Page 1
Chimei-Innolux Corporation
BT140GW03 V.A LCD MODULE SPECIFICATION
( ) Preliminary Specification
(●) Final Specification
Customer Checked & Approved by
Lenovo ( China )
Approved by Checked by Prepared by
MKT PD PM
www.jxlcd.com
www.jxlcd.com
楊竣傑 柯瑞峰 詹銘斯 陳郁甫
Chimei-Innolux Corporation
No.160 Kesyue Rd., Chu-Nan Site, Hsinchu Science Park,
Chu-Nan 350, Miao-Li County, Taiwan
Date: 2010/10/07
Tel: 886-37-586000 Fax: 886-37-586060
Page 2
Version: 6
Record of Revision
Version Revise Date Page Content
Chimei-Innolux copyright
All rights reserved,
Copying forbidden.
0
1 2010/04/15 5 Pin Assignment
2 2010/04/26
3 2010/05/20
4 2010/07/05
5 2010/08/24 14 PWM frequency
19 RA test criteria
21 Label Drawing
29 EDID Check Sum
6 2010/10/07 16, 18 Definition of color chromaticity (CIE)
2010/04/13
www.jxlcd.com
www.jxlcd.com
All First Edition issued
8 Typical Operating Conditions
21 Label
16
26~29 EDID
Optical specifications
Page 3
Contents: Page
SPEC NO.
PAGE
BT140GW03 V.A
3/29
1 . General Specifications
2 . Electrical Specifications
2-1 Pin Assignment
2-2 Absolute Maximum Ratings
2-3 Electrical Characteristics
3 . Optical Specifications
4. Reliability Test Items
5. Safety
6. Display Quality
7. Handling Precaution
8. Label Definition
4
5
7
8
16
19
20
20
20
21
9. Packing Form
10. Mechanical Drawings
Appendix
www.jxlcd.com
www.jxlcd.com
23
24
26
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 4
1. General Specifications
NO. Item Specification Unit
1 Display resolution (pixel) 1366(H) X 768(V), HD resolution
2 Active area 309.40(H) X 173.95(V) mm
3 Screen size 14.0 inches diagonal Inches
4 Pixel pitch 0.2265(H) X 0.2265(V) mm
5 Color configuration Stripe
SPEC NO.
PAGE
BT140GW03 V.A
4/29
6 Overall dimension
7 Weight
8 Surface treatment Glare
9 Input color signal 6 bit LVDS
10 Display colors 262K (6 bit)
11 Optimum viewing direction 6 o’clock
12 Backlight W-LED
13 RoHS RoHS compliance
www.jxlcd.com
www.jxlcd.com
320.9(W) X 199.1(H) X 3.6(D) (max)
320Max.
mm
Grams
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 5
2. Electrical Specifications
2-1 Pin Assignment
a. Panel connector
Connector Part No:
User’s connector Part No: 20453-040T-12 (I-PEX) or equivalent
Pin No Symbol Description Remark
GS13401-1110S-7H (Foxconn )
SPEC NO.
PAGE
BT140GW03 V.A
5/29
1
2 VCC Power Supply (+3.3V)
3 VCC Power Supply (+3.3V)
4 V
5 NC No connection (Reserve)
6 Clk
7 DATA
8 Rxin0- Differential Data Input
9 Rxin0+ Differential Data Input
10 GND Ground
11 Rxin1- Differential Data Input
12 Rxin1+ Differential Data Input
13 GND Ground
14 Rxin2- Differential Data Input
15 Rxin2+ Differential Data Input
16 GND Ground
17 CLK- Differential Clock Input
18 CLK+ Differential Clock Input
19 CE_EN Color Engine Enable (Reserve)
20 NC No connection (Reserve)
21 NC No connection (Reserve)
22 GND Ground
23 NC No connection (Reserve)
24 NC No connection (Reserve)
25 GND Ground
26 NC No connection (Reserve)
27 NC No connection (Reserve)
28 GND Ground
29 NC No connection (Reserve)
30 NC No connection (Reserve)
31 LED_GND LED Ground
32 LED_GND LED Ground
33 LED_GND LED Ground
34 NC No connection (Reserve)
35 LED_PWM PWM dimming signal input
36 LED_EN LED enable pin (3.3V)
37 CABC_EN CABC Enable (Reserve)
38 V_LED LED power supply 6.0V~21V
39 V_LED LED power supply 6.0V~21V
40 V_LED LED power supply 6.0V~21V
NC No connection (Reserve)
DDC Power +3.3V
EDID
DDC Clock
EDID
DDC Data
EDID
G1~G5,B0,B1
B2~B5,DE,Hsync,Vsync
www.jxlcd.com
www.jxlcd.com
R0~R5,G0
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 6
b. General Block Diagram (Rear Side)
SPEC NO.
