InFocus SP-CEIL-010 User Manual

SP-CEIL-010 DIGITAL PROJECTOR MOUNT

These are the installation instructions for your Digital Projector Mount. Included are four methods of installation.

Select the method that works best for your viewing situation. The methods are:

NOTE: If the required height range is greater than 12½", the optional SP-LTMT-EXTP could be used to extend the length of the suspension adapter. For further information or ordering assistance, please contact us at the phone number and address listed at the top of this column.

° Fixed Height Ceiling Installation

° Adjustable Height Ceiling Installation

° SP-LTMT-EXTP-S height adjustable extension is required.

° Wall Mount Installation

SP-LTMT-EXTP-S height adjustable extension is required.

27700B S.W. Parkway Ave.

Wilsonville, Oregon 97070-9215

1-800-294-6400

www.infocus.com

nstallation Instructions

—

best for short ceilings, eight (8’) or lower

—

best for high ceilings, nine (9’) feet or higher

—

for installing the Digital Projector Mount on a rear wall the

Before You Start the Installation

The wall or ceiling where you want to install the digital projector must be capable of supporting a weight that is five (5) times the weight of 7lbs the projector you are installing. Consult the projector’s documentation for weight specifications. If the wall, ceiling, tabletop, shelf, or floor is not strong enough to handle five (5) times the weight of 7lbs, then you must reinforce the installation environment. If you are unsure about the installation environment, please consider having it reinforced and having the projector installed by qualified personnel. Failure to do so could result in serious personal injury and damage to the projector.

To avoid personal injury, use only an approved projector mount. Using an unauthorized projector mount may lead to poor ventilation and projector failure.

When installing the projector mount, keep in mind that the projector’s focus ring is not squarely in the center of the front of the projector, but offset by several inches. Make sure that when you mount the projector you offset the installation to match the amount of inches that the projector’s focus ring is offset from the center of the front of the projector.

LISTED

E176225

Hardware description

The Digital Projector Mount utilizes the following hardware. Note that the letters associated with the hardware on this list correspond to the letters listed in the instructions for each installation method.

. Four (4) 6 (mm) x 10 (mm) Phillips head screws (supplied)

B. One (1) mounting bracket (supplied)

C. Digital Projector (not included) D. One (1) Litemount Plus® assembly (supplied)

NOTE: Hardware item (E) is what secures the Digital Projector Mount to your ceiling, wall, tabletop, floor.

Make sure you consult with your local hardware store staff for the type of hardware that works best for your installation environment.

E. SINGLE WOOD STUD: If mounting on a single wood stud use three (3) #14 x 2" Lag bolts (minimum) commercially available. Use the mounting points on the center of the plate as indicated in the assembly diagram.

° SOLID STRUCTURE: If mounting to a solid structure use four (4) 5/16" x 2" Lag bolts or commercially available hardware (depending on the installation requirements). Use the mounting points found on the outer points of the mounting plate as indicated in the assembly diagram.

F. Allen wrench (supplied)

g p

(

Tools Needed for Installing the Digital Projector Mount

g p

You need the following tools to install the Digital Projector Mount:

• Phillips head screwdriver (not included)

• Allen wrench (included)

• Drill (for installation environment only -

• The commercially available hardware (E) that is required by your installation environment (not included)

Mount) and drill bit to match the hardware for your installation environment (not included)

do not

use a drill on the Digital Projector or the Digital Projector

Lightmount Plus® Overview

(4) Solid structure

mountin

oints

(3) Single wood stud

mountin

(2) Cable access points

Screen side

Yellow indicator)

(2) Tension knobs

djustable

extension

Safety knobs Red indicator)

Clamp plate

Lower assembly

oints

Ceiling plate

Getting the projector ready

Before you start the installation process, prepare your Digital Projector by performing the following steps

IGURE

1).

1. Turn the projector (C) upside down and place it on a clean flat surface, preferably on a towel.

2. Locate the mounting bracket (B) and align it over the holes on the projector.

3. Locate the four (4) 6 (mm) x 10 (mm) Phillips head screws (A).

4. Use the Phillips head screwdriver to secure the mounting bracket (B) to the projector via the three

(3) Phillips head screws (A). Do not over-tighten the screws.

IGURE

(Optional) Fixed Height Ceiling Installation

Complete the following steps to install the projector mount and projector on your ceiling. This installation works best with low ceilings (F

Note: Look at the bottom of the mount assembly (D) and locate the arrow. Make sure you install the projector mount with the arrow pointing toward your screen.

1. Remove the upper plate from the assembly (D) secure to the ceiling structure using the commercially available hardware (E) suitable for your environment. Be sure that the mount assembly screen indicator arrow is pointing toward your screen.

2. Replace the mount assembly with the upper plate and fully raise the safety knob and tension knobs all the way. Carefully raise the projector (C) with the mounting bracket (B) attached and insert it into the bottom of the mount assembly (D) by its tabs.

3. Rotate the projector (C) with the mounting bracket (B) attached 180º is pointing toward your screen.

4. Align the safety knob on the mount assembly (D) with the end of the arrow-shaped slot on the mounting bracket (B) and screw it through the opening to prevent further rotation. Hand-tighten the safety knob.

5. Hand-tighten the remaining two tension knobs to secure the mounting bracket (B) to the mount assembly (D).

CAUTION: Check all of the hardware for proper tightness and security. Do not over-tighten the screws.

IGURE

2).

so that the projector’s focus ring

+ 3 hidden pages