InnoMax Heater Low Watt User Manual

This is your Thermal Guardian 5 years limited warranty. In the event that service resulting from a manufacturing defect is
required during the first two years after the original purchase, your Thermal Guardian Model TOUCH TEMP, QUANTUM Heater
will be fully repaired or replaced at our option, at no charge to the purchaser except for freight cost.

THIS LIMITED WARRANTY SUPERSEDES ANY OTHER WARRANTY PACKAGED OR

MADE AVAILABLE WITH THIS PRODUCT

IMPORTANT !

Warranty periods

Years 1-2 fully repaired or replaced.............................No Charge

Years 3-5 prorated cost to replace........65% of Manufacturer Suggested Retail Price

*We reserve the right of substitute materials or models of comparable or greater quality.

If there is a defect in manufacturing which requires service during the first two years

WHAT SERVIC E CAN I EXPE CT?

after the original purchase, your Thermal Guardian Heater will be fully repaired or replaced at our option without charge except freight costs.

There will be a period of additional warranty for three more years, this added period, will cover only 35% of retail suggested cost at time of return.
Freight cost will be also charged.

Contact your Thermal Guardian dealer for prompt service, for warranty returns sufficient

HOW DO I GET SERVICE?

proof of date and place of purchase is required to validate any warranty service available. Trade name and manufacturing date
must be intact to properly identify the unit as qualifying for warranty service. As it is necessary to keep your original sales receipt,
it might be a good idea to keep a copy of your original sales slip or invoice with your installation and instruction manual.

. ..... 1

WHAT DOES MY LIMITED WARRAN TY COVER?

The quality and pride that is crafted into every Thermal
Guardian Waterbed Heater, enables us to offer to the original purchaser only, who uses this heater solely for home waterbed
use, a limited five years warranty covering any manufacturing defect in workmanship or material. (See warranty periods

table above)

HOW LONG IS THE WARRANTY PERIOD?

The warranty coverage runs 5 years from the date of purchase.
Repair or replacement of a component does not extend this warranty or begin a new warranty. (See warranty periods table

above)

• PLEASE PAY CAREFUL ATTENTION TO THE FACT THAT FAILURE AND DAMAGE CAN EASILY
OCCUR IF FOREIGN OBJECTS ON TOP OF OR UNDER THE HEATER AND BETWEEN THE HEATER
AND MATTRESS IMPEDE THE TRANSFER OF HEAT FROM THE HEATER PAD TO THE MATTRESS
OR IF THE HEATER IS PLUGGED IN AND OPERATING WHEN THE MATTRESS IS NOT
COMPLETELY FULL.

• KEEP CONTROL UNPLUGGED FROM POWER OUTLET AND HEATER PAD UNTIL THE MATTRESS
IS FILLED.

• UNPLUG THE HEATER BEFORE DRAINING.

• THE HEATER MUST BE ON A FLAT SMOOTH SUPPORTING SURFACE.

NEVER USE THE HEATER IN ANY APPLICATION WHERE A HUMAN BODY CAN TOUCH THE
SURFACE OF THE HEATER BECAUSE OF IMPROPER MATTRESS SELECTION, UNDER FILLING,
OBESITY OR ANY OTHER REASONS, PARAPLEGICS OR ANY OTHER PERSONS WITH SENSORY
PROBLEMS SHOULD PAY PARTICULAR ATTENTION TO THIS SECTION, AS SHOULD PERSONS
SELECTING PRODUCTS FOR PERSONS WITH THESE OR SIMILAR IMPAIRMENTS.

NO WARRANTY OR REPRESENTATION IS MADE FOR THE PRODUCT’S SUITABILITY FOR
ANY PERSON’S MEDICAL CONDITION OR PROBLEM.

We know you will be pleased with your selection of your new Thermal Guardian Softside Waterbed Heater. Rest well

and rest assured that you have selected the finest in heating system, which will afford years of sleeping comfort.

.

.

.
.
.

A R E T H E R E E XC L U S I O N S ?

Yes, this limited warranty does not apply to any damage, caused by improper use,
negligence, improper installation, acts of God or failures caused by extreme temperatures or unusual conditions.

THI S LIMITED WARRAN TY IS LIMI TED TO REPAIR OR RE PLACEMENT OF THE THERMAL GUARDIAN WATERBED HEATER
AT OUR OPTIO N AND ANY DAMAGES DUE TO CO NSEQUENTIAL LO SSES OF ANY NATURE ARE EXP RESSLY EXCLUDED.

We shall not be liable for consequential damages (any cost of repairing other property which is damaged through the use of this
product) or incidental damages (loss of use, loss of time, miscellaneous charges or other damages).

