Inglis IRQ226300, INQ225300, IMQ225300, IKS203304, IKS203303 Owner’s Manual

...

REFRIGERATORUSE &CAREGUIDE

p p

GUIDED'UTILISATIONETD'ENIl TIEN DUREFRIGERATEUR

Tableof Contents/Tabledes matibres

ASSISTANCE OR SERVICE ............................. 1

REFRIGERATOR SAFETY ............................... 2

INSTALLATION INSTRUCTIONS .................... 3

REFRIGERATOR USE ...................................... 5

REFRIGERATOR CARE ................................... 8

TROUBLESHOOTING ...................................... 9

PRODUCT DATA SHEETS ............................ 11

WAR RANTY .................................................... 12

Assistance or Service

If you need assistance or service, first see the "Troubleshooting" section. Additional help is available by calling f-800-807-8777,

or write:

Whirlpool Canada LP

Customer Interaction Centre

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Information may also be obtained by visiting our website at

www.inglis.ca.

Please include a daytime phone number in your correspondence. Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation date for in-warranty service.

ASSISTANCE OU SERVICE ........................... 13

SleCURITle DU RleFRIGleRATEUR ................ 13

INSTR UCTIONS D'INSTALLATION .............. 14

UTILISATION DU RCFRIGCRATEUR ............ 17

ENTRETIEN DU RleFRIGleRATEUR .............. 19

DlePANNAGE .................................................. 20

FEUILLES DE DONNleES

SUR LE PRODUIT .......................................... 23

GARANTIE ....................................................... 24

Write down the following information about your appliance to help you obtain assistance or service if you ever need it. You will need

to know your complete model number and serial number. You can find this information on the model and serial number label, located on the inside wall of the refrigerator compartment.

Dealer name Serial number

Address Phone number

Model number Purchase date

2315507

Toorder replacement filters, call 1-800-807-6777 and ask for the part number listed below or contact your authorized Whirlpool

dealer. Stainless Steel Cleaner and Polish: Order Part #4396095

Standard Base Filter Cartridge: Order Part #4392857 (NL300 and L500)

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

mPlug into a grounded 3 prong outlet. mDo not remove ground prong.

mDo not use an adapter. mDo not use an extension cord.

mDisconnect power before servicing. mReplace all parts and panels before operating. mRemove doors from your old refrigerator.

SAVE THESE INSTRUCTIONS

_,Use nonflammable cleaner. _,Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

_,Use two or more people to move and install refrigerator. _,Disconnect power before installing ice maker (on ice maker

kit ready models only).

_,Use a sturdy glass when dispensing ice or water (on some

models).

ProperDisposalofYourOldRefrigerator

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily climb inside.

INSTALLATIONINSTRUCTIONS

NOTE: It is recommended that you do not install the refrigerator near an oven, radiator, or other heat source. Do not install in a location where the temperature will fall below 55°F (13°C).

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Remove packaging materials. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove

tape or glue. These products can damage the surface of your

refrigerator. For more information, see "Refrigerator Safety."

When Moving Your Refrigerator: Your refrigerator is heavy. When moving the refrigerator

for cieaning or service, be sure to protect the floor.

Always pulI the refrigerator straight out when moving it. Do not wiggle or "walk" the refrigerator when trying to move it, as floor damage could occur.

important information to know about glass shemvee

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping. For your protection, tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use special care when removing them to avoid impact from dropping.

__JL

1/2" (1.25 cm)(

II -- I!

Electdcam Shock Hazard

Pmuginto a grounded 3 prong outlet.

Do not remove ground prong, Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can reeumt in death, fire, or electricam shock.

r_ ..... /_

2" (5.08 ore}

Expmosion Hazard

Keep flammable matedams and vapors, such as gaeomine, away from refrigerator.

Faimureto do so can resumt in death, expmosion, or fire.

