INNOLUX MT185GW01 V.B Specification

Global LCD Panel Exchange Center

INNOLUX DISPLAY CORPORATION

MT185GW01 V.B LCD MODULE SPECIFICATION

() Preliminary Specification

() Final Specification

www.panelook.com

Approved by Date

Prepared by Date

Innolux Display Corporation,

No.160 Kesyue Rd., Chu-Nan Site, Hsinchu Science Park,

Chu-Nan 350, Miao-Li County, Taiwan

Tel: 886-37-586000 Fax: 886-37-586060

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

Version Revise Date Page Content

www.panelook.com

InnoLux copyright

Copying forbidden.

Record of Revision

1.0 2009/3/24

Initial Release

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

SPEC NO.

PAGE

MT185GW01 V.B

3/23

Contents:

A. General Specification

B. Electrical Specifications

1. Pin assignment

2. Absolute maximum ratings

3. Electrical characteristics

a. Typical operating conditions

b. Display color vs. input data signals

c. Input signal timing

d. Display position

e. Backlight driving conditions

C. Optical specifications

D. Reliability test items

E. Safety

F. Display quality

G. Handling precaution

H. Label

I. Mechanical drawings

Appendix

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

SPEC NO.

PAGE

MT185GW01 V.B

4/23

A. General specification

NO. Item Specification Remark

1 Display resolution (pixel)

2 Active area (mm)

3 Screen size (inch)

4 Pixel pitch (mm)

5 Color configuration

6 Overall dimension (mm)

7 Weight (g)

1366(H) X 768(V), WXGA Resolution

409.8(H) X 230.4(V)

18.5 inches diagonal

0.3(H) X 0.3(V)

R, G, B vertical stripe

430.37 (W) X 254.6 (H) X 16.5 (D) (Max.)

2100 (max)

8 Surface treatment

9 Input signal interface

10 Display colors

11 Color Saturation

12 Optimum viewing direction

13 RoHS & Halogen Free

Anti-glare, Haze=25%, Hard coating (3H) Glare Optional

One channel LVDS interface

16.7M (6 bit with Hi-FRC)

72% NTSC

6 o’clock

RoHS compliance & Halogen Free

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

B. Electrical specifications

1.Pin assignment

Connector

JAE FI-XB30SSL-HF15 or mechanical interface equivalent connector.

SPEC NO.

PAGE

MT185GW01 V.B

5/23

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

SPEC NO.

PAGE

MT185GW01 V.B

6/23

Rear view of LCM

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

A

[mA]

www.panelook.com

2. Absolute maximum ratings

Parameter Symbol

Min.

Power voltage Vcc

Input signal voltage VLH

Operating temperature Top

Storage temperature TST

CCFL Current ICFL 2 7.5 8 Note 1: The relative humidity must not exceed 90% non-condensing at temperatures of 40°C or less. At temperatures greater than 40°C, the wet bulb tem perature must not exceed 39°C.

Note 2: The unit should not be exposed to corrosive chemicals.

-0.3 -

0 -

-20 -

Values

SPEC NO.

PAGE

Typ .

Max.

6.0 V

4.3 V

50 °C Note 1

60 °C Note 2

MT185GW01 V.B

7/23

Unit

Remark

t 25°C

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

3. Electrical characteristics

a. Typical operating conditions

Item Symbol Min. Typ. Max. Unit Remark

Input Voltage

Permissive Power Input Ripple

Input Current

Rush Current

Logic Input

Voltage

LVDS:

IN+, IN-

Common Mode Voltage

Differential Input Voltage

Threshold Voltage (High)

Threshold Voltage (Low)

Black

White

Mosaic

SPEC NO.

PAGE

V

4.5 5 5.5

cc

V

- -

RF

MT185GW01 V.B

8/23

0.15

Icc - 700 1000

Icc - 500 700

I

- 700 1000

cc

I

- 1.6 3

Rush

mA

VCM - 1.2 -

VID 100 - 600

VTH - - 100

VTL -100 - -

mV

mV Note 5

V

A Note 4

V

Note 1

Note 2

Note 3

Note 1 : The specified current is under the Vcc =5V, 25 °C, fv=60Hz (frame frequency) condition

whereas black pattern is displayed.