This limited Warranty shall be void unless the waterbed heater is used in

IMPORTANT WARRANTY INFORMATION:

accordance with the instructions in our Instruction Manual and on the heater pad, and in conjunction with a confining frame and
waterbed mattress of a correct size and safety liner capable of capturing the entire liquid contents of the mattress should a failure occur.

This prorated warranty is limited only to the original buyer from an authorized Thermal Guardian Dealer and is
not transferable to subsequent owners of the product.

NO WAR RANT I ES, E X PRESS OR IMP L I ED, ARE EXTE NDED TO PER S ONS WHO PU RCHAS E TH E

PRODUCT FROM OTHER THAN AUTHORIZED THERMAL GUARDIAN DEALERS.

ALL WARR ANTI ES INCLU DING THE IMPLI ED WARR ANTI ES OF MERCH ANTABI LITY AND FI TNESS

ARE HEREBY EXCLUDED. ANY AND ALL IMPLIED WARRANTIES OTHER THAN THOSE WARRANTIES THAT

M AY N O T B E E XC L U D E D U N D E R A NY AP P L I C AB L E L AW A R E E X P R E S SLY E X CL U D E D .

T H I S I S T H E E X C L U S I V E WA R R A N T Y F O R T H E T H E R M A L G U A R D I A N A N D A N Y

OTHER STATEMENTS OR EXPRESS OR IMPLIED WARRANTIES ARE EXPRESSLY DENIED.

CERTIFIED TO THE

STANDARDS OF

14451445

QUANTUM

TOUCH TEMP

20019552001955

THERMAL GUARDIAN

TEMPERATURE CONTROL SYSTEMSTEMPERATURE CONTROL SYSTEMS

PROTECTED WITH A THERMAL SAFETY FUSE

Waterbed Heater For Tube Type and Softside Fluid Support
Sleep Systems with a Minimum Water Fill Level of 3 Inches

.

SOFTSIDE AND TUBE TYPE

WATERBED HEATER

WARRANTY AND

INSTALLATION INSTRUCTION

YOU MAY HAVE OTHER RIGHTS:

Some states do not allow the exclusion or limitation of incidental or consequential
damages. This warranty gives you specific right and you may have other rights which vary from state to state. The duration of any applicable
implied warranties shall not exceed in duration the terms of this limited warranty. Some states do not allow limitations on how long and implied
warranty lasts, so the above limitation may not apply to you.

9504-19QT-LW01

MANUAL

- IMPORTANT TO SAVE THESE INSTRUCTIONS -

CAUTION

DO NOT depress the waterbag in the area over the heater to the extent that the top surface of

the mattress contacts the bottom. This may cause damage to the mattress and / or heater

DO NOT place heater pad over unfilled knotholes or on cracks in the base platform.

For use with minimum 3” fill softside flotation systems and tube type beds.

IF THESE OCCUR YOU WILL VOID THE WARRANTY !

SAVE THESE INSTRUCTIONS.

WATER MATTRESS CHAMBER(S)WATER MATTRESS CHAMBER(S)WATER MATTRESS CHAMBER(S)

SAFETY LINER

SOFTSIDE FRAME

HEAD

CONTROL

UNIT

POWER

CORD

Installation Instructions for Thermal Guardian Models

WARNING:

DO NOT PLUG IN

POWER CORD UNTIL

MATTRESS IS

COMPLETELY FULL.

UNPLUG POWER CORD

BEFORE DRAINING

MATTRESS .OR

REMOVING TUBES

OF

BED

TOUCH TEMP, QUANTUM Waterbed Heaters

Your Thermal Guardian Wire Alloy Waterbed Heater is designed to be a complete temperature control system
for softside flotation and tube type waterbed systems. The use of any other control unit or attachment

may cause a hazard......................................................................................................................................................

DO NOT USE WITH ANY OTHER BRAND OF CONTROL UNIT, HEATER OR ELECTRICAL DEVICE.
INSTALL THIS HEATING SYSTEM IN TUBE TYPE AND FLOTATION BED STRUCTURES WHERE
THE WATERMATTRESS IS NORMALLY FILLED TO A HEIGHT 8” OR LESS WITH A MINIMUM OF 3”.

CAUTION: FOR COMBINATION MATTRESS (i.e. AIR AND WATER MATTRESS), BE CERTAIN THAT BOTH THE
HE AT E R PAD A N D SE N S O R ARE B O T H L O C A T E D B E N E ATH T H E W AT E R PO R T I O N
ONLY. DO NOT PLACE UNDER NON-WATER FILLED SECTIONS.

SENSOR

FOUNDATION

HEATING PAD

FOOT

FOOT

FOOT

OF

OF

OF

BED

BED

BED

BASE SPLIT

DUAL HEATER SYSTEM SHOWN

READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY.

