server. The supported protocols are: HTTP, HTTPS, FTP, and TFTP.

System.Prov.P rotocol

Format

Format of the config file to be sent to the MTA. Currently, the supported types are: INI and XML. In a future version, TLV (CableLabs PC2.0 standard) will be supported. INI is a TAG=VALUE style config file, XML is an XML formatted file.

System.Prov.F ormat

Encryption

The Encryption Format of the config file to be sent to the MTA. Supported formats are: Auto, None, RC4, AES, and AES-256.

System.Prov.E ncrypt

Encryption Key

The paraphrase to be used for encryption. Below is a table of the number of characters for each Encryption Type and Key Method.

RC4

AES

AES256

Hex

32

64

ASCII

16

32

Inno

Any

System.Prov.K ey

Key Method

Four methods are supported for the Key method: Inno Key, Raw Hex, ASCII String, and openSSL.

 Inno – InnoMedia hash key method.  Raw HEX – key is in binary form but

input as Hex String. Device will convert it back to binary as a decryption key.

 Raw Key – key is in ascii format already.

Device only uses it for the decryption key.

 OPENSSL key – Device will use

Encryption Key as password to generate openssl compatible key, salt and IV to decode the config file. Config file should be encrypted using the following command at the provisioning server: $ openssl enc –aes-256-cbc –k password –in infile –out outfile.

System.Prov.M ode

InnoMedia MTA8328-1U Administrative Guide

Re-Provisioning Interval

Time to next Re-Provision after a successful Provision.

System.Prov.R eprovInterval

Provisioning Fail Retry Interval

If a provision fails, how long the device waits before it tries again.

System.Prov.R etry-Interval

Provisioning Fail Retry Cap

There are 3 associated timers:

A provisioning successful timer: T1

A provisioning failed timer: T2

Maximum timer (Retry Cap): T3

If provisioning successful, following T1 interval to perform next provisioning.

If failed, following T2 interval of incremental factor to perform next provisioning.

If T2 eventually exceeds T3, then following T3 interval to perform next provisioning, until the system reboot OR provisioning successful.

System.Prov.R etry-Cap

Enable POST Provisioning

Post Message to be sent if enabled.

System.Prov.P ost

Enable Firmware Upgrade

When enabled, firmware will be downloaded when a new version is available. When disabled, firmware will not download even if a new version available.

System.Prov.S wUpgrade

5.8 EMS Setting

5.8.1 EMS Server

The InnoMedia EMS server is a powerful platform for service providers to be able to see Call Statistics, Voice Quality information, and to provide the ability to connect to devices behind NAT routers for diagnostics purposes.

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

Enable EMS

This enables the EMS feature.

System.EMS.En able

Device Type (0-

254)

This is the device type configured on the EMS Server, so that a user of the EMS server will see the device by name (such as 8328-1) in the device list. The type is also important for what options/features will be seen when a device is queried on the EMS.

System.EMS.De vType

EMS Server

The IP or FQDN address of the EMS Server and port. Default is to use port 5200 for connection to the server.

System.EMS.Se rver

Password

The password for EMS Server.

System.EMS.Pa ssword

Local EMS Port

The port number used at MTA device in order to connect to EMS server.

System.EMS.Po rt

Region ID

Region the device is assigned to. This is a number value that has to be entered, so a good example of region configuration might be based on Area Codes. Another example might be time zones. When the EMS Server is set up, careful consideration should be given to how the regions are defined.

System.EMS.De vRegion

Figure 40. Configuring EMS Server Information

InnoMedia MTA8328-1U Administrative Guide

Heartbeat type

The MTA will send a heartbeat to the EMS Server to let it know it is up and running. A Data Tunnel between the EMS and MTA is used, and this can be encrypted or not, depending on the Option type chosen. Below are the current Heartbeat types:

2 = Plain text tunnel formatted.

3 = Encrypted text – a shared secret key between the EMS and MTA must be configured on both the MTA and EMS.

System.EMS.HB _type

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

SNMP Manager

IP address of the SNMP Manager system.

System.SNMP.M anager

SNMP Community Name #1

Write

System.SNMP.P ublicCommunit yName

SNMP Community Name #2

Read and Write

System.SNMP.P rivateCommuni tyName

5.9 SNMP Setting

Configuring the SNMP server information for the MTA to send traps to or to get commands from the SNMP server.

Figure 41. SNMP Setting

5.10 Trace Log

5.10.1 Trace Log Setting

Configure the MTA device to display debugging messages according to the level parameters. Note: Trace

Level “LOG_DEBUG” will have performance impacts on the MTA device. It is recommended to use this

feature only when debugging is needed.

Figure 42. Trace Log Setting

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

Enable Trace Log

Enables the trace log.

Log.Enable

Trace Level

Follows RFC 5424 syslog message severities.

1 Alert: Action must be taken immediately

2 Critical: Critical conditions.

3 Error: Error conditions.

4 Warning: Warning conditions.

5 Notice: Normal but significant condition.

6 Informational: Informational messages.

7 Debug: Debug-level messages.

Additional Messages available. LOG_STACK -

- Network protocol related messages.

LOG_DQOS -- RTP traffic related messages.

Log.Level

Trace Channel

The Port you wish to monitor/debug. 0 covers all ports.

Log.Channel

Trace Verbose

Enable Trace logs to be displayed in a Telnet session.

