INNOLUX DISPLAY CORPORATION
BT156GW01 V.1 LCD MODULE SPECIFICATION
( ) Preliminary Specification
(●) Final Specification
Customer Checked & Approved by
Approved by Checked by Prepared by
MKT PD PM
www.jxlcd.com
www.jxlcd.com
Innolux Display Corporation
No.160 Kesyue Rd., Chu-Nan Site, Hsinchu Science Park,
Annie Lu
Date: 2009/02/05
Chu-Nan 350, Miao-Li County, Taiwan
Tel: 886-37-586000 Fax: 886-37-586060
Version: 1
Record of Revision
Version Revise Date Page Content
InnoLux copyright
All rights reserved,
Copying forbidden.
0 2008/10/30
1 2009/02/05
www.jxlcd.com
www.jxlcd.com
All First Edition issued
4 General Block Diagram-PCBA shape modified.
12 Color coordinators finalized.
19 Packing form modified.
21
Appendix EDID code finalized.
Mechanical drawing-rear side, The “Don’t Touch” caution
on PET sheet had been reversed.
Contents: Page
SPEC NO.
PAGE
BT156GW01 V.1
1/24
1 . General Specifications
2 . Electrical Specifications
2-1 Pin Assignment
2-2 Absolute Maximum Ratings
2-3 Electrical Characteristics
3 . Optical Specifications
4. Reliability Test Items
5. Safety
6. Display Quality
7. Handling Precaution
8. Label Definition
2
3
5
6
12
15
16
16
16
17
9. Packing Form
10. Mechanical Drawings
Appendix
www.jxlcd.com
www.jxlcd.com
19
21
22
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
1. General Specifications
NO. Item Specification Unit
1 Display resolution (pixel) 1366(H) X 768(V), HD resolution
2 Active area 344.232(H) X 193.536(V) mm
3 Screen size 15.6 inches diagonal Inches
4 Pixel pitch 0.252(H) X 0.252(V) mm
5 Color configuration Stripe
6 Overall dimension 359.8(W) X 210(H) X 5.5(D) (max) mm
7 Weight 450Max. Grams
8 Surface treatment Hard coating-3H
9 Input color signal 6 bit LVDS
10 Display colors 262K (6 bit)
SPEC NO.
PAGE
BT156GW01 V.1
2/24
11 Optimum viewing direction 6 o’clock
12 Backlight W-LED
13 RoHS RoHS compliance
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
www.jxlcd.com
www.jxlcd.com
2. Electrical Specifications
2-1 Pin Assignment
a. Panel connector
Connector Part No.: 20455-040-12 (I-PEX) or equivalent
User’s connector Part No: 20453-040T-12 (I-PEX) or equivalent
Pin No Symbol Description Remark
1 DIAG_LOOP Plug detection pin
2 VCC Power Supply (+3.3V)
3 VCC Power Supply (+3.3V)
4 V
5 BIST BIST function enable (+3.3V)
6 Clk
7 DATA
8 Rxin0- Differential Data Input
9 Rxin0+ Differential Data Input
10 GND Ground
11 Rxin1- Differential Data Input
12 Rxin1+ Differential Data Input
13 GND Ground
14 Rxin2- Differential Data Input
15 Rxin2+ Differential Data Input
16 GND Ground
17 CLK- Differential Clock Input
18 CLK+ Differential Clock Input
www.jxlcd.com
19 NC No connection (Reserve)
20 NC No connection (Reserve)
21 NC No connection (Reserve)
22 NC No connection (Reserve)
23 NC No connection (Reserve)
24 NC No connection (Reserve)
25 NC No connection (Reserve)
26 NC No connection (Reserve)
27 NC No connection (Reserve)
28 NC No connection (Reserve)
29 NC No connection (Reserve)
30 NC No connection (Reserve)
31 LED_GND LED Ground
32 LED_GND LED Ground
33 LED_GND LED Ground
34 DIAG_LOOP Plug detection pin
35 LED_PWM PWM dimming signal input
36 LED_EN LED enable pin (3.3V)
37 NC No connection (Reserve)
38 V_LED LED power supply 7.5V~21V
39 V_LED LED power supply 7.5V~21V
40 V_LED LED power supply 7.5V~21V
www.jxlcd.com
DDC Power +3.3V
EDID
DDC Clock
EDID
DDC Data
EDID
SPEC NO.
