Preparation date: 29-05-2017
Version No.: 2.0
MATERIAL SAFETY DATA SHEET
according to Regulation (EU) No. 1907/2006
PP by Innofil3D BV
1. IDENTIFICATION OF THE PRODUCT AND OF THE COMPANY
Trade name
:
Innofil3D PP
Chemical name
:
Polypropylene
Chemical family
:
Thermoplastic polymer
Use
:
Monofilament for 3D-printing
Company
:
Innofil3D BV
Street address
:
Eerste Bokslootweg 17
Postal code and city
:
7821 AT Emmen
Country
:
The Netherlands
Telephone number
:
+31 (0) 591 820 389
2. HAZARDS IDENTIFICATION
Clasification
Regulation (EC) No
1272/2008
:
The product is not classified according to the CLP regulation.
Directive 67/548/CEE
:
Not classified
Directive 1999/45/CE
:
Not classified
EC guidlines
:
According to the method of calculating the “General Classification
Guideline for the Production of the EC” in the latest valid version,
the product does not require labelling.
3. COMPOSITION/INFORMATION ON INGREDIENTS
Chemical name
:
1-butene, ethene polymer, 1-propene
Weight
:
99.5%
4. FIRST-AID MEASURES
Eye contact
:
Rinse opened eyes for several minutes under running water. If
symptoms persist, consult a doctor. Remove contact lenses.
Continue rinsing.
Professional Series
www.innofil3D.com | info@innofil3d.com | PO Box 1146 | 7801BC Emmen | The Netherlands
Page 1 of 5
Professional Series
Skin contact
:
Wash with soap and water. Visit a doctor if irritation continues in
the skin. After contact with molten product, cool rapidly with cold
water. Do not separate the skin from the solidified product. Call a
doctor immediately.
Inhalation
:
Supply fresh air. In case of disturbances, consult a doctor. After
inhalation of decomposition products, breathe fresh air, rest,
seek for medical help.
Ingestion
:
Rinse mouth and drink plenty of water. Do not induce vomiting.
Consult a doctor in case of persistent symptoms.
Note to physician
:
Treat symptomatically.
5. FIRE-FIGHTING MEASURES
Suitable extinguishing media
:
Any method is applicable.
Unsuitable media
:
Throw water with strong pressure. Carbon dioxide CO₂ .
Hazardous decomposition
products
:
Formation of toxic gases if heated or fire. Irritant gases/vapors.
Smoke, Carbon Monoxide (CO), Carbon Dioxide (CO2) and
Carbonic hydrogen.
Special protective equipment
for firefighters
:
Wear protective breathing apparatus independent of the ambient
air.
6. ACCIDENTAL RELEASE MEASURES
Personal precautions
:
Avoid dust formation. Do not breathe dust. Keep away from
sources of ignition. Avoid eye contact. Danger of slipping on
spilled product or pouring.
Environmental precautions
:
Do not discharge into drains/surface water/ground water.
Methods for cleaning up
:
Allow to solidify, pick up mechanically. Dispose of the material
collected according to regulations.
7. HANDLING AND STORAGE
Safe handling advice
:
Ensure good ventilation/exhaustion. Avoid dust formation. Do not
inhale fumes/dust produced. Remove regularly dust that
inevitably form. Avoid contact with the eyes and skin. Avoid
contact with the product when heated.
Storage conditions
:
Keep in a dry and dark place. Store between 10 and 40 °C.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Control parameters
:
Components with admissible limit values that require monitoring
at the workplace: do not exceed the values for dust
concentration. Additional: Based on references valid at the time
of processing.
www.innofil3D.com | info@innofil3d.com | PO Box 1146 | 7801BC Emmen | The Netherlands
Page 2 of 5
Professional Series
Personal protective equipment
Eye protection
:
Not necessary.
Skin and body protection
:
Not necessary.
Respiratory protection
:
Not necessary.
Hand protection
:
Not necessary. When material is molten, use protective gloves.
Hygiene measures
:
Do not eat, drink, smoke of sniff during working with the material.
Do not breathe dust/smoke/mist. Avoid contact with eyes and
skin. Wash hand before and after working with the material.
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance
:
Filaments.
Color
:
Semi-transparent natural.
Physical state
:
Flexible but solid at room temperature.
Odor
:
Odorless.
Melting point/range
:
220-240 °C
Boiling point/range
:
Not applicable.
Decomposition temperature
:
Not applicable.
Density
:
1.05
pH : Not applicable.
Vapor pressure
:
Not applicable.
Vapor density
:
Not applicable.
Evaporation rate
:
Not applicable.
Water solubility
:
Insoluble.
Solubility in other solvents
:
Acetone.
Softeningpoint
:
105 °C
10. STABILITY AND REACTIVITY
Stability
:
Stable.
Conditions to avoid
:
Avoid impact, friction, heat, sparks, and electrostatic charges.
Materials to avoid
:
Strong oxidants.
Decomposition
:
Irritant/toxic gases/vapors. Smoke. Carbon monoxide (CO) and
Carbon dioxide (CO2)
Polymerization
:
Non applicable.
www.innofil3D.com | info@innofil3d.com | PO Box 1146 | 7801BC Emmen | The Netherlands
Page 3 of 5
Professional Series
11. TOXICOLOGICAL INFORMATION
Long term toxicity
:
No data.
Toxicological effects
:
Based on our current information and knowledge, the product
does not cause any adverse health effects when handled properly.
Also there are no carcinogenic, mutagenic and toxic effects
known.
Skin
:
Dust may cause mechanical irritation.
Eye : Dust may cause mechanical irritation.
12. ECOLOGICAL INFORMATION
Mobility
:
Bioconcentration is not expected because of the high molecular
weight (MW > 1000). In the terrestrial environment, material is
expected to remain in the soil. In the aquatic environment
material will sink and remain in the sediment.
Ecotoxicity effects
:
It is not expected to be very toxic, but if ingested by birds or
aquatic life, can cause adverse mechanical effects
Persistence and
degradability
:
This solid water-insoluble polymeric are expected to be inert in the
environment. Surface degradation is expected with exposure to
sunlight . Appreciable biodegradation is not expected.
13. DISPOSAL CONSIDERATIONS
Methods for treating waste
Recommendation
:
Disposal according to official regulations.
European waste catalog
:
Allocation of waste codes according to the European waste list
depends on the source generating the waste.
Contaminated packaging
:
Disposal according to official regulations.
14. TRANSPORT INFORMATION
IMDG
:
Not regulated.
ICAO/IATA
:
Not regulated.
www.innofil3D.com | info@innofil3d.com | PO Box 1146 | 7801BC Emmen | The Netherlands
Page 4 of 5
Professional Series
15. REGULATORY INFORMATION
NOTICE: The information herein is presented in good faith and believed to be accurate as of the
print date shown above. However, no warranty, express or implied is given. Regulatory
requirements are subject to change and may differ from one location to another; it is the buyer’s
responsibility to ensure that its activities comply with federal, state or provincial, and local laws. See
other sections for health and safety information.
EU regulation 10/2011
:
Approved.
FDA
:
Approved.
Regulation (EC) No.
1935/2004
:
Compliant.
2023/2006/EC GMP
:
Compliant.
16. OTHER INFORMATION
- The information in this Material Safety Data Sheet (MSDS) is mainly based on information
used from the supplier of the raw materials which are used for production of the filaments.
- The information in this Material Safety Data Sheet (MSDS) is based on current knowledge and
experience. No liability can be assumed for the accuracy and completeness of this
information.
- Users should consider this information only as additional to other data gathered. Independent
determination of suitability and completeness of information from all available sources is
essential to ensure proper and safe use and disposal of these materials.
- The information in this MSDS applies for this specific material only. It therefor does not apply
for its usage in combination with other materials or ways of processing.
www.innofil3D.com | info@innofil3d.com | PO Box 1146 | 7801BC Emmen | The Netherlands
Page 5 of 5
Loading...