Log.Verbose

Send to Syslog Server

When checked, will send out messages to a configured Syslog Server.

Log.Syslog.En able

Syslog Server

Syslog server IP address

Log.Syslog.Se rver

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

Telnet Access

Enable/Disable access and configure what port Telnet will be allowed in on.

System.ReLogi n.Telnet.WAN

System.ReLogi n.Telnet.Port

SSH Access

Enable/Disable access and configure what port SSH will be allowed in on.

System.ReLogi n.SSH.WAN

System.ReLogi n.SSH.Port

WEB Access

Enable/Disable access via HTTP or HTTPS and configure what ports will be used for each.

System.WEB.WA N

System.WEB.Po rt

System.WEB.Sp ort

5.11 Remote Access

5.11.1 Remote Access Setting

Configure the designated protocols and ports for a PC system to access the MTA device remotely.

Figure 43. Remote Access Setting

InnoMedia MTA8328-1U Administrative Guide

SNMP Access

Enable/Disable access and configure what port SNMP will be allowed in on.

System.SNMP.W AN

SNMP Port

The port to have the access of the SNMP.

System.SNMP.P ort

SNMP Trap Sink Port

The port which enables an agent to notify the EMS of significant events by sending unsolicited SNMP trap messages.

System.SNMP.T rapPort

Bonjour

Apple Macintosh Network Configuration Tool.

System.WEB.Bo njourWan

UPnP

A Microsoft basic internet device profile announcement.

System.WEB.UP NPWan

Field Name

Description

Prov Tag

Current Date

The current date, which you can modify.

Current Time

The current time, which you can modify.

Time Zone

The current Time Zone configured and you can modify with the pull down list. Note a reboot is needed for this setting to become effective.

System.Time.T imezone

Enable SNTP

Enable the SNTP service.

System.SNTP.E nable

5.12 System Time

5.12.1 Time Setting

Configure the SNTP time server IP/FQDN and time zone with which the MTA device synchronizes. Accurate time information is important for ensuring reliable telephony services.

Figure 44. Time Setting

InnoMedia MTA8328-1U Administrative Guide

SNTP Server #1, #2, and #3

FQDN or IP of SNTP time servers to sync up.

(Note: MTA8328-1U tries all the configured servers, calculates based on RFC 2030 and the delay. It then uses the lowest delay as the peer updates and sets the local time.)

System.SNTP.S erverList.%d. Server

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

IVR Language Setting

The language of IVR announcement.

N/A Field Name

Description

Prov Tag

Ping DNS Server

Check if the DNS server is reachable from the MTA device or not. Only the top three DNS servers on the priority server list will be checked.

System.Ping.T arget.DNS

Ping Gateway

Check if the default IP Gateway is reachable from the MTA device or not.

System.Ping.T arget.Gateway

Ping User Host

IP or FQDN to ping.

System.Ping.H ost

Ping Interval

How often device will send ping out. If 0, it is disabled.

System.Ping.I nterval

5.13 Language

The MTA device supports English, Spanish for Interactive Voice Response (IVR) services. Select the desired language for your needs.

Figure 45. Language Selection for IVR system

5.14 Ping Host

The MTA device will ping an IP address or FQDN to determine public IP connection. If no connection, the WAN LED will begin to blink fast.

Figure 46. Ping Host Setting

InnoMedia MTA8328-1U Administrative Guide

Field Name

Description

Prov Tag

System Config – Download

Downloads in a text file, the XML formatted file of the System Tab features.

N/A

System Config – Upload

You can upload an edited syscfg file to the MTA.

N/A

Network Config – Download

Downloads in a text file, the XML formatted file of the Network Tab features.

N/A

Network Config – Upload

You can upload an edited netcfg file to the MTA.

N/A

VoIP Config – Download

Downloads in a text file, the XML formatted file of the Telephony Tab features.

N/A

VoIP Config – Upload

You can upload an edited sipcfg file to the MTA.

N/A Field Name

Description

Prov Tag

5.15 Config File

5.15.1 System Config

System Config page allows you to

 Download configurations from the server and apply to the MTA.

OR

 Retrieve configurations from the MTA and upload to the server.

Figure 47. System Config

5.16 Certificate & Key

This page allows you to upload the encrypted keys or certificate for transporting signaling data through the secured TLS tunnel.

Figure 48. Certification & Key

InnoMedia MTA8328-1U Administrative Guide

CA Cert

Root certificate for verifying Server SIP TLS Certificate.

N/A Signing Cert

MTA Certificate for SIP TLS.

N/A

Signing Key

MTA Certificate private key, for encrypt/decrypt TLS data.

N/A

InnoMedia MTA8328-1U Administrative Guide

6 Troubleshooting

6.1.1 Telephone has no dial tone

Solution:

Ensure that all cables (PC USB, Telephone) are properly connected to the MTA (see Page 7).

Pick up telephone handset (phone off-hook), check for LED to be fast blinking Green. If not, please disconnect MTA power USB cable, and then reconnect it again.

If previous steps fail, report the failure to your VoIP service provider for attention.

