G2334H/E
Ver: v1.00
Quick Installation Guide
Ingrasys Technology Inc.
G2334H/E Quick Installation Guide
v1.00
www.ingrasys.com
G2334H/E
Package Contents
A
Cable Management Bracket
C
Product CD
F
Warranty Card
H
Power Adapter (Optional)
J
VIP Card (Optional)
I
01
Sunshield & Screws Pack
B
Alignment Sticker / Desiccant Bag
D
Waterproof Connector for
RJ45 Ethernet Enclosure
E
Quick Installation Guide
G
Ingrasys Technology Inc.
Physical Description
Lens
Light Sensor
IR LED
02
RJ45 Cable
Reset Button
Micro SD/SDHC Card Slot
Focus Assist Button
TV Out Connector
System LED
I/O Terminal Block
DC12V Power Terminal
AC24V Power Terminal
Pin Denition
1 GND
2 Digi Out
3 GND
4 Digi In
5 GND
6 Digi In
7 485+
8 485-
9 AGND
10 Line Out
11 AGND
12 Mic In
G2334H/E Quick Installation Guide
v1.00
www.ingrasys.com
Hardware Installation
03
2. Lock the housing by burglarproof screw.1. Attach the sunshield with two supplied screws.
4. Fix Wall bracket holder on the wall.3. Attach the alignment sticker to the wall and drill three holes.
6. Feed the function cable through the front opening
of the wall mount bracket.
5. Install the intersection bracket to the side of
the Network Camera with two screws.
1 2
3 4
5 6
Ingrasys Technology Inc.
Hardware Installation
1
2
Horizontal Pan
Vertical Tilt Adjustment
04
2. Use wrench to lock bracket with housing.1. Push the spring mortise and hook the bracket onto
the groove of the wall mount bracket.
4. Adjust the angle of wall mount bracket to aim
at shooting area.
3. Hang the wall mount bracket on the plate and x it
with the supplied screws.
7 8
9 10
1
2
G2334H/E Quick Installation Guide
v1.00
www.ingrasys.com
1. Disassemble the components of waterproof connector into parts (A)~ (E) as show below.
2. Remove the rubber stopper from the bottom of the network camera and secure the screw nut (A) tightly. If you need
extra power for external devices or external devices such as sensors and alarms, please feed the cable through the wall
mount bracket and the waterproof connector (E --> C --> B --> A) as the illustration shown below.
(Note: There are three holes on the seal (B), the recommended cable gauge is 6.2mm)
Cabling Assembly – Waterproof Connector
05
Assembling Steps
(A) Sealing Nut (B) Seal (C) Claw (D) Pin (E) Sealing Nut
(A)
(B)
(C)
(E)
1
2
※
Recommended to use CAT-5 Cable (Φ6.2 ) for DC12V, AC24V or I.O function.
Ingrasys Technology Inc.
Cabling Assembly – Waterproof Connector
06
3. Push the seal (B) in to the claw (C) and insert the pin (D) into the empty holes on the seal (B) to avoid moisture.
4. Secure the sealing nut(E) tightly.
(B)
(C)
(D)
(E)
3
4
G2334H/E Quick Installation Guide
v1.00
www.ingrasys.com
(A) Sealing Nut
(B) Seal
(C) Screw Nut
(D) Housing
(E) Gasket
Cabling Assembly – RJ45 Cable Connector
07
1. Attach the gasket to the front of the housing.
Components of the Waterproof Connector
Assembling Steps
(E)
(D)
2. Insert the seal into the housing.
(D)(B)
3. Insert the stripped Ethernet cable through the sealing nut, screw nut and housing. Then, clamp the cable with
an RJ45 plug.
(A)
(C)
1 2
3
Ingrasys Technology Inc.
Cabling Assembly – RJ45 Cable Connector
4. Connect the Ethernet cable into the RJ45 cable.
5. Connect the housing into the RJ45 cable.
6. Insert the housing into the screw nut.
7. Screw the sealing nut tightly.
RJ45 Cable Dimension
4 5
6 7
08
13/16"-28UN
58.5mm
355 20mm
G2334H/E Quick Installation Guide
v1.00
www.ingrasys.com
Connections
1. Identify the type of network device.
2. If the network device supports PoE (Power over Ethernet) function, simply connect the camera to it via
Ethernet cable
3. If not, connect the network device (via Ethernet cable) to AC or DC adapter are required.
09
Ingrasys Technology Inc.
To adjust the zoom factor and focus range
The camera comes with a vari-focal lens. Focus Assist Button allows users to adjust the camera focus with precision by a
simple click.
Step 1 : Adjust the Zoom range, T W for a proper view angle.
Step 2 : "Press" Focus Assist Button
● Rotate the lens focus clockwise or anticlockwise to either end (N or ∞).
● Press and hold the button for 3 seconds until LED indicator ashes from Green light to Amber light
Step 3 : Adjust Focus
● Keep the camera pointing to the same scene during the tuning process.
● Start tuning the focus controller in the range of N ∞ shown on the lens.
● If LED displays Red light, it indicates the opposite turning direction.
Step 4 : Get the Best Focus Value
● When camera gets precise focus, the LED will become Green ashing.
● Remain the camera's pointing direction until the LED becomes steady Green.
Focus controller (N or ∞)
Zoom controller (T
W)
Focus Assist Button System LED
10
G2334H/E Quick Installation Guide
v1.00
www.ingrasys.com
How to install Desiccant Bag to IP Camera
(only for G2334E)
Use the double tape to attach the desiccant bag on the housing which marked in circle.
11
Ingrasys Technology Inc.
Assigning IP address
1. Launch Ingrasys Discovery Tool (IngrasysDiscovery.exe). The tool will start searching for cameras and then displaying
them on the Device List after being found.
2. Check the checkbox to select a camera device from the list.
3. The IP Camera may be assigned with a valid IP address via DHCP server. It can be also manually given a static IP address.
To do so, click on “Set IP”, and then input the IP, Subnet Mask and Gateway. Input account info if the camera is protected by
password. (Default ID/Password : Admin / Admin)
4. Click on the “Browse” button to get access to the camera web page immediately.
12
G2334H/E Quick Installation Guide
v1.00
www.ingrasys.com
Accessing the camera
1. Launch IE browser and input the IP address of the camera, or click on “Browse” button on Ingrasys Discovery Tool.
The web page with video will then be shown as below.
2. The live video of the camera can be played with a RTSP player, such as VLC or QuickTime. The network URL is
rtsp://Camera IP/stream1. The example given below is the live video displayed with QuickTime player.
13
Ingrasys Technology Inc.
Loading...