PAGE
BT140GW03 V.A
6/29
www.jxlcd.com
www.jxlcd.com
Connector P/N :
GS13401-1110S-7H
PIN 1 PIN 40
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 7
V
2-2. Absolute Maximum Ratings
SPEC NO.
PAGE
BT140GW03 V.A
7/29
Parameter Symbol
Min. Max.
Power input voltage V
Signal input voltage V
Operating temperature T
Storage temperature T
Note 1: The relative humidity must not exceed 90% non-condensing at temperatures of 40°C or less. At
temperatures greater than 40°C, the wet bulb temperature must not exceed 39°C.
Note 2: The unit should not be exposed to corrosive chemicals.
Relative Humidity (%RH)
-30 -20 -10 0 10 20 30 40 50 60 70
100
90
80
www.jxlcd.com
70
www.jxlcd.com
60
50
40
30
20
10
0
Operation Range
Storage Range
Temperature (°C)
- 0.3 4.0 V At 25°C
CC
- 0.3 4.0 V At 25°C
IN
0 50 °C Note 1
OP
- 20 60 °C Note 2
ST
alues
Unit
Remark
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 8
2-3. Electrical Characteristics
a. Typical operating conditions
Item Symbol Min. Typ. Max. Unit Remark
SPEC NO.
PAGE
BT140GW03 V.A
8/29
Power input voltage
Permissive power input ripple
Power input current
Power consumption
Differential input high
threshold voltage
Differential input low
LVDS
interface
Color Engine Voltage
CABC Voltage Level
threshold voltage
Common input
voltage
Terminating resistor
Enable
Level
www.jxlcd.com
www.jxlcd.com
Disable
Enable
Disable
V
3 3.3 3.6 V
CC
V
- - 0.1 V
RF
I
- 260 300 mA Note 1
CC
P
- 0.85 1 Watts Note 1
C
V
- - +100 mV
LVT H
V
-100 - - mV
LVT L
V
1.0 1.2 1.4 V
LVC
R
90 100 110 ohm
T
COLOR_EN
COLOR_EN
CABC_EN
CABC_EN
2.4 -- 3.6 V
0 -- 0.8 V
2.4 -- 3.6 V
0 -- 0.8 V
LVDS
interface
Rush current
LED rush current
Note 1: The specified input current and power consumption are under the V
(frame frequency) condition whereas mosaic pattern is displayed.
Note 2: LVDS waveform diagram
Rxin+/CLK+
Rxin-/CLK-
I
- - 1.5 A Note 3
Rush
I
LED-Rush
- - 3.0 A Note 4
V
LVC
GND
=3.3 V, 25°C, f
cc
V
V
LVT H
LVT L
=60Hz
V
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 9
SPEC NO.
PAGE
BT140GW03 V.A
9/29
Note 3: Test condition
(1) Pattern: Black pattern
(2) V
= 3.3 V, V
CC
rising time = 470 μs ± 10%
CC
Control signal
(High to low)
90%
10%
V
CC
Ton=470µs±10%
(3) Test circuit
3.3 V
R1
47K
R2
www.jxlcd.com
www.jxlcd.com
12V
C3
1uF
1K
R3
47K
M1
2SK1059
C2
10000pF
M2
2SK1399
FUSE
C1
1uF
VCC ( LCD input)
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 10
_
SPEC NO.