InnoMedia MTA8328-1U Administrative Guide

Telephone Interface

1 FXS voice port

Network Interface

Micro USB port

Dimension

28.5mm in (H) x 58mm in (W) x 90mm in (D)

Power Supply

USB

Input: AC 100V~240V, 50Hz~60Hz, 200mA

Output : DC 5V, 1A

Power Consumption

Idle: 5V/0.22A(1.1W)

Talking: 5V/0.41A(2.1W)

Ringing (1REN): 5V/0.38A(1.9W)

Operating Temperature

32 ~ 122 ºF (0 ~ 50 ºC)

7 Hardware Specifications

InnoMedia MTA8328-1U Administrative Guide

LED STATES

Interfaces

Blinking State

MTA8328-1U Device State

PWR

Steady Green

The device power is on.

Off

The device power is off.

WAN

Solid Green

WAN 100BT link is active, device has IP address AND DNS resolution is successful.

Solid Yellow

WAN 10BT link is active, device has IP address AND DNS resolution is successful.

Off

WAN link is not connected. This is the same condition in which the "no WAN link" IVR is played.

Fast Blinking Green (0.25 sec. on, 0.25 sec. off)

WAN 100BT link is active but device is unable to get an IP address OR is unable to reach a public IP address. This is the same condition in which the “no internet connection” IVR is played.

Fast Blinking Yellow (0.25 sec. on, 0.25 sec. off)

WAN 10BT link is active but device is unable to get an IP address OR is unable to reach a public IP address. This is the same condition in which the "no Internet connection" IVR is played.

Medium-Slow Blinking Green (1 sec. on, 1 sec. off)

The device firmware is being upgraded. The PHONE LED blinks in unison with the WAN LED in this state.

PHONE

Off

The device has no power, OR

The device is powered on and initializing, OR

The device is being provisioned, OR

The device has initialized & been provisioned, but failed to register.

Steady Green

The device is registered and ready to make calls, and the telephone handset in on-hook. (not in use)

Slow Blinking Green (3 sec. on, 1 sec. off)

The device is registered and ready to make calls, and the telephone handset in on-hook (not in use), and there are new voicemail messages.

Medium-Fast Blinking Green (0.5 sec. on, 0.5 sec. off)

The device is registered and ready to make calls, and the telephone handset in off-hook (in use). Irrespective of voicemail state.

Appendix A1. LED States

InnoMedia MTA8328-1U Administrative Guide

LED STATES

Interfaces

Blinking State

MTA8328-1U Device State

Fast Blinking Red (0.25 sec. on, 0.25 sec. off)

One or more GR-909 tests failed. Irrespective of registration or voicemail state. This state is cleared when GR-909 tests are run again and all tests pass, or when the device is rebooted.

Medium-Slow Blinking Green (1 sec. on, 1 sec. off)

The device firmware is being upgraded. The PHONE LED blinks in unison with the WAN LED in this state.

InnoMedia MTA8328-1U Administrative Guide

NOTES for usage of variable %d:

1. The device allows up to 3 DDNS servers. With %d usage, the device can be configured to use

more than 1 DDNS services. Allowed range values are from 1, 2 or 3.

2. The device allows up to 3 DNS servers. With %d usage, the device can be configured to use more

than 1 DNS servers. Allowed range values are 1, 2, or 3.

3. The network parameter names starting with "Network.Interface.%d" allows defining the type of

network interface to use. The %d with value of 2 is defined for USB. Value 1 is reserved.

4. The line setting parameter names starting with "VoipConfig.LineSetting.%d” allows defining the

port the value will be set for. In a single port device, it will always be 1. For a two port device, the allowable values will be 1 or 2.

5. There are two %d variables for these parameters. The first %d defines the profile to use. There

are up to 4 profiles that can be configured with allowable values of 1 to 4. The second %d is for codec preference usage with allowable values of 1 through 6, where preference 1 is highest preference and 6 is lowest.

6. The profile setting parameter names starting with "VoipConfig.ProfileSetting.%d" allows defining

the profile that can be configured with allowable values of 1 to 4. Please ensure you have a "VoipConfig.ProfileSetting.%d.profileID" tag with a value of 1, included in your Provisioning Configuration even if you are using only one profile.

7. The device allows up to 3 SNTP servers. With %d usage, the device can be configured to use more

than 1 SNTP servers. Allowed range values are 1, 2, or 3.

Prov Tag

Allowable Values

Default Values

Note

Network.DDNS.%d.CheckInterval

1 to 20 minutes

15

1

Network.DDNS.%d.DomainName

String

Blank

1

Network.DDNS.%d.Enable

0=Disabled, 1=Enabled

0 - Disabled

1

Network.DDNS.%d.ForceInterval

1 to 7 days

3 1 Network.DDNS.%d.Password

String

Blank

1

Appendix A2. Default Values and Allowable Values

The table below provides details about provisioning parameter tags, their allowable values, and the

device default values. Since some of the parameters contain variables, they are represented by “%d”.

The Notes section below describes details of the various usages of this variable %d.

Note: Please refer to your appendix section for your factory default.