PAGE
B2~B5,DE,Hsync,Vsync
BT156GW01 V.1
3/24
R0~R5,G0
G1~G5,B0,B1
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
b. General Block Diagram
VR
DC/DC
DC/DC
Components
www.jxlcd.com
www.jxlcd.com
TFT
20455-040
Connector plug in direction
Connector: 20455-040(I-PEX)
Pin1
T-CON
SPEC NO.
PAGE
Pin1
BT156GW01 V.1
4/24
FPC
LED
Driver
PCB
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
V
2-2. Absolute Maximum Ratings
SPEC NO.
PAGE
BT156GW01 V.1
5/24
Parameter Symbol
Min. Max.
Power input voltage VCC - 0.3 4.0 V At 25°C
Input signal voltage VIN - 0.3 4.0 V At 25°C
Operating temperature Top 0 50 °C Note 1
Storage temperature TST - 20 60 °C Note 2
Re-screw - 5 Times
Assured torque at side mount - 2 kgf.cm
Note 1: The relative humidity must not exceed 90% non-condensing at temperatures of 40°C or
less. At temperatures greater than 40°C, the wet bulb temperature must not exceed 39°C.
Note 2: The unit should not be exposed to corrosive chemicals.
Relative Humidity (%RH)
-30 -20 -10 0 10 20 30 40 50 60 70
www.jxlcd.com
100
90
www.jxlcd.com
80
70
60
50
40
30
20
10
Operation Range
Storage Range
0
Temperature (°C)
alues
Unit
Remark
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
2-3. Electrical Characteristics
a. Typical operating conditions
Item Symbol Min. Typ. Max. Unit Remark
SPEC NO.
PAGE
BT156GW01 V.1
6/24
Power input voltage
Permissive power input ripple
Power input current
Power consumption
Differential input high
threshold voltage
Differential input low
LVDS
interface
Note 1: The specified input current and power consumption are under the V
Note 2: LVDS waveform diagram
Rxin+/CLK+
Rxin-/CLK-
threshold voltage
Common input
voltage
Terminating resistor
Rush current
=60Hz (frame frequency) condition whereas black pattern is displayed.
f
V
www.jxlcd.com
www.jxlcd.com
V
3 3.3 3.6 V
CC
V
- - 0.1 V
RF
I
- 360 400 mA Note 1
CC
P
- 1.2 1.3 Watts Note 1
C
V
- - +100 mV
LVT H
V
-100 - - mV
LVT L
V
0.1 1.2 1.4 V Note 2
LVC
R
90 100 110 ohm
T
I
- - 1.5 A Note 3
Rush
V
LVC
Note 2
V
LVC
Note 2
=3.3 V, 25 °C,
cc
V
V
=1.2V,
=1.2V,
LVT H
LVT L
V
LVC
GND
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
SPEC NO.
PAGE
BT156GW01 V.1
7/24
Note 3: Test condition
(1) Pattern: Black pattern
(2) V
= 3.3 V, VCC rising time = 470 μs ± 10%
CC
Control signal
(High to low)
90%
10%
V
CC
Ton=470µs±10%
(3) Test circuit
3.3 V
R1
47K
R2
www.jxlcd.com
www.jxlcd.com
12V
C3
1uF
1K
R3
47K
M1
2SK1059
C2
10000pF
M2
2SK1399
FUSE
C1
1uF
VCC ( LCD input)
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
b. Power sequence
SPEC NO.
PAGE
BT156GW01 V.1
8/24
Power supply for LCD, VCC
Interface data signal, V
(LVDS signal of transmitter)
Backlight on/off
Power sequence timing table
Parameter
T1 0.5 - 10 ms
T2 0 - 50 ms
T3 200 - - ms
i
Min. Typ. Max.
0V
10%
90%
T
0V
Value
90%
10%
T
T6
T
1
2
Valid Data
T
3
Lamp On OFF OFF
T
5
T
4
7
Units
T4 200 - - ms
www.jxlcd.com
T5 0 - 50 ms
www.jxlcd.com
T6 0 - 10 ms
T7 400 - - ms
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
c. Display color vs. input data signals
Signal Name Description Remark
SPEC NO.
