Ingrasys M2210E, M2210V User Manual

Download

M2210E / V

User’s Manual

Version 1.1

Table of Contents

Important Notices – Read Before Use ............................................................................ 2

Overview ......................................................................................................................... 2

Package Contents ............................................................................................................ 3

Installation ....................................................................................................................... 4

Hardware Installation ....................................................................................................................................................... 4

Software Installation ........................................................................................................................................................ 8

Discover IP Cameras ........................................................................................................................................................ 8

Assigning IP Address to the device ................................................................................................................................. 8

Discovering devices in Windows Networ k .................................................................................................................... 10

ActiveX add-on Installation ........................................................................................................................................... 11

Accessing the camera .................................................................................................... 13

Viewing the live video ................................................................................................................................................... 13

The Live view page ........................................................................................................................................................ 15

Video ............................................................................................................................. 17

Network Configuration ................................................................................................. 24

Recording ...................................................................................................................... 29

Event management ........................................................................................................ 34

Configuration of Event Handling ................................................................................................................................... 34

Examples of Event Handling ......................................................................................................................................... 39

System options .............................................................................................................. 41

Troubleshooting ............................................................................................................ 45

Check firmware version ................................................................................................................................................. 45

Upgrade device firmware ............................................................................................................................................... 45

Recover device settings .................................................................................................................................................. 47

LED Indicators ............................................................................................................................................................... 48

Technical Specifications ............................................................................................... 49

Important Notices

– Read Before Use

This instruction m anual is intended for administrators an d users of the Ingrasys M2210 Series IP Camera, including instructions for using and managing the camera on your network. The use of video surveillance devices can be prohibit ed by laws t hat vary from country to countr y. It is the user’s responsibili ty to ensure that the operation of such devices is legal before installing this unit for surveillance purposes.

Heed all warnings

Before installing the IP Camera, please read and follow all the s afety and opera ting instructio ns to avoid any damages caused by fault y assem bly and inst allat ion. T he user mus t adhere to all the warn ings on the pr odu ct and in this manual.

Liability

Every reasonable care has been taken in the preparation of this instruction manual. We cannot be held responsible for any technical or typographical errors and reserves the right to make alterations to the product and manuals without prior notice. We make no warranty of any kind with regard to the material contained within this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. The user should verify the relevant information is current and complete before placing orders. All products are s ol d s ubjec t to our terms and conditions of sale at th e t im e of or d er acknowledgement.

We shall not be liabl e nor respons ible for the applicati ons and resa le of its products or bundled sof tware with statements different fr om or beyond the specific ation/parameter s stated by us. W e are under no obligation to provide any further technical support service or product/software alteration beyond our representation.

Trademarks

All names used in this manual and products are probably registered trademarks of respective companies.

CE/FCC Statement (EMC)

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules which are designed to provide reasonable pro tec ti on ag ains t such int er f erenc e when the equipment is operated in a commercial environment. If the equipment is not installed and used in accordance with the instruction, it generates, uses, and can radiate radio frequency energy which may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his/her own expense will be required to take whatever measures may be required to correct the interference.

Overview

Ingrasys M2210 Series is a Full HD, compact IP camera specially designed for buses, trains, and other

vehicles applications. The camera comes with 3-axis mechanism design that allows users to adjust the camera's viewing angle for increased installation flexibility.

Capable of rugged RJ/M12 Ethernet connector & IP67-rated housing can against shock, vibration, humidity and dust. The M2210 Series is also embedded with 802.3af compliant PoE, ePTZ and all-in-one mechanism for easy installation.

Package Contents

M2210(E/V) Product CD Quick Installation Guide

Warranty Card Lens Tool VIP Card (Optional)

Hardware Pack

Installation

Hardware Installation

Connectors

Connections

Connect the camera to a PoE switch with an Ethernet cable.

Install RJ-45 Field Installable Feed-Through Adaptor for M2210E

Assemble RJ-45 field installable through adaptor to achieve system waterproof and vibration proof.

1. Assemble the through the field installable feed-through

adaptor and insert a stripped Ethernet cable.

2. Follow the pin definition to crimp the RJ-45 plug onto

the cable.

3. Connect to M2210E RJ-45 rugged Connector and fully

seal the connector to achieve waterproof and vibration proof completely.

Install M12 Field Installable Feed-Through Adaptor for M2210V

Assemble M12 field installable through adaptor to achieve system waterproof and vibration proof.

1. Insert a stripped Ethernet cable through the Sealing Nut and Housing of the field installable feed-through adaptor.

2. Follow the pin definition to weld the cable to the connector.

3. Connect to M2210V M12 rugged connector and fully seal the connector to achieve waterproof and vibration proof completely

Mount Camera

Alignment Sticker on drill holes

Loosen 2 screws and remove the top cover

3. Route the Ethernet cable through the hole and fasten camera on the surface with 4 screws

Tuning lens direction and focus

1. Fit the lens adjustment tool to the lens h older to adjust the direction of the lens. The tilt range is 0°~90° and the pan range is ±60°.