Network:

InnoMedia MTA8328-1U Administrative Guide

Network.DDNS.%d.ServiceProvider

String

changeip.com

1

Network.DDNS.%d.UserName

String

Blank

1

Prov Tag

Allowable Values

Default Values

Note

Network.DNS.%d.Server

IP Address

Blank

2 Prov Tag

Allowable Values

Default Values

Note

Network.Interface.%d.DSCP.Host

0-0xFF

0

3

Network.Interface.%d.DSCP.RTP

0-0xFF

0xB8

3

Network.Interface.%d.DSCP.Signal

0-0xFF

0x68

3

Prov Tag

Allowable Values

Default Values

Note

Network.Domain

String

Blank

Network.Hostname

String

Blank

Prov Tag

Allowable Values

Default Values

Note

Network.Interface.%d.Link.Mode

0-Auto 1-Half 2-Full

0 - Auto

3

Network.Interface.%d.Link.Speed

0-Auto 1-10 2-100

0 - Auto

3

Network.Interface.%d.Mac.EnableMacCloni ng

0=Disabled, 1=Enabled

0 - Disabled

3 Network.Interface.%d.Mac.MACClone

MAC Address

00:00:00:00:00:00

3

Network.Interface.%d.IPV4.DHCP

0=Disabled/Fixed 1=Enabled/DHCP

1 - Enabled

3 Network.Interface.%d.IPV4.Enable

0=Disabled, 1=Enabled

1 - Enabled

3

Network.Interface.%d.IPV4.Gateway

IP Address

255.255.255.255

3

Network.Interface.%d.IPV4.IPAddr

IP Address

255.255.255.255

3

Network.Interface.%d.IPV4.MTU

150<=val<=1500

1500

3

Network.Interface.%d.IPV4.NetMask

IP Address

255.255.255.255

3

Network.Interface.%d.PPPoE.Authenticatio n

PAP, CHAP

PAP

3 Network.Interface.%d.PPPoE.AutoConnect

0=Disabled, 1=Enabled

0 - Disabled

3

Network.Interface.%d.PPPoE.Enable

0=Disabled, 1=Enabled

0 - Disabled

3

Network.Interface.%d.PPPoE.IdleTimeout

0-65535

30

3

InnoMedia MTA8328-1U Administrative Guide

Network.Interface.%d.PPPoE.LcpEchoValue

0-256

0 3 Network.Interface.%d.PPPoE.MTU

Max 1500

1430

3

Network.Interface.%d.PPPoE.Server

String

Blank

3

Network.Interface.%d.PPPoE.User

String

Blank

3

Network.Interface.%d.PPPoE.Password

String

Blank

3

Network.Interface.%d.VLAN.Enable

0=Disabled, 1=Enabled

0 - Disabled

3

Network.Interface.%d.VLAN.Priority

0 - 7

0 3 Network.Interface.%d.VLAN.RtpPriority

0 - 7

0

3

Network.Interface.%d.VLAN.RtpVID

0-4095

0

3

Network.Interface.%d.VLAN.SigPriority

0 - 7

0

3

Network.Interface.%d.VLAN.SigVID

0-4095

0

3

Network.Interface.%d.VLAN.TosMap

0=Disabled, 1=Enabled

0 - Disabled

3

Network.Interface.%d.VLAN.VID

0-4095

0

3

InnoMedia MTA8328-1U Administrative Guide

Prov Tag

Allowable Values

Default Values

Note

VoipConfig.LineSetting.%d.CallFeature.Blind Xfer

0=Disabled, 1=Enabled

1 - Enabled

4

VoipConfig.LineSetting.%d.CallFeature.Call Waiting

0=Disabled, 1=Enabled

1 - Enabled

4 VoipConfig.LineSetting.%d.CallFeature.CID

0=Disabled, 1=Enabled

1 - Enabled

4

VoipConfig.LineSetting.%d.CallFeature.Cons ultXfer

0=Disabled, 1=Enabled

1 - Enabled

4

VoipConfig.LineSetting.%d.CallFeature.Play VMWI

0=Disabled, 1=Enabled

1 - Enabled

4

VoipConfig.LineSetting.%d.CallFeature.Reje ctAnonymous

0=Disabled, 1=Enabled

0 - Disabled

4

VoipConfig.LineSetting.%d.CallFeature.Thre eWay

0=Disabled, 1=Enabled

1 - Enabled

4 VoipConfig.LineSetting.%d.LineEnable

0=Disabled, 1=Enabled

0 - Disabled

4

VoipConfig.LineSetting.%d.HotphoneEnable

0=Disabled, 1=Enabled

0 - Disabled

4

VoipConfig.LineSetting.%d.HotphoneNum

String

Blank

4

VoipConfig.LineSetting.%d.LineStartMode

0=loop start, 1=grd start

0 4 VoipConfig.LineSetting.%d.ProfileId

0-3

Blank

4

VoipConfig.LineSetting.%d.RxVoiceVolume

-6 .. 6

0 4 VoipConfig.LineSetting.%d.SilenceSup

0=Disabled, 1=Enabled

0 - Disabled

4

VoipConfig.LineSetting.%d.SpeedDialNum1

Number

Blank

4

VoipConfig.LineSetting.%d.SpeedDialNum1 0

Number

Blank

4 VoipConfig.LineSetting.%d.SpeedDialNum2

Number

Blank

4

VoipConfig.LineSetting.%d.SpeedDialNum3

Number

Blank

4

VoipConfig.LineSetting.%d.SpeedDialNum4

Number

Blank

4

VoipConfig.LineSetting.%d.SpeedDialNum5

Number

Blank

4

VoipConfig.LineSetting.%d.SpeedDialNum6

Number

Blank

4

VoipConfig.LineSetting.%d.SpeedDialNum7

Number

Blank

4

VoipConfig.LineSetting.%d.SpeedDialNum8

Number

Blank

4

VoipConfig.LineSetting.%d.SpeedDialNum9

Number

Blank

4

VoipConfig.LineSetting.%d.TxVoiceVolume

-6 .. 6

0

4

Line Setting:

InnoMedia MTA8328-1U Administrative Guide

VoipConfig.LineSetting.%d.UserAuth

String

Blank

4

VoipConfig.LineSetting.%d.UserID

String

Blank

4

VoipConfig.LineSetting.%d.UserName

String

Blank

4

VoipConfig.LineSetting.%d.UserPwd

String

Blank

4

InnoMedia MTA8328-1U Administrative Guide

Prov Tag

Allowable Values

Default Values

Note

VoipConfig.ProfileSetting.%d.AnsToneTrigg erFlag

0=Disabled, 1=Enabled

0 - Disabled

5 VoipConfig.ProfileSetting.%d.BulletInterval

0 - 65535

0 - Disabled

5

VoipConfig.ProfileSetting.%d.CFStrCallPark

Number

*98

5

VoipConfig.ProfileSetting.%d.CFStrCallRetri eve

Number

*99

5

VoipConfig.ProfileSetting.%d.CFStrCancelC W

Number

*70

5 VoipConfig.ProfileSetting.%d.CFStrCIDBlock

Number

*67

5

VoipConfig.ProfileSetting.%d.CFStrCIDDispl ay

Number

*82

5 VoipConfig.ProfileSetting.%d.CFStrCXFR

Number

*90

5

VoipConfig.ProfileSetting.%d.CFStrNoDistur bOff

Number

#74#

5

VoipConfig.ProfileSetting.%d.CFStrNoDistur bOn

Number

*74#

5 VoipConfig.ProfileSetting.%d.CFStrMyIP

Number

***1

5

VoipConfig.ProfileSetting.%d.CFStrSpeedDi al

Number

*75

5

VoipConfig.ProfileSetting.%d.Codecs.%d.Co decId

0,2,4,8,18,104

0,8

5

VoipConfig.ProfileSetting.%d.Codecs.%d.Na me

PCMU,PCMA,iLBC,G729, G726-32,G723

PCMU,PCMA

5

VoipConfig.ProfileSetting.%d.Codecs.%d.Op tions

Depend on codec

5

VoipConfig.ProfileSetting.%d.Codecs.%d.Pa yload

PCMU = 0, PCMA = 8, G729 = 18, iLBC = 104, G726-32 = 2, G723 = 4

5 VoipConfig.ProfileSetting.%d.Codecs.%d.PTi me

10,20,30,40,50,60

20

5

Profile Setting:

InnoMedia MTA8328-1U Administrative Guide

Prov Tag

Allowable Values

Default Values

Note

VoipConfig.ProfileSetting.%d.DelayBusyTon e

0-65535

3

6

VoipConfig.ProfileSetting.%d.DialToneTime out

0-65535

16

6 VoipConfig.ProfileSetting.%d.Digitmap

Digitmap

Blank

6

VoipConfig.ProfileSetting.%d.DMBailOutEn able

0=Disabled, 1=Enabled

0 - Disabled

6

VoipConfig.ProfileSetting.%d.DMBailOutNu mber

String

Blank

6 VoipConfig.ProfileSetting.%d.DMCriTimer

0-255

4

6

VoipConfig.ProfileSetting.%d.DMParTime

0-255

16 6 VoipConfig.ProfileSetting.%d.DtmfLevel

0 - -10

-5

6

VoipConfig.ProfileSetting.%d.EmergencyNu m

Number

911

6 VoipConfig.ProfileSetting.%d.EmgBye

0=Disabled, 1=Enabled

0 - Disabled

6

VoipConfig.ProfileSetting.%d.EmgCallerID

0=Disabled, 1=Enabled

0 - Disabled

6

VoipConfig.ProfileSetting.%d.ExpoBackoff

10 - 5000

500 6 VoipConfig.ProfileSetting.%d.ExpoCap

1 - 32000

2000

6

VoipConfig.ProfileSetting.%d.FaxJitterBufSiz e

0 - 240

160

6 VoipConfig.ProfileSetting.%d.FaxPtime

10,20,30

20 6 VoipConfig.ProfileSetting.%d.Flash_Min

130 - Flash_Timeout

300

6

VoipConfig.ProfileSetting.%d.Flash_Timeou t

130 - 1800

900

6 VoipConfig.ProfileSetting.%d.InviteRetry

0 - 7

4 6 VoipConfig.ProfileSetting.%d.JBSetAdaptive

1=Adaptive, 2=Fixed

1 - Adaptive

6

VoipConfig.ProfileSetting.%d.JBAdaMinDep th

20-3000

60

6 VoipConfig.ProfileSetting.%d.JBAdaMonitor

10-3000

3000

6

VoipConfig.ProfileSetting.%d.JBMaxSize

40-1000

1000

6

VoipConfig.ProfileSetting.%d.JBSize

1-600

60 6 VoipConfig.ProfileSetting.%d.LocalPort

1-65535

5060

6

VoipConfig.ProfileSetting.%d.Minse

0 - 2100000000

0

6

InnoMedia MTA8328-1U Administrative Guide

VoipConfig.ProfileSetting.%d.NoRport

0=Disabled, 1=Enabled

0 - Disabled

6

VoipConfig.ProfileSetting.%d.NonInviteRetr y

0 - 10

4

6 VoipConfig.ProfileSetting.%d.NotifyFlash

0=Disabled, 1=Enabled

0 - Disabled

6

VoipConfig.ProfileSetting.%d.NumCodecs

1-6 2 6

VoipConfig.ProfileSetting.%d.OsiTimer

0 - 65535

900ms

6

VoipConfig.ProfileSetting.%d.OutboundPro xy

0=Disabled, 1=Enabled

0 - Disabled

6 VoipConfig.ProfileSetting.%d.PingInterval

0 - 2100000000

0

6

VoipConfig.ProfileSetting.%d.PolarityRevers al

0=OSI 1=PR

0

6

VoipConfig.ProfileSetting.%d.PoundCharact er

0=Disabled, 1=Enabled

0 - Disabled

6 Prov Tag

Allowable Values

Default Values

Note

VoipConfig.ProfileSetting.%d.profileID

0 - 3

0

6

VoipConfig.ProfileSetting.%d.ProfileName

String

Profile_1

6

VoipConfig.ProfileSetting.%d.RegCredential

0=Disabled, 1=Enabled

0

6

VoipConfig.ProfileSetting.%d.RegInterval

0 - 12000

3600

6

VoipConfig.ProfileSetting.%d.RegRetryResp

0 - 65535

Blank

6

VoipConfig.ProfileSetting.%d.RegRetryTime

0 - 65535

30

6

VoipConfig.ProfileSetting.%d.Rfc2833DTMF

0=off, 1=always, 2=nego

2 6 VoipConfig.ProfileSetting.%d.Rfc2833Type

93 - 254

101

6

VoipConfig.ProfileSetting.%d.RingingTimeo ut

0 - 65535

180

6

VoipConfig.ProfileSetting.%d.RTPKeepAliveI nterval

0-65535

0

6

VoipConfig.ProfileSetting.%d.SecondDialton eNum

0 - 9 # or *

Blank

6 VoipConfig.ProfileSetting.%d.ShortHeader

0=Disabled, 1=Enabled

0 - Disabled

6

VoipConfig.ProfileSetting.%d.SipDomain

IP or FQDN

Blank

6

VoipConfig.ProfileSetting.%d.SipInfoFlash

0=Disabled, 1=Enabled

0 - Disabled

6

VoipConfig.ProfileSetting.%d.SipPAccessInf o

String

Blank

6

InnoMedia MTA8328-1U Administrative Guide

VoipConfig.ProfileSetting.%d.SipPingProxy

IP or FQDN

Blank

6

VoipConfig.ProfileSetting.%d.SIPProxy

IP or FQDN

Blank

6

VoipConfig.ProfileSetting.%d.SipRsync

0=Disabled, 1=Enabled

1 - Enabled

6

InnoMedia MTA8328-1U Administrative Guide

VoipConfig.ProfileSetting.%d.SipSupport10 0rel

0=Disabled, 1=Enabled

0 - Disabled

6 VoipConfig.ProfileSetting.%d.SipZeroIpHold

0=Disabled, 1=Enabled

0 - Disabled

6

VoipConfig.ProfileSetting.%d.StopBusyTone

0 - 65535

30

6

VoipConfig.ProfileSetting.%d.StopWarningT one

0 - 65535

30

6 VoipConfig.ProfileSetting.%d.T38Enable

0=Disabled, 1=Enabled

0 - Disabled

6

VoipConfig.ProfileSetting.%d.ThreeWayEnd Refer

0=Disabled, 1=Enabled

1 - Enabled

6 VoipConfig.ProfileSetting.%d.TrustedProxy

0=Disabled, 1=Enabled

0 - Disabled

6

VoipConfig.ProfileSetting.%d.UseSipDTMF

0=Disabled, 1=Enabled

0 - Disabled

6

VoipConfig.ProfileSetting.%d.UseUAHeader

0=Disabled, 1=Enabled

1 - Enabled

6

VoipConfig.ProfileSetting.%d.UserAgent

String

Empty

6

Prov Tag

Allowable Values

Default Values

Note

VoipConfig.RegionSetting.CadenceInfo.1.Ca denceConfig

Cadence

480,620,24,+[500,500]

VoipConfig.RegionSetting.CadenceInfo.1.Ca denceName

Cadence

Busy

VoipConfig.RegionSetting.CadenceInfo.2.Ca denceConfig

Cadence

350,440,13,+[65535]

VoipConfig.RegionSetting.CadenceInfo.2.Ca denceName

Cadence

Dial

VoipConfig.RegionSetting.CadenceInfo.3.Ca denceConfig

Cadence

440,480,19,+[2000,4000]

VoipConfig.RegionSetting.CadenceInfo.3.Ca denceName

Cadence

Ringback

VoipConfig.RegionSetting.CadenceInfo.4.Ca denceConfig

Cadence

480,620,24,+[250,250]

VoipConfig.RegionSetting.CadenceInfo.4.Ca denceName

Cadence

Reorder

VoipConfig.RegionSetting.CadenceInfo.5.Ca denceConfig

Cadence

350,440,13,[100,100,300]