PAGE
BT156GW01 V.1
9/24
R5 Red Data 5 (MSB)
R4 Red Data 4
R3 Red Data 3
R2 Red Data 2
R1 Red Data 1
R0 Red Data 0 (LSB)
Red-pixel Data
G5 Green Data 5 (MSB)
G4 Green Data 4
G3 Green Data 3
G2 Green Data 2
G1 Green Data 1
G0 Green Data 0 (LSB)
Green-pixel Data
B5 Blue Data 5 (MSB)
B4 Blue Data 4
B3 Blue Data 3
B2 Blue Data 2
Red-pixel data. Each red pixel's brightness data
consists of these 6 bits pixel data.
Green-pixel data. Each green pixel's brightness
data consists of these 6 bits pixel data.
Blue-pixel data. Each blue pixel's brightness data
consists of these 6 bits pixel data.
B1 Blue Data 1
B0 Blue Data 0 (LSB)
www.jxlcd.com
www.jxlcd.com
Blue-pixel Data
Signal for 1 DCLK cycle (t
)
CLK
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
d. Input signal timing
Timing table
Description Symbol Min Typ Max Unit
Frame rate -- 50 60 -- Hz
SPEC NO.
PAGE
BT156GW01 V.1
10/24
Clock freq. 1/t
Line cycle time tH 1400 1560 1800
Line width-active tHd 1366 1366 1366
Frame cycle time tV 780 806 900 tH
V width-active tVd 768 768 768 tH
DE
DE
DCLK
www.jxlcd.com
www.jxlcd.com
t
CLK
65 75 85 MHz
CLK
t
V
t
Vd
t
H
t
Hd
t
CLK
t
CLK
e. Display position
D(1, 1) D(2, 1) …… D(683, 1) …… D(1365, 1) D(1366, 1)
D(1, 2) D(2, 2) …… D(683, 2) …… D(1365, 2) D(1366, 2)
.
.
.
D(1, 384) D(2, 384) …… D(683, 384) …… D(1365, 384) D(1366, 384)
.
.
.
D(1, 767) D(2, 767) …… D(683, 767) …… D(1365, 767) D(1366, 767)
D(1, 768) D(2, 768) …… D(683, 768) …… D(1365, 768) D(1366, 768)
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
……
……
.
.
.
.
.
.
……
……
.
.
.
.
.
.
.
.
.
.
.
.
f. Backlight driving conditions
Parameter Symbol Min. Typ. Max. Unit Remark
SPEC NO.
PAGE
BT156GW01 V.1
11/24
LED Forward Voltage V
LED Forward Current
Power consumption
Output PWM frequency F
Duty ratio - 20 %
LED life time - 15,000 Hr T = 25°C , Note 1
Note 1: LED life time definition is Brightness decrease to 50% of initial or abnormal lighting.
g. Module function block
www.jxlcd.com
www.jxlcd.com
LED driver
controller
3 3.2 3.4 V
F
IF 20 mA
P
3.93 4.20 W
LED
200 Hz T = 25°C
PWM
LED Light-bar
TFT-LCD
Source driver
Timing
Step-up regulator
& reference voltage
generator
LVDS connector
rms
rms
EDID
EEPROM
T = 25°C
T = 25°C
T = 25°C
Gate driver
LVDS DATA BUS mini-LVDS & CONTROL BUS POWER I2C BUS
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
SPEC NO.
PAGE
BT156GW01 V.1
12/24
3. Optical specifications
Ambient temperature = 25°C.
Item Symbol Condition
Specification
Min. Typ. Max.
Unit Remark
Response time
Contrast ratio CR
Viewing angle
Brightness
(5 points average)
Color chromaticity (CIE)
www.jxlcd.com
www.jxlcd.com
Tr+Tf θ= 0∘
θ= 0∘
Top
Bottom
Left
Right
200 220 nit Note 2,5
Y
L
Wx
Wy
Rx
Ry
Gx
Gy
Bx
CR≧10
CR≧10
CR≧10
CR≧10
θ= 0∘
500:1 600:1 Note 2,4
15
30
40
40
-0.02
8 15 ms Note 3
deg Note 2,4,6
0.313
0.329
0.620
0.340
0.330
0.605
0.150
+0.02
Note 2
B
y
Color Gamut NTSC CIE1931 56 60 % -
δ
0.8
W(5)
White uniformity
0.65
δ
W(13)
Cross talk Ct 2% Note 8
Note 1: To be measured in dark room.