2. Pull out the lens adjustment tool, and turn it around to fit the lens to adjust focus.

3. Replace the top cover to finish installation.

Software Installation

Discover IP Cameras

Discovery Tool is a utility provided for not only searching and displaying the available IP cameras information in a network but also managing the multiple networking settings such as static IP address assignment.

After completing the hardware installation, run ingrasysDiscovery.exe to search for the IP camera installed.

Assigning IP Address to the device

The steps of applying this search tool are described as below.

1. Launch IPCAM Discovery Tool (ingrasysDiscovery.exe)

2. Assign IP address

The selection is based on a single or multiple camera devices.

[Set IP]

This is applied to one specific camera selected from the Device List.

Step1: Select one specific camera device

Step2: Input desired IP information

The default settings of ac count /password are Admin / Admin. If that were been changed, p lease enter the set values.

[Auto Set IP] This is applied to a group of specific cameras selected from the Device List.

Step1: Select specific cameras

Step 2: Input Account / Password

The default account infor mation is Admin / Admin. If the valu es have been re-set, please en ter the set values.

Step 3: Input IP information

Discovering devices in Windows Networ k

If the IP camera is installed in a ne twork with DHCP and UPnP ser vices, after obtaining an IP ad dress from DHCP server, it can then be discovered in “Windows Network” of a client PC, see figure below. The reason for being automatically disco vered is that the IP camera’s UPnP is default enab led (see Network



Network

Connectivity).

NOTE:

The term “Windows Network” in given figure above is used in Windows Vista / 7. It can be referred to Windows XP “My Network Places” which possesses the same capability of discovering UPnP devices.

Right-click on t he device and selec t “Properties”, the pop-up windo w shows all the inf ormation related t o the device, including the w eb access info. Use the web address to connect to t he IP camer a. Or simply doubleclick on the selected device, which gets immediately access to the camera webpage.

To identify the cam era from the listed devices in “Net work ”, utilize the UPnP name and the device’s MAC address. This MAC address can be found on the label.

ActiveX add-on Installation

It is recommended to use Internet Explorer 8 or later as the primary browser to access the IP cameras website. The first-time access to the camera webpag e will be prompt ed to install the ActiveX. To allow the ins tallation, click “Install” on the message bar and follow the instructions to complete ActiveX installation.

When the installation is completed, IE browser can display the live video of the IP camera as the below figure.

NOTE:

If, however, there is not any prompted message or ActiveX cannot be installed at all, it is needed to change the IE security level and settings.

<Example> Internet Explorer 9: Internet Options  Security  Custom level Ensure the “Download signed ActiveX controls” setting is either “Enable” or “Prompt” selected.

Accessing the camera

Viewing the live video

With the correct installation and I P settings, the camera device can be approac hed via network. There are three ways to view the live video from the camera,

1. Internet Explorer

- Launch IE browser and input the IP address of the camera or

- Click on “Browse” button on the selected IP camera address from Ingrasys Discovery Tool.

NOTE:

Ingrasys IP cameras also s upport the other web browsers for viewing the l ive video such as Firefox , Google Chrome or Safari.

2. RTSP Player

The live video of the camera can be played with RTSP players, such as VLC or QuickTime. The camera supports two simultaneous video streaming (see Video & Audio  Video Setting). To

gain access to the cam era for each vide o stream, the RTSP URL will be required. T he default paths for the 3 streams are “stream1”, “stream2” and “stream3”. The URL format should be input as below.

Stream1: rtsp://Camera_IP/stream1 Stream2: rtsp://Camera_IP/stream2 Stream3: rtsp://Camera_IP/stream3

The example given below is the live video displayed with QuickTime player.

3. NVR / CMS Software

Ingrasys IP cameras are ONVIF conformant products. Most of ONVIF conformant NVR / CMS software can retrie ve the video from the cam eras for both live view a nd recording. For more details about the support information and operation, please contact the soft ware ve ndor s.

The Live view page

The following illustration shows you the front page of Ingrasys IP camera website.

Live Video Window

Live Window

Quick Functional Buttons

OSD

Quick Index

Video Stream Operations

Snapshot: Press the button to capture an image photo

Record: Press the button to start recording. Press again to stop it.

Record Path: set up a file path that video clips and snapshots can be stored.

Full screen: Press the button to enter the full screen mode. Press ESC key to return.

Manual trigger: Press the button as triggering an event. See Event Manag ement for detail.

Digital Zoom: toggle the digital zoom function.

Video Stream Operations

Language selection for the WEB UI

Select video stream for displaying on live vide o window

Display the video in actual (configured) size or digital (scaled)

Select the preferred streaming protocol on th e client

Video

This section describes how to configure the video streaming of the device, and the related camera image configurations. Users with Administrator or Operator authority (see System



User Management) would

intend doing these configurations. Click on “Setup” of Quick Index to enter the Video page shown as below.