VoipConfig.RegionSetting.CadenceInfo.5.Ca denceName

Cadence

Confirm

Region Setting:

InnoMedia MTA8328-1U Administrative Guide

VoipConfig.RegionSetting.CadenceInfo.6.Ca denceConfig

Cadence

350,440,13,[100,100,100,100 ,100,100,100,100,65 535]

VoipConfig.RegionSetting.CadenceInfo.6.Ca denceName

Cadence

vmwi

VoipConfig.RegionSetting.CadenceInfo.8.Ca denceConfig

Cadence

350,440,13,[250,250,250,250 ,250,250,65535]

VoipConfig.RegionSetting.CadenceInfo.8.Ca denceName

Cadence

Stutter

VoipConfig.RegionSetting.CadenceInfo.9.Ca denceConfig

Cadence

440,0,13,+[300,9700]

VoipConfig.RegionSetting.CadenceInfo.9.Ca denceName

Cadence

cwt-1

VoipConfig.RegionSetting.CadenceInfo.10.C adenceConfig

Cadence

440,0,13,+[100,100,100,97 00]

VoipConfig.RegionSetting.CadenceInfo.10.C adenceName

Cadence

cwt-2

VoipConfig.RegionSetting.CadenceInfo.11.C adenceConfig

Cadence

440,0,13,+[100,100,100,10 0,100,9700]

InnoMedia MTA8328-1U Administrative Guide

VoipConfig.RegionSetting.CadenceInfo.11.C adenceName

Cadence

cwt-3

VoipConfig.RegionSetting.CadenceInfo.12.C adenceConfig

Cadence

440,0,13,[100,100,300,1 00]

VoipConfig.RegionSetting.CadenceInfo.12.C adenceName

Cadence

cwt-4

VoipConfig.RegionSetting.CadenceInfo.13.C adenceConfig

Cadence

440,480,0,+[2000, 4000]

VoipConfig.RegionSetting.CadenceInfo.13.C adenceName

Cadence

Ring

VoipConfig.RegionSetting.CadenceInfo.14.C adenceConfig

Cadence

+[2000,4000]

VoipConfig.RegionSetting.CadenceInfo.14.C adenceName

Cadence

Ring1

VoipConfig.RegionSetting.CadenceInfo.15.C adenceConfig

Cadence

+[800,400,800,40 00]

VoipConfig.RegionSetting.CadenceInfo.15.C adenceName

Cadence

Ring2

VoipConfig.RegionSetting.CadenceInfo.16.C adenceConfig

Cadence

+[400,200,400,20 0,800,4000]

VoipConfig.RegionSetting.CadenceInfo.16.C adenceName

Cadence

Ring3

VoipConfig.RegionSetting.CadenceInfo.17.C adenceConfig

Cadence

+[300,200,1000,2 00,300,4000]

VoipConfig.RegionSetting.CadenceInfo.17.C adenceName

Cadence

Ring4

VoipConfig.RegionSetting.CadenceInfo.18.C adenceConfig

Cadence

[500]

VoipConfig.RegionSetting.CadenceInfo.18.C adenceName

Cadence

Ring5

InnoMedia MTA8328-1U Administrative Guide

VoipConfig.RegionSetting.CadenceInfo.19.C adenceConfig

Cadence

[500]

VoipConfig.RegionSetting.CadenceInfo.19.C adenceName

Cadence

Splash VoipConfig.RegionSetting.CIDType

FSK

VoipConfig.RegionSetting.DCCurren

20, 30, 40 mA

20 VoipConfig.RegionSetting.DCOffset

0 -20 V

0 VoipConfig.RegionSetting.Impedance

600, 900 ohm

600 VoipConfig.RegionSetting.RingFreq

20, 25 Hz

20 VoipConfig.RegionSetting.RingType

Sinusoidal,Trapazodial

Sinusoidal

VoipConfig.RegionSetting.RingVoltage

53, 51, 45 Vrms

53

Prov Tag

Allowable Values

Default Values

Note

System.Account.Admin.ID

String

admin

System.Account.Admin.Pass

String

password

System.Account.User.ID

String

user System.Account.User.Pass

String

welcome

Prov Tag

Allowable Values

Default Values

Note

System.EMS.DevRegion

0-65535

1 System.EMS.DevType

1-65535

10

System.EMS.Enable

Enable/Disable

0 - Disabled

System.EMS.HB_type

type 2, type3

2 System.EMS.Password

String

Blank

System.EMS.Port

1-65535

5200

System.EMS.Server

String

Blank

Prov Tag

Allowable Values

Default Values

Note

System.Language.IVR_Language

0 - English 1-Spanish

0-English

System:

InnoMedia MTA8328-1U Administrative Guide

Prov Tag

Allowable Values

Default Values

Note

System.MasterDNS.%d.Server

String

Blank

3 Prov Tag

Allowable Values

Default Values

Note

System.Ping.Host

ip or FQDN

Blank

System.Ping.Interval

0 - 65535

Blank - 0

System.Ping.Target.DNS

0=Disabled, 1=Enabled

1 - Enabled

System.Ping.Target.Gateway

0=Disabled, 1=Enabled

0 - Disabled

Prov Tag

Allowable Values

Default Values

Note

System.Prov.Account.Password

String

Blank

System.Prov.Account.User

String

Blank

System.Prov.Dhcp-opt

0=Disabled, 1=Enabled

0 - Disabled

System.Prov.Enable

0=Disabled, 1=Enabled

0 - Disabled

System.Prov.Encrypt

0: Auto 1:None 2:RC4 3:AES 4:AES256

0 System.Prov.Format

0: INI 1:XML

0 System.Prov.Key

String

Blank

System.Prov.Mode

0: Inno -- InnoMedia Key Algo 1:Raw Hex - HEX String key 2:Raw String - ASCII String key 3:OpenSSL