Note 2: To be measured with a viewing cone of 2°by Topcon luminance meter BM-5A.
Note 3: Definition of response time:
The output signals of BM-7 are measured when the input signals are changed from “Black” to
“White” (falling time) and from “White” to “Black” (rising time), respectively. The response time
interval is between 10% and 90% of amplitudes. Refer to figure as below.
0.070
Note 2,7
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
(
Avg
)
SPEC NO.
PAGE
BT156GW01 V.1
13/24
100%
S
i
90%
g
n
a
l
(
R
e
l
a
t
i
v
e
v
a
l
u
10%
e
)
0%
Note 4: Definition of contrast ratio:
Contrast ratio is calculated with the following formula:
Note 5: Driving current for LED should be 20 mA.
Note 6: Definition of viewing angle
Contrast ratio
Luminance is measured at the following thirteen points (1~13):
Y
= (Y3+ Y5+Y7+Y11 +Y12) / 5
L
www.jxlcd.com
www.jxlcd.com
Tr
of 5pts
=
"Black"
L white (Avg of 5pts.)
L
Black (Avg of 5pts.)
"White""White"
Tf
Note 7: Definition white uniformity
Luminance is measured at the following thirteen points (1~13):
δ
Minimum Brightness of thirteen points
W(13) =
δ
W(5) =
Maximum Brightness of thirteen points
Minimum Brightness of five points
Maximum Brightness of five points
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
13 point measuring locations refer to the point 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12 and 13.
5 point measuring locations refer to the point 3, 5, 7, 11 and 12.
SPEC NO.
PAGE
BT156GW01 V.1
14/24
Note 8:
1/2
A
www.jxlcd.com
www.jxlcd.com
127 gray level 127 gray level
Unit: percentage of dimension of display area
l L
l L
l / LA x 100%= 2% max., LA and L
A-LA’
l / LB x 100%= 2% max., LB’ and LB’ are brightness at location B and B’
B-LB’
1/6
B
1/6
1/2
2/3 1/3
are brightness at location A and A’
A’
1/2
A’
0 gray level
1/6
1/6
1/3
1/2
B’
2/3
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
4. Reliability test items
Test Item Test Condition Judgment Remark
SPEC NO.
PAGE
BT156GW01 V.1
15/24
High temperature storage
Low temperature storage
High temperature & high
humidity operation
High temperature operation 50°C, 240 hours Note 1 Note 2
Low temperature operation 0°C, 240 hours Note 1 Note 2
Thermal Shock
(Non-operation)
Electrostatic discharge (ESD)
Vibration
(Non-operation)
Mechanical shock
(Non-operation)
Note 1: Pass: Normal display image with no obvious non-uniformity and no line defect.
Fail: No display image, obvious non-uniformity, or line defects.
Note 2: Evaluation should be tested after storage at room temperature for one hour.
www.jxlcd.com
www.jxlcd.com
Partial transformation of the module parts should be ignored.
60°C, 240 hours
-20°C, 240 hours
40°C, 90% RH, 240 hours
(No condensation)
-25°C / 30 mins ~ 65°C / 30 mins
100 cycles
150 pF, 330Ω,
Contact: ±8kV, Air: ±15kV
1.5G, 10 to 500 Hz random; 0.5hr in each
perpendicular axes ( X, Y, Z ).
220G/2ms, Half sine wave, ±X, ±Y, ±Z one
time for each direction
Note 1 Note 2
Note 1 Note 2
Note 1 Note 2
Note 1 Note 2
Note 1
Note 1 Note 2
Note 1 Note 2
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
5. Safety
5-1. Sharp edge requirements
There will be no sharp edges or corners on the display assembly that could cause injury.