PAGE
BT140GW03 V.A
10/29
Note 4: Test condition
(1) Pattern: LED duty 100％
(2) V_LED = 12.0V, V_LED rising time = 470
μs ± 10%
Control signal
(High to low)
90%
10%
V
LED
Ton=470µs±10%
(3) Test circuit
12 V
R1
47K
www.jxlcd.com
www.jxlcd.com
21V
C3
1uF
R2
1K
R3
47K
M1
2SK1059
C2
10000pF
M2
2SK1399
FUSE
C1
1uF
V_LED
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 11
b. Power sequence
SPEC NO.
PAGE
BT140GW03 V.A
11/29
www.jxlcd.com
www.jxlcd.com
Power sequence timing table
Parameter
t
≧0.5 -- ≦10 ms
1
t
≧0 -- ≦50 ms
2
t
≧0 -- -- ms
3
t
≧150 -- -- ms
4
t
≧200 --- -- ms
5
t
≧0 -- -- ms
6
t
≧0 -- ≦10 ms
7
t
≧0.5 -- ≦10 ms
A
t
＞0 -- -- ms
B
t
≧0 -- -- ms
C
t
≧0 -- -- ms
D
t
≧0 -- -- ms
E
t
≧0 -- -- ms
F
Min. Typ. Max.
Value
Units
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 12
c. Display color vs. input data signals
Signal Name Description Remark
SPEC NO.
PAGE
BT140GW03 V.A
12/29
R5 Red Data 5 (MSB)
R4 Red Data 4
R3 Red Data 3
R2 Red Data 2
R1 Red Data 1
R0 Red Data 0 (LSB)
Red-pixel Data
G5 Green Data 5 (MSB)
G4 Green Data 4
G3 Green Data 3
G2 Green Data 2
G1 Green Data 1
G0 Green Data 0 (LSB)
Green-pixel Data
B5 Blue Data 5 (MSB)
B4 Blue Data 4
B3 Blue Data 3
B2 Blue Data 2
Red-pixel data. Each red pixel's brightness data
consists of these 6 bits pixel data.
Green-pixel data. Each green pixel's brightness
data consists of these 6 bits pixel data.
Blue-pixel data. Each blue pixel's brightness data
consists of these 6 bits pixel data.
B1 Blue Data 1
B0 Blue Data 0 (LSB)
www.jxlcd.com
www.jxlcd.com
Blue-pixel Data
Signal for 1 DCLK cycle (t
)
CLK
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 13
d. Input signal timing
Timing table
SPEC NO.
PAGE
BT140GW03 V.A
13/29
www.jxlcd.com
www.jxlcd.com
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 14
e. Display position
D(1, 1) D(2, 1) …… D(683, 1) …… D(1365, 1) D(1366, 1)
D(1, 2) D(2, 2) …… D(683, 2) …… D(1365, 2) D(1366, 2)
.
.
.
D(1, 384) D(2, 384) …… D(683, 384) …… D(1365, 384) D(1366, 384)
.
.
.
D(1, 767) D(2, 767) …… D(683, 767) …… D(1365, 767) D(1366, 767)
D(1, 768) D(2, 768) …… D(683, 768) …… D(1365, 768) D(1366, 768)
f. Backlight driving conditions
Parameter Symbol Min. Typ. Max. Unit Remark
……
……
.
.
.
.
.
.
SPEC NO.
PAGE
……
……
BT140GW03 V.A
14/29
.
.
.
.
.
.
.
.
.
.
.
.