There are 2 sub-settings under “Video”:

− Camera Setting

− Video Setting

Camera Setting

Image Setting

Brightness: the luminance of image view. Default value is 8; adjustable from 0 to 16. Contrast: the ratio of luminance of white to black. Default value is 8; adjustable from 0 to 16. Saturation: colorfulness of a color related to its own b rightness. Def ault value is 8, adjus table from 0

to 16. Sharpness: refer t o image acutance, whic h pres ents i n th e e dges contrast of an i mage. Default value

is 8, adjustable from 0 to 16.

The 4 correlates are ref erring image appe arance in terms of color/vision that is a djustable according to user preferences.

Video Orientation: change the image orientation

• Mirror: rotate the image horizontally

• Flip: rotate the image vertically

NOTE:

These operations are us ually applied when cam era must be installed in a n exceptional position. F or the example of ceiling installation, camera must be installed upside-down.

Day/Night

Day/Night Mode:

Switch the video images for Day (plenty of light) or Night (Low light) scene. In default “A uto” mode, camera will switch to Day or Night vision according to the light intensity. The Day / Night modes contain 2 actions: switching IR Filter On / Off, and image hue Color / Mono.

In day mode, the IR f ilt er is s witched in to avoid the image sensor from r eceivin g t he inf rar ed, t hus t he true color image is provided. W hen camera enters night mode, IR filter is switched off to allow IR illuminations going into t he s ensor, thus increas ing the im ages light lev el. The im age c olor is s witched to B/W (Mono mode).

Nightmode Enhancement

With this function enabled, the better night vision will be obtained. However, the number of FPS may drop depends on the actual environmental illuminations.

Switch Time

The value reflects the delay time for both ways of day and night switch.

Advanced Setting

AC Frequency: Anti-flicker setting for environment with fluorescent light sources, image sensor

needs to fit the frequency of light (power) source. For instance, the power frequency is 50Hz for most European countries, while 60Hz is typically for US. This setting is therefore regionally different.

TV OUT: Option of NTSC or PAL. White Balance: The selections for different lightening condition, which is refereeing to color

temperature. The default value is set to AUTO. Flickerless Mode: Flickering c an also pr esent in various ex posure l evel. Set “Flicker less” Mode “O n”

to fix the maximum shutter speed (auto exposure control). Thus, the flickers can be eliminated. Exposure & Gain Mode: Select auto / manual Expos ure & Gain contro l mode. T he selection def ines

the controlling in a range of or fixed value, according to the f ollowing two items (Shutter Speed and

Gain Value). The configurations will be limited at selected maximum rates when AUTO mode is on. Max. Shutter Speed: Also refer to the exposure t ime. Higher shutter speed is norm ally applied under

strong light circums tance, so the image won’t be overexposure. Lower shutt er speed, on the other hand keeps image luminance in low light environment.

Max. Gain Value: Also refer to the amplification factor for the incoming light. Increasing the gain value provides a brighter image, but the noises may also be increased.

WDR: Enable this function for image objects under backlight circumstances. Exposure Level: Adjust Exposure level for a target level of sensed brightness. Auto exposure

function will adjust to exposure time to make the sense image brightness close to the target.

NOTE

The “Shutter Speed”, “Gain Value” and “WDR” can be configured for daytime and nighttim e. The configurations will be applied according to the current status of “Day/Night Mode“.

: represents the Day mode : represents the Night mode The setting items with the Day or Night mode symbol will be altered along with the setting of

Day/Night mode. The examples are illustrated as below.

Video Setting

Video Stream

This tab provides detailed stream configurations. These settings can affect video size, quality. The maximum transmission performance can be expected under the condition of full network bandwidth.

The camera supports up to 3 video streams. Each stream can be configured with following items.

Video Format: H.264, MPEG4 and MJPEG are available for the selection. The demand of bandwidth and storage requirement differs from the selection of video format. In the request of same video quality, H.264 contributes to less bandwidth and storage requirement, which can be more efficient than MPEG4 or MJPEG.

Resolution: The resolution here describes an image size counted in width by height, e.g. 1280x720, referring to pixel resolution. The available resolutions for Stream 1 to Stream 3 are listed in the following table.

Resolution Stream 1 Stream 2

Stream 3

1920 x 1080

1280 x 720

800 x 450

V V V

640 x 360

V V V

480 x 270

V V V

320 x 180

V V V

“V”: available

“

-“: not available

The table for Stream 1 to Stream 3 enable list.

Stream 1 Stream 2

Stream 3

1920 x 1080 @30FPS

1920 x 1080 @15FPS 800 x 450 @15FPS

1920 x 1080 @10FPS

800 x 450 @10FPS

1280 x 720 @30FPS

1280 x 720 @15FPS 800 x 450 @15FPS

1280 x 720 @10FPS

800 x 450 @10FPS

800 x 450 @30FPS

800 x 450 @15FPS

800 x 450 @10FPS

“-“: not available

Frame Rate: configure the maximum frame rate in video streaming. Higher frame rate gives a better video in terms of smoothly moving objects/scenes. However, this would result in higher bandwidth and storage requirement.

