Ingersoll-Rand 8RSL32, 8 Series, 8RSM32, 8RSP53, 8RSQ53 Product Information
...
Air Angle Wrench
8 Series
Product Information
EN
Product Information
ES
Especificaciones del producto
FR
Spécifications du produit
PT
Especificações do Produto
80167505
Edition 1
September 2006
Save These Instructions
3
9
48h
10
PMAX
6
48h
4
8
7
48h
11
2
24h
5
(Dwg. 16585796)
3
1
2
I-R # - NPT I-R # - BS
6
5
inch
NPT I-R # I-R # cm³ I-R # cm³
(mm)
10
11
9
C28-04-FKG0-28 C28-C4-GKG0 1/2 (13) 1/2 10 66 1 28 1
1
2 80167505_ed1
EN
Product Safety Information
Intended Use:
These tools are designed to remove and install threaded fasteners.
For additional information refer to Air Angle Wrench Product Safety Information
Manual Form 04585006.
Manuals can be downloaded from www.irtools.com.
Product Specifications
Torque Range
Model(s)
8RSL32 Stall 12 (16.3) 18 (24.4) 1,200 Square 3/8”
8RSM32 Stall 15 (20.3) 23 (31.2) 930 Square 3/8”
8RSN32 Stall 19 (25.8) 30 (40.7) 700 Square 3/8”
8RSP53 Stall 26 (35.3) 40 (54.2) 510 Square 1/2”
8RSQ53 Stall 32 (43.4) 50 (67.8) 430 Square 1/2”
8SM32 Stall 16 (21.7) 23 (31.2) 1,110 Square 3/8”
8SN32 Stall 21 (28.5) 30 (40.7) 840 Square 3/8”
8SP53 Stall 28 (38.0) 40 (54.2) 610 Square 1/2”
8TM32 Shut-off 16 (21.7) 23 (31.2) 1,110 Square 3/8”
8TN32 Shut-off 21 (28.5) 30 (40.7) 840 Square 3/8”
8TP53 Shut-off 28 (38.0) 40 (54.2) 610 Square 1/2”
8TQ53 Shut-off 35 (47.5) 50 (67.8) 520 Square 1/2”
Clutch
Typ e
(soft draw)
50 psi
ft-lb (Nm)
90 psi
ft-lb (Nm)
Installation and Lubrication
Size air supply line to ensure tool's maximum operating pressure (PMAX) at tool inlet. Drain
condensate from valve(s) at low point(s) of piping, air filter and compressor tank daily.
Install a properly sized Safety Air Fuse upstream of hose and use an anti-whip device
across any hose coupling without internal shut-off, to prevent hose whipping if a hose fails
or coupling disconnects. See drawing 16585796 and table on page 2. Maintenance
frequency is shown in circular arrow and defined as h=hours, d=days, and m=months.
Items identified as:
1. Air filter 7. Coupling
2. Regulator 8. Safety Air Fuse
3. Lubricator 9. Oil
4. Emergency shut-off valve 10. Grease - through fitting
5. Hose diameter 11. Grease - through fitting
6. Thread size
Free
Speed
rpm Type Size
Drive
80167505_ed1 EN-1
EN
Parts and Maintenance
When the life of the tool has expired, it is recommended that the tool be disassembled,
degreased and parts be separated by material so that they can be recycled.
The original language of this manual is English.
Tool repair and maintenance should only be carried out by an authorized Service Center.
Refer all communications to the nearest Ingersoll Rand Office or Distributor.
EN-2 80167505_ed1
Loading...