Note 2 : The specified current is under the Vcc =5V, 25 °C, fv=60Hz (frame frequency) condition

whereas white pattern is displayed.

Note 3 : The specified current is under the Vcc =5V, 25 °C, fv=60Hz (frame frequency) condition

whereas mosaic pattern(black & white [8*6] ) is displayed.

White : 255 Gray

Black : 0 Gray

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Note 4 : test condition :‘

(1) V

(2) Pattern: Mosaic pattern

= 5 V, VDD rising time = 470 μs ± 10%

DD

90%

(3) Test circuit

V

5 V

DD

R1 47K

SPEC NO.

PAGE

Ton=470 Ӵs  10%

M1 2SK1059

FUSE

MT185GW01 V.B

9/23

VDD ( LCD INPUT)

C1 1uF

CONTROL SIGNAL

(HIGH to LOW)

12V

Note 5: LVDS signal definition

VIN+ = Positive differential DATA & CLK Input

VIN- = Negative differential DATA & CLK Input

VID = VIN+ – VIN- ,

C3 1uF

R3

47K

R2

1K

M2 2SK1399

C2

10000pF

VCM =ΨVCM

VID =ΨVID

VID+ =ΨVIH

VID- =ΨVIL

VCM = (VIN

VCM+ = (VIH

VCM- = (VIL

–VCM-Ψ,

+

–VID-Ψ,

+

–VIH-Ψ,

+

–VIL-Ψ,

+

+VIN-)/2,

+

+VIH-)/2,

+

+VIL-)/2,

+

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Note 6 : Power on sequence for LCD V

T1

Panel Power

Supply V

Interface

Signals

DC

90%

10%

90% 90%

T2

DD

Valid Interface Data

90%

SPEC NO.

PAGE

90%

T6

T5

10%

MT185GW01 V.B

10/23

T7

10%

Backlight Power

Supply

T3 T4

Parameter Value Unit

Min Typ Max ms

T1 0.1 - 10 ms

T2 0 30 50 ms

T3 200 250 - ms

T4 100 250 - ms

T5 0 20 50 ms

T6 0.1 - - ms

T7 1000 - - ms

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

SPEC NO.

PAGE

MT185GW01 V.B

11/23

b. Display color vs. input data signals

The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for the color; the higher the binary input, the brighter the color. The table below provides a reference for color versus data input.

Color

MSB LSB MSB LSB MSB LSB

R7 R6 R5 R4 R3 R2 R1 R0

Red Green Blue

Input color data

G7 G6 G5 G4 G3 G2 G1 G0

B7 B6 B5 B4 B3 B2 B1 B0

Basic colors

Black Red(255) Green(255) Blue(255) Cyan Magenta Yellow White

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

Red

Green

Red(000) dark Red(001) Red(002)

:

Red(253) Red(254) Red(255) bright

Green(000)dark Green(001) G

reen(002)

:

Green(253) Green(254) Green(255)

bright

0

:

1

0

:

0

:

0

1

0

:

0

1

0

:

0

1

0

:

1

0

1

0

:

1

0

1

0

1

0

:

1

0

0 0 0

:

0 0 0

:

1 1 1

0

:

0

1

0

:

0

1

0

1

0

:

0

:

0

:

0

:

0

Blue(000) dark Blue(001) Blue(002)

Blue

Blue(253) Blue(254) Blue(255) bright

0

:

0

:

0

:

0

:

0

0 0 0

:

0 0 0

0

1

0

:

0

1

0

1

0

1

0

1

:

1

0

1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

SPEC NO.