Intra Frame Period: is applied only in MPEG4 / H.264 which the video stream is composed of Iframes (full image information) and P-frames (motion-compensated difference information). This setting configures the Intra Frame Period which is the time period between 2 I-frames. The shorter period means the higher frequency of I-frame. Video can then be well handled while bit rate may increase.

Video Quality: There are two types of bit rate controls for vid eo quality adjustment, Constant Bi t Rat e (CBR) and Variable Bit Rate (VBR).

CBR mode concerns about the circum s tanc es of f ixed data rate transf err ing. However, VBR is ut il i zed when network bandwidth is less concerned.

NOTE:

CBR is not applicable in MJPEG video mode.

Video Overlay

The camera supports stamping text information on the video images. The options of the date/time string or/and a line of text message (e.g. camera name or location) are available for displaying on the images.

Privacy Mask

Privacy Mask can block out the specific areas from view. The blocked areas wi ll n ot be seen in both live view and recorded video clips and the total of 8 profiles can be created to the list.

To create Privacy Mask, simply input Privacy Mask Name and click “Add New” button and then apply it to complete the addition.

Network Config ur at i on

The IP Camera acts as one of the network devices. It allows user to c onfigure the network functionaliti es based on applicatio ns. This section will describe the network configurations. Fundam entally, for instance, the IP as signment of the device can be done via DHCP server, static IP option or PPPoE to obtain IP from the service provider.

There are 5 subdirectories in “Network”:

− Network Type

− Network Connectivity

− Quality Service

− Access Port

− Access IP Filter

Network Type

There are 3 ways to configure address for the IP camera device, including DHCP, Static IP and PPPoE.

Enable DHCP Service: The def ault setting is D HCP, which cam era will be a utomatic ally given an IP

address (IPv4/IPv6) in a network with DHCP server. Use Static IP: Camer a may also be manual ly assigned with a s tatic IP address (IPv4/IPv6). Subnet

mask, Gateway and DNS s erver(s ) will also ne ed to b e specified f or certain ne twork function prop erl y executed.

Enable PPPoE S ervice: This service is usually provi ded by an ISP (Internet Service Provider). IP Camera can establish a dial-up connection to the ISP and then get connected to Internet. (Only IPv4)

NOTE1:

If you would like to connect camera with IPv6 address, please note that this only works if your network environment and hardware equipment support IPv6. The browser should be Microsoft® Internet Explorer 6.5, Mozilla Firefox 3.0 or above.

NOTE2: (Link with IPv6 address as following steps)

1. Go to Setup -> System -> System Information page (under IPv4) to know the IPv6 address

2. Open your web browser to input the IPv6 address in the address bar.

3. The format should be: http://[2014:db8:0:1:2e0:d8ff:fe0c:adef]/

4. Press Enter key to open the Live View page of camera. For example

Network Connectivity

This page provides the connectivity configuration, so that IP camera can be accessed without nec es s arily providing the numerical IP addres s .

Enable UPnP Service: with UPnP enabled, IP camera device can be easily discovered in Windows Network (My Network Places). See “Discover devices in Windows Network” in previous section.

Enable DDNS Service: By registering this sort of service, camera can be assigned and accessed over Internet with a hostname instead of IP address. To enable the services, visiting the website of the service provider and registering an account are required.

Dyndns.org:

http://www.dyndns.com/

DHS.org:

http://www.dhs.org/

Quality Service

Quality Service provides network traffic management to guarantee the quality of services in higher priority, especially when network is insufficient. DSCP (Different Service Code Point) is a 6-bit IP header which defines the service level of the pac k et. According to the DS CP va lue, routers with PH B ( Per-Hop Behavior) will define a specific class of traff ic for the packet, in term s of bandwidth, latenc y, or loss rate, etc. Enable QoS and set DSCP value for the service to ensure its quality to be maintained.

NOTE:

To make the QoS function work, all the switches and routers in the network must support QoS.

Access Port

This page provides the ports configuration for requesting the services from the camera device. These services include Web Page access, HTTP and RTSP streaming services.

HTTP port / HTTPS port: By default, the HTTP and H TTPs ports are set to 80 and 443 respectivel y. They can also be assigned to another port number between 1025 and 65535.

The HTTP port is b asically provided f or device’s webpage ac cess. When the v ideo format is set to MJPEG, user is able to retrieve the live video via HTTP URL, e.g.

Http://<ip_address>/operator/get_video.cgi?channel=[1, 2] , where channel is to specify stream1 or stream2 RTSP port: RTSP (Real-Time Stream ing Protocol) is used to contr ol the live media stream ing. This port is

provided to request the s treaming service. By defau lt, t he por t number is set to 554. It can also be as s i gne d t o another port number between 1025 and 65535.

Multicast: Multicast is a streaming method with bandwidth conserving technology. By delivering a single video stream to multiple network clients, the bandwidth utilization can be reduced.

Select the Always multicast option to enable multicast for stream 1 ~ 2. Multicast Group Address – Set the IP address f or mult icast stream ing. T he Multicas t IP addres s m ust be in

the range from 224.0.1.0 to 239.255.255.255.