LED Forward Voltage V
LED Forward Current
Power consumption
Input PWM frequency F
LED life time - 15,000 Hr T = 25°C , Note 2
Note 1: PWM duty ratio linearity guarantees 20~100%
Note 2: LED life time definition is Brightness decrease to 50% of initial or abnormal lighting.
www.jxlcd.com
www.jxlcd.com
Duty ratio - 5 100 % Note 1
3 3.2 3.4 V
F
IF 20 mA
P
3.0 W
LED
190 2000 Hz T = 25°C
PWM
T = 25°C
T = 25°C
T = 25°C
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 15
g. Module function block
SPEC NO.
PAGE
BT140GW03 V.A
15/29
LED driver
Timing
www.jxlcd.com
www.jxlcd.com
controller
LED Light-bar
TFT-LCD
Source driver
Step-up regulator
& reference voltage
generator
LVDS connector
Gate driver
EDID
EEPROM
LVDS DATA BUS mini-LVDS & CONTROL BUS POWER I2C BUS
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 16
SPEC NO.
PAGE
BT140GW03 V.A
16/29
3. Optical specifications
Ambient temperature = 25°C
Item Symbol Condition
Specification
Min. Typ. Max.
Unit Remark
Response time
Contrast ratio CR
Viewing angle
Brightness
(5 points average)
Color chromaticity (CIE)
www.jxlcd.com
www.jxlcd.com
Tr+Tf θ= 0°
θ= 0°
Top
Bottom
Left
Right
170 200 nit Note 2,5
Y
L
Wx
Wy
Rx
Ry
Gx
Gy
Bx
CR≧10
CR≧10
CR≧10
CR≧10
θ= 0°
500 600 Note 2,4
15
30
40
40
-0.03
8 16 ms Note 3
deg Note 2,4,6
0.313
0.329
0.586
0.355
0.317
0.563
0.16
+0.03
Note 2,9
B
y
Color Gamut NTSC CIE1931 45 % -
δ
0.8
W(5)
White uniformity
0.6
δ
W(13)
Cross talk Ct 2% Note 8
Note 1: To be measured in dark room.
Note 2: To be measured with a viewing cone of 2°by Topcon luminance meter BM-5A.
Note 3: Definition of response time:
The output signals of BM-7 are measured when the input signals are changed from “Black” to
“White” (falling time) and from “White” to “Black” (rising time), respectively. The response time
interval is between 10% and 90% of amplitudes. Refer to figure as below.
0.144
Note 2,7
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 17
(
Avg
)
SPEC NO.
PAGE
BT140GW03 V.A
17/29
100%
S
i
90%
g
n
a
l
(
R
e
l
a
t
i
v
e
v
a
l
u
10%
e
)
0%
Note 4: Definition of contrast ratio:
Contrast ratio is calculated with the following formula:
Note 5: Driving current for LED should be 20 mA.
Note 6: Definition of viewing angle
Contrast ratio
Luminance is measured at the following thirteen points (1~13):
Y
= (Y1+ Y2+Y3+Y4 +Y5) / 5
L
www.jxlcd.com
www.jxlcd.com
Tr
of 5pts
=
"Black"
L white (Avg of 5pts.)
L
Black (Avg of 5pts.)
"White""White"
Tf
Note 7: Definition white uniformity
Luminance is measured at the following thirteen points (1~13):
δ
Minimum [ L(1) ~ L(13) ] / Maxmimum [ L(1)~L(13) ]
W(13) =
δ
W(5) =
Minimum [ L(1) ~ L(5) ] / Maxmimum [ L(1)~L(5) ]
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 18
SPEC NO.
PAGE
BT140GW03 V.A
18/29
Note 8:
1/2
A
www.jxlcd.com
www.jxlcd.com
32 gray level 32 gray level
Unit: percentage of dimension of display area
l L
l L
l / LA x 100%= 2% max., LA and L
A-LA’
l / LB x 100%= 2% max., LB’ and LB’ are brightness at location B and B’
B-LB’
1/6
B
1/6
1/2
2/3 1/3
are brightness at location A and A’
A’
1/2
A’
0 gray level
1/6
1/6
1/3
1/2
B’
2/3
Note 9: Definition of color chromaticity (CIE)
Color coordinate of White, Red, Green, Blue at center point (1).