5-2. Materials
a. Toxicity
There will be no carcinogenic materials used anywhere in the display module. If toxic materials
are used, they will be reviewed and approved by the responsible InnoLux Toxicologist.
b. Flammability
All components including electrical components that do not meet the flammability grade UL94-V0
in the module will complete the flammability rating exception approval process. The printed circuit
board will be made from material rated 94-V0 or better. The actual UL flammability rating will be
printed on the printed circuit board.
SPEC NO.
PAGE
BT156GW01 V.1
16/24
c. Capacitors
If any polarized capacitors are used in the display assembly, provisions will be made to keep
them from being inserted backwards.
6. Display quality
The display quality of the color TFT-LCD module should be in compliance with the InnoLux
incoming inspection standard.
www.jxlcd.com
www.jxlcd.com
7. Handling precaution
(1) Do not apply rough force such as bending or twisting to the module during assembly.
(2) To assemble or install module into user’s system can be only in clean working areas. The
dust and oil may cause electrical short or worsen the polarizer.
(3) It’s not permitted to have pressure or impulse on the module because the LCD panel and
Backlight will be damaged.
(4) Always follow the correct power sequence when LCD module is connecting and
operating.
(5) Do not pull the I/F connector in or out while the module is operating.
(6) Do not disassemble the module.
(7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is
very soft and easily scratched.
(8) It is dangerous that moisture come into or contacted the LCD module, because moisture
may damage LCD module when it is operating.
(9) High temperature or humidity may reduce the performance of module. Please store LCD
module within the specified storage conditions.
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
SPEC NO.
PAGE
BT156GW01 V.1
17/24
8. Label Definition
8-1. Module label
73 mm
BT156GW01 V.1 AB1560001 00X
18 mm
(a) Model Number : BT156GW01 V.1
(b) Product Number : AB156000100X
(c) Serial ID I : Z
www.jxlcd.com
www.jxlcd.com
Serial ID includes the information as below:
Manufactured Date: Year: 0~9, for 2000~2009
Month: 1~9 & A~C for Jan.~Dec.
Date: 1~9 & A~Z (exclude I, O, Q, U) for 1th~31th
Serial No.: Module manufactures sequential number.
CN-XXXXXX-XXXXX-
XXX-XXXX-XXX
Made In China
DP/N XXXXXX
Z2 Z3 Z4 Z 5 Z
1
Z1 Z2 Z3 Z4 Z
- Z 7 - Z
6
INNOLux
9 Z10
Z
Serial No.
INL internal use
INL internal use
INL internal use
Year, Month, Date.
INL internal use
5 Z 6-Z 7-Z8 Z9 Z10 Z 11 Z 12
Z
8
11
Z
12
TM
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
8-2. Carton label
BT156GW01 V.1
AB1560001 00X
SPEC NO.
PAGE
BT156GW01 V.1
18/24
www.jxlcd.com
www.jxlcd.com
(a) BOX ID (INL internal use)：XXXX-X-XXXX
(b) Model Number：BT156GW01 V.1
(c) Product Number：AB156000100X
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
9. Packing Form
SPEC NO.
PAGE
BT156GW01 V.1
19/24
www.jxlcd.com
www.jxlcd.com
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
10. Mechanical drawings
10-1 Front Side
SPEC NO.
PAGE
BT156GW01 V.1
20/ 24
24/24
www.jxlcd.com
www.jxlcd.com
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
10-2 Rear Side
SPEC NO.
PAGE
BT156GW01 V.1
21 / 24
25/24
www.jxlcd.com
www.jxlcd.com
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
SPEC NO.