PAGE

MT185GW01 V.B

12/23

c. Input signal timing Support Input Timing Table

Item Description Min. Typ. Max. Unit

period 10.5 13.2 15.9 nS Clock

Dclk

frequency 62.9 75.4 95.6 MHz

Vertical

Horizontal

T

V_TOTAL

T

H_TOTAL

T

V total line number 786 806 900 T

Data duration

V_DATA

Ё

768

Ё

TVB V-blank 18 38 132 T

frequency 50 60 76 Hz

f

V

H_TOTAL

T

H_TOTAL

H total pixel number 1400 1560 1800 DClk

Data duration

H_DATA

H-blank 40 194 434 DClk

T

HB

Ё

1366

Ё

DClk

Note: Because this module is operated by DE only mode, Hsync and Vsync input signals should be set

to low Logic level or ground. Otherwise, this module would operate abnormally.

DATA

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

d. Display Position

D(1, 1) D(2, 1) …… D(683, 1) …… D(1365, 1) D(1366, 1)

D(1, 2) D(2, 2) …… D(683, 2) …… D(1365, 2) D(1366, 2)

. . .

D(1, 384) D(2, 384) …… D(683, 384) …… D(1365, 384) D(1366, 384)

. . .

D(1, 767) D(2, 767) …… D(683, 767) …… D(1365, 767) D(1366, 767)

D(1, 768) D(2, 768) …… D(683, 768) …… D(1365, 768) D(1366, 768)

e. Backlight driving conditions

Parameter Symbol Min. Typ. Max. Unit Remark Remark

Lamp voltage VL 630 700 770 Vrms I=7.5mA Note 1, 2

……

SPEC NO.

. . .

PAGE

……

MT185GW01 V.B

13/23

. . .

Lamp operation current

Lamp starting voltage VLstart

Frequency F 40 - 60 KHZ Note 7

Lamp life time 50000 - - Hr Note 8

IL 2 7.5 8 mArms Note 3

1300 - - T = 25°C Note 4,5,6,7

1700 - -

Vrms

T = 0°C Note 4,5,6,7

Note:• • The waveform of the voltage output of inverter must be area-symmetric and the design of the

inverter must have specifications for the modularized lamp. The performance of the Backlight,

such as lifetime or brightness, is greatly influenced by the characteristics of the DC-AC inverter

for the lamp. All the parameters of an inverter should be carefully designed to avoid producing

too much current leakage from high voltage output of the inverter. When designing or ordering

the inverter please make sure that a poor lighting caused by the mismatch of the Backlight and

the inverter (miss-lighting, flicker, etc.) never occurs. If the above situation is confirmed, the

module should be operated in the same manners when it is installed in your instrument.

Note 1: Specified values are for a single lamp. Note 2: Operating voltage is measured at the condition of Ta = 25±2°C. Note 3: The degree of unbalance: less than 10%

The ratio of wave height: less than

10%2 r

Ip

Ip: high side peak

I-p

I-p: low side

peak

The degree of unbalance = |Ip-I-p| /Irms*100(%)

The ratio of wave height = Ip (or I-p)/Irms

Lamp should be completely turned on.

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Note 4: Test equipment: AS-114B

Note 5: The voltage shown above should be applied to the lamp for more than 1 second after startup. Otherwise, the lamp may not be turned on normally.

Note 6: Inverter should provide more than min. value, and then lamp could be completely turned on.

Note 7: Lamp frequency may produce interference with horizontal synchronous frequency and this may

cause line flow on the display. Therefore lamp frequency shall be detached from the horizontal synchronous frequency and its harmonics as far as possible in order to avoid interference.

Note 8: Life time (Hr) is defined as the time when brightness of a lamp unit itself becomes 50% or less

SPEC NO.

PAGE

MT185GW01 V.B

14/23

than its original value at the condition of Ta = 25±2°C and IL = 7.5mArms.

Backlight connecter: 3500IHS-02L

Pin no. Symbol Function Remark

1 VIH Lamp high voltage input Cable color: Pink

2 VIL Lamp low voltage input Cable color: White

3 VIH Lamp high voltage input Cable color: Blue

4 VIL Lamp low voltage input Cable color: Black

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

yp

www.panelook.com

C. Optical specifications

Item Symbol Condition

Response time

Tr+Tf

Contrast ratio

Viewing angle

CR

Top

Bottom

Left

Tr

Tf

= 0ш

CRЊ10

CRЊˈ

CRЊ10

CRЊˈ

CRЊ10

CRЊˈ

SPEC NO.