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 19
4. Reliability test items
Test Item Test Condition Judgment Remark
SPEC NO.
PAGE
BT140GW03 V.A
19/29
High temperature storage
Low temperature storage
High temperature & high
humidity operation
High temperature operation
Low temperature operation
Thermal Shock
(Non-operation)
Electrostatic discharge (ESD)
Vibration
(Non-operation)
Mechanical shock
(Non-operation)
www.jxlcd.com
www.jxlcd.com
60°C, 240 hours
-20°C, 240 hours
50°C, 80% RH, 240 hours
(No condensation)
50°C, 240 hours
0°C, 240 hours
-20°C / 30 mins ~ 60°C / 30 mins
100 cycles
150 pF, 330Ω,
Contact: ±8kV, Air: ±15kV
1.5G / 10-500 Hz, Sine wave, 30 min/cycle,
1cycle for each X, Y, Z
220G/2ms, Half sine wave, ±X, ±Y, ±Z one
time for each direction
Note 1 Note 2
Note 1 Note 2
Note 1 Note 2
Note 1 Note 2
Note 1 Note 2
Note 1 Note 2
Note 1
Note 1 Note 2
Note 1 Note 2
Note 1: Pass: Normal display image with no obvious non-uniformity and no line defect.
Fail: No display image, obvious non-uniformity, or line defects.
Partial transformation of the module parts should be ignored.
Note 2: Evaluation should be tested after storage at room temperature for more than one hour.
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 20
SPEC NO.
PAGE
BT140GW03 V.A
20/29
5. Safety
5-1. Sharp edge requirements
There will be no sharp edges or corners on the display assembly that could cause injury.
5-2. Materials
a. Toxicity
There will be no carcinogenic materials used anywhere in the display module. If toxic materials are
used, they will be reviewed and approved by the responsible InnoLux Toxicologist.
b. Flammability
All components including electrical components that do not meet the flammability grade UL94-V0 in the
module will complete the flammability rating exception approval process. The printed circuit board will
be made from material rated 94-V0 or better. The actual UL flammability rating will be printed on the
printed circuit board.
c. Capacitors
If any polarized capacitors are used in the display assembly, provisions will be made to keep them from
being inserted backwards.
6. Display quality
The display quality of the color TFT-LCD module should be in compliance with the InnoLux
incoming inspection standard.
www.jxlcd.com
www.jxlcd.com
7. Handling precaution
(1) Do not apply rough force such as bending or twisting to the module during assembly.
(2) To assemble or install module into user’s system can be only in clean working areas. The
dust and oil may cause electrical short or worsen the polarizer.
(3) It’s not permitted to have pressure or impulse on the module because the LCD panel and
backlight will be damaged.
(4) Always follow the correct power sequence when LCD module is connecting and operating.
(5) Do not pull the I/F connector in or out while the module is operating.
(6) Do not disassemble the module.
(7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft
and easily scratched.
(8) It is dangerous that moisture come into or contacted the LCD module, because moisture may
damage LCD module when it is operating.
(9) High temperature or humidity may reduce the performance of module. Please store LCD
module within the specified storage conditions.
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 21
SPEC NO.
PAGE
BT140GW03 V.A
21/29
8. Label Definition
8-1. Module label
BT140GW03 V.A
AB1400003 A0X
X X X X X X X Y M D L N N N N
23mm
Z1 Z2 –Z3 Z4 Z5 Z6 Z7 –Z8– Z9 –Z10 –Z11 Z12– Z13–Z14 Z15– Z16– Z17 Z18 Z19–Z20 Z21 Z22 Z
23
73mm
(a) Model Number : BT140GW03 V.A
(b) Product Number : AB1400003A0X
(c) Serial ID: X X X X X X X Y M D L N N N N
(d) Production Location: MADE IN XXXX.