PAGE
BT156GW01 V.1
22 / 24
26/24
Appendix: EDID Code
Byte Value Value
(hex)
Header
EDID Version
Vendor / Product
Display
Parameters
Panel Color
Coordinates
Timings
Established
Standard Timing ID
0 Header 00 00000000
1 Header FF 11111111
2 Header FF 11111111
3 Header FF 11111111
4 Header FF 11111111
5 Header FF 11111111
6 Header FF 11111111
7 Header 00 00000000
8 EISA manufacture code = 3 Character ID 25 00100101
9 EISA manufacture code (Compressed ASCII) CC 11001100
0A Panel Supplier Reserved – Product Code 01 00000001
0B Panel Supplier Reserved – Product Code 00 00000000
0C LCD module Serial No - Preferred but Optional (“0” if not used) 00 00000000
0D LCD module Serial No - Preferred but Optional (“0” if not used) 00 00000000
0E LCD module Serial No - Preferred but Optional (“0” if not used) 00 00000000
0F LCD module Serial No - Preferred but Optional (“0” if not used) 00 00000000
10 Week of manufacture 00 00000000
11 Year of manufacture – 1990 (ex. 2005-1990=15) -->2009 13 00010011
12 EDID structure version # = 1 01 00000001
13 EDID revision # = 3 03 00000011
14 Video I/P definition = Digital I/P (80h) 90 10010000
15 Max H image size = (34.423=34 cm) 22 00100010
16 Max V image size = (19.354=19 cm) 13 00010011
17 Display gamma = (gamma ×100)-100 = Example: ( 2.2×100 ) – 100 = 120 78 01111000
18 Feature support ( no DPMS, Active off, RGB, timing BLK 1) 0A 00001010
19 Red/Green Low bit (RxRy/GxGy) C8 11001000
www.jxlcd.com
www.jxlcd.com
1A Blue/White Low bit (BxBy/WxWy) 86 10000110
1B Red x Rx=0.620 9E 10011110
1C Red y Ry=0.340 57 01010111
1D Green x Gx=0.330 54 01010100
1E Green y Gy=0.605 9B 10011011
1F Blue x Bx=0.150 26 00100110
20 Blue y By=0.070 12 00010010
21 White X Wx=0.306 4E 01001110
22 White Y Wy=0.326 53 01010011
23 Established timings 1 (00h if not used) 00 00000000
24 Established timings 2 (00h if not used) 00 00000000
25 Manufacturer’s timings (00h if not used) 00 00000000
26 Standard timing ID1 (01h if not used) 01 00000001
27 Standard timing ID1 (01h if not used) 01 00000001
28 Standard timing ID2 (01h if not used) 01 00000001
29 Standard timing ID2 (01h if not used) 01 00000001
2A Standard timing ID3 (01h if not used) 01 00000001
2B Standard timing ID3 (01h if not used) 01 00000001
2C Standard timing ID4 (01h if not used) 01 00000001
2D Standard timing ID4 (01h if not used) 01 00000001
2E Standard timing ID5 (01h if not used) 01 00000001
2F Standard timing ID5 (01h if not used) 01 00000001
30 Standard timing ID6 (01h if not used) 01 00000001
31 Standard timing ID6 (01h if not used) 01 00000001
32 Standard timing ID7 (01h if not used) 01 00000001
33 Standard timing ID7 (01h if not used) 01 00000001
Field Name and Comments
(hex) (binary)
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
Timing Descriptors #1
Timing Descriptors #2
Timing Descriptors #3
34 Standard timing ID8 (01h if not used) 01 00000001
35 Standard timing ID8 (01h if not used) 01 00000001
36 Pixel Clock/10,000 (Pixel Clock=75.4MHz) (LSB) 74 01110100
37 Pixel Clock/10,000 (Pixel Clock=75.4MHz) (MSB) 1D 00011101
38 Horizontal Active = 1366 pixels (lower 8 bits) 56 01010110
39 Horizontal Blanking (Thbp) = 194 pixels (lower 8 bits) C2 11000010
3A Horizontal Active/Horizontal blanking (Thbp) (upper4:4 bits) 50 01010000
3B Vertical Active = 768 lines 00 00000000
3C Vertical Blanking (Tvbp) = 38 lines (DE Blanking typ. for DE only panels) 26 00100110
3D Vertical Active : Vertical Blanking (Tvbp) (upper4:4 bits) 30 00110000
3E Horizontal Sync, Offset (Thfp) = 48 pixels 30 00110000
3F Horizontal Sync, Pulse Width = 32 pixels 20 00100000
40 Vertical Sync, Offset (Tvfp) = xx lines Sync Width = xx lines 36 00110110
41 Horizontal Vertical Sync Offset/Width upper 2 bits 00 00000000
42 Horizontal Image Size =344 mm 58 01011000
43 Vertical image Size = 194 mm C2 11000010
44 Horizontal Image Size / Vertical image size 10 00010000
45 Horizontal Border = 0 (Zero for Notebook LCD) 00 00000000
46 Vertical Border = 0 (Zero for Notebook LCD) 00 00000000
Non-interlaced, Normal, no stereo, Separate sync, H/V pol Negatives,
47
DE only note: LSB is set to “1” if panel is DE-timing only. H/V can be ignored.