Multicast Ports – Set the port for multicast streaming. Multicast TTL – T he multicast T ime-To-Live (TTL) gives the range of routers that multicast traffic can pas s

through in the networks.

NOTE:

The multicast stream can b e trig gered b y a ne twork cli ent (e. g. ch oosing “ Mult icas t” f rom the li ve vie w page) whereas “Al ways Multicast” option is not enabled. This mechanism is k nown as “Multicast On Demand”. In this mode, multicast stream starts when one or more clients request. It stops automatically when the last client leaves t he multicast group. “ Always Multicast”, on the other hand, starts or stops multic ast stream by enablin g/disabling this func tion. It doesn’t m atter whether there is client request or not.

Access IP Filter

This setting also prov ides a bas ic securit y by filter ing the acc esses f rom other ho sts. Enab le this func tion an d choose “Allow / Deny” of the listed IP addresses. Up to 15 IP address can be added in the list.

Recording

This section provides the recording configuration on the camera. Unlike the recording function (Q uick Functional Butt on) on the live vie w page, video can als o be recorded to the storage attached to the local network storage (Samba) according to a time based schedule.

There are 4 subdirectories in the “Recording” category:

− Recording Plan

− SD Storage

− SD File List

− Samba

Recording Plan

Recording Plan List

It lists the created/scheduled recording plan(s). The details of a recoding plan include:

Plan Name: Identifier of the recording plan Status: Enable or Disable the recording plan Mon ~ Sun: Displays the hours in days of a week that recording is effective Src. (Source): The video source selected to be recorded

Dest. (Destination): The stored path for the recording file Remove: Click to delete this recording plan.

Add / Edit Recording Plan

Plan Name: Identifier of the recording plan Video Source: The selection of the video source to be recorded. Options: Stream1 / Stream 2 / Stream 3. Maximum File Size: This option defines the maximum file size of each video clip. Destination: The stored path for the recording file Select All: 24 hrs/ 7days (Mon-Sun) continuous recording Scheduled Pattern: User-defined time frame

Network Fail

You may enable this option for starting record to SD card if network connection is failed.

SD Storage

This page shows the SD card information when it is attached to the IP camera.

Normally, inserting the m icro SD card will be done before enteri ng this page and obtain t he card informat ion as below. However, if it is the other way around, click SD storage tab to refresh it.

SD Card Status:

• Syncing: Display when the card database is in the process of synchronization

• Ready: Display when the micro SD card has been detected successfully is in a ready state

• Detached: Display when there is no micro SD card detected

• Recording: The micro SD card is being recording recorded

• Remove button: Remove the micro SD card

• Mount button: Mount the micro SD card

Used (%): Display the used space in percentage. Click Refresh button to obtain the up-to-dated value Disk Format: Click Format button to format the micro SD card

NOTE:

1. It is recommended to inser t the micro SD card bef ore powering up the system . This is to ensure that the attached device is properly detect ed in the initial stage.

2. When the card storage is full, the system will automatically launch overwrite process from the earliest recording files.

SD File List

This page provides the search of records. The SD storage may contain both “triggered-by-schedule” recordings and “triggered-by-events” snapsh ot / v id e o. T her e are s ear ch c ondit i ons used t o n arr o w down the search results.

The latest 10 Records

The most recent 10 records are listed in this table. Each record name is a link to view this video or image. Following the “Record Name”, each record is listed with its “Trigger Type” and “Record Size” details

Searching the Records

The SD storage would keep massive records after the “recording plan” and/or “event handling” (see Event Management) has been launched. The search criteria are provided to look for particular records in the SD

card.

Example: Trigger Type – Schedule Recording

There are 3 categories of search criteria:

1. Trigger Type: It includes Motion Detection, Manual Trigger, Network Fail and Periodically as the type of

“triggered-by-events” and Schedule Recording as the type of “triggered-by-schedule”.

2. Trigger Time:

Input Date / Time rage that recording was created.

3. File Type:

Select the file type that is either video clips (.avi) or pictures (.jpeg) or both.

NOTE:

The search criteria can be multiple selected for each searching. For instance, the search result can be the combination of Network Fail and Digital Input.

Samba

This page allows user to configure the file stor age via Sam ba. To begin with it, click Enable Sam ba and then input the related information.

NOTE:

Samba can only support m ount ing a s hared f old er loc ated in the root directory. For ex ample, to mount a folder called “Shared” can be input the path as below.

\\<IP>\Shared

Event management

Event management describes the handling of events w ith the correspo nding actions. A common case can be exampled is storing a captured image to a local storage (Actions), when there is a Motion Event (Trigger Condition). This chapter gives the configurations of Triggers (what to detect?) and Actions (“what to send” a nd “where to send”). A time based schedule can also be applied.

Configuration of Event Handling

There are 3 subdirectories in the “Event” category. The 3 configuration groups are correlated. A completed event setting may need to configure each part in sequence.