(e) UL/CB logo: “XXXX” especially stands for panel manufactured by CMI Ningbo satisfying UL/CB requirement.
“LEOO” “CANO” is the CMI’s UL factory code for Ningbo factory.
www.jxlcd.com
www.jxlcd.com
Serial No.
Product stroke
Year, Month, Date
CMI Internal Use
Revision
CMI Internal Use
(5) Serial ID II (CMI Internal Use):
Z1 Z2 –Z3 Z4 Z5 Z6 Z7 –Z8– Z9 –Z10 –Z11 Z12– Z13–Z14 Z15– Z16– Z17 Z18 Z19–Z20 Z21 Z22 Z
XXXX
MADE IN CHINA
23
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 22
8-2. Carton label
(1) Model No. : BT140GW03
(2) Version: V.A
(3) Package Quantity :XXPCS
(4) Serial ID: X X X X X X X Y M D L N N N
M
BOX ID:
Model No. BT140GW03 V.A AB1400003 A0X
Quantity: XX PCS
MFG Date: XXXX/XX/XX
QC:
MADE IN CHINA
www.jxlcd.com
www.jxlcd.com
INNOLUX DISPLAY
X X X X X X X Y M D L N N N
90.5mm
55mm
SPEC NO.
PAGE
Serial No.
Product stroke
Year, Month, Date
CMI Internal Use
Revision
CMI Internal Use
BT140GW03 V.A
22/29
20mm
53.5mm
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 23
9. Packing Form
SPEC NO.
PAGE
BT140GW03 V.A
23/29
www.jxlcd.com
www.jxlcd.com
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 24
10. Mechanical Drawings
10-1 Front Side
SPEC NO.
PAGE
BT140GW03 V.A
24/29
www.jxlcd.com
www.jxlcd.com
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 25
10-2 Rear side
SPEC NO.
PAGE
BT140GW03 V.A
25/29
www.jxlcd.com
www.jxlcd.com
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 26
Appendix: EDID Code
SPEC NO.
PAGE
BT140GW03 V.A
26/29
Byte
(Hex)
Header
00
Header
01
Header
02
Header
03
Header
04
Header
Header
05
Header
06
Header
07
EISA manufacture code ( 3 Character ID ) " LEN"
08
EISA manufacture code (Compressed ASCⅡ)
09
Panel Supplier Reserved - Product Code "14" 16:9 HD 1366x768 LED B/L"
0A
Panel Supplier Reserved - Product Code
0B
ID Serial Number (32-bit serial number)
0C
ID Serial Number (32-bit serial number)
0D
ID Serial Number (32-bit serial number)
0E
ID Serial Number (32-bit serial number)
0F
Week of Manufacture 00 weeks
10
EDID Version
Vendor / Product
Year of Manufacture 2010 years
11
12
13
14
15
16
Display
17
Parameters
18
19
1A
1B
1C
1D
1E
1F
20
21
Panel Color Coordinates
22
www.jxlcd.com
www.jxlcd.com
EDID structure version # = 1
EDID revision # = 3
Video input Definition = Digital signal
Max H image size (Rounded cm) = 31 cm
Max V image size (Rounded cm) = 18 cm
Display gamma = (gamma*100)-100 = Example:(2.2*100)-100=120 = 2.2 Gamma
Feature Support (Standby,Suspend,Active Off/Very Low Power, RGB color
display,Preferred Timing Mode)
Red/Green Low Bits (RxRy/GxGy)
Blue/White Low Bits (BxBy/WxWy)
Red X Rx = 0.580
Red Y Ry = 0.340
Green X Gx = 0.310
Green Y Gy = 0.548
Blue X Bx = 0.155
Blue Y By = 0.155
White X Wx = 0.313
White Y Wy = 0.329
Field Name and Comments
Value
(Hex)
00
FF
FF
FF
FF
FF
FF
00
30
AE
A0
40
00
00
00
00
00
14
01
03
80
1F
12
78
EA
87
F5
94
57
4F
8C
27
27
50
54
Value
(Bin)
00000000
11111111
11111111
11111111
11111111
11111111
11111111
00000000
00110000
10101110
10100000
01000000
00000000
00000000
00000000
00000000
00000000
00010100
00000001
00000011
10000000
00011111
00010010
01111000
11101010
10000111
11110101
10010100
01010111
01001111
10001100
00100111
00100111
01010000
01010100
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 27
SPEC NO.