48 Pixel Clock/10,000 (Pixel Clock=75.4MHz) (LSB) 74 01110100
49 Pixel Clock/10,000 (Pixel Clock=75.4MHz) (MSB) 1D 00011101
4A Horizontal Active = 1366 pixels (lower 8 bits) 56 01010110
4B Horizontal Blanking (Thbp) = 194 pixels (lower 8 bits) C2 11000010
4C Horizontal Active/Horizontal blanking (Thbp) (upper4:4 bits) 50 01010000
4D Vertical Active = 768 lines 00 00000000
4E Vertical Blanking (Tvbp) = 38 lines (DE Blanking typ. for DE only panels) 26 00100110
4F Vertical Active : Vertical Blanking (Tvbp) (upper4:4 bits) 30 00110000
50 Horizontal Sync, Offset (Thfp) = 48 pixels 30 00110000
www.jxlcd.com
www.jxlcd.com
51 Horizontal Sync, Pulse Width = 32 pixels 20 00100000
52 Vertical Sync, Offset (Tvfp) = xx lines Sync Width = xx lines 36 00110110
53 Horizontal Vertical Sync Offset/Width upper 2 bits 00 00000000
54 Horizontal Image Size =344 mm 58 01011000
55 Vertical image Size = 194 mm C2 11000010
56 Horizontal Image Size / Vertical image size 10 00010000
57 Horizontal Border = 0 (Zero for Notebook LCD) 00 00000000
58 Vertical Border = 0 (Zero for Notebook LCD) 00 00000000
59 Module “A” Revision = Example: 00, 01, 02, 03, etc. 1A 00011010
5A Flag 00 00000000
5B Flag 00 00000000
5C Flag 00 00000000
5D Dummy Descriptor FE 11111110
5E Flag 00 00000000
5F Dell P/N 1st Character "U" 55 01010101
60 Dell P/N 2nd Character "8" 38 00111000
61 Dell P/N 3rd Character "8" 38 00111000
62 Dell P/N 4th Character "4" 34 00110100
63 Dell P/N 5th Character "M" 4D 01001101
64 LCD Supplier EEDID Revision # 80 10000000
65 Manufacturer P/N"00" 30 00110000
Dell specific information
66 Manufacturer P/N 30 00110000
67 Manufacturer P/N 0A 00001010
68 Manufacturer P/N 20 00100000
69 Manufacturer P/N 20 00100000
6A Manufacturer P/N 20 00100000
SPEC NO.
PAGE
BT156GW01 V.1
23 / 24
27/24
1A 00011010
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
Timing Descriptors #4
Checksum
Manufacturer P/N (If <13 char, then terminate with ASCII code 0Ah, set remaining char = 20h)
6B
6C Flag 00 00000000
6D Flag 00 00000000
6E Flag 00 00000000
6F Data Type Tag: 00 00000000
70 Flag 00 00000000
71 Reserved 00 00000000
72 Reserved 00 00000000
73 Reserved 00 00000000
74 Reserved 00 00000000
75 Reserved 00 00000000
76 Reserved 00 00000000
77 Reserved 00 00000000
78 Reserved 00 00000000
79 Number of LVDS receiver chips = ‘01’ or ‘02’ 01 00000001
7A BIST Enable: Yes = ‘01’ No = ‘00’ 01 00000001
7B (If <13 char, then terminate with ASCII code 0Ah, set remaining char = 20h) 0A 00001010
7C (If <13 char, then terminate with ASCII code 0Ah, set remaining char = 20h) 20 00100000
7D (If <13 char, then terminate with ASCII code 0Ah, set remaining char = 20h) 20 00100000
7E Extension flag (# of optional 128 EDID extension blocks to follow, Typ = 0) 00 00000000
7F Checksum (The 1-byte sum of all 128 bytes in this EDID block shall = 0) 6F 01101111
SPEC NO.
PAGE
BT156GW01 V.1
24 / 24
28/24
20 00100000
www.jxlcd.com
www.jxlcd.com
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PRPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
Loading...