To ensure proper ventilation for your refrigerator, allow for 1/2"

(1.25 cm) space on each side and at the top. When installing your refrigerator next to a fixed wall, leave 2" (5.08 cm) minimum on

each side (depending on your model) to allow for the door to swing open. If your refrigerator has an ice maker, allow extra space at the back for the water line connections.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an extension cord.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF and then

disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting.

Gathertherequiredtoolsandpartsbeforestartinginstallation. Readandfollowtheinstructionsprovidedwithanytoolslisted

here.

TOOLS NEEDED:

• Flat-blade screwdriver • %" Drill bit

• 7/16"and 1/2"Open-end or two • Hand drill or electric drill adjustable wrenches (properly grounded)

• 1/4"nut driver

NOTE: Your refrigerator dealer has a kit available with a 1/4" (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 3/16"

(4.76 mm) saddle valve which reduces water flow and clogs more easily.

IMPORTANT:

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain above freezing.

Water Pressure

A cold water supply with water pressure of between 30 and

120 psi (207 - 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 - 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 - 414 kPa). If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 - 414 kPa):

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill after heavy usage.

• If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water Filtration System."

If you have questions about your water pressure, call a licensed, qualified plumber.

Determine the length of copper tubing you need. Measure from the connection on the lower rear corner of refrigerator to

the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

Using a grounded drill, drill a 1/4"(6.35 mm) hole in the cold water pipe you have selected.

....................A

G ............................B

............ C

A. Cold waterpipe E.Compression sleeve B.Pipe clamp F.Shutoff valve C. Copper tubing G.Packing nut D.Compression nut

6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the 1/4"(6.35 mm)

drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so the washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw the compression

nut onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear.

Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut. Do not overtighten.

3. Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help prevent

damage to the tubing when the refrigerator is pushed back against the wall.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

Read all directions before you begin. IMPORTANT: Ifyou turn the refrigerator on before the water line is

connected, turn the ice maker OFR

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Locate a 1/2"(12.70 mm) to 11/4'' (3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

Make sure it is a cold water pipe. Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

A. Tube clamp B. Copper tubing

The ice maker is equipped with a built-in water strainer. Ifyour water conditions require a second water strainer, install it in the 1/4"(6.35 mm) water line at either tube connection. Obtain

a water strainer from your nearest appliance dealer.

C. Compression nut D. Valve inlet

Style 2

1. Unplug refrigerator or disconnect power•

2. Remove and discard the shipping tape and the black nylon plug from the gray, coiled water tubing on the rear of the

refrigerator•

3. If the gray water tube supplied with the refrigerator is not long enough, a 1/4"x 1/4"coupling is needed in order to connect the

water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns, Do not overtighten.

A B C

A. Refrigerator water tubing

B.Nut (provided)

C. Bulb

D E F G

E•Ferrule (purchased) F. Nut (purchased)

G. Household water line

D. Coupling (purchased)

Turn shutoff valve ON,

Check for leaks, Tighten any nuts or connections (including connections at the valve) that leak,

Style 3

1. Unplug refrigerator or disconnect power•

2. Remove and discard the shipping tape and the black nylon plug from the gray, coiled water tubing on the rear of the refrigerator•

3. Thread the provided nut onto the water valve as shown. NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns, Do not overtighten.

Complete the Installation

Electrica_ Shock Hazard

PBug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or eiectrica_ shock,

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See the "Water and Ice Dispensers" section•

NOTE: Allow 24 hours to produce the first batch of ice, Allow 3 days to completely fill ice container.

REFRIGERATORUSE

For your convenience, your refrigerator controls are preset at the factory• When you first install your refrigerator, make sure that the

controls are still preset, The Refrigerator Control and the Freezer Control should both be set to the "mid-settings."

FREEZER

, 2

REFRIGERATOR

• 3 4

A•Bulb B.Nut (provided)

Turn shutoff valve ON,

Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak,

COLD

COLDER

COLD 1 6 COLDER

IMPORTANT:

• Your product will not cool when the REFRIGERATOR Control is set to OFE

• The Refrigerator Control adjusts the refrigerator compartment temperature, The Freezer Control adjusts the freezer compartment temperature, Settings to the left of the mid-

setting make the temperature less cold. Settings to the right of the mid-setting make the temperature colder•

• Wait 24 hours before you put food into the refrigerator. If you add food before the refrigerator has cooled completely, your

food may spoil.