0

System.Prov.Port

1-65535

8802

System.Prov.Post

0=Disabled, 1=Enabled

0 - Disabled

System.Prov.Protocol

0: HTTP 1:HTTPS 2:FTP 3:TFTP

0 System.Prov.Server

String

Blank

System.Prov.Reprov-Interval

1 -210000000

86400 sec.

System.Prov.Retry-Cap

1 -210000000

1800 sec.

System.Prov.Retry-Interval

0 - 210000000

120 sec.

System.Prov.SwUpgrade

0=Disabled, 1=Enabled

0 - Disabled

InnoMedia MTA8328-1U Administrative Guide

System.Prov.URL.Config

String

Blank

System.Prov.URL.ProvPost

String

Blank

System.Prov.UserAgent

String

Empty

Prov Tag

Allowable Values

Default Values

Note

System.SNMP.Manager

String

127.0.0.1

System.SNMP.Port

1-65535

161 System.SNMP.PrivateCommunityName

String

Private

System.SNMP.PublicCommunityName

String

Public

System.SNMP.TrapPort

10 - 65535

162

System.SNMP.WAN

0=Disabled, 1=Enabled

1 - Enabled

Prov Tag

Allowable Values

Default Values

Note

System.SNTP.Enable

0=Disabled, 1=Enabled

1 - Enabled

System.SNTP.ServerList.%d.Server

String

us.pool.ntp.org

7

System.Time.Timezone

(GMT+9) Adelaide (GMT+1) Amsterdam, Netherlands (GMT-3) Argentina (GMT+2) Athens, Greece (GMT-4) Atlantic Time (GMT+12)Auckland, Wellington (GMT+1) Barcelona, Spain (GMT+1) Berlin, Germany (GMT-3) Brazil, San Paulo (GMT+10)Brisbane (GMT+1) Brussels, Belgium (GMT+1) Budapest, Hungary (GMT-6) Central America (GMT+8) China Time (GMT+1) Copenhagen, Denmark

US Pacific Time

(GMT+9:30)Darwin (GMT+0) Dublin, Ireland

InnoMedia MTA8328-1U Administrative Guide

(GMT+12)Fiji Time (GMT+1) Geneva, Switzerland (GMT+2) Helsinki, Finland (GMT+10)Hobart (GMT+7) Jakarta (GMT+9) Japan Time (GMT+9) Korea Time (GMT+2) Kyiv, Ukraine (GMT+0) Lisbon, Portugal (GMT+0) London, Great Britain (GMT+1) Madrid, Spain (GMT+3) Moscow, Russia (GMT+5:45)Nepal Time (GMT-12)New Zealand Time (GMT3:30)Newfoundland Time (GMT+1) Oslo, Norway

(GMT-8) US Alaska Time (GMT-5) US Eastern Time (GMT-6) US Central Time (GMT-7) US Mountain Time (GMT-8) US Pacific Time (GMT-10)USHawaii Time (GMT+1) Paris, France (GMT+8) Perth (GMT+1) Prague, Czech Republic (GMT+1) Roma, Italy (GMT+8) Singapore (GMT+5:30)Sri Lanka Time (GMT+3) St.Petersburg, Russia (GMT+1) Stockholm, Sweden (GMT+10)Sydney (GMT-10)Tahiti Time (GMT+8) Taiwan Time (GMT+8) Tallinn, Estonia (GMT+8) Ulaanbaatar,

InnoMedia MTA8328-1U Administrative Guide

Mongolia

Prov Tag

Allowable Values

Default Values

Note

System.ReLogin.SSH.Port

1-65535

22 System.ReLogin.SSH.WAN

0=Disabled, 1=Enabled

0 - Disabled

System.ReLogin.Telnet.Port

1-65535

23 System.ReLogin.Telnet.WAN

1

0 - Disabled

System.WEB.BonjourWan

0=Disabled, 1=Enabled

0 - Disabled

System.WEB.Port

1-65535

80 System.WEB.SPort

1-65535

8080

System.WEB.UPNPWan

0=Disabled, 1=Enabled

0 - Disabled

System.WEB.WAN

0=Disabled, 1=Enabled

1-Enabled

Prov Tag

Allowable Values

Default Values

Note

Log.Channel

Port number from 1

0 Log.Enable

Enabled/Disable

0 - Disabled

Log.Level

1 .. 7

3-LOG_ERR

Log.Verbose

Enabled/Disable

0 - Disabled

Log.Syslog.Enable

Enabled/Disable

0 - Disabled

Log.Syslog.Server

URL

Blank

Prov Tag

Allowable Values

Default Values

Note

VoipConfig.VoipSetting.MediaPort

2-65532

10000

VoipConfig.VoipSetting.MediaPortEnd

5-65535

10011

Miscellaneous Setting:

InnoMedia MTA8328-1U Administrator's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual