Smart Wireless BBQ Thermometer
IBT-6X
BBQ GO
Base
Put in the battery
Two AAA size batteries are needed for this device. Make sure they
are put in the right direction by following the icons on the unit.
Open the battery cover.
Put in batteries, noticing the icons
that show directions.
Lock the battery cover.
Download the APP
Search the keyword “bbq go” in Appstore or Google Play, or scan
the following QR code with your phone.
Download and install it for free.
Make sure your phone meet the requirements:
iPhone 4S, and later models;
iPod touch 5th, ipad 3rd generations and later models,
all ipad mini;
Android devices running version 4.4 or later, with blue-tooth
4.0 module.
Install the probes
The device will keep scanning the sockets when its power is
switched on, the Probe Indicators will blink one by one from 1 to 6
where probes are plugged in.
Then insert the probes into the food, make sure the front tip of the
probe is in the center of the food to get accurate temperature.
Pair with your phone
Keep the bluetooth switch of your phone on.
Launch the app, and follow the instructions
in the app to pair and activate the device.
Press and hold the power button on the
device for 3 seconds to power it on.
Connected successfully.
Once paired the device with your phone, you don’t need to do it
again, unless you change to other phones.
Bluetooth Indicator
No Icon
Icon Blinking
Icon Fixed
1
2
3
4
Probe 1
Probe 2
4
Enjoy your barbecue time
Power ON/OFF
Choose the food type and preference for the food where each probe
is inserted, the app and the device will display its current and target
temperature.
The user interface of the app may be changed when upgraded.
Please follow the instructions in the app.
Power ON:
Press and hold the power button for 3 seconds.
Power OFF:
Press and hold the power button for 3 seconds.
Auto-off after 8 hours out of connection with phone.
When the food is ready, the app and the device will alarm.
Options
Temperature
History
Preference
Display
Probe Number
Current
Temperature
Target
Temperature
Connection
Status
Timer
Preference
Setup
Device Setting
Warning
The heat resistance varies in different components of the probe,
DO NOT put the probes directly in the fire frame. And probes are
NOT dishwasher safe. Please DO NOT put the teflon cable and
the connecting part (between the sensor and teflon cable) into
the water.
App Store is a service mark of Apple Inc.
Google Play is a service mark of Google Inc.
Sensor
Teflon cable
With stainless steel mesh
(Length: about 120cm / 3.9ft)
0~250°C / 30~482°F
Non water-proof
This device complies with part 15 of the FCC Rules. Operation
is subject to thefollowing two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the
party responsiblefor compliance could void the user's authority
to operate the equipment.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for
help.
FCC ID: 2ALANIBT-2X
Inkbird Tech. C. L
Shenzhen, GD, 518000, China
www.ink-bird.com
cs@ink-bird.com
Loading...