NOTE: Adjusting the Refrigerator and Freezer Controls to a higher (colder) than recommended setting will not cool the compartments any faster.

Adjusting Controls

Give the refrigerator time to cool down completely before adding

food. It is best to wait 24 hours before you put food into the

refrigerator. The settings indicated in the previous section should be correct for normal household refrigerator usage. The controls are set correctly when milk or juice is as cold as you like and when

ice cream is firm. If you need to adjust temperatures in the refrigerator or freezer,

use the settings listed in the chart below as a guide. Wait at least 24 hours between adjustments.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm REFRIGERATOR Control

one setting higher

FREEZER too warm/ FREEZER Control too little ice one setting higher

REFRIGERATOR too cold REFRIGERATOR Control

one setting lower

FREEZER too cold FREEZER Control

one setting lower

The control can be adjusted to properly chill meats or vegetables. The air inside the pan is cooled to prevent "spot" freezing and can

be set to keep meats at the National Livestock and Meat Board recommended storage temperatures of 28° to 32°F (-2 ° to 0°C).

The convertible vegetable/meat drawer control comes preset at the lowest meat setting.

To store meat:

Set the control to one of the three MEAT settings to store meat at its optimal storage temperature.

To store vegetables:

Set the control to VEG to store vegetables at their optimal storage

temperatures.

NOTE: If food starts to freeze, move the control to the left (less cold). Remember to wait 24 hours between adjustments.

Cut Hazard

Use a sturdy grass when dispensing ice or water. Failure to do so can result in cuts.

Depending on your model, you may have one or more of the following options: the ability to select either crushed or cubed ice,

a special light that turns on when you use the dispenser, or a lock option to avoid unintentional dispensing.

NOTE:

• Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

• If your model has a base grille filter system, make sure the base grille filter is properly installed.

• The dispensing system will not operate when the freezer door is open.

• After connecting the refrigerator to a water source, flush the water system by dispensing water into a sturdy container until

you draw and discard 1.5 gal. (5.4 L) of water, or for approximately 3 minutes after the water begins dispensing. The flushing process cleans the water system and clears air from the lines. As the air is cleared from the lines, water may

spurt out of the dispenser. Allow several hours for the refrigerator to cool down and chill

water. Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

You can control the amount of humidity in the moisture-sealed crisper. Adjust the control to any setting between LOW and HIGH.

LOW (open) for best storage of fruits and vegetables with skins. NIGH (closed) for best storage of fresh, leafy vegetables.

The Water Dispenser

IMPORTANT: Dispense enough water every week to maintain a

fresh supply.

To Dispense Water:

1. Press a sturdy glass against the water dispenser lever.

2. Remove the glass to stop dispensing.

The Ice Dispenser

The dispensing system will not operate when the freezer door is open. Ice dispenses from the ice maker storage bin in the freezer

when the dispenser lever is pressed. NOTE: Some models dispense both cubed and crushed ice.

Before dispensing ice, select which type of ice you prefer. For crushed ice, cubes are crushed before being dispensed. This

may cause a slight delay when dispensing crushed ice. Noise from the ice crusher is normal, and pieces of ice may vary in size. When changing from crush to cube, a few ounces of crushed ice will be dispensed along with the first cubes.

To Dispense Ice:

1. Press the button to select the desired type of ice.

2. Press a sturdy glass against the ice dispenser lever. Hold the glass close to the dispenser opening so ice does not fall

outside of the glass. IMPORTANT: You do not need to apply a lot of pressure to the

lever in order to activate the ice dispenser. Pressing hard will not make the ice dispense faster or in greater quantities.

3. Remove the glass to stop dispensing.

The Dispenser Light

The dispenser area has a light. It can be turned on manually by

pressing the ON button (touchpad or rocker switch). On some models: Whenever you use the dispenser, the lever will

automatically turn the light on.

LIGHT

OFF ON

NOTE: See the "Changing the Light Bulbs" section for information

on changing the dispenser light bulb.

The Dispenser Lock (on some models)

2,' __

Your dispenser can be turned off for easy cleaning or to prevent unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the product, to

the ice maker, or to the dispenser light. It simply deactivates the

dispenser levers. The ice and water dispensers will not work.

• Press the LOCK button to lock the dispenser.

• Press and hold the LOCK OUT button a second time to unlock the dispenser.

Removing and Replacing Ice Storage Bin

1. Pull the covering panel up from the bottom and then slide it back toward the rear.

2. Lift the wire shutoff arm so it clicks into the OFF (up) position. Ice can still be dispensed, but no more can be made.

3. Lift up the front of the storage bin and pull it out.

Replace the bin by pushing it in all the way or the dispenser will not work. Push the wire shutoff arm down to the ON

position to restart ice production. Make sure the door is closed tightly.

NOTE: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or

after the system.

Water Filter Status Light (on some models)

The water filter status light will help you know when to change your water filter. The light will change from green to yellow. This

tells you that it is almost time to change the filter. It is recommended that you replace the water filter when the status light changes to red OR water flow to your water dispenser or ice

maker decreases noticeably. After changing the water filter, reset the water filter status light.

The status light will change from red to green when the system is reset.

Turning the Ice Maker On/Off

To turn ON the ice maker, simply lower the wire shutoff arm. To manually turn off the ice maker, lift the wire shutoff arm to the

OFF (arm up) position and listen for the click. NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will fill the ice storage bin, and the ice cubes will

raise the wire shutoff arm to the OFF (arm up) position. Do not

force the wire shutoff arm up or down.

REMEMBER:

• Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

• The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to poor quality ice. If asoftened water supply cannot be avoided, make sure the water softener is operating properly and is well

maintained.

• Do not use anything sharp to break up the ice in the storage bin. This can cause damage to the ice container and the dispenser mechanism.

• Do not store anything on top of or in the ice maker or storage bin.

Non-indicator Water Filter (on some models)

If your refrigerator does not have the status light, you should

change the water filter every 6 months depending upon your usage. If the water flow to the water dispenser or ice maker decreases noticeably before 6 months have passed, replace the

water filter more often.

Using the Dispenser Without the Water Filter

You can run the dispenser without a water filter. Your water will not be filtered.

1. Remove the water filter.

2. Slide the cap off the end of the filter and replace the cap in the base grille.

IMPORTANT: Do not discard the cap. It is part of your refrigerator. Keep the cap to use with the replacement filter.

3. Rotate the cap until it is securely in position.

REFRIGERATORCARE

Explosion Hazard

Use nonflammabme cmeaner. Failure to do so can result in death, expmosion, or fire,

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to prevent

odors from building up. Wipe up spills immediately. IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To prevent

odor transfer and drying out of food, wrap or cover foods tightly. To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window sprays, scouring cleansers, flammable fluids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior and door liners or

gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean sponge or soft cloth and a mild detergent in warm water.

There is no need for routine condenser cleaning in normal home operating environments. If the environment is particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Removethe base grille.

• Use a vacuum cleaner with a soft brush to clean the grille, the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

NOTE: Not all bulbs will fit your refrigerator. Be sure to replace the bulb with one of the same size, shape and wattage. On some

models, the dispenser light requires a heavy duty 10-watt bulb. All other lights require a 40-watt bulb. Replacement bulbs are available from your dealer.

1. Unplug refrigerator or disconnect power.

2. Remove light shield when applicable, NOTE: To clean the light shield, wash it with warm water and

liquid detergent. Rinse and dry the shield well.

3. Remove light bulb and replace with one of the same size, shape and wattage.

4. Replace light shield when applicable.

5. Plug in refrigerator or reconnect power.

+ 16 hidden pages