INNOCIGS ULTEX T80 – KOMPAKTES GERÄT MIT 80 WATT, DISPLAY UND MENÜFÜHRUNG
Nutzerinformationen
Vielen Dank, dass Sie sich für ein InnoCigs Produkt entschieden haben! Bei unserem gesamten Sortiment
legen wir großen Wert auf hohe Qualitäts- und Sicherheitsansprüche. Wir wünschen Ihnen viel Spaß beim
Dampfen mit Ihrem neuen E-Zigaretten-Produkt!
Bitte lesen Sie die Bedienungsanleitung vor Gebrauch sorgsam durch, um eine korrekte Nutzung des
E-Zigaretten-Produkts von InnoCigs zu gewährleisten. Verwenden Sie in Kombination mit diesem Produkt
bitte nur originale bzw. empfohlene Produkte. Der Hersteller leistet keinen Service und/oder keine Garantie
bei der Nutzung mit nicht empfohlenen Produkten.
Sollten Sie Fragen rund um Ihr InnoCigs E-Zigaretten-Produkt haben oder weitere Informationen
benötigen, kontaktieren Sie bitte Ihren Fachhändler oder besuchen Sie unsere Website www.innocigs.com.
Personen unter 18 Jahren, Schwangere, stillende Mütter und Menschen mit Herz-Kreislauf-Erkrankungen dürfen dieses
Produkt nicht verwenden. Nicht empfohlen für Nichtraucher. Das E-Zigaretten-Produkt darf nicht in die Hände von
Kindern und Jugendlichen gelangen.
Dieses Produkt darf
nicht von Minderjährigen
verwendet werden.
Dieses Produkt muss für
Kinder und Jugendliche
unzugänglich aufbewahrt
werden.
Dieses Produkt darf nicht von
Schwangeren oder stillenden
Müttern genutzt werden.
Dieses Produkt entspricht den innerhalb der EU gültigen
Bestimmungen für technische Geräte und darf in den
Ländern der EU vertrieben werden.
Alte Elektrogeräte oder verbrauchte Akkus gehören nicht
in den Hausmüll!
Bitte entsorgen Sie Altbatterien und -geräte – wie vom
Gesetzgeber vorgeschrieben – an einer kommunalen
Sammelstelle oder geben Sie sie im Handel vor Ort
kostenlos ab, damit Rohstoffe und mögliche Schadstoffe
gezielt verwertet werden können.
1. Sollte Ihnen das Gerät heruntergefallen sein, überprüfen Sie bitte, ob sich keine Komponenten gelockert
haben, ob kein Liquid austritt und ob kein Defekt an Ihrem Mundstück vorliegt. Sofern nach visueller
Prüfung des Produkts keine Anzeichen einer Beschädigung vorliegen, können Sie das Gerät weiterbenutzen. Bitte wischen Sie Ihr Mundstück zuvor aus hygienischen Gründen mit einem Tuch ab.
2. Das Gerät sollte nicht benutzt werden, wenn sich Risse oder Deformationen im Material zeigen oder ein
defektes Teil ausgetauscht werden sollte. Versuchen Sie bei einem Defekt niemals, das Gerät selbst zu
reparieren.
3. Das Gerät sollte nicht benutzt werden, wenn das Liquid in Ihrem Clearomizertank verbraucht oder
fast verbraucht ist. Gleiches gilt für den Fall, dass Sie eine Veränderung des Geschmacks wahrnehmen.
Bitte befüllen Sie den Clearomizertank mit frischem Liquid und tauschen Sie Ihren Verdampferkopf
durch einen neuen aus, bevor Sie Ihre E-Zigarette weiterbenutzen. Da es sich bei Verdampferköpfen um
Verschleißteile handelt, müssen sie regelmäßig gewechselt werden.
4. Lagern Sie das Gerät nie in Räumen mit sehr hohen Temperaturen oder mit besonders hoher Luftfeuchtigkeit. Vermeiden Sie längere direkte Sonneneinstrahlung.
5. Die geeignete Temperatur liegt für das Laden des Akkus bei 5°C bis 45°C und für den Gebrauch bei
-10°C bis 60°C.
6. Wenn Liquid mit Ihrer Haut in Berührung kommt, wischen Sie es schnellstmöglich ab und reinigen Sie
die Stelle anschließend gründlich mit klarem Wasser.
7. Wenn Sie versehentlich Liquid verschlucken, wenden Sie sich bitte an eine Vergiftungszentrale. Unter der
Telefonnummer +49 (0)30 - 19 240 erreichen Sie Tag und Nacht den Giftnotruf der Charité Universitätsmedizin Berlin. In Österreich steht der 24-Stunden-Notruf der Wiener Vergiftungsinformationszentrale
unter +43 (0)1 - 406 43 43 zur Verfügung. In Frankreich wenden Sie sich bitte an eine der lokalen
Vergiftungszentralen. Verständigen Sie in Notfällen bitte umgehend den Notruf.
8. Das Inhalieren nikotinhaltigen Liquids kann die Herzfrequenz und/oder den Blutdruck erhöhen. Nikotin
kann Übelkeit, Schwindel und/oder Magenschmerzen verursachen. Wenn Sie an sich oder Menschen in
Ihrer Umgebung unerwünschte Wirkungen feststellen, verwenden Sie dieses Produkt bitte nicht weiter
und konsultieren Sie einen Arzt.
9. Beachten Sie bei der Nutzung von E-Zigaretten lokale Gesetze.
10. Das Produkt darf nicht in die Hände von Kindern und Jugendlichen gelangen.
Dieses E-Zigaretten-Produkt kann mit nikotinhaltigem Liquid verwendet werden. Nikotin ist ein Stoff, der
sehr stark abhängig macht.
Allgemeine Informationen zu Zugtechniken beim Dampfen
Beim Dampfen wird zwischen zwei Zugtechniken unterschieden:
Moderates Dampfen (Mund-zu-Lunge)
Der Dampf einer E-Zigarette wird während der gesamten Zugdauer zunächst im Mundraum gesammelt und
anschließend in die Lunge inhaliert. Diese Zugtechnik wird als moderates Dampfen von Mund-zu-Lunge
bezeichnet und ist genauso wie beim Rauchen einer Tabak-Zigarette. Voraussetzung ist ein spürbarer
Widerstand beim Zug an der E-Zigarette. Verdampferköpfe, die diese Zugtechnik im moderaten Bereich
(Widerstand i.d.R. > 1 Ohm) unterstützen, werden häug als MTL-Head gekennzeichnet, wobei MTL für das
Englische “Mouth to Lung” steht. (weitere Abkürzungen: ML, M2L)
Der Dampf einer E-Zigarette wird während des Zuges direkt in die Lunge inhaliert. Diese Zugtechnik wird als
subohmes Dampfen mit direkter Lungeninhalation bezeichnet. Voraussetzung ist ein geringer Zugwiderstand
und eine hohe Luftzufuhr zum Verdampferkopf. Beides wirkt sich positiv auf die Produktion großer
Dampfmengen aus. Verdampferköpfe, die diese Zugtechnik im Subohm-Bereich (Widerstand i.d.R. < 1 Ohm)
unterstützen, werden häug als DL-Head gekennzeichnet, wobei DL für das Englische “Direct Lung” steht.
(weitere Abkürzungen: DTL, D2L)
07
Page 11
INNOCIGS ULTEX T80 – LIEFERUMFANG | AUFBAU DES GERÄTS
Bitte laden Sie den wechselbaren 18650er Akku vor der ersten Inbetriebnahme vollständig auf. Bitte
beachten Sie die Kennzeichnung der Plus- und Minus-Pole im Akkufach. Achten Sie unbedingt darauf, dass
die Oberäche der Akku-Zelle keine Beschädigung aufweist. Das Gerät verfügt über einen 510er Anschluss
mit gefedertem Verbindungsstück, wodurch er zu einer Vielzahl an Clearomizern passt.
Hinweis zur Reinigung
Verwenden Sie zur Reinigung des Geräts ein trockenes Tuch oder ein Wattestäbchen.
Power On/Off
Betätigen Sie die Feuertaste fünf Mal schnell hintereinander (innerhalb von 2 Sekunden), um das Gerät
einzuschalten und fünf Mal, um es wieder auszuschalten. Wir empfehlen Ihnen, das Gerät während des
Transports und bei längerer Nichtbenutzung auszuschalten.
09
Page 13
INNOCIGS ULTEX T80 – INBETRIEBNAHME DES GERÄTS
Dampfen
Während Sie die Feuertaste des Geräts gedrückt halten, inhalieren Sie den Dampf langsam und kontinuierlich
über das Mundstück Ihres Clearomizers. Lassen Sie die Feuertaste beim Ausatmen des Dampfes los.
Sperren/Entsperren der Einstelltasten
Halten Sie die Einstelltasten “Auf” und “Ab” beim eingeschalteten Gerät gleichzeitig für zwei Sekunden
gedrückt, bis das Display “Key Lock” anzeigt. Die Einstelltasten sind jetzt gesperrt. Um sie wieder zu entsperren, halten Sie die Tasten für weitere zwei Sekunden gedrückt, bis Ihnen “Key Unlock” angezeigt wird. Mit
dieser Funktion vermeiden Sie ein unbeabsichtigtes Verändern Ihrer Vaping-Einstellungen.
Auaden und Updaten des Geräts
Das ausgewogene Ladesystem ermöglicht ein schnelles Auaden mit einem maximalen Ladestrom von bis zu
2 A. Sie können das Gerät per USB-Kabel über einen PC oder mit einem externen Gerät auaden, in das Sie
die Akkuzellen hineinlegen. Verbinden Sie das Gerät auch für ein Software-Update via QC-USB-Ladekabel mit
einem internetfähigen PC.
10
Page 14
INNOCIGS ULTEX T80 – ECKDATEN & LEISTUNGSMERKMALE
InnoCigs Ultex T80 Akkuträger Eckdaten
Ausgabemodi POWER (VW) | TC (Ni, Ti, SS316) | TCR (M1, M2, M3) | Bypass
Ausgangsleistung 1 bis 80 Watt
Elektrische Spannung 0,5 bis 9 V
Temperaturbereich 100°C bis 315°C | 200°C bis 600°F
Widerstandsbereich 0,05 bis 3,5 Ohm im POWER-/Bypass-Modus
0,05 bis 1,5 Ohm im TC- /TCR-Modus
Ladestrom max. 2 A
Durchmesser 26 mm
Höhe 95 mm
Gewindetyp 510
11
Page 15
INNOCIGS ULTEX T80 – REGELUNG DER LEISTUNGS- UND TEMPERATURABGABE
Allgemeine Bedienung zur Regelung der Leistungs- und Temperaturabgabe
Die Leistung des Geräts kann 1 Watt bis hin zu 80 Watt betragen. Eine Änderung der Wattzahl verändert
auch den Geschmack und das Dampfverhalten. Je höher die eingestellte Wattzahl ist, desto intensiver ist
die Dampfentwicklung. Ähnlich verhält es sich mit der Temperature Control: Je höher die Temperatur, desto
größer ist die Dampfentwicklung. Halten Sie die Einstelltaste “Auf” oder “Ab” gedrückt, um eine automatisch
fortlaufende Steigerung oder Minderung der Wattzahl bzw. der Temperatur durchzuführen.
Wechsel zwischen °C und °F
Die Temperatur kann im TCR-Modus zwischen 100°C und 315°C oder 200 bis 600 °F eingestellt werden.
Mit den Einstelltasten “Auf” und “Ab” können Sie die Temperatur erhöhen oder senken. Halten Sie die
Einstelltasten jeweils etwas länger gedrückt, um den Wert schneller einzustellen.
12
Page 16
INNOCIGS ULTEX T80 – ERLÄUTERUNGEN ZU DEN BETRIEBSMODI
POWER-Modus (Variable Wattage)
Im POWER-Modus werden Verdampferköpfe in einem Widerstandsbereich zwischen 0,05 Ohm und 3,5 Ohm
unterstützt. Die Leistung kann im POWER-Modus – je nach verwendetem Verdampferkopf – zwischen
1 Watt und 80 Watt liegen.
Bypass-Modus
Der Bypass-Modus ist ein direkter Ausgabemodus in Bezug zur Spannung. In dieser Einstellung ist ein
Widerstandsbereich von 0,05 bis 3,5 Ohm möglich, um eine einwandfreie Nutzung zu gewährleisten.
Die Ausgangsleistung reguliert sich automatisch in Korrelation zum jeweiligen Akkuzustand.
TC/TEMP-Modus (Temperature Control)
In den Modi TC-Ni, TC-Ti und TC-SS316 unterstützt das Gerät Verdampferköpfe mit Wicklungen aus
Nickel (Ni), Titan (Ti) und Edelstahl (SS316), deren Widerstand zwischen 0,05 Ohm und 1,5 Ohm liegt.
Die Temperatur kann im TC-Modus – je nach verwendetem Verdampferkopf – zwischen 100°C und 315°C
(200°F und 600°F) liegen.
13
Page 17
INNOCIGS ULTEX T80 – ERLÄUTERUNGEN ZU DEN BETRIEBSMODI
TCR-Modus (Temperature Coefcient of Resistance)
Im TCR-Modus (M1, M2, M3) unterstützt das Gerät Heads mit Wicklungen aus Nickel (Ni200), Titan (Ti),
Nickel-Eisen (NiFe) und Edelstahl (SS316), deren Widerstand zwischen 0,05 Ohm und 1,5 Ohm liegt. Die
Temperatur kann im TCR-Modus je nach verwendetem Verdampferkopf zwischen 100°C und 315°C
(200°F und 600°F) liegen. Dieser Modus erlaubt es Ihnen, verschiedene Temperaturkoefzienten des
Drahtes zu wählen bzw. ihn mit unterschiedlichen TCR-Werten zu betreiben.
Bitte beachten Sie, dass der Widerstand des verwendeten Verdampferkopfes vor der ersten Nutzung im
TC-/TCR-Modus festgesetzt werden muss.
14
Page 18
INNOCIGS ULTEX T80 – AUSWAHL & BEDIENUNG DER MENÜS
Wechseln zwischen den Betriebsmodi
Drücken Sie beim eingeschalteten Gerät die Feuertaste drei Mal schnell hintereinander. Navigieren Sie durch
Drücken der “Auf”/”Ab”-Einstelltasten” zwischen den verfügbaren Modi. Drücken Sie die Feuertaste, um eine
getroffene Auswahl zu bestätigen.
Bedienung der Menüs
Halten Sie gleichzeitig die Feuertaste und die “Auf”-Einstelltaste für ca. 3 Sekunden gedrückt, um ins Menü
zu gelangen, wo Sie weitere Einstellungen vornehmen können. Navigieren Sie mit den “Auf”/”Ab”-Einstelltasten innerhalb des Menüs. Drücken Sie die Feuertaste, um in ein Untermenü zu gelangen. Navigieren Sie mit
den “Auf”/”Ab”-Einstelltasten innerhalb des entsprechenden Untermenüs. Drücken Sie die Feuertaste, um
eine getroffene Auswahl zu bestätigen.
15
Page 19
INNOCIGS ULTEX T80 – AUSWAHL & BEDIENUNG DER MENÜS
Exit
Drücken Sie die Feuertaste, um das Menü zu verlassen.
Anzeige von Subparametern
Im Menü SUBPARA können Sie festlegen, ob auf dem Bildschirm während des normalen
Betriebes die Zuganzahl (“Puff”), die insgesamt gedampfte Zeit (“Time”) oder die Spannung in
Volt (“Volt”) angezeigt wird.
In den Menüpunkten PUFF und TIME können Sie die Werte durch längeres Drücken der
“Auf”-Einstelltaste zurücksetzen.
16
Page 20
INNOCIGS ULTEX T80 – AUSWAHL & BEDIENUNG DER MENÜS
Aktivieren/Deaktivieren der Display-Anzeige
Im Menü STEALTH können Sie festlegen, ob die Bildschirmanzeige während des Dampfens
aueuchtet oder nicht. Wählen Sie “On” um den Stealth-Modus zu aktivieren, “Off” um ihn
zu deaktivieren.
Einstellungen zur Vorheizfunktion im VW-Modus
Im VW-Modus verfügt das Gerät über eine Vorheizfunktion. Im Menü PREHEAT können Sie Einstellungen bezüglich der Vorheizfunktion vornehmen. Legen Sie unter “Pwr” die Leistung in Watt
und unter “Dura” die Dauer in Sekunden fest. Unter “Exit” verlassen Sie das Menü PREHEAT.
Hinweis
Auch in den temperaturgeregelten Modi TC/TCR können Sie die Vorheizfunktion nutzen. Drücken Sie,
während der TC/TCR-Modus aktiviert ist die Feuertaste vier Mal in schneller Folge. Durch Drücken der
“Auf”/”Ab”-Einstelltasten können Sie eine Leistung zwischen einem und 80 Watt festlegen. Drücken
Sie die Feuertaste, um Ihre Auswahl zu bestätigen. Mit dieser Leistung beginnt das Gerät in den
Temperatur-Modi zu feuern.
17
Page 21
INNOCIGS ULTEX T80 – AUSWAHL & BEDIENUNG DER MENÜS
Anzeige der aktuellen Hardware/Firmware Version
Im Menü VERSION können Sie sich Ihre aktuelle Hardware-/Firmware-Version anzeigen lassen.
Drücken Sie die Feuertaste, um die Anzeige zu verlassen.
Sperren des Widerstandes im TC-/TCR-Modus
Im Menü COIL können Sie den aktuellen Widerstandswert für den Betrieb im TC/TCR-Modus
sperren (Symbol eines geschlossenen Schlosses) oder entsperren
(Symbol eines geöffneten Schlosses).
Hinweis
1. Bitte verwenden Sie die Sperr-Funktion nur bei Raumtemperatur, sodass der richtige Basiswiderstand
im Lock-Modus angezeigt werden kann. Ist dies nicht der Fall, so kann es zu fehlerhaften Messergebnissen
kommen, die sich auch negativ auf die Schutzfunktionen auswirken können.
18
Page 22
INNOCIGS ULTEX T80 – AUSWAHL & BEDIENUNG DER MENÜS
2. Wenn Sie im im TC/TEMP- oder TCR-Modus versehentlich konventionelle Wicklungen verwenden
wollen, die für temperaturgeregeltes Dampfen nicht geeignet sind, oder deren Widerstand größer als
1,5 Ohm ist, wechselt das Gerät automatisch in den VW-Modus.
Festlegen des Temperaturkoefzienten im TCR-Modus
Im Menü TCR haben Sie die Möglichkeit, TCR-Werte für die Speicherplätze M1, M2 bzw.
M3 festzulegen. Der TCR-Wertebereich liegt zwischen 1 und 999.
Auf dem Display erscheint die Meldung “ATOMIZER SHORT”, sobald am Head ein Kurzschluss vorliegt.
Kein Verdampferkopf erkannt
Auf dem Bildschirm erscheint “NO ATOMIZER FOUND”, wenn kein Verdampfer verbunden ist.
Akku schwach
Wenn die Spannung der Batterie unter 2,1 V sinkt, zeigt das Gerät “WEAK BATTERY” an. Die Ausgangsleistung wird adäquat zur Spannung reduziert.
Akku auaden
Wenn die Spannung unter 2,0 V fällt, erscheint auf dem Display “BATTERY LOW”. Bei weiterer Betätigung
der Feuertaste, erscheint “BATTERY LOW LOCK” und das Gerät schaltet sich ab. Bitte laden Sie das Gerät
wieder auf.
Liegt der Widerstand der Wicklung unter 0,05 Ohm, erscheint im Display “ATOMIZER LOW”.
Temperaturschutz
Hat im TC/TCR-Modus die Ist-Temperatur der Wicklung die Soll-Temperatur erreicht, zeigt der Bildschirm
“PROTECT” an. Sie können das Gerät ganz normal weiter verwenden.
Temperatur-Alarm
Liegt die Temperatur des Gerätes über 70 °C, schaltet sich das Gerät automatisch ab und im Display erscheint
“DEVICE TOO HOT”. Sie können mit dem Dampfen fortfahren, nachdem sich das Gerät abgekühlt hat.
21
Page 25
INNOCIGS – GARANTIELEISTUNGEN & REPARATUREN
Garantiebedingungen
Alle Produkte von InnoCigs unterliegen einer strengen Qualitätskontrolle. Sie erhalten zusätzlich zu der
gesetzlichen Gewährleistungspicht eine 6-monatige Garantie auf alle InnoCigs-Produkte. Die Garantiezeit
von 6 Monaten gilt ab Kaufdatum beim Fachhändler. Das Datum auf Ihrem Kaufbeleg ist ausschlaggebend.
Während der Garantiezeit werden Geräte, die Defekte aufweisen, von der Firma InnoCigs repariert oder
ersetzt.
Verschleißteile wie Mundstücke und Verdampferköpfe sind von der Garantie ausgenommen.
Ersetzte Geräte oder Einzelteile gehen in das Eigentum von InnoCigs über. Die Garantieleistungen bewirken
weder eine Verlängerung der Garantiezeit, noch setzen sie eine neue Garantie in Gang.
22
Page 26
INNOCIGS – GARANTIELEISTUNGEN & REPARATUREN
Garantieansprüche sind ausgeschlossen bei Schäden durch:
- Nichtbeachtung der für das Gerät geltenden Sicherheitshinweise
- Nichtbeachtung der Bedienungsanleitung
- Gewaltanwendung (z.B. Schlag, Stoß, Fall)
- Eingriffe, die nicht durch die von InnoCigs autorisierten Serviceadressen vorgenommen wurden
- eigenmächtige Reparaturversuche
- Einsendung in nicht transportsicherer Verpackung
InnoCigs behält sich bei allen Garantiefällen das Recht einer genauen Prüfung bis zur endgültigen
Entscheidung vor. InnoCigs behält sich das Recht vor, die Gewährleistungsbedingungen zu überarbeiten.
23
Page 27
INNOCIGS – GARANTIE & SERVICE
Garantie, Gewährleistung & Service
Sollte das Produkt nicht funktionieren oder in irgendeiner Weise defekt sein, so wenden Sie sich zunächst
bitte direkt an den Fachhändler, von dem Sie das Produkt erworben haben.