PAGE

Specification

Min. T

- 1.5 4

- 3.5 6

- 5 10

700 1000 -

70

75

70

75

.Max.

80

85

80

85

MT185GW01 V.B

15/23

-

Unit Remark

ms Note 4

Note 3,5

deg. Note 3,5,7

Right

Brightness (Center)

YL

Wx

Color chromaticity(CIE)

Wy

Rx

Ry

Gx

Gy

Bx

By

White uniformity (9) 

Cross talk Ct

W

CRЊ10

CRЊˈ

= 0ш

75

200 250 -ʳ

-0.03

0.75 0.80 -ʳ

-ʳ -ʳ 2%

85

0.313

0.329

0.678

0.303

0.284

0.617

0.142

0.067

-

+0.03

nit Note 3,6

Note 3

Note 3,8

Note 9

Note 1: Ambient temperature = 25°C. Note 2: To be measured in dark room after backlight warm up 30 minutes. Note 3: To be measured with a viewing cone of 2°by Topcon luminance meter BM-5A.

Note 4: Definition of response time:

The output signals of BM-7 are measured when the input signals are changed from “Black”

to “White” (falling time) and from “White” to “Black” (rising time), respectively. The response time

interval is between the 10% and 90% of amplitudes. Refer to figure as below.

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

100%

S ig

90%

n a l( R

e la

t

iv e

v a lu

10%

e )

0%

Note 5: Definition of contrast ratio:

Contrast ratio is calculated by the following formula.

Contrast ratio (CR)=

"Black"

Tr

Brightness on the "white" state Brightness on the "black" state

SPEC NO.

PAGE

Tf

MT185GW01 V.B

16/23

"White""White"

Note 6: Driving conditions for CCFL: I

Note 7: Definition of viewing angle

Note 8: Definition white uniformity:

Luminance are measured at the following nine points (P1~P9).



Minimum Brightness of nine points(P1~P9).

=

Maximum Brightness of nine points (P1~P9).

= 7.5 mA, 50 KHz Frequency.

L

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Note 9:

SPEC NO.

1/2

1/6

PAGE

2/3 1/3

A

1/6

A’

127 gray level 127 gray level

B

1/2

MT185GW01 V.B

17/23

1/6

1/3

1/2

B’

2/3

l L

Note 10: Optical characteristic measurement setup.

l / LA x 100%= 2% max., LA and LA’ are brightness at location A and A’

A-LA’

l / LB x 100%= 2% max., LB and LB’ are brightness at location B and B’

B-LB’

0 gray level

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

D. Reliability test items

Test Item Test Condition Judgment Remark

High temperature storage

Low temperature storage

High temperature & high

humidity operation

High temperature operation

Low temperature operation

Thermal Shock

(non-operation)

Electrostatic discharge (ESD)

(non-operation)

60°C, 240Hrs

-20°C, 240Hrs

40°C, 90%RH, 240Hrs

(No condensation)

50°C, 240Hrs

0°C, 240Hrs

-20°C/1Hr ~60°C/1Hr , 100cycles

Contact:+/-8kV, 150pF(330ohms),

25 times/1 point, 1 time/1 sec

SPEC NO.

PAGE

MT185GW01 V.2

18/23

Note 1 Note 2

Air discharge:+/-15kV, 150pF(330ohms), 25

times/1 point, 1 time/1 sec

Vibration

(non-operation)

Mechanical Shock

(non-operation)

MTBF Demonstration 50,000 hours with confidence level 90% Note 1 Note 3

Vibration level : 1.5G

Bandwidth : 10-300Hz

Waveform : sine wave,

sweep rate : 10min

30 min for each direction X, Y, Z

(1.5 Hrs in total)

Shock level : 50G, 11ms

Waveform : Half sine wave

Direction : ±X, ±Y, ±Z

One time each direction

Note 1 Note 2

Note1: Pass: Normal display image with no obvious non-uniformity and no line defect.

