INID NGRPAOLF User Manual

INID MultiSmart readers

Specifications

Typical read range

Technology distance
Mifare ISO card
LF Proximity ISO card

1)

Depends on transponder antenna geometry.

1)

Depends on LF technology and card antenna geometry.

Power Supply

7 - 24 Volt DC (12 VDC recommended)

Power consumption

model average peak

INID MultiSmart 1300 mW 1750 mW
INID MultiSmart PIN 1300 mW 2050 mW

Current consumption @12 VDC

model average peak

INID MultiSmart 110 mA 146 mA
INID MultiSmart PIN 110 mA 171 mA

3)

Use Ohm's law to calculate current at different voltages.

Interface

Inputs type and protection specifics
Outputs type and protection specifics

Dimensions

143 x 50 x 25 mm / 5.63 x 2 x 1 inch

Material

UL94-V0 rated LEXAN® 925U

Operating temperature

-25° to 65° C / -15° to 150° F

Protection class

IP54 Complete protection against contact,

protection against dust deposit. Protection
from splashed water.

1)

2)

60 mm 2.4 inch

30 – 60 mm 1.2 – 2.4 inch

3)

Cable specifications (non-shielded)

interface

Wiegand

maximum

cable length

meters feet mm

61 200
91 300

min.conductor size

with 12 V supply

2

2)

AWG

0.25 24

152 500 0.34 22

Clock/Data 25 80

TTL serial 1.5 5

RS232 2.4 8

RS485/RS422

(cable power)

RS485/RS422

(local power)

CAN bus system / speed dependent

2)

With a 24V supply, minimum conductor size is AWG 24 for all

interfaces and lengths.

61 200

152 500 0.34 22

1220 4000 0.25 24

0.25 24

Features

INID readers have a slim mullion mountable design
and are designed for both in- and outdoor use. The
INID reader can be mounted on any surface without
significant performance degradation. For mounting
to a metal surface however, a non-metallic spacer is
advised.
The switch mode power supply of the reader
accepts a wide range input from 7 - 24 VDC. Higher
input voltages result in lower current consumption
and allow for cost effective wiring with a smaller
conductor diameter.
Reader output formats are determined by the
personalization of the card and/or configuration of
the reader.
Separate models are available for card-only and
card+PIN.
Electrical interface options for WG/C&D/TTL serial,
RS485/RS422, RS232 and CAN bus are available
with separate models.

PIN code

INID PIN readers provide extensive options for PIN
data formats and output protocols. The card and
PIN code data is sent separately and independently
allowing host system determined operation for card­only, PIN-only and card and PIN usage.

Indications

User feedback is provided by a single LED bar and a
multi-tone sounder. User feedback is controllable by
the host system. PIN models are equipped with
back lighting of the PIN code digits for usage in
dark environments.

Operation

When a proximity card is read successfully the card
associated code is send to the Host system, the LED
bar lights briefly and the sounder sounds a short
tone.
When a PIN is entered the data is transmitted; at
each key press a click sound is produced and the
LED bar lights briefly. The back light of the PIN code
lights up after a successful card read or at the first
key press.
The LED bar or individual LED bar segments and the
buzzer are also controllable by the Host system.

INID MultiSmart readers - installation and operation manual version 1.02; March 16, 2012

Connector Assignments

Wiegand / Clock and Data / TTL serial

500-5005 INID MultiSmart reader WG/C&D/TTL
500-5045 INID MultiSmart PIN reader WG/C&D/TTL

1 LED 1 - Green 5 BUZZER RXD
2 LED 2 - Amber 6 TAMPER
3 D1 DATA TXD 7 GND
4 D0 CLOCK TXE 8 POWER

RS485 / RS422

500-5015 INID MultiSmart reader RS485/RS422
500-5055 INID MultiSmart PIN reader RS485/RS422

1 LED 1 - Green 5 RS485 n.c. RS422 RX­2 LED 2 - Amber 6 RS485 n.c. RS422 RX+
3 RS485 TRX+ RS422 TX+ 7 GND
4 RS485 TRX- RS422 TX- 8 POWER

Caution:

Ensure all communication lines are properly biased and terminated.

floating communication lines may cause spurious emissions.

RS232

500-5025 INID MultiSmart reader RS232
500-5065 INID MultiSmart PIN reader RS232

1 LED 1 - Green 5 RTS
2 LED 2 - Amber 6 RXD
3 CTS 7 GND
4 TXD 8 POWER

CAN bus

500-5035 INID MultiSmart reader CAN bus
500-5075 INID MultiSmart PIN reader CAN bus

1 LED 1 - Green 5 n.c.
2 LED 2 - Amber 6 n.c.
3 CANL 7 GND
4 CANH 8 POWER

Parts list

1 Reader front qty: 1
2 Terminal connector qty: 1
3 Mounting backplate qty: 1
4 Enclosure screw qty: 1
5 Installation sheet qty: 1

Installation instructions

1 Determine an appropriate position for the reader

and drill two holes for mounting the backplate
and one hole for the cable, see diagram for
measurements. Do not mount readers less than
20 cm (8 inches) apart.

2 Pull the cable trough the hole in the backplate

and mount the backplate. Protect the cable
against sharp edges and any damage from
chafing.

3 Remove the terminal connector from the front of

the reader. Prepare the end of the cable and
wires, eliminate any loose or frayed strands. Keep
the wire ends as short as practical.

4 Connect the wires to the connector according to

the reader type. Wire ends, termination resistor
leads and optional permanent links shall be kept

as short as possible.
5 Place the connector on the reader pins.
6 Place the reader front over the hinge of the

backplate and close the reader (see diagram),

keeping the wiring in the lower part of the reader

housing. DO NOT use excessive force, retract the

cable if necessary.
7 Test the reader: apply power and present a valid

card. The LED bar should flash and the sounder

should produce a short tone indicating a

successful read. If the Host system is connected

to LED bar and sounder inputs these should

follow the functionality of the Host system.
8 The reader front should now be secured to the

backplate using the supplied enclosure screw.

This device contains 2 transmitters

Certifications

CE, FCC

FCC ID: YAB-ISOACRDR (model 50XX) 13.56 MHz

YAB-NGRPAOLF (model 40XX) 115 – 148 kHz

Compliance statement

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received,

including interference that may cause undesired

operation.
Warning (part 15.21)
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
This in particular is applicable for the antenna which has
been delivered with the reader.

Consult your National Authority if any authorization
is needed for this product.

For mounting, use only flat head screws with a
maximum shank size of 4 mm (5/32”, #7)

INID MultiSmart readers - installation and operation manual version 1.02; March 16, 2012

INID BV

Mariëttahof 27
2033 WS Haarlem
The Netherlands
Phone: [phone]
Web: www.inid-readers.com