DO NOT INSTALL HEATER UNTIL ALL INSTRUCTIONS HAVE BEEN READ

AND UNDERSTOOD.

WARNING

FIRE OR ELECTRICAL SHOCK MAY

RESULT FROM IMPROPER USE

1. Select a location for your flotation system.
An electrical outlet should be within 5 ft. of the
temperature control unit, so that an extension
cord will not be necessary. Assemble waterbed
in accordance with mattress manufacturer’s
instructions. DO NOT install liner or watermat­tress at this step (see 9). DO NOT attempt
to install under already filled bed, watermattress
should be drained to ensure heater pad lays
flat with no creases. Creasing pad is hazardous.

2. He ater placem ent . Place hea ter pa d
perpendicular to the head of bed on base
platform surface, with the instructions facing
up, at least 8” from any side (and at least 8”
from the inside edge of any foam rails.)
See illustration to right.

3. Route heater cord through access notch,
grommet or end of zipper run as directed by
mattress or bed manufacturer’s instructions.

4. Control unit must be mounted near corner of
bed to provide adequate length for power cord
and se n s o r to be po s i t i o n e d properly
under mattress. (your bed may have a mount­ing area for the control unit integrated into the
mattress design.)

5. The control unit is ideally installed on the
side of the bed or on the pedestal. Avoid cross­ing the wires exiting the bottom of the control
unit. DO NOT install the control unit upside
down-wires must be at the bottom of the con­trol unit.

6. Secure the control unit with the screws or
tape provided. Plug heater supply cord into
control unit. Do not plug power cord into wall
outlet until mattress is completely full.

7. T h r e ad te m p e rature sensor th rough
notch or grommet or end of zipper run leaving a
minimum section exposed outside the bed frame.

8. The temperature sensor or probe should be
positioned at least 12” from the heater pad and
directly under the watermattress and liner portion
of the flotation system.

TUBE TYPE

TUBE TYPE

WATERBEDS

YESYES

WATERBEDS

1

1

1

1

1

Waterbeds which

Waterbeds which

contain individual

contain individual

tubes or cylinders

tubes or cylinders

filled with water.

filled with water.

Minimum fill depth

Minimum fill depth

3 inches.

3 inches.

9. Install the liner and watermattress in accordance with
manufacturer’s instructions. Make certain there are no folds in
liner or mattress above the heater. Fill with warm water (never
hot). Watermattress should be full BEFORE PLUGGING IN
the power cord to wall outlet.

HEAD

HEAD

HEAD

OF

OF

OF

BED

BED

BED

SENSOR

8” MIN.8” MIN.8” MIN.

12”

MIN.

BASE SPLIT

1” MIN.

FOOT

FOOT

FOOT

OF

OF

OF

BED

BED

BED

HEATING PAD

8” MIN.

8” MIN.

SOFTSIDE FRAME

CONTROL UNIT

AFTER HEATER IS PROPERLY INSTALLED AND

MATTRESS IS COMPLETELY FULL:

10. After your mattress is filled, plug heater pad cord into
heater control unit. Plug control unit power cord into wall outlet. Be sure
all plugs are tight and secure. Turn the control unit knob or push the
buttons when present to its lowest setting. Plug control unit power
cord into wall outlet. Be sure all plugs are tight and secure. Do
not use other control unit or attachment not provided with
the heater due to increased risk of fire or electric shock.

11. Adjust temperature dial or buttons to desired setting, 85
degrees for a good starting point. Expect an increase of about
½ degree per hour. Depending how cold water is, it could take
4-5 days to heat mattress. The indicator light on the Dial will
stay on until the mattress reaches the set temperature or on
Digi tal Control s t he Readou t w ill flash until the mattress
reaches the set temperature at which point the Readout stays
lit. Digital Control ON-OFF buttons will turn heater On or
completely Off. When the temperature drops below the setting,
the heater will be reactivated and the light will once again go
on or if Digital Control will readout will begin to flash. If the
setting proves too warm or cold after a day or so, adjust the
control unit slightly and allow time for the water temperature
to adjust accordingly. Save energy when bed is not use, by
k e e p i n g t h e b e d “ m a d e” t o h e l p r e t a in i t s h e a t .
1 2 . A L WA Y S U N P L U G H E A T E R C O N T R O L U N I T
P O W E R C O R D B E F OR E D R A I NI N G M AT T R E SS O R
REMOVING TUBES, FAILURE TO DO SO WILL VOID WARRANTY!

13. DO NOT TUCK IN BED OR PLACE ANY HEAT INSULATING
MATERIALS OVER THE CONTROL, AS IT MAY CAUSE IT TO
OVERHEAT. .

120 WATTS • 120 VAC

60 Hz • 1 AMPS

MODEL P1013

Fontana, Ca. 92337-8212