Page 1
ASSEMBLY
INSTRUCTIONS
NT-WG1144
Wood and Glass TV Stand
Safety information and
specifications...........................................2
Tools needed ...........................................3
Parts ............................................................3
Hardware...................................................4
Assembly instructions ..........................5
Before using your new product, please read these instructions to prevent any damage.
Page 2
Safety information and specifications
Maximum weight: 135 lbs. (61.2 kg)
Maximum width: 1-inch overhang on each side
of the top shelf
Overall dimensions (W × H × D):
44 × 24.25 × 20" (111.8 × 61.6 × 50.8 cm)
Top shelf (W × D):
44 × 15" (111.8 × 38.1 cm)
Middle shelf (W × H × D):
34.88 × 9.39 × 16" (88.6 × 23.8 × 40.6 cm)
Bottom shelf (W × H × D):
34.88 × 9.5 × 18.5" (88.6 × 24.1 × 47 cm)
44" (111.8 cm)
15" (38.1 cm)
24.25" (61.6 cm)
18.5" (47 cm)
CAUTION: This stand’s glass work surface
is intended only for use with a product not
weighing more than 135 lbs. (61.2 kg) and
having a width that will permit it to sit
evenly on the stand with no more than a one-inch
overhang on each side on the top shelf. Using with
other products, including products that weigh more
than the maximum weight allowed or extend
beyond the maximum width, may result in instability,
which may cause possible injury.
Caution: This product contains small items that
could be a choking hazard if swallowed.
Keep these items away from young children!
Do not use the glass shelves to lift the stand. See
instructions for more details.
Model #: NT-WG1144
Distributed by Best Buy Purchasing, LLC
Manufacturer: Whalen Furniture Mfg. Inc.
Manufacture Date:
2
Still need help? Call 800-573-2860
Page 3
Parts
Tools needed
DrillNo. 2 Phillips screwdriver
A Top shelf frame (1)
B Middle shelf frame (1)
C Bottom shelf frame (1)
D Rear support (1)
E Left leg (1)
F Right leg (1)
G Top s helf (1)
H Middle shelf (1)
I Bottom shelf (1)
Package contents: parts
Note: You may receive extra hardware.
3
Still need help? Call 800-573-2860
Page 4
Hardware
Label Hardware Qty.
J1
K1
L19
M24
N6
P26
Left bracket
Right bracket
Suction cup
3/4" bolt
(19.05 mm)
1-1/4" bolt
(31.75 mm)
Lock washer
*A non-toxic touch-up pen has been
provided to repair any small nicks or
scratches that may occur during shipping
or assembly.
Label Hardware Qty.
Q26
R2
S1
T1
U1
Flat washer
Cable clip
Allen (hex)
wrench 4 mm
(0.158")
Touch-up pen*
Tipping
restraint
hardware
kit
Package contents: hardware
Make sure you have all the hardware necessary to assemble your new TV stand:
Video Instruction Guides: Go to http://init.showuhow.com to view step-by-step instructional
videos for assembling and installing your product. Enter the following product number on the
ShowUhow homepage - INTANY00004.
http://init.showuhow.com/VIGS/INTANY00004/tabid/5924/language/en-US/Default.aspx
1234in
4
10 20 30 40 50 60 70 80 90 1 00mm
Still need help? Call 800-573-2860
Page 5
Assembly instructions
Up
Corner
plates
M (8) N (2)
S (1)P (10)
Q (10)
Step 1 Attach the shelf frames (A, B, C) to the rear support (D). Make sure the inside corner plates on the shelf
frames will face up after assembly.
You’ ll ne e d:
Still need help? Call 800-573-2860
5
Page 6
Step 2 Attach the left and right legs (E, F) to the shelf frames. Make sure that the tops are flush with the wood front
M (6) N (4) S (1)P (10) Q (10)
rail on the top shelf frame (A).
You’ll need:
6
Still need help? Call 800-573-2860
Page 7
Step 3 Attach the left and right brackets (J, K) to connect the middle rails of the top shelf frame (A) with the rear
J (1) K (1) P (6) S (1)M (6) Q (6)
support (D).
You’ ll ne e d:
Still need help? Call 800-573-2860
7
Page 8
Step 4 Attach the cable clips (R) onto the rear support (D).
M (4) R (2) S (1)
TIP: You can use these cable clips to help keep your entertainment center’s cables organized.
You’ll need:
8
Still need help? Call 800-573-2860
Page 9
Step 5 Adjust the floor levelers on the bottom of both legs to level the TV stand.
Note: The floor levelers are
pre-attached on the bottom of
each leg.
Still need help? Call 800-573-2860
9
Page 10
Step 6 Attach the suction cups (L) firmly into the top holes and inside corner plates on the shelf frames (A, B, C).
L (19)
Install the glass shelves (G, H, I) with the black side of the glass down.
Tip : If a suction cup resists insertion, try pressing down on the middle of the cup with the hex wrench
while twisting it clockwise into the hole, as if you were screwing it in.
10
You’ll need:
Still need help? Call 800-573-2860
Page 11
Step 7Position the assembled stand against a wall where you plan to use it, then follow the instructions printed on
U (1)
Phillips screwdriver
Drill
the bag containing the tipping restraint hardware kit (
Note: You need a 3/8" drill bit to drill the hole for the wall anchor. The hole should be 1 1/2" deep.
U) to attach the restraint hardware to the wall and the stand.
You’ll need:
For customer service, call: 877-573-2860 (U.S./Canada markets)
Still need help? Call 800-573-2860
11
Page 12
www.initproducts.com
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave. South, Richfield, MN 55423 U.S.A.
© 2013 BBY Solutions, Inc., All Rights Reserved.
Init is a trademark of BBY Solutions, Inc. Registered in some countries.
All other products and brand names are trademarks of their respective owners.
V4 ENGLISH
13-0328
Loading...