− Event Server & Media

− Motion Configuration

− Event List

Event Server & Media

The “Event Server” is the configuration of “where to send”, e.g. FTP server, while Media is the sending file type. The combination of file type and the remote servers will then be applied as an event action.

Event Server List

Click on “Add New” button to add the remote severs. These are email recipients and FTP server.

Server Name: Identifier of the event server Server Type

Email: Send the media file via email when an event is trigger ed.

• Mail Server Address: Enter a host name or IP address of the email server.

• User Name: Enter the user name of the email account.

• Password: Enter the password of the email account.

• Server Port Number: Enter the server port of the mail server. The default is 25.

• Sender’s E-mail Address: Enter the email address of the sender

• Mail Subject Prefix: Enter the subject description for the mail.

• SSL/TLS : Select None/SSL/TLS for secure your mail transmission

• Receiver Table: Enter the recipients’ email address. The mail can be sent to up to 5 recipients.

FTP: Send the media file to a FTP server when an event is triggered.

• FTP Server address: Enter the FTP server’s address.

• User Name: Enter the user name of the FTP login account.

• Password: Enter the user name of the FTP login password.

• Server Port Number: Enter the server port of the FTP server. The default is 21.

• Upload Path: Enter the file path that files will be sent to.

Media Type There are 2 types of media (file) available, snapshot (.jpg image) and video clip (.avi).

Video Source: Select the video source to be captured Pre-alarm / Post-alarm image(s): Ent er the num bers of images that will be capt ured bef ore and af ter trigger

is activated. Pre-alarm / Post-alarm record: Enter the numbers of seconds that video will be recorded before and af ter

trigger is activated.

Maximum file size: Define the maximum file size that a video clip is generated.

Motion Configuration

There are three MD (Motion De tection) ar eas ca n be enab led. Each MD c an b e i ndividua ll y enabled/disabled, defined the covering range and trigger sensitivity.

To enable and verified the MD, follow the steps provided below.

1. Check the box to enable the motion area

2. Drag and drop to move the motion window

3. Hold and drag any corner of the rectangle to resize the window.

4. By dragging the pin of the slider bars, adjust the detection “Sensitivity” and “Object Size” of the rectangle covered area.

NOTE:

By name implying, t he “Sensitivity” setting means the s ensitivity level to the motion detection; the higher value given makes the motion window more sensitive to the moving object. “Object Size” stands for the percentage threshold of moving object size verse motion window size. For example, the “Object Size” set as 50 that m eans the “size of de tected m oving object” must larger tha n 50% of the motion window to trigger the motion event.

5. The status chart shows the m otion activ ities. When the motion vector exc eeds a threshol d (the Obj ect Size), the motion trigger is activated. The index number of “Show in chart” reflects the number of Motion Area.

6. To enable other motion area, repeat above steps.

7. Click on “Apply” button to save the settings.

Event List

List a summary of configured events. That is the selection of trigger condition(s) and the corresponding actions, as well as the scheduling. Up to 10 event objects can be configured.

To begin with it, click on “Add New” button to extend for the detailed configurations.

Event Name: Enter an event name, e.g. Motion Detection, to identify this configured event. Select All: 24 hrs/ 7days (Mon-Sun) continuous recording Scheduled Pattern: User-defined time frame Triggered by: This describes the selection of trigger conditions which include:

• Motion Detection: Select the m otion detection area(s) used f or trigger con dition. To enab le and

configure the motion detection areas, go to Motion Configuration.

• Manual Trigger: Enable the system to detect the user input action (press the alarm button,

on the live view page).

• Network Fail: Enable the system to detect the network connection status.

• Periodically: Enable the system to perform the set Action periodically

Action: The selection of responding actions

• Upload files to a server: There are two dr ag-down selections, Event Server and M edia Type.

The Event Server indicates the file destinati on such as local network storage Sam ba, and the file type includes snapshot image and video clip. For t he snapshot / video cl ip configurations, go to

Event Server & Media.

NOTE:

The dependency of Even t Ser ve r and Media Type is described as below.

‐ When Event Server is either Samba or SD card, the selection of Media Type will be

either Image or Video

‐ When Event Server is either Mail or FTP, the selection of Media Type will only be

image

Examples of Event Handli ng

The following cases are provided as the examples of Event Handling.

Scenario

While viewing live video, user can manually trigger an e vent anytime simply by pressing the button,

on the web page. It will send email to the specified email accounts with the captured pictures.

The configurations are illustrated as below:

Step 1: Add Event Server

• Go to Event  Event Server & Media  Event Server List

• Click on “Add New”

• Choose “Email” and fill in the email server and recipients’ information.

Step 2: Configure Media Type

• On the same web pa ge, configure the Media Type. For the following exam ple, the system is

configured to capture 1 picture before (pre-alarm) the event and 2 pictures for the event and after (post-alarm) . For video clip, pre-alarm and post-alarm could be configured for event video record.

• Click on “Apply” to save the email server and media settings.

Step 3: Configure Event List

• On Event List page, click on “Add New” button.

• Enable and configure this event

• Click on “Apply” to save the settings of this page.

- Event of manual triggering -

a. Click the check box to enable this event. b. Give a name of this event setting; e.g. MTrigger.

This is an identity of event handling.

c. Choose “Select All” for 24 hrs/ 7days (Mon-Sun),

as this event is required to be triggered anytime.

d. Select “Manual Trigger” as this event’s trigger

source. This will activate manual trigger button in the live view.

e. Click the check box to enable the function and

select “Mail” for Event Server and “Image” for the Media Type

b c d

System options

System Options provide us ers to obta in and conf igure the s ystem settings of the IP camera system. It contains the page of System Information, Date and Time, User Management, Maintenance and Log Service. The details about each subcategory will be described as below.

System Information

The page gives the general information of the IP camera system.

In System Status, the Model ID, Firmware Version and MAC Address are list ed. The Camera Name and Location fields are revisable to identify a unit among multiple cameras installed.

The IP address information of this IP camera is listed in Netw ork Status. T he RTSP Status field shows t he video stream(s) being requested by the listed client(s).

Date and Time

This section describes the date/time adjustment for the IP camera system. The ways to adjust the IP camera’s date/time can be Synchronize with NTP Server, Synchronize with PC or Set Manually.

Current Date & Time

Display current system date/time of the IP cam era. The date format can be cha nged from the drop-do wn list under Configure Date & Time.

Current Date & Time Keep Current Date & Time: The option of keeping current date and time, not to be adjusted. Synchronize with NTP Server: Automatic date/time adjustment. The IP Camera must be able to access to

the given NTP server (e.g. time.windows.com).

NOTE: To apply “synchronize with NTP Server”, a Time Zone must be selected for referencing to the local time.

Synchronize with PC: The PC linked to the web page of the IP camera can also be a date/time synchronizer.

However, if the PC is link ed from a time zone which is different from the one where camera is installed, t he web page will pop up a warning message for time zone difference.

Set Manually: Manually adjust the date / time. Date & Time Display Format: The system date can be displayed in the format of DD/MM/YYYY,

MM/DD/YYYY or YYYY/MM/DD. The system time can be displayed in the format of 12H or 24H Time Zone: Select an appropriate time zone for local where IP camera is installed. The automatic

adjustments will be applied based on the selected time zone. Click the “Daylight Saving Time Enable Automatically” checkbox to enable the daylight savi ng function and user could select the day light saving start time and end time based on the DST rule where camera installed.

User Management

By default, the access to the camera is not user authenticated. For security, the IP camera should be restricted only authenticated accounts to access. It is able to enable/disable user accounts, as well as to manage the added users in this page.

Initially, there is a default account, Admin in the “User List”. To enable this account, click on “Enable Authentication” a nd t hen a ppl y. T o edit p asswor d for the d efault account, click “Edit” to enter th e conf igurati on window.

To create a new account, click “Create User” button. Enter Account / Password for this account with the group type on the “Create account” window.

The user account with “ Administrator” authentication can do al l the config uratio ns. “Operator” has the sa me rights as Administrator, exc ept for User M anagement. “Viewer” is allowed o nly the acces s to live view page. Up to 8 user accounts can be added in the User List.

Maintenance

This page provides tools for camera system maintenances.

Reboot: Restart the camera system Restore to Factory Default: Restore camera f actory default settings. The networ k setting can be kept by

checking the “Except Network Type” checkbox. Backup Configurations: The system settings can be backed up and exported to a file. The file can be

applied to upload the previous user settings to the camera, or other cameras.

NOTE:

The backup file can be applied to other Ingrasys I P cameras , so users won’t ne ed to configure each device. It is recomm ended to switch the IP setting to DHCP m ode before exporting the backup f ile. Otherwise, all IP cameras will have the same IP address.

Firmware Upgrade: There may be new released fir mware for features update or issues fixed. T o upgrade the firmware for the s ystem, retrieve the firm ware image file, import to the s ystem and then do the upgrade process.

LOG service

The system operations and / or process will be reco rded in the log system. The link provides the review of these records.

System Log: It contains records of system changes such as login failed or link on/off. Event Log: It records the log message of triggered event, for instance, motion detection is asserted. Parameter List: It lists all the system parameters with the current value.

Troubleshooting

Check firmware version

Firmware version m ay imply the func tionaliti es’ update s or availa bility in th e cam era system. Therefore, in th e first step of troubles hooting and then reporting, it he lps to locate the found issu es. Newer version firmware may have these issues corrected.

The version code can be found in Setup -> System -> System Information, see figure below.

Upgrade device firmwar e

Firmware upgrade proc ess should be don e via the web conf iguration: Setup -> System -> Maintenance -> Firmware Upgrade. Before the process, read the instructions and release notes coming with each new

released version.