PAGE
BT140GW03 V.A
27/29
Established timing 1 (00h if not used)
23
Established timing 2 (00h if not used)
24
Timings
Established
Standard Timing ID
Timing Descriptor #1
Manufacturer's timings (00h if not used)
25
Standard timing ID1 (01h if not used)
26
Standard timing ID1 (01h if not used)
27
Standard timing ID2 (01h if not used)
28
Standard timing ID2 (01h if not used)
29
Standard timing ID3 (01h if not used)
2A
Standard timing ID3 (01h if not used)
2B
Standard timing ID4 (01h if not used)
2C
Standard timing ID4 (01h if not used)
2D
Standard timing ID5 (01h if not used)
2E
Standard timing ID5 (01h if not used)
2F
Standard timing ID6 (01h if not used)
30
Standard timing ID6 (01h if not used)
31
Standard timing ID7 (01h if not used)
32
Standard timing ID7 (01h if not used)
33
Standard timing ID8 (01h if not used)
34
Standard timing ID8 (01h if not used)
35
36
37
38
39
3A
3B
3C
3D
3E
3F
40
41
42
43
44
45
46
47
www.jxlcd.com
www.jxlcd.com
Pixel Clock/10,000 (LSB) 69.3 MHz @ 60Hz
Pixel Clock/10,000 (MSB)
Horizontal Active (lower 8 bits) 1366 Pixels
Horizontal Blanking(Thp-HA) (lower 8 bits) 100 Pixels
Horizontal Active / Horizontal Blanking(Thp-HA) (upper 4:4bits)
Vertical Avtive 768 Lines
Vertical Blanking (Tvp-HA) (DE Blanking typ.for DE only panels) 20 Lines
Vertical Active : Vertical Blanking (Tvp-HA) (upper 4:4bits)
Horizontal Sync. Offset (Thfp) 48 Pixels
Horizontal Sync Pulse Width (HSPW) 32 Pixels
Vertical Sync Offset(Tvfp) : Sync Width (VSPW) 1 Lines : 4 Lines
Horizontal Vertical Sync Offset/Width (upper 2bits)
Horizontal Image Size (mm) 309 mm
Vertical Image Size (mm) 174 mm
Horizontal Image Size / Vertical Image Size
Horizontal Border = 0 (Zero for Notebook LCD)
Vertical Border = 0 (Zero for Notebook LCD)
Non-Interlace, Normal display, no stereo, Digital Separate ( Non-interlaced,Normal
display,no stereo,Vertical Polarity Negative,Horizontal Polarity Negative)
00
00
00
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
12
1B
56
64
50
00
14
30
30
20
14
00
35
AE
10
00
00
18
00000000
00000000
00000000
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00010010
00011011
01010110
01100100
01010000
00000000
00010100
00110000
00110000
00100000
00010100
00000000
00110101
10101110
00010000
00000000
00000000
00011000
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 28
Pixel Clock/10,000 (LSB) 60.44 MHz @ 50Hz
48
Pixel Clock/10,000 (MSB)
49
Horizontal Active (lower 8 bits) 1366 Pixels
4A
Horizontal Blanking(Thp-HA) (lower 8 bits) 168 Pixels
4B
Horizontal Active / Horizontal Blanking(Thp-HA) (upper 4:4bits)
4C
Vertical Avtive 768 Lines
4D
Vertical Blanking (Tvp-HA) (DE Blanking typ.for DE only panels) 20 Lines
4E
Vertical Active : Vertical Blanking (Tvp-HA) (upper 4:4bits)
4F
Horizontal Sync. Offset (Thfp) 48 Pixels
50
Horizontal Sync Pulse Width (HSPW) 32 Pixels
51
Vertical Sync Offset(Tvfp) : Sync Width (VSPW) 1 Lines : 4 Lines
52
Horizontal Vertical Sync Offset/Width (upper 2bits)
53
Horizontal Image Size (mm) 309 mm
54
Timing Descriptor #2
Vertical Image Size (mm) 174 mm
55
Horizontal Image Size / Vertical Image Size
56
Horizontal Border = 0 (Zero for Notebook LCD)
57
Vertical Border = 0 (Zero for Notebook LCD)
58
Non-Interlace, Normal display, no stereo, Digital Separate ( Non-interlaced,Normal
59
display,no stereo,Vertical Polarity Negative,Horizontal Polarity Negative)
Flag
5A
Flag
5B
Flag
5C
5D
5E
5F
60
61
62
63
64
65
Timing Descriptor #3
66
67
68
69
6A
6B
www.jxlcd.com
www.jxlcd.com
Data Type Tag ( ASCII String )
Flag
(Horizontal active pixel / 8) - 31 "1368"
Image Aspect Ratio "16 : 9"
Middle Refresh Rate "50Hz"
(Horizontal active pixel / 8) - 31 "1368"
Image Aspect Ratio "16 : 9"
Low Refresh Rate "40Hz"
Brightness (1/10nit) "220" nit
Feature flag " TN, White LED Backlight "
Reserved
LCD Supplier manufacture Code (3 character ID) "CMI"
LCD Supplier manufacture Code (3 character ID)
LCD Supplier Product code
LCD Supplier Product code
SPEC NO.
PAGE
BT140GW03 V.A
28/29
10011100
9C
00010111
17
01010110
56
10101000
A8
01010000
50
00000000
00
00010100
14
00110000
30
00110000
30
00100000
20
00010100
14
00000000
00
00110101
35
10101110
AE
00010000
10
00000000
00
00000000
00
00011000
18
00000000
00
00000000
00
00000000
00
00000000
00
00000000
00
10001100
8C
00001001
09
00110010
32
10001100
8C
00001001
09
00101000
28
00010110
16
00001001
09
00000000
00
00001101
0D
10101001
A9
00000000
00
00000000
00
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Page 29
SPEC NO.
PAGE
BT140GW03 V.A
29/29
Flag
6C
Flag
6D
Flag
6E
Data Type Tag ( Monitor Name, stored as ASCII )
6F
Flag
70
Model Name, stored as ASCII "B"
71
Model Name, stored as ASCII "T"
72
Model Name, stored as ASCII "1"
73
Model Name, stored as ASCII "4"
74
Model Name, stored as ASCII "0"
75
Model Name, stored as ASCII "G"
76
Model Name, stored as ASCII "W"
77
Timing Descriptor #4
Model Name, stored as ASCII "0"
78
Model Name, stored as ASCII "3"
79
Model Name, stored as ASCII "V"
7A
Model Name, stored as ASCII "A"
7B
Model Name, stored as ASCII
7C
Model Name, stored as ASCII
7D
Extension flag (# of optional 128 panel ID extension block to follow, Typ = 0)
7E
00
00
00
FE
00
42
54
31
34
30
47
57
30
33
56
41
0A
20
00
00000000
00000000
00000000
11111110
00000000
01000010
01010100
00110001
00110100
00110000
01000111
01010111
00110000
00110011
01010110
01000001
00001010
00100000
00000000
www.jxlcd.com
www.jxlcd.com
Check Sum (The 1-byte sum of all 128 bytes in this panel ID block shall = 0)
7F
F7
11100111
Checksum
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFOR MED TO ANY OTHE R FORMS WITHOUT PERMI SSION FROM Chimei-Innolux.
Loading...