Partial transformation of the module parts should be ignored.

Fail: No display image, obvious non-uniformity, or line defects.

Note2: Evaluation should be tested after storage at room temperature for one hour.

Note 3: The MTBF calculation is based on the assumption that the failure rate distribution meets the

Exponential Model (CCFL excluded)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

SPEC NO.

PAGE

MT185GW01 V.2

19/23

E. Safety

(1) Sharp Edge Requirements

There will be no sharp edges or corners on the display assembly that could cause injury.

(2) Materials

a. Toxicity

There will be no carcinogenic materials used anywhere in the display module. If toxic materials are

used, they will be reviewed and approved by the responsible InnoLux Toxicologist.

b. Flammability

All components including electrical components that do not meet the flammability grade UL94-V1 in

the module will complete the flammability rating exception approval process. The printed circuit

board will be made from material rated 94-V1 or better. The actual UL flammability rating will be

printed on the printed circuit board.

c. Capacitors

If any polarized capacitors are used in the display assembly, provisions will be made to keep them

from being inserted backwards.

F. Display quality

The display quality of the color TFT-LCD module should be in compliance with the

Innolux’s Incoming inspection standard.

G. Handling precaution

The Handling of the TFT-LCD should be in compliance with the Innolux’s handling principle standard.

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

m

www.panelook.com

H. Label

(1) Module Label

18 mm

(a) Model Number: MT185GW01

(b) Version: V.2

(c) Serial ID I: Z

MT185GW01 V.A AM1850001 2xx

Z1 Z2 Z3 Z4 Z

Z1 'Z2'-Z3' Z4'Z 5'Z 6'Z7'-Z8' - Z9 '- Z10 '- Z11' Z12'-Z13'-Z14' Z15' -Z16 '-Z17 'Z18' Z19' -Z20'Z21'Z22 ' Z

Z2 Z3 Z4 Z 5 Z

1

--Z 7--Z8 Z9 Z10 Z

5 Z 6

6

Z

73 m

11 Z 12

Z8 Z

7

SPEC NO.

PAGE

Z

9 Z10

11

MT185GW01 V.2

20/23

'

23

Z

MADE IN XXX

12

Serial ID includes the information as below:

1. Manufactured Date: Year: 0~9, for 2000~2009

2. Month: 1~9 & A~C for Jan.~Dec.

3. Date: 1~9 & A~Z (exclude I, O, Q, U) for 1st~31th

4. Code of grade: 1, 2, 3, 5, E

5. Serial No: Module manufacture sequence no

Serial No

Code of grade

INL internal use

Year, Month, Date

INL internal use

(d) Serial ID II (INL internal use)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

(2) Carton Label

INNOLUX DISPLAY

BOX ID :

60 mm

Model No. MT185GW01 V.A

AM1850001 2XX

Quantity : 7 PCS

MFG Date: 20XX/XX/XX

QC: Made in XXX

Z1 Z2 Z3 Z4 --Z 5--Z6 Z7 Z8 Z 9

SPEC NO.

PAGE

MT185GW01 V.2

21/23

100 mm

(a) Model Number: MT185GW01

(b) Version: V.A

(c) Packing quantity: 7 pcs

(d) Serial ID: Z

Z2 Z3 Z4 Z 5 Z6 Z

1

7 Z8

Z 9

Serial No

Code of grade

Serial ID includes the information as below:

(a) Manufactured Date: Year: 0~9, for 2000~2009

Month: 1~9 & A~C for Jan.~Dec.

Date: 1~9 & A~Z (exclude I, O, Q, U) for 1st~31th

Year, Month, Date

INL internal use

(b) Code of grade: 1,2, 3, 5, E

(c) Serial No: Module packing sequence no

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

I. ME Drawing

(1) Front view

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

(2) Back view

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

INNOLUX MT185GW01 V.B Specification

Specifications and Main Features

Frequently Asked Questions

User Manual