[Read Before Upgrade]

1. The latest firmware image is available on our official website.

2. Make sure all other client connections are disconnected and current jobs such as recording are required to terminate.

3. During the upgrading period, DO NOT disconnect the pow er of the camera. Otherwise the unit might be damaged.

[Steps of Firmware Upgrade]

1. Go to firmware upgrade page on the web. Figure 1

2. Click “Firmware” button to load the firmware image. Figure 1

3. Click “Upgrade” to begin (the upgrade progress bar will pop up). Figure 2

4. Once it is done, the system will reboot automatically.

5. Go back to firmware upgrade page and confirm if the “current version” is up-to-dated. Figure 3

Figure 1

Figure 2

Figure 3

Recover device settings

In some cases, camera system does not respond to any operation. A certain recovering processes would help to get the unit back to initial status, so that it can resume operable / configurable. This will be the oper ati ons on the “Reset Button”.

1. Restart / Reboot the device

Press reset button within 5 second; the system will be restarted.

2. Reset User Management

Short pin 3 and pin 4 of the terminal block for 5~9 seconds; User management settings will be reset to default and the system will be restarted.

3. Reset to factory default settings

Short pin 3 and pin 4 of the terminal block for over 10 seconds; the system will be reset to factory default and the system will be restarted.

LED Indicators

There are 2 type of LED indicators; LED for Network Status (green) and LED for system and power (bicolor, blue and orange). These LEDs can help to recognize the current device status.

1. LEDs for Network Status:

Green

Cable Disconnect

OFF

10 Link / Traffic (Activity)

Flashing

100 Link / Traffic (Activity)

Flashing

2. Bicolor LED indicator for Power & System Status:

Blue

Orange

Power On / System Reboot Steady ON Steady ON Initial Process Ready Flashing 3 seconds OFF

Normal Operation

Steady ON

OFF

Firmware Upgrade

OFF

Flashing

Internal (Hardware) Failure

OFF

Steady ON

Technical Specifications

*Design and specifications are subject to change without notice.

Types of camera

Model No. M2210E/V‐F3.6

Description 2MP Full HD Mini‐Dome IP Camera

System Information

Processor ARM based 32‐Bit RISC Processor

Flash 32MB

RAM 128MB

Camera

Image Sensor 1/2.7" progressive scan CMOS sensor

Maximum Resolution 1920 x 1080

Lens type Board lens, Fixed IRIS

Focal Length f=3.6mm

Aperture F1.8

Field of View H=77°, V=54°, D=100.2°

Min illumination 0.5Lux

Shutter Time 1/7 sec. to 1/30,000 sec.

Video

Video Compression H.264 / MPEG4 / MJPEG

Maximum Video Stream 3 simultaneous streams

Maximum Frame Rate

H.264: 30fps@1920 x 1080

MPEG4: 20fps@1920 x 1080 MJPEG: 20fps@1920 x 1080

Bit Rate Mode Constant Bit Rate(CBR)/Variable Bit Rate (VBR) bit rate control

Image Orientation Mirror, Flip

Image Setting

Exposure Mode: Auto/Manual,

White Balance Mode: Auto/Fixed, Gain Mode: Auto/Manual Configurable Sharpness, Saturation, Brightness, Contrast with 17 levels (0‐16).

Privacy Mask Support 8 privacy mask zones.

OSD Time Stamp and Text caption overlay.

Network

Users Live view for up to 6 clients.

Ethernet 10Base‐T/100Base‐TX

ONVIF Supported

Supported protocols

IPv4, IPv6

, TCP/IP, HTTP, HTTPs, UPnP, RTSP/RTP/RTCP, IGMP, FTP, DHCP,

DNS, DDNS, PPPoE, NTP, SMTP, Bonjour, QoS, Multicast

Event Management

Event Triggers Motion detection, Manual trigger, Network Fail ,Periodically Trigger

Event Actions

File upload via FTP, SMTP and SAMBA and Micro SD Card;

Notification via FTP, email ; Video and audio recording to SD or SAMBA.

I/O Connectors & Indicators

Network Connector

RJ45 Ethernet connector(M2210E) M12 Ethernet connector(M2210V)

Power Input PoE (IEEE 802.3af class 3)

Power Consumption 5W max

LED indicator

1 x Networking status (Green)

1 x System status (Blue & Orange)

Reset Reset button on board

Memory Card Micro SD/SDHC card slot

General

Weight Net: 460 g (1.017 lb)

Dimensions Ø4.89” x 1.65" / Ø114mm x 41.8mm

Operating temperature ‐10°C ~ 50°C (14°F~122°F)

Storage Temperature ‐20°C ~ 60°C (‐4°F~140°F)

Operating Humidity 20% ~ 90% RH Certifications CE, FCC (class A), EN50155

OS Microsoft Windows XP/ Vista/ 7/ 2K

Browser Microsoft IE 8.0 or above, Chrome, Firefox, Safari

Other Value-added Features

Software Free bundled 32CH software

Water Resistant IP67

Package Contents Component

1 x Hardware pack

1 x Quick Installation Guide (QIG) 1 x Warranty Card 1 x Product CD (Camera discovery tool, User's manual,Recording software) 1 x Lens adjustment tool

Ingrasys M2210E, M2210V User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual