INNOLUX DISPLAY CORPORATION
BT101IW03 V.1 LCD MODULE SPECIFICATION
( ) Preliminary Specification
(●) Final Specification
Customer Checked & Approved by
SEC
Approved by Checked by Prepared by
MKT PD PM
www.jxlcd.com
www.jxlcd.com
Innolux Display Corporation
No.160 Kesyue Rd., Chu-Nan Site, Hsinchu Science Park,
Chu-Nan 350, Miao-Li County, Taiwan
Annie Lu
Date: 2009/12/04
Tel: 886-37-586000 Fax: 886-37-586060
Version: 0.2
Record of Revision
Version Revise Date Page Content
InnoLux copyright
All rights reserved,
Copying forbidden.
0.0 2009/08/06
0.1 2009/08/21
0.2 2009/12/04
www.jxlcd.com
www.jxlcd.com
All First Edition issued
1 Add LED usage information: 27EA
13 Add LED circuit block information
23 Change EDID Freq. to 54.2MHz
Contents: Page
SPEC NO.
PAGE
BT101IW03 V.1
1/ 27
1 . General Specifications
2 . Electrical Specifications
2-1 Pin Assignment
2-2 Absolute Maximum Ratings
2-3 Electrical Characteristics
3 . Optical Specifications
4. Reliability Test Items
5. Safety
6. Display Quality
7. Handling Precaution
8. Label Definition
2
3
5
6
12
15
16
16
16
18
9. Packing Form
10. Mechanical Drawings
Appendix
www.jxlcd.com
www.jxlcd.com
19
21
23
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
1. General Specifications
NO. Item Specification Unit
1 Display resolution (pixel) 1024(H) X 600(V), SD resolution
SPEC NO.
PAGE
BT101IW03 V.1
2/ 27
2 Active area
3 Screen size 10.1 inches diagonal Inches
4 Pixel pitch 217.5x208.8 um
5 Color configuration R, G, B vertical stripe
6 Overall dimension
7 Weight
8 Surface treatment Anti-glare
9 Input color signal 6 bit LVDS
10 Display colors 262K (6 bit)
11 Optimum viewing direction 6 o’clock
12 Backlight W-LED
13 RoHS RoHS compliance
www.jxlcd.com
www.jxlcd.com
222.72(H) X 125.28(V)
235 (W) X 143(H) X 5.2(D) (max)
190Max.
mm
mm
Grams
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
2. Electrical Specifications
2-1 Pin Assignment
a. Panel connector
Connector Part No.: I-PEX 20455-040E or equivalent
User’s connector Part No: I-PEX 20453-040T-11 or equivalent
PIN NO Symbol Description Remark
1 DIAG_LOOP Plug detection pin
2 VCC Power Supply (+3.3V)
3 VCC Power Supply (+3.3V)
4 V
5 BIST BIST function enable (+3.3V)
6 Clk
7 DATA
8 Rxin0- Differential Data Input
9 Rxin0+ Differential Data Input
10 GND Ground
11 Rxin1- Differential Data Input
12 Rxin1+ Differential Data Input
13 GND Ground
14 Rxin2- Differential Data Input
15 Rxin2+ Differential Data Input
16 GND Ground
17 CLK- Differential Clock Input
18 CLK+ Differential Clock Input
19 NC No connection (Reserve)
20 NC No connection (Reserve)
21 NC No connection (Reserve)
22 NC No connection (Reserve)
23 NC No connection (Reserve)
24 NC No connection (Reserve)
25 NC No connection (Reserve)
26 NC No connection (Reserve)
27 NC No connection (Reserve)
28 NC No connection (Reserve)
29 NC No connection (Reserve)
30 NC No connection (Reserve)
31 LED_GND LED Ground
32 LED_GND LED Ground
33 LED_GND LED Ground
34 DIAG_LOOP Plug detection pin
35 LED_PWM PWM dimming signal input
36 LED_EN LED enable pin (3.3V)
37 NC No connection (Reserve)
38 V_LED LED power supply 6.0V~20V
39 V_LED LED power supply 6.0V~20V
40 V_LED LED power supply 6.0V~20V
DDC Power +3.3V
EDID
DDC Clock
EDID
DDC Data
EDID
www.jxlcd.com
www.jxlcd.com
SPEC NO.
PAGE
BT101IW03 V.1
3/ 27
R0~R5,G0
G1~G5,B0,B1
B2~B5,DE,Hsync,Vsync
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
b. General Block Diagram
VR
DC/DC
DC/DC
www.jxlcd.com
www.jxlcd.com
20455-040
Pin1
T-CON
Connector plug in direction
SPEC NO.
PAGE
BT101IW03 V.1
4/ 27
FPC
LED
Driver
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
V
2-2. Absolute Maximum Ratings
SPEC NO.
PAGE
BT101IW03 V.1
5/ 27
alues
Parameter Symbol
Power input voltage VCC - 0.3 4.0 V At 25°C
Input signal voltage VIN - 0.3 4.0 V At 25°C
LED input voltage V
Operating temperature Top 0 50 °C Note 1
Storage temperature TST - 20 60 °C Note 2
Re-screw - 5 Times
Assured torque at side mount - 2 kgf.cm
Note 1: The relative humidity must not exceed 90%, non-condensing at temperatures of 40°C or
less. At temperatures greater than 40°C, the wet bulb temperature must not exceed 39°C.
Note 2: The unit should not be exposed to corrosive chemicals.
Relative Humidity (%RH)
-40 -20 0 20 40 60 80
www.jxlcd.com
www.jxlcd.com
100
90
80
70
60
50
40
30
20
10
Operation Range
Storage Range
0
Temperature (°C)
- 0.3 30 V At 25℃
LED
Min. Max.
Unit
Remark
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
2-3. Electrical Characteristics
a. Typical operating conditions
Item Symbol Min. Typ. Max. Unit Remark
SPEC NO.
PAGE
BT101IW03 V.1
6/ 27
Power input voltage V
Permissive power input ripple
Power input current I
Power consumption
Differential input high
threshold voltage
Differential input low
LVDS
interface
Note 1: The specified input current and power consumption are under the V
Note 2: LVDS waveform diagram
Rxin+/CLK+
Rxin-/CLK-
threshold voltage
Common input
voltage
Terminating resistor
Rush current
LED rush current
f
=60Hz (frame frequency) condition whereas black pattern is displayed.
www.jxlcd.com
V
www.jxlcd.com
3 3.3 3.6 V
CC
V
- - 0.1 V
RF
- 220 400 mA Note 1
CC
P
- 2.75 (3.15) Watts Note 1
c
V
- - +100 mV
LVT H
V
-100 - - mV
LVT L
V
1.0 1.2 1.4 V Note 2
LVC
R
90 100 110 ohm
T
I
- - 1 A Note 3
Rush
I
LED-Rush
- - 2.0 A Note 4
V
LVC
V
LVC
=3.3 V, 25°C,
cc
=1.2V,
Note 2
=1.2V,
Note 2
V
LVT H
V
LVT L
V
LVC
GND
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
SPEC NO.
PAGE
BT101IW03 V.1
7/ 27
Note 3: Test condition
(1) Pattern: Black pattern
(2) V
= 3.3 V, VCC rising time = 470 μs ± 10%
CC
Control signal
(High to low)
90%
10%
V
CC
Ton=470µs±10%
(3) Test circuit
3.3 V
R1
47K
R2
www.jxlcd.com
www.jxlcd.com
12V
C3
1uF
1K
R3
47K
M1
2SK1059
C2
10000pF
M2
2SK1399
FUSE
C1
1uF
VCC ( LCD input)
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
_
SPEC NO.
PAGE
BT101IW03 V.1
8/ 27
Note 4: Test condition
(1) LED duty 100％
(2) V_LED = 12.0V, V_LED rising time = 470
μs ± 10%
Control signal
(High to low)
90%
10%
V
LED
Ton=470µs±10%
(3) Test circuit
12 V
R1
47K
R2
www.jxlcd.com
www.jxlcd.com
21V
C3
1uF
1K
R3
47K
M1
2SK1059
C2
10000pF
M2
2SK1399
FUSE
C1
1uF
V_LED
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
b. Power sequence
SPEC NO.
PAGE
BT101IW03 V.1
9/ 27
Power supply for LCD, VCC
Interface data signal, V
(LVDS signal of transmitter)
Backlight on/off
Power sequence timing table
Parameter
T1 0.5 - 10 ms
T2 0 - 50 ms
T3 200 - - ms
i
Min. Typ. Max.
90%
10%
0V
T
T
1
2
0V
OFF OFF
Value
Valid Data
T
3
T
Backlight
On
90%
10%
T
T6
T
5
4
7
Units
T4 200 - - ms
www.jxlcd.com
T5 0 - 50 ms
www.jxlcd.com
T6 0 - 10 ms
T7 400 - - ms
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
c. Display color vs. input data signals
Signal Name Description Remark
SPEC NO.
PAGE
BT101IW03 V.1
10/ 27
R5 Red Data 5 (MSB)
R4 Red Data 4
R3 Red Data 3
R2 Red Data 2
R1 Red Data 1
R0 Red Data 0 (LSB)
Red-pixel Data
G5 Green Data 5 (MSB)
G4 Green Data 4
G3 Green Data 3
G2 Green Data 2
G1 Green Data 1
G0 Green Data 0 (LSB)
Green-pixel Data
B5 Blue Data 5 (MSB)
B4 Blue Data 4
B3 Blue Data 3
B2 Blue Data 2
Red-pixel data. Each red pixel's brightness data
consists of these 6 bits pixel data.
Green-pixel data. Each green pixel's brightness
data consists of these 6 bits pixel data.
Blue-pixel data. Each blue pixel's brightness data
consists of these 6 bits pixel data.
B1 Blue Data 1
B0 Blue Data 0 (LSB)
www.jxlcd.com
www.jxlcd.com
Blue-pixel Data
Signal for 1 DCLK cycle (t
CLK
)
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
d. Input signal timing
Timing table
Description Symbol Min Typ Max Unit
Frame rate -- --- 60 --- Hz
SPEC NO.
PAGE
BT101IW03 V.1
11/ 27
Clock freq. 1/t
Line cycle time tH (1054) 1440 (1600)
Line width-active tHd --- 1024 ---
Frame cycle time tV (610) 628 (680) tH
V width-active tVd --- 600 --- tH
DE
DE
DCLK
www.jxlcd.com
www.jxlcd.com
t
CLK
(40) 54.2 (60) MHz
CLK
t
V
t
Vd
t
H
t
Hd
t
CLK
t
CLK
e. Display position
D(1, 1) D(2, 1) …… D(673, 1) …… D(1023, 1) D(1024, 1)
D(1, 2) D(2, 2) …… D(673, 2) …… D(1023, 2) D(1024, 2)
.
.
.
D(1, 384) D(2, 300) …… D(673, 384) …… D(1023, 300) D(1024, 300)
.
.
.
D(1, 767) D(2, 599) …… D(673, 599) …… D(1023, 599) D(1024, 599)
D(1, 768) D(2, 600) …… D(673, 600) …… D(1023, 600) D(1024, 600)
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
……
……
.
.
.
.
.
.
……
……
.
.
.
.
.
.
.
.
.
.
.
.
f. Backlight driving conditions
Parameter Symbol Min. Typ. Max. Unit Remark
SPEC NO.
PAGE
BT101IW03 V.1
12/ 27
LED Forward Voltage V
LED Forward Current
LED Power consumption
Output PWM frequency F
Duty ratio - 5 100 % Note 1, 2
LED Life Time (LED only) - 15,000 Hr T = 25°C , Note 3
Note 1: The BL power consumption @100 nits with full white pattern under the V
C, f
=60Hz (frame frequency) condition
V
Note 2: PWM duty cycle linearity guarantees 20~100%.
Note 3: LED life time definition is brightness decrease to 50% of initial or abnormal lighting.
g. Module function block
www.jxlcd.com
www.jxlcd.com
LED driver
Timing
controller
3 3.2 3.4 V
F
IF 20 mA
P
2.1 (2.3) W
LED
200 1000 2000 Hz T = 25°C, Note 1, 2
PWM
LED Light-bar
TFT-LCD
Source driver
Step-up regulator
& reference voltage
generator
EEPROM
LVDS connector
T = 25°C, Note 1, 2
rms
T = 25°C, Note 1, 2
rms
T = 25°C, Note 1, 2
=3.3 V, 25 °
cc
Gate driver
EDID
LVDS DATA BUS mini-LVDS & CONTROL BUS POWER I2C BUS
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
h. LED circuit block
SPEC NO.
PAGE
BT101IW03 V.1
13/ 27
LED Driving
Circuit
LED_P
3 parallels
& 9 series
www.jxlcd.com
www.jxlcd.com
FB1
FB2
FB3
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
3. Optical specifications
SPEC NO.
PAGE
BT101IW03 V.1
14/ 27
Item Symbol Condition
Response time
Contrast ratio CR
Viewing angle
Brightness
(5 points average)
Color chromaticity (CIE)
Specification
Min. Typ. Max.
Tr+Tf θ= 0∘
θ= 0∘
Top 15
Bottom 30
CR≧10
Left 40
Right
Y
170 200 nit Note 2,5
L
Wx
Wy
Rx
Ry
Gx
θ= 0∘
400 500 Note 2,4
40
-0.03
8 16 ms Note 3
0.313
0.329
0.575
0.348
+0.03
0.336
Unit Remark
deg Note 2,4,6
Note 2
Gy
www.jxlcd.com
www.jxlcd.com
Color Gamut NTSC CIE1931 40 45 % -
White uniformity δ
Cross talk Ct 2% Note 8
Note 1: To be measured in dark room.
Note 2: To be measured with a viewing cone of 2°by Topcon luminance meter BM-5A.
Note 3: Definition of response time:
The output signals of BM-7 are measured when the input signals are changed from “Black” to
“White” (falling time) and from “White” to “Black” (rising time), respectively. The response time
interval is between 10% and 90% of amplitudes. Refer to figure as below.
Bx
B
y
(1.55) Note 2,7
W(13)
0.574
0.154
0.105
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
(
Avg
)
SPEC NO.
PAGE
BT101IW03 V.1
15/ 27
100%
S
i
90%
g
n
a
l
(
R
e
l
a
t
i
v
e
v
a
l
u
10%
e
)
0%
Note 4: Definition of contrast ratio:
Contrast ratio is calculated with the following formula:
Note 5: Driving current for LED should be 20 mA.
Note 6: Definition of viewing angle
Contrast ratio
Luminance are measured at the following thirteen points (1~13):
= (Y5+Y10+Y11+Y12+Y13) / 5
Y
L
Tr
of 5pts
L white (Avg of 5pts.)
=
L
"Black"
Black (Avg of 5pts.)
"White""White"
Tf
www.jxlcd.com
www.jxlcd.com
Note 7: Definition white uniformity:
Luminance is measured at the following thirteen points (1~13):
δ
W(13) =
δ
W(5) =
Maximum Brightness of thirteen points
Minimum Brightness of thirteen points
Maximum Brightness of five points
Minimum Brightness of five points
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
13 point measuring locations refer to the point 1,~13.
5 point measuring locations refer to the point 5,10~13.
L and W are active area dimensions. Active area center refer to attached drawing
SPEC NO.
PAGE
BT101IW03 V.1
16/ 27
Note 8:
32 gray level 32 gray level
Unit: percentage of dimension of display area
l L
l L
1/2
A
www.jxlcd.com
www.jxlcd.com
l / LA x 100%= 2% max., LA and L
A-LA’
l / LB x 100%= 2% max., LB’ and LB’ are brightness at location B and B’
B-LB’
B
1/6
1/6
1/2
2/3 1/3
are brightness at location A and A’
A’
1/2
A’
0 gray level
1/6
1/6
1/3
1/2
B’
2/3
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
4. Reliability test items
Test Item Test Condition Judgment Remark
SPEC NO.
PAGE
BT101IW03 V.1
17/ 27
High temperature storage
Low temperature storage
High temperature & high
humidity operation
High temperature operation 50°C, 240 hours Note 1 Note 2
Low temperature operation 0°C, 240 hours Note 1 Note 2
Thermal Shock
(Non-operation)
Electrostatic discharge (ESD)
Vibration
(Non-operation)
Mechanical shock
(Non-operation)
Note 1: Pass: Normal display image with no obvious non-uniformity and no line defect.
Fail: No display image, obvious non-uniformity, or line defects.
Note 2: Evaluation should be tested after storage at room temperature more than one hour.
www.jxlcd.com
www.jxlcd.com
Partial transformation of the module parts should be ignored.
60°C, 240 hours
-20°C, 240 hours
40°C, 90% RH, 240 hours
(No condensation)
-25°C / 30 mins ~ 65°C / 30 mins
100 cycles
150 pF, 330Ω,
Contact: ±8kV, Air: ±15kV
1.5Grms, (PSD: 0.0046^G/Hz) 10 to 500
Hz random; 0.5hr for each perpendicular
axes ( X, Y, Z ).
220G/2ms, Half sine wave, ±X, ±Y, ±Z one
time for each direction
Note 1 Note 2
Note 1 Note 2
Note 1 Note 2
Note 1 Note 2
Note 1
Note 1 Note 2
Note 1 Note 2
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
5. Safety
5-1. Sharp edge requirements
There will be no sharp edges or corners on the display assembly that could cause injury.
5-2. Materials
a. Toxicity
There will be no carcinogenic materials used anywhere in the display module. If toxic materials
are used, they will be reviewed and approved by the responsible InnoLux Toxicologist.
b. Flammability
All components including electrical components that do not meet the flammability grade UL94-V0
in the module will complete the flammability rating exception approval process. The printed circuit
board will be made from material rated 94-V0 or better. The actual UL flammability rating will be
printed on the printed circuit board.
SPEC NO.
PAGE
BT101IW03 V.1
18/ 27
c. Capacitors
If any polarized capacitors are used in the display assembly, provisions will be made to keep
them from being inserted backwards.
6. Display quality
The display quality of the color TFT-LCD module should be in compliance with the InnoLux
incoming inspection standard.
www.jxlcd.com
www.jxlcd.com
7. Handling precaution
(1) Do not apply rough force such as bending or twisting to the module during assembly.
(2) To assemble or install module into user’s system can be only in clean working areas. The
dust and oil may cause electrical short or worsen the polarizer.
(3) It’s not permitted to have pressure or impulse on the module because the LCD panel and
Backlight will be damaged.
(4) Always follow the correct power sequence when LCD module is connecting and
operating.
(5) Do not pull the I/F connector in or out while the module is operating.
(6) Do not disassemble the module.
(7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is
very soft and easily scratched.
(8) It is dangerous that moisture come into or contacted the LCD module, because moisture
may damage LCD module when it is operating.
(9) High temperature or humidity may reduce the performance of module. Please store LCD
module within the specified storage conditions.
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
X
SPEC NO.
PAGE
BT101IW03 V.1
19/ 27
8. Label Definition
8-1. Module label
BT101IW03 V.1 AB1010003 10X
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
Z1 Z2 –Z3 Z4 Z5 Z6 Z7 –Z8– Z9 –Z10 –Z11 Z12– Z13–Z14 Z15– Z16– Z17 Z18 Z19–Z20 Z21 Z22 Z23
(a) Model Number : BT101IW03
(b) Product Number : AB101000310X
(c) Serial ID I (INL Internal Use):
(d) Serial ID II (INL Internal Use):
Z1Z2Z3Z4Z5Z6 –Z7 –Z8Z9Z10Z11Z
Z
Z2 Z3 Z4 Z 5 Z
1
www.jxlcd.com
www.jxlcd.com
Serial ID includes the information as below:
Manufactured Date: Year: 0~9, for 2000~2009
Month: 1~9 & A~C for Jan.~Dec.
Date: 1~9 & A~Z (exclude I, O, Q, U) for 1th~31th
Serial No.: Module manufactures sequential number.
Z1 Z2 –Z3 Z4 Z5 Z6 Z7 –Z8– Z9 –Z10 –Z11 Z12– Z13–Z14 Z15– Z16– Z17 Z18 Z19–Z20 Z21 Z22 Z23
12
73mm
- Z 7 - Z
6
Z
8
9 Z10
INNOLU
MADE IN CHINA
Z
Z
12
11
Serial Number
INL internal use
INL internal use
INL internal use
Year, Month, Date.
INL internal use
TM
18mm
8-2. Carton label
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
BOX ID:
Part No. LK.1010N.001
Model No. BT101IW03 V.1 AB1010003 101
Quantity: XX PCS
MFG Date: XXXX/XX/XX
QC:
MADE IN CHINA
(a) Model No. : BT101IW03 V.1
(b) Package Quantity:
(c) Serial ID :
www.jxlcd.com
www.jxlcd.com
Z
1 Z2 Z3 Z4
Serial ID includes the information as below:
→Manufactured Date:
Year: 0~9, for 2000~2009;
Month: 1~9 & A~C for Jan. ~Dec.;
Date: 1~9 & A~V (exclude I, O, Q, U) for 1st~31st.
→Serial Number: Module packing sequence number
– Z5 – Z6 Z7 Z8 Z
INNOLUX DISPLAY
Z1 Z2 Z3 Z4– Z5 –Z6 Z7 Z8 Z9
XX PCS
78mm
9
Serial Number
INL Internal Use
Manufactured Date
INL Internal Use
SPEC NO.
PAGE
BT101IW03 V.1
20/ 27
9. Packing Form
SPEC NO.
PAGE
BT101IW03 V.1
21/ 27
www.jxlcd.com
www.jxlcd.com
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
10. Mechanical drawings
10-1. Front Side
SPEC NO.
PAGE
BT101IW03 V.1
22/ 27
www.jxlcd.com
www.jxlcd.com
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
10-2. Rear Side
SPEC NO.
PAGE
BT101IW03 V.1
23/ 27
www.jxlcd.com
www.jxlcd.com
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
Appendix: EDID Code
Byte Value Value
Header
(hex)
0 Header 00 00000000
1 Header FF 11111111
2 Header FF 11111111
3 Header FF 11111111
4 Header FF 11111111
5 Header FF 11111111
6 Header FF 11111111
7 Header 00 00000000
8 EISA manufacture code ( 3 Character ID ) " INL" 25 00100101
EISA manufacture code (Compressed ASCⅡ)
9
0A Panel Supplier Reserved - Product Code "11" 0D 00010001
0B ( Hex. LSB first ) 00 00000000
Field Name and Comments
SPEC NO.
PAGE
BT101IW03 V.1
24/ 27
(hex) (binary)
CC 11001100
Display
Vendor / Product EDID Version
0C LCD Module Serial No - Preferred but Optional ("0" If not used) 00 00000000
0D LCD Module Serial No - Preferred but Optional ("0" If not used) 00 00000000
0E LCD Module Serial No - Preferred but Optional ("0" If not used) 00 00000000
0F LCD Module Serial No - Preferred but Optional ("0" If not used) 00 00000000
10 Week of Manufacture 00 weeks 00 00000000
11 Year of Manufacture 2009 years 13 00010011
www.jxlcd.com
12 EDID structure version # = 1 01 00000001
www.jxlcd.com
13 EDID revision # = 3 03 00000011
14 Video input Definition = Digital signal 80 10000000
15 Max H image size (Rounded cm) = 22 cm 16 00010110
16 Max V image size (Rounded cm) = 12 cm 0C 00001100
17 Display gamma “2.2” 78 01111000
Parameters
18
19 Red/Green Low Bits (RxRy/GxGy) 40 01000000
1A Blue/White Low Bits (BxBy/WxWy) 85 10000101
1B Red X Rx = 0.575 93 10010011
1C Red Y Ry = 0.348 59 01011001
Feature Support (no_DPMS, no_Active Off/Very Low Power, RGB color
display, Timing BLK 1,no_ GTF)
0A 00001010
1D Green X Gx = 0.336 56 01010110
1E Green Y Gy = 0.574 93 10010011
Panel Color
Coordinates
Timings
Established
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
1F Blue X Bx = 0.154 27 00100111
20 Blue Y By = 0.105 1B 00011011
21 White X Wx = 0.313 50 01010000
22 White Y Wy = 0.329 54 01010100
23 Established timing 1 (00h if not used) 00 00000000
24 Established timing 2 (00h if not used) 00 00000000
Standard Timing ID
25 Manufacturer's timings (00h if not used) 00 00000000
26 Standard timing ID1 (01h if not used) 01 00000001
27 Standard timing ID1 (01h if not used) 01 00000001
28 Standard timing ID2 (01h if not used) 01 00000001
29 Standard timing ID2 (01h if not used) 01 00000001
2A Standard timing ID3 (01h if not used) 01 00000001
2B Standard timing ID3 (01h if not used) 01 00000001
2C Standard timing ID4 (01h if not used) 01 00000001
2D Standard timing ID4 (01h if not used) 01 00000001
2E Standard timing ID5 (01h if not used) 01 00000001
2F Standard timing ID5 (01h if not used) 01 00000001
30 Standard timing ID6 (01h if not used) 01 00000001
31 Standard timing ID6 (01h if not used) 01 00000001
32 Standard timing ID7 (01h if not used) 01 00000001
SPEC NO.
PAGE
BT101IW03 V.1
25/ 27
Timing Descripter #1
33 Standard timing ID7 (01h if not used) 01 00000001
34 Standard timing ID8 (01h if not used) 01 00000001
35 Standard timing ID8 (01h if not used) 01 00000001
36 Pixel Clock/10,000 (LSB) 54.2 MHz @ 60Hz 2C 00101100
37 Pixel Clock/10,000 (MSB) 15 00010101
38 Horizontal Active (lower 8 bits) 1024 Pixels 00 00000000
39 Horizontal Blanking(Thp-HA) (lower 8 bits) 378 Pixels 7A 01111010
www.jxlcd.com
3A Horizontal Active / Horizontal Blanking(Thp-HA) (upper 4:4bits) 41 01000001
www.jxlcd.com
3B Vertical Avtive 600 Lines 58 01011000
3C
3D Vertical Active : Vertical Blanking (Tvp-HA) (upper 4:4bits) 20 00100000
3E Horizontal Sync. Offset (Thfp) 48 Pixels 30 00110000
3F Horizontal Sync Pulse Width (HSPW) 32 Pixels 20 00100000
40 Vertical Sync Offset(Tvfp) : Sync Width (VSPW) 3 Lines : 6 Lines 36 00110110
41 Horizontal Vertical Sync Offset/Width (upper 2bits) 00 00000000
42 Horizontal Image Size (mm) 222 mm DE 11011110
43 Vertical Image Size (mm) 125 mm 7D 01111101
Vertical Blanking (Tvp-HA) (DE Blanking typ.for DE only panels)
44 Lines
2C 00101100
44 Horizontal Image Size / Vertical Image Size 00 00000000
45 Horizontal Border = 0 (Zero for Notebook LCD) 00 00000000
46 Vertical Border = 0 (Zero for Notebook LCD) 00 00000000
Non-Interlace, Normal display, no stereo, Digital Separate
47
48 Flag 00 00000000
49 Flag 00 00000000
Timing
Descriptor #2
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
4A Flag 00 00000000
4B Data Type Tag (Descriptor Defined by manufacturer ) 00 00000000
(sDRRS 40Hz)
( Vsync_NEG, Hsync_NEG ), DE only note : LSB is set to '1' if panel is
DE-timing only. H/V can be ignored.
18 00011000
A
4C Flag 00 00000000
4D Descriptor Defined by manufacturer 00 00000000
4E Descriptor Defined by manufacturer 00 00000000
4F Descriptor Defined by manufacturer 00 00000000
50 Descriptor Defined by manufacturer 00 00000000
51 Descriptor Defined by manufacturer 00 00000000
52 Descriptor Defined by manufacturer 00 00000000
53 Descriptor Defined by manufacturer 00 00000000
54 Descriptor Defined by manufacturer 00 00000000
55 Descriptor Defined by manufacturer 00 00000000
56 Descriptor Defined by manufacturer 00 00000000
57 Descriptor Defined by manufacturer 00 00000000
58 Descriptor Defined by manufacturer 00 00000000
59 Descriptor Defined by manufacturer 00 00000000
5A Flag 00 00000000
5B Flag 00 00000000
5C Flag 00 00000000
5D Data Type Tag ( ASCII String ) FE 11111110
5E Flag 00 00000000
5F ASCII String "I" 49 01001001
60
SCII String "N" 4E 01001110
SPEC NO.
PAGE
BT101IW03 V.1
26/ 27
Timing Descriptor #3 (Dynamic DCLK)
(Brightness Table)
Timing Descriptor #4
61 ASCII String "L" 4C 01001100
www.jxlcd.com
www.jxlcd.com
62 0A 01000100
63 20 01101001
64 20 01110011
65 20 01110000
66 20 01101100
67 20 01100001
68 20 01111001
69 20 00001010
6A 20 00100000
6B 20 00100000
6C Detailed timing/monitor 00 00000000
6D descriptor #4 00 00000000
6E Flag 00 00000000
6F Data Type Tag FC 11111100
70 Flag 00 00000000
71 Manufacture P/N "B" 42 01000010
72 Manufacture P/N "T" 54 01010100
73 Manufacture P/N "1" 31 00110001
74 Manufacture P/N "0" 30 00110000
75 Manufacture P/N "1" 31 00110001
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
Checksum
76 Manufacture P/N "I" 49 01001001
77 Manufacture P/N "W" 57 01010111
78 Manufacture P/N "0" 30 00110000
79 Manufacture P/N "3" 33 00110011
7A Manufacture P/N "V" 56 01010110
7B Manufacture P/N "1" 31 00110001
7C 0A 00001010
7D 20 00100000
7E
7F
Extension flag
(# of optional 128 panel ID extension block to follow, Typ = 0)
Check Sum
(The 1-byte sum of all 128 bytes in this panel ID block shall = 0)
SPEC NO.
PAGE
BT101IW03 V.1
27/ 27
00 00000000
C1 11000001
www.jxlcd.com
www.jxlcd.com
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
Loading...