Sollte die Geltendmachung einer Garantie erforderlich sein, gehen Sie bitte wie folgt vor: Bitte setzen Sie
sich mit dem InnoCigs Kundenservice per E-Mail, Fax oder Telefon in Verbindung. Alternativ können Sie den
Austausch-Service auf unserer Webseite www.innocigs.com nutzen.
Bei Fragen rund um die Bedienung und Verwendung wenden Sie sich gerne an unseren Kundenservice.
INNOCIGS ULTEX T80 – APPAREIL COMPACT AVEC 80 WATTS, AFFICHAGE ET NAVIGATION DANS LES MENUS
Informations pour les utilisateurs
Nous vous remercions d‘avoir choisi un produit InnoCigs ! Pour toute notre gamme, nous accordons une
grande importante aux normes de qualité et de sécurité. Nous vous souhaitons bien du plaisir en vapotant
avec votre nouvelle cigarette électronique !
Veuillez lire attentivement le mode d‘emploi avant usage an de garantir une utilisation correcte de le
produit e-cigarette. En combinaison avec ce produit, utilisez exclusivement des produits originaux et
recommandés. Le fabricant ne garantit aucun service après-vente ni aucune garantie en cas d‘utilisation de
produits non recommandés
Pour toute question concernant votre cigarette électronique InnoCigs ou si vous avez besoin d‘autres
informations, merci de contacter votre revendeur spécialisé ou de vous rendre sur notre site internet
INNOCIGS ULTEX T80 – INDICATIONS ET MESURES DE PRÉCAUTION
Les personnes âgées de moins de 18 ans, les femmes enceintes, les mères allaitantes et les personnes souffrant de maladies cardiovasculaires ne doivent pas utiliser ce produit. Déconseillé aux non-fumeurs. Tenir la cigarette électronique
hors de portée des enfants et des adolescents.
Ce produit ne doit pas être
utilisé par des personnes
mineures.
Ce produit ne doit pas être
utilisé par des femmes
enceintes ou des mères
allaitantes.
Ce produit doit être
conservé hors de portée des
enfants et des adolescents.
Ce produit répond aux dispositions applicables au
sein de l‘Union Européenne concernant les appareils
techniques, et il peut être vendu dans les pays de
l‘Union Européenne.
Les vieux appareils électriques ou accus usagés ne doivent
pas être jetés aux ordures ménagères. Veuillez jeter les
accus et appareils usés auprès d‘un point de collecte conformément aux prescriptions légales - ou déposez-les
gratuitement sur place dans le commerce, an que les
matières premières et de potentielles substances nocives
puissent être traitées de façon ciblée.
28
Page 32
INNOCIGS ULTEX T80 – INDICATIONS ET MESURES DE PRÉCAUTION
Recommandations d‘utilisation
1. Si vous avez fait tomber votre appareil, veuillez vérier qu‘aucun composant ne se soit desserré,
qu‘aucun liquide ne s‘écoule et que votre embout ne présente aucun défaut. Dans la mesure où, après
un contrôle visuel, le produit ne présente aucun dommage, vous pouvez continuer de l‘utiliser. Veuillez
tout d‘abord essuyer l‘embout pour des raisons d‘hygiène.
2. L‘appareil ne doit pas être utilisé s‘il présente des fentes ou des déformations du matériel ou si une
pièce défectueuse doit être remplacée. En cas de dysfonctionnement, n‘essayez en aucun cas de réparer
l‘appareil vous-même.
3. L‘appareil ne doit pas être utilisé si le liquide du réservoir du clearomiseur est totalement ou presque
totalement consommé. Il en va de même si vous percevez une modication du goût. Veuillez remplir le
réservoir du clearomiseur avec du liquide frais et remplacez la tête de votre atomiseur par une nouvelle
avant de continuer à utiliser votre cigarette électronique. Dans la mesure où les têtes sont des pièces
consommables, elles doivent régulièrement être changées.
4. Ne rangez jamais l‘appareil dans une pièce à une température élevée ou présentant une humidité de l‘air
particulièrement forte. Évitez de l‘exposer aux rayons du soleil de manière prolongée.
29
Page 33
INNOCIGS ULTEX T80 – INDICATIONS ET MESURES DE PRÉCAUTION
5. La température adaptée va de 5 ºC à 45 ºC pour la recharge des batteries, et de - 10 ºC à 60 ºC pour
l‘utilisation.
6. Si du liquide entre en contact avec votre peau, essuyez-le au plus vite, puis nettoyez rigoureusement à
l‘eau claire.
7. Si vous avalez du liquide par mégarde, veuillez contacter un centre antipoison. Vous pouvez joindre à
toute heure du jour et de la nuit le service d‘urgence antipoison de l‘hôpital universitaire de la Charité
de Berlin au +49 (0)30 - 19 240. En Autriche, le service d‘urgence 24h/24 de la centrale viennoise
d‘information antipoison est disponible au +43 1 - 406 43 43. En France, veuillez contacter l‘un des
centres locaux antipoison. En cas d‘urgence, merci d‘en aviser immédiatement le service d‘urgence.
8. Inhaler des produits contenant de la nicotine peut augmenter la fréquence cardiaque et/ou la pression
sanguine. La nicotine peut entraîner des nausées, des vertiges et/ou des maux d‘estomac. Si vous
constatez des effets indésirables sur vous-même ou sur des personnes de votre entourage, veuillez ne
plus utiliser ce produit et consulter un médecin.
9. Respectez les législations locales relatives à l‘utilisation de cigarettes électroniques.
10. Le produit doit rester hors de portée des enfants et des adolescents.
30
Page 34
INNOCIGS ULTEX T80 – INDICATIONS ET MESURES DE PRÉCAUTION
Avertissement
Cet appareil peut être utilisée avec du liquide nicotiné. La nicotine est une substance créant une très forte
dépendance.
Informations générales sur vape et techniques de tirage
Le vapotage distingue deux techniques de tirage différentes :
Vape modérée par tirage indirect (de la bouche vers les poumons)
La vapeur d‘une cigarette électronique, durant la totalité de la durée de tirage, passe d‘abord par la bouche
pour être ensuite inhalée par les poumons. Cette technique de tirage est désignée comme vape modérée de
la bouche vers les poumons et est similaire à celle d‘une vraie cigarette. Elle implique un tirage « serré »
sur la cigarette électronique. Les resistánces qui permettent cette technique de tirage modérée
(résistance i.d.R. > 1 Ohm) sont souvent désignées comme des resistánces MTL, abréviation de
l‘expression anglaise « Mouth to lung ». (autres abréviations possibles : ML, M2L)
31
Page 35
INNOCIGS ULTEX T80 – INDICATIONS ET MESURES DE PRÉCAUTION
Vape à basse résistance en sub-ohm (inhalation directe vers les poumons)
La vapeur d‘une cigarette électronique, durant la totalité de la durée de tirage, passe directement vers les
poumons. Cette technique de tirage est désignée comme vape à basse résistance en sub-ohm avec inhala-
tion directe vers les poumons. Elle implique un tirage plus réduit et un débit d‘air (airow) plus élevé vers
la resistánce. Les deux techniques ont un impact positif sur la production de grandes quantités de vapeur.
Les résistances qui permettent cette technique de tirage (résistance i.d.R. < 1 Ohm) sont souvent désignées
comme des résistances DL, abréviation de l‘expression anglaise « Direct lung ».
(autres abréviations possibles : DTL, D2L)
32
Page 36
INNOCIGS ULTEX T80 – CONTENU DE LA LIVRAISON | STRUCTURE DE L‘APPAREIL
Contenu Box Ultex T80
1x Box Ultex T80
1x Câble QC USB
1x Manuel d‘utilisation
Boutons de réglage “-” (MOINS)
Connection 510
Bouton Fire
Bouton de réglage “+” (PLUS)
Port Micro-USB
Ècran OLED (0,49 pouces)
Couvercle de la
batterie
33
Page 37
INNOCIGS ULTEX T80 – MISE EN SERVICE DE L‘APPAREIL
Mode d‘emploi
Chargez complètement l’accu 18650 échangeable requis avant de procéder à la mise en service initiale.
Veuillez tenir compte du marquage des pôles Plus et Moins dans le logement à accu. Veillez absolument
à ce que la surface d’accu ne présente aucune trace de détérioration. L‘appareil est doté d‘un raccord
510 à connecteur à ressort lui permettant de s‘adapter à un grand nombre de clearomiseurs subohm.
Instruction de nettoyage
Pour le nettoyage de l‘appareil, utilisez un chiffon sec ou un coton-tige.
Marche/Arrêt
Appuyez cinq fois de suite rapidement sur le bouton re pour mettre en marche l‘appareil et à nouveau cinq
fois pour l‘éteindre. Nous vous recommandons d‘éteindre l’appareil pendant le transport et en cas de non
utilisation prolongée.
34
Page 38
INNOCIGS ULTEX T80 – MISE EN SERVICE DE L‘APPAREIL
Vapotage
Pendant que vous maintenez enfoncée la touche d‘allumage de votre e-cigarette, inhalez la vapeur
lentement et en continu via l‘embout de votre clearomiseur. Relâchez le bouton re lorsque vous rejetez
la fumée.
Verrouillage/déverrouillage des boutons de réglage « PLUS » et « MOINS »
Quand l‘appareil est allumé, maintenez les boutons de réglage « PLUS » et « MOINS » appuyés pendant deux
secondes jusqu‘à ce que « Key Lock » apparaisse sur l‘écran. Les boutons de réglage sont maintenant verrouillés.
Pour les déverrouiller, maintenez ces boutons appuyés pendant deux autres secondes jusqu‘à ce que
« Key Unlock » apparaisse. Cette fonction vous permet d‘éviter de modier involontairement vos réglages de vape.
Recharger et mise à jour la batterie
Le système de chargement équilibré permet de charger avec un courant maximal de 2 A. Vous pouvez
recharger l’appareil en le branchant avec un câble USB sur un PC ou avec un appareil externe après
y avoir placé la batterie.Raccordez aussi l’appareil via un câble de chargement QC-USB pour le recharger
ou effectuer une mise à jour du logiciel.
35
Page 39
INNOCIGS ULTEX T80 – DONNÉES CLÉS ET CARACTÉRISTIQUES DE PERFORMANCE
Caractéristiques de performance du box InnoCigs Ultex T80
Modes de sortie POWER (VW) | TC (Ni, Ti, SS316) | TCR (M1, M2, M3) | Bypass
Puissance de sortie 1 à 80 Watt
Tension électrique 0,5 à 9 V
Plage de température 100°C à 315°C | 200°C à 600°F
Plage de résistance 0,05 à 3,5 Ohm en mode POWER/Bypass
0,05 à 1,5 Ohm en mode TC/TCR
Courant de charge max. 2 A
Diamètre 26 mm
Hauteur 95 mm
Type de letage 510
36
Page 40
INNOCIGS ULTEX T80 – RÉGLAGE DE LA PUISSANCE DE LA TEMPÉRATURE
Opérations générales de régulation de la puissance et de la température
En fonction de la résistance utilisée, la puissance de l‘appareil peut aller de 1 watts à 80 watts et vous
pouvez sélectionner la température de la vapeur de 100 °C à 315 °C au maximum. Toute modication du
nombre de watts ou de la température modie également le goût et la composition de la vapeur. Plus le
nombre de watts ou la température est élevé(e), plus la vapeur formée est intense. Maintenez l‘un des
boutons de réglage appuyé pour augmenter ou réduire automatiquement et en continu le nombre de watts
ou la température.
Commuter entre °C et °F
Si vous continuez d‘appuyer sur le bouton de réglage « PLUS » quand la valeur 315 °C est afchée, vous
passez automatiquement à la plus basse valeur en degrés Fahrenheit (200 °F). De même, vous passez
automatiquement à la plus grande valeur en degrés Fahrenheit (600 °F) si vous continuez d‘appuyer sur le
bouton de réglage « MOINS » quand la valeur minimum en degrés Celsius (100 °C) est afchée.
37
Page 41
INNOCIGS ULTEX T80 – EXPLICATIONS RELATIVES AUX MODES DE FONCTIONNEMENT
Mode POWER (Variable Wattage)
En mode POWER, les résistances fonctionnent dans une plage de 0,05 à 3,5 ohms. Dans le mode VW, la
puissance peut être comprise entre 1 et 80 W, en fonction de la résistance utilisée.
Mode bypass
Le mode bypass est un mode de sortie direct par rapport à la tension. Il vous permet de régler une plage de
résistance de 0,05 à 3,5 ohms, garantissant ainsi une utilisation parfaite de l‘appareil. La puissance de sortie
se règle automatiquement en fonction de l‘état momentané de l‘accu.
Mode TC/TEMP (Temperature Control)
Dans les modes TC Ni, Ti et SS, l‘appareil fonctionne avec des résistance ayant un l de résistance
en nickel (Ni200), en titane (Ti) et en acier inoxydable (SS316), dont la résistance est comprise entre
0,05 et 1,5 ohms. En mode TC, la température peut être comprise entre 100 °C et 315 °C (200 °C et 600 °F),
en fonction de la résistance utilisée.
38
Page 42
INNOCIGS ULTEX T80 – EXPLICATIONS RELATIVES AUX MODES DE FONCTIONNEMENT
Mode TCR (Coefcients de Température de la résistance)
Dans les modes TC Ni, Ti et SS, l‘appareil fonctionne avec des résistances ayant un l de résistance
en nickel (Ni200), en titane (Ti) et en acier inoxydable (SS316), dont la résistance est comprise entre
0,05 et 1,5 ohms. En mode TC, la température peut être comprise entre 100 °C et 315 °C (200 °C et 600
°F), en fonction de la résistance utilisée. Ce mode vous permet de sélectionner différents coefcients de
température pour le l et de faire fonctionner l‘appareil avec diverses valeurs de TCR.
Veuillez noter que la résistance utilisée doit être xée avant la première utilisation en mode TC/TCR.
39
Page 43
INNOCIGS ULTEX T80 – SÉLECTION ET UTILISATION DES MENUS
Commuter entre les modes de fonctionnement
Quand l’appareil est allumé, appuyez rapidement trois fois de suite sur le bouton d‘allumage. Appuyez sur
les touches « PLUS » / « BAS » pour naviguer entre les modes disponibles. Appuyez sur la bouton re pour
conrmer votre sélection.
Utilisation des menus
Appuyez simultanément sur le bouton d‘allumage et sur le bouton « Plus » pendant trois secondes pour
accéder au menu où vous souhaitez procéder à d‘autres paramétrages. Naviguez dans le menu à l‘aide des
boutons « PLUS »/« MOINS ». Appuyez sur le bouton d‘allumage pour accéder à un sous-menu. Naviguez
dans le menu correspondant à l‘aide des boutons « PLUS »/« MOINS ». Appuyez sur le bouton d‘allumage
pour conrmer votre choix.
40
Page 44
INNOCIGS ULTEX T80 – SÉLECTION ET UTILISATION DES MENUS
Exit
Appuyez de nouveau sur le bouton d‘allumage pour fermer le menu.
Afchage des sous-paramètres
Le menu SUBPARA vous permet de spécier si l‘écran, en mode normal, afchera le nombre
de bouffées (« Puff »), la durée totale de vapotage (« Time ») ou l‘ension électrique en
volts (« Volt »).
Vous pouvez réinitialiser les points de menu PUFF et TIME en maintenant la touche
« Plus » appuyée.
41
Page 45
INNOCIGS ULTEX T80 – SÉLECTION ET UTILISATION DES MENUS
Activation/désactivation de l‘afchage
Le menu STEALTH vous permet de spécier si l‘afchage doit rester allumé ou être éteint
durant le vapotage. Sélectionner « On » pour activer le mode STEALTH, « Off » pour le
désactiver.
Paramétrages de la fonction de préchauffage en mode VW
L‘appareil est doté d‘une fonction de préchauffage en mode VW. Le menu PREHEAT vous permet
de régler la fonction de préchauffage.« Pwr » vous permet de régler la puissance en watts et
« Dura » la durée en secondes. « Exit » vous permet de quitter le sous-menu.
Remarque :
Vous pouvez également utiliser la fonction de préchauffage dans les modes TC/TCR à température contrôlée.
Lorsque le mode TC/TCR est activé, appuyez sur le bouton d‘incendie quatre fois de suite rapidement. En
appuyant sur les touches de réglage « PLUS » / « MOINS », vous pouvez régler une puissance entre 1 et 80
watts. Appuyez sur la bouton re pour conrmer votre sélection. Avec cette puissance, l‘appareil commence
à fonctionner dans les modes température.
42
Page 46
INNOCIGS ULTEX T80 – SÉLECTION ET UTILISATION DES MENUS
Afchage de la version actuelle du matériel/micrologiciel
Le menu VERSION vous permet d‘afcher la version actuelle du matériel/micrologiciel.
Appuyez sur le bouton d‘allumage pour quitter l‘afchage.
Verrouillage de la résistance en mode TC/TCR
Le menu COIL vous permet de verrouiller (symbole : verrou fermé) ou de déverrouiller
(symbole : verrou ouvert) la valeur de la résistance pour le fonctionnement en mode TC/TCR.
Remarque :
1. Veuillez n‘utiliser la fonction de verrouillage qu‘à température ambiante, de telle sorte que la résistance
de base correcte puisse s‘afcher en mode Lock (verrouillage). Si ce n‘est pas le cas, cela peut entraîner des
résultats de mesure erronés, qui peuvent également avoir un impact négatif sur les fonctions de protection.
2. Si vous souhaitez utiliser par erreur des bobines conventionnelles en mode TC/TEMP ou TCR, qui ne
conviennent pas pour un vapotage à température contrôlée, ou si leur résistance est supérieure à
1,5 Ohm, l‘appareil passe automatiquement en mode VW.
43
Page 47
INNOCIGS ULTEX T80 – SÉLECTION ET UTILISATION DES MENUS
Spécication du coefcient de température en mode TCR
Le menu TCR vous permet de spécier les valeurs TCR pour les espaces mémoire M1, M2 et
M3. La plage de valeurs de TCR va de 1 à 999.
44
Page 48
INNOCIGS ULTEX T80 – MESSAGES D’ERREUR ET FONCTIONS DE PROTECTION
Protection contre les courts-circuits
Le message « ATOMIZER SHORT » s‘afche à l‘écran dès qu‘un court-circuit se produit sur la résistance.
Aucune résistance détectée
Le message « NO ATOMIZER FOUND » s‘afche à l‘écran si aucun atomiseur n‘est connecté.
Batterie faible
Si la tension de la batterie chute en deçà de 2,1 V, l‘appareil indique « WEAK BATTERY ». La puissance de
sortie est réduite pour être adaptée à la tension.
Recharger la batterie
Si la tension chute en deçà de 2,0 V, « BATTERY LOW » s‘afche à l‘écran. En appuyant de nouveau sur
le bouton d‘allumage, le message « BATTERY LOW LOCK » s‘afche et l‘appareil s‘arrête. Rechargez l‘appareil.
45
Page 49
INNOCIGS ULTEX T80 – MESSAGES D’ERREUR ET FONCTIONS DE PROTECTION
Résistance trop basse
Si la résistance de la bobine est en deçà de 0,05 ohm, le message « ATOMIZER LOW » s‘afche à l‘écran.
Protection de la température
Si, en mode TC/TCR, la température réelle de la bobine atteint la température de consigne, l‘écran afche le
message « PROTECT ». Vous pouvez continuer d‘utiliser l‘appareil tout à fait normalement.
Alarme de température
Si la température de l‘appareil est supérieure à 70 °C, l‘appareil s‘éteint automatiquement et le message
« DEVICE TOO HOT » s‘afche. Vous pouvez continuer de vapoter après avoir laissé l‘appareil refroidir.
46
Page 50
INNOCIGS – SERVICES DE GARANTIE ET RÉPARATIONS
Conditions de garantie
Tous les produits d‘InnoCigs sont soumis à un strict contrôle de qualité. Outre la garantie légale obligatoire,
vous bénéciez de 6 mois de garantie commerciale sur tous les produits InnoCigs. La période de garantie de
6 mois est valable à compter de la date d‘achat chez le revendeur spécialisé. La date indiquée sur le ticket de
caisse est déterminante. Pendant la période de garantie, les appareils présentant des défauts sont réparés
ou échangés par InnoCigs.
Les consommables tels que les embouts et les résistances sont exclus de la garantie.
Les appareils ou pièces échangés deviennent la propriété d‘InnoCigs. La prestation de services de garantie
n‘entraîne ni une prolongation de la période de garantie, ni le début d‘une nouvelle garantie.
47
Page 51
INNOCIGS – SERVICES DE GARANTIE ET RÉPARATIONS
Toute réclamation au titre de la garantie est exclue en cas de dommage dû à
- Non-respect des consignes de sécurité applicables à l‘appareil
- Non-respect du mode d‘emploi
- Usage de la force (p. ex. coup, choc, chute)
- Interventions n‘ayant pas été effectuées par des professionnels du service après-vente agréés par InnoCigs
- Tentatives de réparation de votre propre initiative
- Expédition dans un emballage ne garantissant pas la sécurité pendant le transport
Dans tous les cas de garantie, InnoCigs se réserve le droit de procéder à un examen précis avant de prendre
la décision nale. InnoCigs se réserve le droit de réviser les conditions de garantie.
48
Page 52
INNOCIGS – GARANTIE ET SERVICE APRÈS-VENTE
Garantie légale, garantie du fabricant et service après-vente
Si le produit ne fonctionne pas ou présente un défaut de quelque nature qui soit, veuillez tout d‘abord
contacter le revendeur spécialisé auprès duquel vous avez acheté votre appareil.
S‘il est nécessaire de faire valoir une garantie, veuillez procéder comme suit : contactez le service client
d‘InnoCigs par e-mail, par fax ou par téléphone. Vous pouvez sinon également recourir au service d‘échange
sur notre site internet www.innocigs.com.
Si vous avez des questions concernant le fonctionnement et l‘utilisation, merci de contacter notre service client.
INNOCIGS ULTEX T80 – COMPACT DEVICE WITH 80 WATTS, DISPLAY AND MENU NAVIGATION
Information for the User
Thank you for choosing a product by InnoCigs! We place great value on high quality and safety standards
across our entire range. We hope you enjoy vaping with your new e-cigarette product!
Read the usage instructions carefully before use in order to ensure correct use of the e-cigarette product
by InnoCigs. Use only original and/or recommended products in combination with this product. The
manufacturer shall not provide any service and/or warranty when non-recommended products are used
together with this product.
Should you have questions or need more information about your InnoCigs e-cigarette product please
contact your dealer or visit our website at www.innocigs.com.
Persons under 18 years, pregnant women, nursing mothers and people with cardiovascular disease should not use this
product. Not recommended for non-smokers. Please keep out of the reach of children.
This product must not be
used by minors.
This product complies with EU requirements on technical
goods and may be sold throughout the European Union.
This product must be kept
away from children.
This product must not be
used by pregnant or nursing
women.
Electronic goods and batteries should not be disposed
with normal household waste! Please dispose of used
electronic goods and batteries – as required by law – at
a municipal collection location, so that raw materials
and potentially harmful substances can be properly
removed and recycled.
53
Page 57
INNOCIGS ULTEX T80 – NOTES & PRECAUTIONS
User Instructions
1. If the device has been dropped, please check if any components have come loose, whether there is liquid
leakage, or whether there is any defect on your mouthpiece. If there are no signs of damage upon visual
inspection of the product, you can continue using the device. For hygienic reasons, please wipe the
mouthpiece with a cloth before reusing.
2. The device should not be used if there are cracks or deformations in the material or a defective part
needs to be replaced. Never attempt to repair the device on your own if a defect occurs.
3. The device should not be used when the e-liquid in the clearomizer tank is empty or almost empty. The
same applies if you experience a change in the taste. Please ll the Clearomizer tank with fresh e-liquid
and replace the head before you continue to use the e-cigarette. Because atomizer heads are wearing
parts, they must be changed regularly.
4. Never store the device in rooms with extremely high temperatures or in rooms with extremely high
humidity. Avoid long periods of direct sunlight.
5. The recommended temperature range for charging is 5°C to 45°C and for using the device is
-10°C to 60°C.
54
Page 58
INNOCIGS ULTEX T80 – NOTES & PRECAUTIONS
6. If e-liquid comes in contact with your skin, wipe it off as soon as possible and wash the area of contact.
7. If e-liquid is swallowed, contact your local poison control center. The Poison Emergency Hotline of the
Charité University Hospital Berlin can be reached day and night by phone at +49 (0)30 - 19 240. In
Austria, you can reach the 24h hotline of the Vienna Poison Information Center by phone at
+43 (0)1 - 406 43 43. In France, please contact one of the local poison control centers. In case of
emergency, immediately contact local emergency ofcials.
8. Nicotine can increase the heart rate and/or blood pressure. Nicotine can cause nausea, dizziness and/or
stomach pain. If you notice any undesirable side effects, discontinue use and consult a physician.
9. Please comply with all local laws when using this e-cigarette product.
10. The product must not be placed in the hands of children or adolescents.
Warning
This e-cigarette product can be used with nicotine-containing e-liquid. Nicotine is a highly addictive
substance.
55
Page 59
INNOCIGS ULTEX T80 – NOTES & PRECAUTIONS
General Information about Pufng Techniques while Vaping
When vaping, a distinction is made between two pufng techniques:
Moderate Vaping (Mouth-to-Lung)
The vapor from an e-cigarette is rst collected in the oral cavity for the entire duration of the puff and
then inhaled into the lungs. This pufng technique is referred to as moderate, mouth-to-lung vaping and is
similar to smoking. To achieve this, there must be a noticeable resistance when pufng on the e-cigarette.
Atomizer heads that support this pufng technique in the moderate range (resistance usually > 1 ohm) are
often referred to as MTL (mouth to lung) heads. (Other abbreviations include ML and M2L)
56
Page 60
INNOCIGS ULTEX T80 – NOTES & PRECAUTIONS
Sub-Ohm Vaping (Direct Lung Inhalation)
While pufng, the vapor of an e-cigarette is directly inhaled into the lungs. This pufng technique is referred
to as sub-ohm vaping with direct lung inhalation. To achieve this, there must be low pufng resistance and
a strong air supply to the atomizer head. Both have a positive effect on producing large quantities of vapor.
Atomizer heads that support this pufng technique in the sub-ohm range (resistance usually < 1 ohm) are
often referred to as DL (direct lung) heads. (other abbreviations include DTL and D2L)
57
Page 61
INNOCIGS ULTEX T80 – CONTENTS | DESIGN OF THE DEVICE
Contents of the Ultex T80 Box Mod
1x Ultex T80 Box Mod
1x QC USB Cable
1x User Manual
spring-loaded 510 Thread
Fire Button
Adjustment Button “+” (UP)
Adjustment Button “-” (DOWN)
OLED Display (0.49 Inch)
58
Micro USB Port
Battery Cover
Page 62
INNOCIGS ULTEX T80 – USING THE DEVICE
Operating Instructions
Fully charge the one necessary and replaceable 18650 battery before rst use. Please take note of the positive and negative poles in the battery compartment. Ensure that there is no visible damage to the surface of
the battery cell. The device has a 510-pin connection with a spring-loaded connector, making it suitable for
a variety of sub-ohm-capable clearomizers.
Tips for Cleaning
Use a dry cloth or cotton swab to clean the device.
Power On / Off
Press the re button ve times in rapid succession to turn the unit on and ve times to turn it off again.
We recommend that you switch off your device during transport and during long periods of non-use.
59
Page 63
INNOCIGS ULTEX T80 – USING THE DEVICE
Vaping
While holding the re button of your e-cigarette, inhale the vapor slowly and continuously through the
mouthpiece of your clearomizer. Release the re button while exhaling the vapor.
Lock/Unlock the “Up” and “Down” Adjustment Buttons
With the device turned on, hold down the “Up” and “Down” buttons simultaneously for two seconds until the
display shows “Key Lock.” The adjustment buttons are now locked. To unlock the buttons, hold them down for
another two seconds until the display shows “Key Unlock.” This function helps you avoid accidentally changing
your vape settings.
Charging and Updating the Device
The balanced charging system allows fast charging with a maximum charging current of up to 2 A. You can
charge the device via USB cable via a PC or with an external device into which you insert the battery.
Also connect the device for a software update via QC-USB charging cable with an internet-compatible PC.
60
Page 64
INNOCIGS ULTEX T80 – MAIN FEATURES & PERFORMANCE
InnoCigs Ultex T80 Key Data
Output Modes POWER (VW) | TC (Ni, Ti, SS316) | TCR (M1, M2, M3) | Bypass
Power Output 1.0 to 80 Watts
Voltage 0.5 to 9 Volts
Temperature Range 100°C to 315°C | 200°C to 600°F
Resistance Range 0.05 to 3.5 Ohm in POWER/Bypass Mode
0.05 to 1.5 Ohm in TC/TCR Mode
Charging Current max. 2.0 A
Diameter 26 mm
Height 95 mm
Thread Type 510
61
Page 65
INNOCIGS ULTEX T80 – REGULATING THE POWER OUTPUT & THE TEMPERATURE
General Operation to control the Power and Temperature Output
Depending on the atomizer head used, the power of the unit can range from 1 watt up to 80 watts and the
steam temperature can range from 100°C to a maximum of 315°C. Changing the wattage or temperature
also changes the taste and steam behavior. The higher the wattage or temperature is set, the more intense
the steam development will be. Press and hold one of the setting buttons to automatically increase or
decrease the wattage or temperature.
Switch between °C and °F
If you increase the temperature to 315°C and continue to press the right button, the temperature reading
will automatically change to the lowest Fahrenheit (200°F). Equally, if the temperature is set at the lowest
Fahrenheit (200°F) and you continue to press the left button, the temperature reading will automatically
change to the highest Celsius (315 °C).
62
Page 66
INNOCIGS ULTEX T80 – EXPLANATIONS TO THE VAPING MODES
POWER Mode (Variable Wattage)
Power mode supports atomizer coils in a resistance range between 0.05 ohms and 3.5 ohms. Depending on
head used, the power can be between 1 watt and 80 watts in VW mode.
Bypass mode
Bypass mode is a direct output mode in relation to voltage. A resistance range of 0.05 to 3.5 ohms is
possible in this setting to ensure error-free use. The output power is regulated automatically in relation to
the current battery status.
TC/TEMP Mode (Temperature Control)
In TC modes Ni, Ti and SS, the device supports atomizer coils with nickel (Ni200), titanium (Ti) and stainless
steel (SS316) windings, with resistances between 0.05 ohms and 1.5 ohms. The temperature can be between
100°C and 315°C (200°C and 600°F) in the TC Mode, depending on the atomizer head used.
63
Page 67
INNOCIGS ULTEX T80 – EXPLANATIONS TO THE VAPING MODES
TCR mode (Temperature Coefcient of Resistance)
In TCR mode (M1, M2, M3), the device supports atomizer coils with nickel (Ni200), titanium (Ti) and
stainless steel (SS316) windings, with resistances between 0.05 ohms and 1.5 ohms. The temperature can
be between 100°C and 315°C (200°C and 600°F) in the TC Mode, depending on the atomizer head used.
This mode allows you to select different temperature coefcients of the wire or to operate with different
TCR values.
Please note that the resistance of the vaporizer head used must be set before it is rst used in
TC/TCR mode.
64
Page 68
INNOCIGS ULTEX T80 – SELECTING & OPERATING THE MENUS
Switching between Operating Modes
Press the re button rapidly 3 times while device is switched on to change the current operating mode.
Navigate through the available modes by pressing the“UP”/”DOWN”-adjustment buttons. Press the re
button to conrm your selection.
Operation of the Menus
Press the re button and the “UP”-adjustment button simultaneously for approx three seconds to enter
the menu where you can make further settings. Use the “UP”/”DOWN”-adjustment buttons to navigate.
Press the re button to enter one of the submenus. Use the “UP”/”DOWN”-adjustment buttons to navigate
within the submenus. Press the re button to conrm your settings.
65
Page 69
INNOCIGS ULTEX T80 – SELECTING & OPERATING THE MENUS
Exit
Press the re button to leave the menu.
Display of Subparameters
In the SUBPARA menu you can specify, whether the number of puffs in total (“Puff”), the total
vaping time (“Time”) or the strength of electric tension in volts (“Volt”) is displayed on the
screen while normal operation.
In the menus PUFF and TIME you can reset the values by pressing and holding the
“UP”-Adjustment button.
66
Page 70
INNOCIGS ULTEX T80 – SELECTING & OPERATING THE MENUS
Display On/Off
In the STEALTH menu you can specify, whether the screen is activated or deactivated while
vaping. Choose “On” to activate or “Off” to deactivate” the screen.
Settings for the Preheat-Function (VW-Mode only)
The device is equipped with a preheat-function for the VW-mode. In the PREHEAT menu you can
specify the wattage (“Pwr”) and the duration (“Dura”) for the preheat-function.
Choose “Exit” to leave the PREHEAT menu.
Note:
In the temperature-controlled modes TC/TCR a preheat-function is available as well. Press the re button
four times in quick succession while TC or TCR-mode is activated. By pressing the “UP”/”DOWN”-
adjustment buttons you can select a power between one to 80 watts. Press the re button to conrm your
selection. With this power, the device starts to re in the temperature-controlled modes.
67
Page 71
INNOCIGS ULTEX T80 – SELECTING & OPERATING THE MENUS
Display of the recent Hardware/Firmware Version
In the VERSION menu, you can display your current hardware / rmware version.
Press the re button to leave the VERSION menu.
Lock/Unlock Coil in TC/TCR-Modes
In the COIL menu you can lock or unlock the recent resistance value for the TC/TCR-mode.
Choose the symbol of a closed lock to lock or the symbol of a closed lock to unlock the
resistance value.
Note:
1. This function should only be used at room temperature, to ensure that the correct
“base resistance” is locked.
2. If you accidentally use a conventional coil or coils with a resistance greater than 1.5 ohms in
TC-Ni, TC-Ti, TC-SS or TCR (M1, M2, M3) modes, the device will automatically switch to VW Mode.
68
Page 72
INNOCIGS ULTEX T80 – SÉLECTION ET UTILISATION DES MENUS
Setting of the TCR-Value (TCR Mode only)
In the TCR menu you can specify the TCR-Values for the memory locations M1, M2 or M3.
The TCR value range is between 1 and 999.
69
Page 73
INNOCIGS ULTEX T80 – ERROR MESSAGES & PROTECTIONS
Short Circuit Protection
The message “ATOMIZER SHORT” will appear on the display immediately if there is a short circuit at the head.
No Atomizer Head detected
“NO ATOMIZER FOUND” will appear on the screen when no atomizer is connected.
Weak Battery
If the voltage of the battery drops below 2.1 V, the device will display “WEAK BATTERY.” The output power
will be reduced adequate to voltage.
Recharge Battery
If the voltage falls below 2.0 V, “BATTERY LOW” will appear on the display. When the Fire button is pressed
again, “BATTERY LOW LOCK” will appear and the device switches off. Please recharge the device.
70
Page 74
INNOCIGS ULTEX T80 – ERROR MESSAGES & PROTECTIONS
Atomizer Low Alarm
If the resistance of the coil drops below 0.05 ohm in VW/Bypass modes or below 0.05 ohm in TC or TCR
mode, the display will show “ATOMIZER LOW.”
Temperature Protection
If, in TC/TCR mode, the actual temperature of the coil has reached the set temperature, “PROTECT” will be
shown on the display. You can continue to use the device as usual.
Temperature Alarm
If the temperature of the device rises above 70°C, it will switch off automatically and “DEVICE TOO HOT”
will appear on the display. You can continue vaping after the device has cooled down.
71
Page 75
INNOCIGS – WARRANTY & REPAIR
Warranty Terms
All products of InnoCigs are subject to strict quality control. You will receive, along with the legally required
warranty, a 6-month warranty on all InnoCigs products. The warranty period of 6 months applies from the
date of purchase from your dealer. The date on your sales receipt is decisive. During the warranty period,
devices that have defects will be repaired or replaced through the company InnoCigs.
Wearing parts such as mouthpieces and clearomizer heads are excluded from the guarantee.
Replaced devices or parts shall become the property of InnoCigs. The guarantee does not extend the
warranty period nor does it initiate a new warranty in transition.
72
Page 76
INNOCIGS – WARRANTY & REPAIR
Warranty Claims are excluded for Damage resulting from:
- Failure to comply with the safety notes of the device
- Not following the instructions
- Use of force (Ex: shock, impact, case)
- Submission of claims that have not been authorized through InnoCigs service addresses
- Unauthorized repair attempts
- Sending warranty repair in unsafe packaging
InnoCigs reserves in all warranty cases, the right to scrutinize the claim until the nal decision. InnoCigs
reserves the right to revise these warranty conditions.
73
Page 77
INNOCICS – WARRANTY & SERVICE
Warranty & Service
If the product ceases functioning or is defective in any way, please contact the specialist retailer where you
purchased the product.
If a warranty claim is necessary, please proceed as follows: Contact the InnoCigs customer service by e-mail,
fax or phone. Alternatively, you can use the exchange service on our website www.innocigs.com.
If you have any questions about the product‘s operation or its use, please do not hesitate to contact our
customer service department.